Search Documents

By Scott King, Norm Patterson, Ruilin Yang

The multiple blasthole fragmentation (MBF) model developed by Orica models the contributions from multiple blastholes to fragmentation at any given point in the rock and simulates a production blast with the actual geometry of the blasted overburden and free faces, explosive loading, multiple decking, and delay timing of each explosive charge. The model has been successfully applied to several open pit mines and quarries around the world, including Canada and the United States. The peak particle velocity (PPV) induced in the rock from the explosive detonation is used in the MBF model as the key parameter relating to the size distribution of the rock fragmentation. Relating the PPV to the rock fragmentation is based on earlier work relating the particle velocity to the dynamic strain in rock. A recent publication further revealed that the PPV is related to the maximum relative displacement that induces three dimensional strain at a point in the rock. The model can explicitly model most of the blast design parameters including explosive properties.

Jan 1, 2018

By A. Andrades, E. Arias, Y. Pizarro, J. Alarcón

Division Ministro Hales - Codelco (DMH) is located at 2600 meters above sea level, 10 km north of the city of Calama, Antofagasta region, Chile. In operation since 2010, it corresponds to a porphyry copper deposit that is exploited by the open pit mining method. The ore is mainly composed of sulfides, which is concentrated by comminution processes such as crushing, SAG milling and ball milling to liberate the mineral particles, and then separated from the waste (concentrate) in flotation stages, including a concentrate regrinding stage. Reports from the DMH processing plant area have identified a decrease in fine copper recovery, with the first hypothesis being the high percentage of ultrafine particles (% <45µm) in the flotation feed. Due to the above, DMH & Orica decided to carry out activities to identify the controllable variables that can impact the generation of low size particles in ore and adjust them to reduce the percentage of fine material generation, with special focus on the Drilling and Blasting processes. Based on the data provided by DMH, we evaluated what could be integrated to make an analysis. The different attributes associated with the ore and their effect on copper recovery were evaluated. In parallel, at the mine, a fragmentation measurement campaign was carried out at the loading faces and granulometric analysis of the drill cuttings. Once the correlations between the attributes and copper recovery were identified, hypotheses were established and reviewed with the Drilling & Blasting, Geotechnical, Geology and Process Plant areas. With the validations of the hypotheses and the results of the in-mine (cutting) measurements, we proceeded to review the criteria for the classification of Blastable Geotechnical Units and their associated D&B designs. Using software and the Crush Zone Model (CZM) tool, which considers rock and rock mass parameters, scenarios for various D&B design proposals were simulated with the objective of reducing the generation of ultrafine particles from the blasting process. Next steps include trial blasting with the D&B design recommendations, which will require follow-up to the flotation process to identify the impact on the reduction of ultrafine material from blasting.

Jan 1, 2024

By CVB Cunningham

"The Kuz-Ram model as originally proposed included an error in assuming that the mean fragmentsize predicted by Kuznetsov’s equation was actually the 50% passing size. In 2003 Spathis began discussions on this issue and recommended correcting the equation. The correction produced more fines in the predicted fragmentation, which had been a criticism of some users of the original model. Ouchterlony subsequently showed that the error had, if anything been beneficial, and that the Swebrec function adequately covered the fines. This author shows that the Spathis correction does not assist the fines correction in examples examined, but tends to underestimate coarser fractions. An intrinsic problem of communication between academics and engineers is a root of misunderstanding on both sides, and requires patience by both parties to enable value to arise."

Jan 1, 2016

By Braden Lusk

A typical rural house surrounded by a surface coal mine was instrumented in 2008. Information regarding ground vibration, airblast, and sounds inside the house was collected. Previous publications have included conclusions about this data with regard to blasting source (far-field or near-field) and results as to how the residents experience the blast were made. Several events were also recorded that were not related to blasting due to the nature of the trigger system. The trigger of the monitoring system was attached to one of the mid walls of the house, thus other normal daily events produced vibration levels significant enough to trigger the monitoring system.

Jan 1, 2011

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By Reinhold Daykin, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e., metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine.

Feb 1, 2020

By Tapan Goswami

The main objective of the blasting phase in a coal mining operation is to maximise the coal recovery. However, coal loss due to blasting is a serious problem. The Australian Coal Association Research Programme (ACARP) reported in 2011 that in Australia one in every ten coal mines is completely wasted due to such losses. Coal is either lost in the spoil, largely due to the blasting operation or becomes diluted and cannot be recovered entirely. The major coal loss mechanisms include losses from the coal seam roof, the floor, the front edge and from dilution. Coal damage and loss mechanisms during cast blasting that have been observed by various authors include: •Excessive cast dragging the coal edge in the cast direction. Movements of this nature are oftenassociated with the formation of trenches. •Spatial movement of overburden where rock shears and moves in a plane above the coal seam,which damages and dilutes the coal. •Rock falling over the coal during the blast often producing indentations in the exposed coal. •The inappropriate use of bulk and initiating explosives that often results in coal damage. •Insufficient stand-off distances from the coal. The Australian coal mining industry has gone a long way towards addressing the coal loss issues since 2011: almost all operations now deploy touch-coal drilling and sporadically use gamma logging for loading overburden. A study was conducted to compare the effectiveness of touch-coal information in which some touch-coal blastholes were drilled on a fixed or random pattern. In another study, some blastholes were drilled to the touch-coal, gamma-logged and mapped to determine stand-off distances. It was found that the coal roof surface created by gamma-logged holes was the most effective option for minimising coal loss. As a result, a variable stand-off distance was found to be the key to minimising losses. This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By Z X. Zhang

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Hairong Zeng, Matthew Baumann, Shahram Tafazoli, Edmond Chow

Measurement of rock fragmentation has evolved from a completely subjective and manual process to a statistically objective and semi-automated process. However, ultimately, the vision is to achieve a statistically representative and fully-automated process. From the blast optimization perspective, it is critical to receive reliable rock fragmentation results quickly to incorporate into the planning of subsequent blasts. Since manual rock fragmentation measurement methods tend to be time consuming, a fully-automated method is the practical way to meet these requirements.

Jan 1, 2012

By Miie Shields, Ed Billington

Trail blasters for the National Park Service (NPS) live and work in remote mountain terrain throughout the western states, where any support or resupply may be sporadic and ditlicult and mountain weather affects every activity. Mechanical “aids” are the pick, shovel, rock-bar, wheelbarrow, and a Pionjar or Cobra dritl. The blaster is usually faced with an extraordinary range of work, t?om delay blasts in weathered rock using driiole depths of 18” (46cm) to as little as 4” (1 Ocm), through reducing boulders and talus fields to useable tread, blasting stumps, snags and log-jams, to the explosive disintegration and casting of animal czcasses. One day he/she might provide a 500cf (14 cu meter) anchor excavation for a suspension bridge, the next day directionally fall 60” (1.5m) diameter snags in a camp area, and the following day blast a 3-foot-wide (1 meter) tread bench across a steep bedrock slope. To be effective, the blaster must design each and every blast around desired end result, crew and public safety, maximizing effective use of limited quantities of explosive, and the minimnation of environmental effects. Since almost all drillhole blasting occurs in the weathered zone of the rock, blasting is more the art than the science of judging rock density, hardness, cohesion and prefracturing, and selecting explosives, drill and delay patterns, and loading techniques responsive to those conditions. For these reasons the NPS issues its own Blaster’s License, with a basic requirement of at least 40 hours of NPS blaster training and 3 years of supervised Blaster in-Training experience. The focus of this pre-license requirement is on safety and using explosives as a precision tool, versus just “blowing things up”.

Jan 1, 2002

By Marcus Neves, Eventomar Junior, Adilson Castro, Leandro Silveira, Sérgio Augusto

The collapse of the Vale S.A. mining tailings dam in 2019, a tragic event that shook Brazil and the world, had consequences that transcended the immediate pain and devastation. Among them, the suspension of rock blasting activities in several mines in the Quadrilátero Ferrífero region of Minas Gerais, Brazil. This measure, taken as a precaution and with the aim of ensuring the safety of nearby geotechnical structures and the population, had a significant impact on the mining production chain. To overcome these challenges and resume blasting activities in a safe and sustainable manner, the mining industry has been dedicated to developing and improving solutions. One of the promising alternatives is the signature hole technique, used in conjunction with attenuation laws. The complex geology of the Quadrilátero Ferrífero, with lenses of compact ores immersed in friable materials, the presence of discontinuity families, and the emergence of geological faults, requires detailed analyses and specific adaptations of the signature hole technique and constant monitoring of the vibrations to calibrate the attenuation laws to ensure compliance with permissible limits and safety of the operations. To demonstrate the methodology, a case study in Abóboras Mine was described. Additionally, the challenge of achieving the desired level of production while controlling vibration and slope damage has driven the development of new charging and timing techniques. To address this challenge, a comprehensive approach was undertaken. A substantial database containing more than 4,000 registers of blasting-induced vibration events from 520 blasts was meticulously compiled from 2020 to 2023, 6 different attenuation laws were established and continuously calibrated with 99.3% of compliance regarding permissible limits of vibrations. The successful implementation of these actions allowed for the resumption of blasting, increasing production from 10 million metric tons to 43 million metric tons per year assuring sustainable operation.

Jan 21, 2025

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Martin Langenderfer, Sergii Chertopalov, Catherine Johnson, Vadym Mochalin, William Fahrenholtz

The high temperature and high pressure of an explosive detonation can be used for the production of nanomaterials. The controlled detonation of explosive compositions along with the collection and characterization of reaction products encompasses a process known as detonation synthesis. The primary advantage of the method of detonation synthesis is the possibility for producing monocrystalline nanoparticles with diameters of less than 10 nm. In order to successfully synthesize nanomaterials via the detonation process, it is necessary that the explosive detonation is conducted in a sealed environment. This environment when pulled to a vacuum or purged with inert gas such as argon will reduce the oxidation of detonation reaction products. Detonation synthesis testing is currently being conducted in a 1.8 cubic meters (m3) (64.3 cubic feet (ft3)) ellipsoidal pressure vessel consisting of two interlocking half shells. The testing involves the controlled detonation of cast mixtures of Cyclotrimethylene-trinitramine (RDX) and 2,4,6-Trinitrotoluene (TNT) in conjunction with siliceous compounds to produce nanocrystalline diamond and silicon carbide. Alternative detonation environments including the presence of a cooling medium such as water or dry ice to absorb residual, post detonation, thermal energy and enhance the stability of the materials being produced have improved yield. Modifications to the explosive charge composition have an effect on the type and quantity of materials that can be produced. Doping of explosive charges with various organic and inorganic compounds has shown promise in the synthesis of materials that are difficult or uneconomical to produce through other methods. This paper outlines the process development of detonation synthesis facilities. Preparation of the pressure vessel to create a suitable detonation environment for the production of nanomaterials is examined. Formulation of explosive charge compositions and considerations involving test charge initiation are discussed in detail. Experimental results and analysis from initial testing as well as plans for future research are also evaluated.

Jan 1, 2018

By C. T. Aimone-Martin, V. L. Rosenhaim

The response of two structures to blast-induced ground vibrations were evaluated and compared in order to quantify the impact of different blasting operations, hard rock and soft rock blasting, upon the structures movements. The first instrumented structure was a residential type, located in the operational area of a coal mine, were blasting is conducted in soft rocks, such as siltstone and coal, with compressive strength ranging from 20 to 50 MPa. Blasting is characterized by low benches, with hole lengths averaging 5.5 m (18 ft) and low powder factors, 140 to 210 g/m3 (0.236 to 0.354 lb/yd3), resulting in very little horizontal movement of the rock during the blast. The second structure was a commercial building, located in a basalt quarry (compressive strength between 109 and 180 MPa), where blasting is conducted in 12 m (39.4 ft) benches with powder factors ranging from 200 to 350 g/m3 (0.337 to 0.590 lb/yd3). Velocity sensors were placed on the structure walls to measure wall displacements and calculate blast-induced strains in the walls, and these results were compared with the driving ground excitations. The calculated strains were compared with the limits of rupture of the cement grout used as mortar between bricks and as wall coating, considered to be the weakest material in the structure composition. The blast-induced response of existing cracks in the structures were also measured using displacement gages and compared to the daily influence of weather fluctuations, such as changes in temperature and humidity, on crack movement. The results show that for the same levels of ground motions the structures present different movement, resulting in distinct levels of induced strains on the walls depending on the geology. The influence of long-term temperature and humidity variations on crack movements on both structures is very similar, during the same seasons of the year. Crack response to long-term weather changes is 2.5 to 3.5 times greater than blast influences.

Jan 1, 2015

By Peter Moser

The average annual consumption of raw minerals in Europe is 10 ton per person. About 50 % is produced by blasting. For a population of 450 million (including the population from the countries of the new member states) this makes 2.25 billion tons of blasted rock, 80 % being building industry aggregates and industrial minerals. In aggregate quarries 10-15 % of the rock blasted can’t be sold, as the material is too fine, i.e. smaller than 4 mm. This ‘fines problem’ is worse in the quarries of limestone and cement producers where up to 30 % of the material is useless. Thus about 450 million tons of useless rock fines are produced and put on waste dumps every year, i.e. 1 ton/person. This problem is addressed by the research project LESS FINES - “Less Fines production in aggregate and industrial minerals industry” which is funded by the European Union under the project contract G1RD-CT-2000-00438. The project consortium, formed of nine partners from 5 EU countries, works on the following two main research subjects: 1. The determination of the natural breakage behavior (NBC) of the rock mass, which is defined as the particle size distribution curve for a certain rock mass with the maximum uniformity and thus for a given maximum particle size that fragmentation curve which gives the minimum amount of unusable fine material. The comparison between the NBC and an actual blast fragmentation curve allows to quantify the fines reduction potential. 2. The adaptation of explosives properties, charging techniques and timing in order to produce only the minimum, inherently unavoidable percentage of fines. With about 15 full time working persons the project is estimated to be one of the largest blast related research activities in Europe at the time of the project period. The project is coordinated by the Department of Mining Engineering& Mineral Economics of the University of Leoben.

Jan 1, 2004

By B. Corrêa, M. Cavalcante

A large open pit iron ore mine in Brazil, which has a heterogeneous lithology, faces a challenge in defining drill and blast patterns to achieve the expected results. The mine needed to obtain an automated representation of the fragmentation curves and correlate them to the respective blasts, lithologies and quality parameters, seeking the continuous optimization of the fragmentation process and its benefits to the subsequent comminution processes. Trials were carried out for 5 months to demonstrate the functionality of an autonomous fragmentation monitoring system that analyzes the granulometric curve of the material throughout the muckpile and makes the results available online and in real time. The system, which contains a binocular camera, a processing unit and an antenna, was installed in a shovel, to evaluate the following KPI's: monitoring failures, monitoring capacity, physical availability and reportability of oversized boulders. The system analyzed 33,060 samples, with an average capacity of 285 photos every 24 hours, 127 during the day and 158 at night, all measured, analyzed, stored, and made available on its online platform, reporting 223 alerts of P80 above 400mm (15.7 in) and 38 particle sizes above 900mm (35.4 in). The inactive and operational hours of the monitoring system corresponded, respectively, to the idle and worked hours of the shovel, according to dispatch data. There were no camera or processor failures, and rain, dust or poor internet conditions did not impact sampling and fragmentation analysis, indicating 100% physical availability of the system. The autonomous monitoring analyzed 139 times more samples compared to the currently used manual method. In addition to increasing sampling representativeness and automating the process, it increases the safety, quality, and productivity of granulometric analysis, eliminating the exposure of people in the mine and human bias in the analyses. Additional analyses were performed by correlating digitally centralized drill and blast data, data from autonomous drills and fragmentation results. Automated obtention of granulometric curves favors quick decision-making and optimization of blasts to achieve better results in productivity and cost reduction in the plant and mine operation. The autonomous fragmentation monitoring system met the need presented by the mine, proving to be a key tool in continuous improvement projects, including Mine to Plant.

Jan 1, 2024

By C. Feliciano, M. Cavalcante

A large iron ore open pit mine in Brazil operates with reduced blast sizes, due to the imminence of red alerts in the rainy season and the proximity of plant and dam structures that demand control of the maximum load of fired explosives. Blasts are currently not allowed to remain loaded with explosives due to the risk of red alerts, limiting mine operations close to them. There is a need to increase the blast sizes, reducing the number of events required to obtain the planned mass and, consequently, the unproductive operating hours lost with mine evacuations. The WebGen™ wireless electronic initiation system is a technology for firing detonators via lowfrequency magnetic induction that propagates through the medium, without physical connection. A blast was carried out with 406 holes divided into 4 panels, aiming to validate the preloading technique with wireless detonators and its performance in safety and productivity. The absence of lead wires in the system eliminates the risk of interaction between vehicles and detonator cables in stemming and loading operations, which can result in unplanned detonation or misfire. By eliminating the need for a spotter, it reduces people's exposure to dust and the risk of human-machine interaction. Furthermore, it eliminates the risk of unplanned detonation caused by lightning strikes. The pre-loading technique with wireless detonators enables flexibility and efficiency in planning through temporary accesses over loaded areas. In the demonstration, driving over the loaded area was essential to avoid jams and excessive wear on equipment due to the narrow berm and very friable material. Another gain in productivity was optimizing operational stages, since detonators were programmed in parallel with loading, anticipating process stages, in addition to eliminating the need to connect detonators. Considering the average handling and savings in downtime due to the reduction of blasting events, a potential increase in movement of 49,000t (54,013 short tons) in 3 months was estimated, keeping the vibration results within the required limit. The trial with wireless detonators demonstrated the feasibility of carrying out blasts with preloaded panels, without restrictions on the number of panels or detonators, enabling vibration control, innovating mine planning and increasing safety and productivity

Jan 1, 2024

By Travis Davidsavor, Stanley: Dong Vitton

Concrete is a common construction material used throughout the world, and with increasing demand of fast-track construction, blasting and concrete casting are occurring simultaneously at many sites where rock is being excavated for concrete placement. However, there has been significant disagreement in the construction industry as to what intensity of shock vibrations green, or fresh concrete can tolerate. Peak particle velocities are often arbitrarily chosen, or are simply based on materials such as plaster and drywall that have been more thoroughly studied in relation to damage. Previous research on green concrete has used the concrete’s static strength subjected to shockwaves at different ages as the primary damage criteria. In addition, the static strength tests have been based on curing time. However, changes in temperature or humidity can dramatically alter the hydration rate, which affects strength development of different cements. To account for temperature changes and humidity the concept of concrete maturity is commonly used and allows the researcher to see where the concrete was in terms of hydration progress. In general, static testing determines the failure stress that the concrete’s macrostructure can handle, and often failure occurs in the natural materials first or along large defects in casting techniques. Dynamic testing or high strain rate testing, on the other hand, loads materials at such a high rate that larger defects do not have time to react and instead the microstructure is more highly stressed leading to higher strength and stiffness values. This is known as the material’s strain rate sensitivity. Since dynamic testing better tests the microstructural strength, it is believed that it may provide a better way to assess damage to green concrete. Testing includes both static and dynamic compression as well as static and dynamic splitting tensile strength to assess whether damaged has occurred to the concrete. No significant statistical evidence was discovered that damage to the concrete occurred at five different “green” maturities from peak resultant velocities ranging from 10.66 in/s (271mm/s) to 4.40 in/s (112 mm/s) with average intensity of 6.7 in/s (170mm/s).

Jan 1, 2003