Search Documents

By Michael Twomey, Alastair Torrance, Alan Twomey

Low density explosives have been available in various forms for nearly 20 years. These initially consisted of various diluted forms of ANFO formulated to slow the rate of reaction. One such product that was developed was a blend of ammonium nitrate and rubber. This product uses a coarse fuel provided by granulated rubber to slow the reaction rate of the explosive rather than being a diluted form of ANFO. There has always been a technical difficulty in blending two dissimilar materials without subsequent segregation.

Jan 1, 2011

By Jason Baird, Philip Mulligan, Caleb Baumgart

This report details the pressure variances, measured at four pressure sensors placed equidistant from the center of an airburst explosion, as the blast pressure from a single charge expands radially. Many of the empirically derived equations used for predicting the blast pressures of an explosion, assume a point source detonation and that the radial pressure expansion is equal. The authors understand that the equations used to approximate the blast pressure may not have 100 percent agreement with the observed pressure. However, during previous research at Missouri University of Science and Technology (Missouri S&T) the pressure variances had a range of 1,200 psi, between the four pressure sensors placed two feet from the center of a 1/2-pound (226.8 gram) of hand packed C4. The variances indicated that at the close distance from a suspended explosive charge the pressure does not behave as that observed from a point source.

Jan 1, 2014

By Italo Onederra, Miguel Araos

"Most of the current explosives for mining blasting activities are based on ammonium nitrate (ANFO, emulsions and watergels). AN-based explosives’ detonating properties were discovered in the 50’s and since then they have proven to be reliable, safe and cost effective. However, there is no current alternative raw material to replace AN. As part of a program of research initially funded by the Australian Coal Association Research Program (ACARP), Mining3 and the University of Queensland engaged in the search for potential oxidizing agent alternatives that could replace AN in the manufacture of mining explosives. Candidates included those that are produced in large quantities and that can be cost competitive with ammonium nitrate. The initial work identified hydrogen peroxide (HP), calcium ammonium nitrate (CAN) and sodium nitrate (SN). Explosives mixtures were prepared and sensitized using void sensitization techniques. The detonation properties results showed that explosives based onmixtures of HP/CN and HP/SN as the oxidizer were able to detonate in a range of 2000 – 5000 m/s, indiameters 50 and 102 mm, and densities in the range of 0.50 – 1.40 g/ml. Although more studies need to be conducted to fully understand these explosives, if successful, these explosives would be able to offer an alternative to the AN-based explosives in the mining industry."

Jan 1, 2017

By Ethan Steward, Robert Eades, Kyle Perry

Shock tubes, either gas or explosively driven, are often used for physical modeling of free field explosions or arena testing. The use of shock tubes often requires less setup time of subjects and smaller driving forces to create pressure versus time waveforms similar to that of arena testing. However, the effects of the shock tube cross sectional geometry on waveform properties is uncertain while free field explosion wave propagation and estimation is well studied.

Jan 1, 2018

By Tom Watts

The practice of pumping bulk blasting agents is regulated by many agencies around the world. The explosives manufacturers have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping of water based blasting agents. The challenge of a Bulk Trucks or Mobile Manufacturing Units (MMUs) manufacturer is to take the objectives of the regulatory agencies and the explosives manufacturers and responsibly design and build MMUs that are safe, compliant, and cost effective without compromising serviceability.

Jan 1, 2011

By Robert B. Hopler

Reefs, exposed rocks, and fast currents made the Hell Gate section of New York's East River a treacherous passage ever since man attempted to sail through the area. As the harbor's importance grew, attempts to improve the channel were made, starting in 1851. This paper discusses the first major organized effort to clear the area, which began in 1869 and culminated in a single large blast in September 1876.

Jan 1, 1981

By Scott Scovira

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one NA Quarry and Construction Business experienced a series of flyrock incidents. In the Spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Jaco van den Berg, Dr. Todor Petrov, Dr. Josh Calnan, Dr. Jhon Silva

This paper shows and reviews the similitudes and differences in explosions generated by high explosives and gas explosions, the reasons why gas explosions are difficult to replicate using high explosives, and the considerations when performing explosive testing using methane gases and coal dust.

Feb 1, 2020

By Ron Stewart, Richard Youmaran, Andy Adler

In the current context of heightened concerns with explosives security, there is significant interest in technological controls to improve security. It is important to be able to control what is fired, by whom, where and when. This paper describes research Orica has performed to investigate and test biometric systems to address the question of "by whom". The goal of this research is to incorporate the most suitable biometric system onto the 'blaster' unit of an electronic initiation system. This approach will ensure that only authorized personnel can initiate a blast involving electronic detonators. Requirements analysis: we initially explored many different biometric technologies to evaluate them against the requirements, including security, usability, ruggedness, size, form factor, privacy, and operational temperature range, This analysis identified chip based fingerprint sensors as the best candidate. Development of prototype units: in order to test the identified sensors, we modified standard, commercially-available, electronic blast initiation units ("blaster") to incorporate a fingerprint reader. Testing and evaluation: Biometric We conducted a biometric scenario evaluation in order to determine: 1) security level (measured by false accept rate (FAR)); 2) usability (measured by failure to enroll (FTE) and false reject rates (FRR)), and to 3) discover environment specific issues and challenges (such as temperature, humidity, dirt, or those related to the usage patterns of the user group). Tests were conducted at quarry sites in eastern Ontario, Canada. Results show rates of: FAR= 0%, FTE= 1.67%, FRR= 28.81%. Overall, these results suggest that this fingerprint biometric technology has a good level of usability in this application of electronic blast initiation control.

Jan 1, 2007

By Catherine T. Aimone

A series of experiments have been performed to characterize fragmentation and microcracking in quartz monzonite copper porphyry. The flyer plate impact method was used to generate plane shock waves in rock specimens for impact pressures between 1.6 and 7.3 GPa and impact pulse durations between 1.1 and 7.0 µs. The effects of pressures up to 4.8 GPa and pulse duration on fragment size distributions and microcrack densities were studied. The results show that pressures effect particle sizes to a greater extent at higher pulse durations. However, changes in pressure and pulse duration show little influence on the density of microcracks induced during explosive loading. These results indicate that the nucleation and growth of microcracks in rock subjected to shock waves occur uniformly throughout. A substantial decrease in particle sizes for high pulse durations is attributed to more time allowed for microcracks to grow and coalesce, forming individual particles.

Jan 1, 1985

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985

By Matheson and Miller

Does anyone have any definitive information on vibration limits for damage to well casings near blasting? Also, are people using self-imposed limits when approaching cased wells? I can only tell you what I have personally done with success. Often in new construction in hard rock, the well is drilled before the foundation is excavated and before the ditch for the water line is excavated. These both require drilling and blasting. Under these circumstances when blasting for the ditch for the waterline we will drill right up to within 10 inches (not feet) of the well casing. We drill line holes the width of the ditch, then about a foot from this, another row of trim holes then as we move away from the casing holes for 1 1/4 inch stick powder for about three rows then as we get further still, we can load with ANFO. I do not have vibration data for this but my experience has been that as long as you are not displacing the material into the casing that no damage is done. These typically are steel casings for residential water service.

Jan 1, 2010

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By Douglas Bartley

As the economy continues to slowly recover, our industry continues to finds ways to increase productivity while being forced to cut costs. The drilling and blasting process is the starting point of any aggregate or mining process. Many people refer to it as the “Primary Crusher” as it will always be more efficient to crush rock with explosives energy than it will be mechanical energy. It is the more efficient use of this energy that is addressed in this paper.

Jan 1, 2012

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By Vitor Barcelos, Eduardo Elói, Gabriella Vaz, Davi Oliveira, Leandro Silveira

Following a routine production blast at Vale S.A.'s Itabira Mine in the Quadrilátero Ferrífero region of Minas Gerais, Brazil, nearby residents registered complaints about blast-induced vibrations. Analysis of the blast footage revealed that multiple blastholes were detonated simultaneously, resulting in a higher-than-expected charge per delay, ground vibration and cratering even though the electronic delay timing was configured correctly. Subsequent blasts within the mine's soft schist region confirmed the occurrence of sympathetic detonation. Mitigating or eliminating this phenomenon is critical for the mine's operation. Two dynamic pressure tests were conducted using carbon resistors together with typical VOD monitor maintaining the standard booster, electronic detonator, and a blend of 70% emulsion with 30% ammonium nitrate explosive. The tests involved increasing the distance between the central hole (detonated first) and the four surrounding holes in a five-hole sequence. Unfortunately, sympathetic detonation occurred in all these tests. To address this issue, a new explosive with a lower density and detonation velocity was tested. This approach proved promising, as no sympathetic detonation occurred. By leveraging the data obtained from this study, engineers can now identify situations at risk of sympathetic detonation and implement preventive measures, such as selecting the appropriate explosive and recommending safe minimum burden and spacing settings as well as confinement level for each blast while maintaining the desired level of rock fragmentation.

Jan 21, 2025

By Tom Paynter

In an underground mining environment, the primary method of firing a blast is using a combination of an electric detonator and a detonating cord to initiate the Nonelectric detonators. This method has been in use since the 1970’s. A firing line is used which can be subjected to damage and the need for constant testing and maintenance.

Jan 1, 2017

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By G Mendoza, L Taddei, C Robertson

It is a well-known industry fact that many mine sites around the globe experience blast holes that have elevated temperatures due to reactive ground, geochemical reactions, geomorphic reactions, sub level open fires, etc. It has been reported in many previous industry publications (White, Saputra et al) that elevated blast hole temperatures are a norm at many mine sites and are dealt with on an ongoing basis while the drill and blast process continues under elevated states of alert. The choice of explosives products including the type of detonator, primer, accessory, and bulk product all must be taken into consideration when loading blast holes where there is a known potential for elevated temperature conditions. It should also be noted that these elevated temperatures inside blast holes can be consistent throughout the blast hole length or vary in position within the blast hole depending on the mine conditions mentioned in the opening statement above. The risks associated with the loading of primers and bulk explosives in holes where elevated temperatures are present include: the ejection of the bulk explosives product, deflagration of the explosives during initiation of the blast or premature and uncontrolled initiation of a blast hole(s). This paper describes a unique and novel approach to the active monitoring of the temperature within blast holes with the application of electronic detonators with integrated temperature measuring (ITM) capabilities, deployed and demonstrated at a mine site in Mexico during January 2023 to March 2023. The deployment of ITM capable electronic detonators allows a user to monitor and record the real time temperature at multiple locations (e.g., toe, middle and collar) at each electronic detonator’s position within the blast hole, with the ability to react instantaneously to elevations in temperature reported. The measurement of the temperature can be for a single ITM electronic detonator, or simultaneous for an array of ITM electronic detonators, allowing for the potential for the data to be represented by a time/temperature/hole depth three-dimensional heat map. Changes in temperature at different borehole positions can vary, however, often the collar position is expected to be the most reactive due the combination of bulk explosive product and oxygen exposure, which can be confirmed with the application of the ITM electronic detonators. A mine site’s reaction to a measured elevated temperature within a blast hole can vary depending on the temperature measured and the change in temperature from the last measurement made. The study was found to produce real-time in-hole temperature information which was previously unobtainable without the introduction of another device. New and adaptive elevated temperature hole policies can be created and adapted proactively as real time information is received, leading to a safer mining operation.

Jan 21, 2025