Search Documents

By Thomas L. Barkley

This paper describes an unusual design for a 12 foot diameter, 30 foot deep circular shaft shot in a close in urban environment less than 100 feet from occupied structures. It uses diagrams, video footage, and vibration results to describe a 3 deck, 17 hole burn round used to pull 17 feet in one lift.

Jan 1, 1994

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Shazad Hosein, Rob Farnfield, Bill Birch, Liam Bermingham

The propagation of a shock wave through air as a result of quarry blasting consists only of one type of wave, the compression wave. This is in marked contrast to seismic waves where a number of different types of wave are generated by the one blasting event. Even so the interaction of the burn time of a single hole and the resulting air overpressure is still too complicated to be able to be accurately modelled from first principles. It is considered that the best way forward is to monitor an individual single hole to obtain a signature wave form that has resulted from this complex interaction. Once this wave form is known, the variation in geometry of a mutli-hole blast and the timings of the successive detonations can be modelled to give a sufficient degree of accuracy to recreate the likely magnitude, duration and wave form of a multi-hole quarry type blast. This can then be directly compared with actual air overpressure wave forms from quarry blast to verify the model.

Jan 1, 2012

By J R. "Dick" Daniel

In the fall of 1988, The Cannon mine decided to investigate a central blasting system based on conventional electric blasting detonators being used to initiate rounds primed with Nonel detonators. The advantages of this hybrid detonator system were viewed as being safety and cost effectiveness. A study was done reviewing the safety aspects of utilizing a permanent blasting line installed throughout the main haulage drifts to a central blasting station located at the mine portal. The study addressed the following potential safety hazards: radio frequency induced current, stray current from both electrical utilities and transmission lines, galvanic and electrostatic sources of extraneous current.

Jan 1, 1989

By V R. Sastry, D P. Singh, N R. Thote

Rock parameters which are uncontrollable impose restrictions on the procurement of desirable fragmentation. Blast design parameters which are controllable prove to be important tool in blasting operations. An attempt was made by the authors to investigate parameters which causes big oversize boulders in overburden blasting. A case study of coal mine is discussed in this paper.

Jan 1, 1995

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Michael S. Wieland

The stress waves generated during delay blasting in underground or surface mines not only fracture the surrounding coal, rock, or other strata, but also impact delayed charges remaining in neighboring boreholes. This crossing wave interaction is a ubiquitous fundamental damage mechanism, ultimately responsible for numerous occurrences of misfires and flyrock. The hazards and waste from wave-induced malfunctions are Just the recognized tip of the iceberg. Undetected marginal performance of damaged delay detonators and desensitized charges poses a tremendous unresolved problem, resulting in the reduction of mining profits and the certain retention of unwanted risks.

Jan 1, 1988

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By Scott G. Giltner, Paul N. Worsey

During the short duration of an explosive blast, many events occur which are too quick to be detected or observed in detail with the naked eye or by normal photographic techniques. Through the use of "hightech", high speed video, many of these events can be observed, instantly played back and recorded for later use. The use of a Spin Physics SP 2000 Motion Analysis System at a blast casting operation is presented. The variable range of recording speeds offered by the SP 2000 allowed it to be used for examination of different areas of blasts. At its maximum full frame rate of 2000 frames per second the SP 2000 can easily pick up the flame front as it travels down a nonel tube and the flash from the surface delays as they fire. The system was used for a variety of tasks including, but not limited to,the determination of delay accuracy to within 0.5 ms, the velocity and trajectory of the faces during blasts, and pinpointing geological problem areas. The effectiveness of the system as used on site is discussed along with detailed method of set up, recording, playback and data processing. Other details including site specific environmental and lighting problems are also covered.

Jan 1, 1986

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lime Companys new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By Ruilin Lang

This paper presents an application of 3-D plots and non-linear regressions to define a sitespecific form of the charge weight scaled distance. The PPV (PPA) of single hole blasts is normally considered as a function of two independent variables - the charge weight and the distance. It is of great importance to obtain the relationship of the function accurately for a concerned site in terms of blast vibration analysis and modeling. However, in pre-computer time it was difficult to plot 3-D graphs. Consequently, a charge weight scaled distance was used to plot the PPV (or PPA) against the scaled distance as 2-D graphs. Blast vibration investigators use several forms of the charge weight scaled distances to plot data. We can exemplify them with the cube root of charge weight scaled distance, the square root of charge weight scaled distance, and other forms (Hossaini and Sen, 2004). Each of these scaled distances assumes relative contributions of the charge weight and the distance to the vibration attenuation. For example, the charge weight is assumed to have a less contribution to vibration in the cube root scaled distance than it is assumed in the square-root scaled distance. In reality, for different sites the relative contribution of the charge weight and the distance may be different and site-specific. This may explain that in some cases, the blast vibration data plots using these charge weight scaled distances are scattered. This could be largely due to the fact that the definition of the form of the charge weight scaled distance is not adequate for the particular site condition.

Jan 1, 2006

By Jonathan D. Aubertin

The unique nature of rock salt blasting is compared to traditional hard rock practices. Rock salt geomechanical nature is discussed in the context of rock blasting events. A cratering mechanism prevalent in soft rocks is presented and exemplified through a series of single hole blast tests performed in salt deposits.

Feb 1, 2020

By Barbara A. Sciever, John H. Sr Schue

Riverboat gambling has caused quite a sensation among people since its talk of coming to Illinois. The year 1992 marked the start of an era for people that had a penchant for gambling, it was the year that riverboat gambling was legalized in the State of Illinois.

Jan 1, 1995

By Wawa Jaka Sungkawa, Slamet Rachman Jaka, Tom Dermody

A project was undertaken to research and develop a method to confidently predict vibration. It was decided that the scaled distance formulas were not adequate to predict vibration when using non-electric detonators, as accurate wave propagation could not be achieved. The problem is how to manage of complex geology condition related with wave propagation in ground vibration control. Geological condition mapping with specific spatial range can and combine with Signature Hole Analysis be a solution to make wave propagation easier to accommodate in ground vibration control

Feb 1, 2020

By Dale S. Preece, Steven Knudsen

A discrete element computer program, DMC (Distinct Motion Code) was developed to simulate blast-induced rock motion. To simplify the complex task of entering material and explosive design parameters as well as bench configuration, a full-featured graphical interface has been developed. DMC is currently executed on both Sun SPARCstation 2 and Sun SPARCstation 10 platforms and routinely used to model bench and crater blasting problems.

Jan 1, 1994

By Dennis Dobson, Keith M. Henderson

Lone Star Industries, Inc. in Cape Girardeau, Missouri operates an open pit mine to produce limestone for its portland cement manufacturing plant. The present mining method, for safety and legal reasons, requires a set back from the property line, a berm, sloped overburden, and vertical rock walls with catch benches.

Jan 1, 1997

By George Pittman, Dan McCutchen

When an explosive manufacturer in the USA wants to put a new explosive formula or detonator design in the toughest proving ground in North American, it is Florida. Florida conditions have baffled many creditable blasting experts. This paper deals with some of the methods used to overcome these problems.

Jan 1, 1995

By J T. Patterson

The mining, quarrying and construction industries are often blamed for causing damage to residential-type structures when explosives are used. The claim experience for blasting vibration damage has been poor. This coverage is excluded from the Comprehensive General Liability (CGL) policy. To obtain this coverage, the policyholder must meet additional criteria and an additional premium must be paid. The risk management process offers the explosives user a technique for minimizing the risk of complaints and vibration damage claims on his insurance program and his cash flow. Case histories indicate that the vibration damage claims expense may be a lower risk than the risk of interference with production and cash flow. An annotated bibliography on risk management and defense of vibration damage claims is provided.

Jan 1, 1978