Search Documents

By Brian Hart, Rong Fan, Roger Smart, Andrea Gerson, Ning Xu

A complete strategy has been developed for identification of the reasons for losses in recovery and/or grade, due to changes or complications in mineralogy and in mineral surface conditioning, and their subsequent correction. The sequence of methods starts with comparison of mineral phases between QEMSCAN/MLA (compositional) and Rietveld XRD (crystalline diffraction) with bulk assay reconciliation. This methodology has recently led to identification of unrecognised amorphous content (12-40 wt.%), previously attributed to crystalline phases, in the fine fraction (<35 µm) of some problematic flotation feeds. Attached amorphous silica, talc- and chlorite-like fines have direct influence on the hydrophobic/ hydrophilic ratio on value mineral surfaces adversely affecting flotation. SEM/EDS is used in the backscattered imaging mode to determine possible problems with liberation (e.g. remnant local locking), not detected in standard liberation analysis, resulting in gangue flotation. EDTA extraction is used to assess bulk feed pre-oxidation and sequential oxidation product loading through the circuit. Changes in circuit solutions are assayed with speciation modelling of precipitates and potentially adsorbing species. ToF-SIMS with principal component analysis is then used to correlate surface species with specific minerals and can be used to assess the effectiveness of specific reagents particularly collectors. This approach identifies unwanted activating species and interference with value surfaces by adsorbed hydrophilic ions, precipitates and fine particles. When the interference or ineffective reagents are specifically identified, remedial action can be targeted. This method has identified residual talc-like layers (<10 nm thick) inducing gangue flotation of pyroxene and chromite in PGM flotation. Recent case studies of application of the full methodology to losses of molybdenite at KUCC and to sphalerite activation in the Cu/Pb circuit at Brunswick Mines with remedial action are discussed.

Jan 1, 2014

By J. Qiu

By means of natural sedimentation, two different bentonite samples from Shandong province were purified, this paper studies the Hydro-properties of the two purified montmorillonite samples. Firstly, the layer charge of two purified montmorillonite samples were calculated by crystal structure formula reckon method and general hydro-properties were also measured. The research results showed that the layer charge of montmorillonite correlated well with its hydro-properties: mont-morillonite with lower layer charge had better hydro-properties, such as Mont-1, which had higher swelling volume and gelling value with lower CEC; while, montmorillonite with higher layer charge had worse hydro-properties, such as Mont-2, which had lower swell volume and gelling value with higher CEC; it proves that the hydro-properties of montmorillonite depends on its layer charge characteristics, layer charge characteristic is the inherent factors deciding the hydro-properties of montmorillonite, montmorillonite with lower layer charge has better hydro-properties than the one with higher layer charge. In this paper, the relation between the medium condition and colloid performance of Mont-1 are also studied. The results show that the hydro-properties of Mont-1 could be changed by changing slurry concentration (w/w) and shear rate or adding certain amounts of inorganic cation electrolytes, dispersants and surfactants. The viscosity of montmorillonite slurry could be enhanced by increasing slurry concentration,adding univalentcation electrolytes (less than 4% w/w) or proper amounts of dispersants and surfactants (less than critical micelle concentration); The slurry viscosity could be reduced by decreasing slurry concentration, increasing shear rate, adding proper bivalent (more than 4% w/w) cation electrolytes or proper quantities of dispersants and surfactants (more than critical micelle concentration).

Jan 1, 2014

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin. The Rohm & Haas chelating resin, Amberlite IRC 748, with its weakly acidic groups, did not work in acidic solution but exhibited good results at pH 4 and above. The resin that efficiently removed metals from high acidic solutions was the bis-picolylamine resin. Maximum nickel uptake values ranged between 85 g and 112 g Ni per Kg of resin.The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to- solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment."

Jan 1, 2003

By K-O. Mickelsson, S. Töyrä, H. Esbensen

Accurate information of physical, chemical and metallurgical quality characteristics such as moisture content, iron grade and particle size are crucial for successful process control and for producing products within customer specifications. Correct moisture content of pellet feed is an important variable for successful balling of iron ore pellets and to minimize power consumption in the sintering process. Control of the filtering process in the pelletizing plant is therefore essential for both productivity and high product quality. The current measurement systems for moisture content at LKAB are based on two types of manual grab sampling, subsequently analyzed with rapid moisture determination methods. Previous studies of the measurement systems have indicated high sampling variability resulting in lowered possibilities for successful process control. The objective of the present study is to evaluate an alternative filter sampling approach and testing of on-line Infra-Red analysis (IR-analysis). On-line IR-analysis has the advantage of eliminating physical sample extraction and allowing for continuous monitoring of moisture content. However, this approach is sensitive to the surrounding environment, making careful calibration and control crucial for the quality of measurement results. Furthermore, as IR-sensors only target the surface of the conveyed pellet feed, several incorrect sampling errors need to be considered and counteracted to eliminate sampling bias and reduce the remaining measurement variability. Variographic characterization was applied to the two current grab sampling approaches of combined filtered material, to the alternative filter sampling method, and to the On-line IR-analysis. The results indicate that both the sampling of separate filters (using composite sampling and ISO-standardized moisture analysis), as well as a calibrated and well- maintained IR-sensor can improve the relative variability significantly, by lowering the total measurement system variance from 60% to 25%.

Jan 1, 2018

By F. v. d. Meer, G. Kretschmar, T. Mütze, T. Leißner

"Dynamic air classifiers separate particles in a gas flow due to different particle trajectories utilizing differences in the settling velocity of particles as characteristic property for separation. The present contribution takes a close look at the separation of heterogeneous mixtures, in which valuables and gangue minerals show significant differences in density. The focus was on a moist iron ore sample, which was characterized in terms of mineralogy, grain size distribution, and particle size distribution. The material was classified at a cut size of 45 µm and at feed moistures between 0 and 6 wt.-%. Additionally to standard characterization techniques, the moisture of both products was measured as well as the yield of fines as product fraction in a corresponding processing plant. In addition, an automated mineral liberation analysis (MLA) provided information of the enrichment and segregation of individual mineral phases in the products. The MLA of the classification products reveals a selective comminution of the mineral phases and especially on overmilling of the valuables. For the first time, the separation of individual mineral phases has been assessed and compared to the classic assessment of classification processes by means of particle size analyses. KEYWORDS Dynamic classifier, segregation, MLA, selective comminution INTRODUCTION Dynamic air classifiers separate particles in a gas flow due to the different trajectories of the particles. The result of such a separation process depends on the gas throughput of the classifier, the dimensions, design and rotational speed of the deflector wheel, as well as the state of dispersion and thus the geometry of as well as the turbulence and interparticle interactions in the separation zone. Air classification of moist feed materials can be divided into several sub-process (Leschonski, 1977; Mütze et al., 2016): - dosage of the feed material, - dispersing the solid feed material into a gas stream, - feeding the dispersed material into the classification zone by pneumatic conveying, - drying of moist particles during pneumatic conveying, - separation of coarse and fine particles, and - separation of fine particles from gas."

Jan 1, 2018

By Yessengaziyev Azamat, Almagul Ultarakova, Onayev Murat, Barkytova Botakoz

"The research is aimed at solving the processing of waste products of titanium-magnesium production. The aim of the research is to extract synthetic carnallite and industrial products enriched with niobium from waste products of titanium-magnesium production. Analysis of the current state of the titanium and magnesium production in the Republic of Kazakhstan shows the availability of significant amounts of chloride wastes containing valuable components. Magnesium and potassium with an average content of 50-60 % potassium chlorides, 25-30 % magnesium chlorides are lost in the wastes of the titanium and magnesium production. Ust-Kamenogorsk Titanium Magnesium Plant JSC (UKTMP) currently imports carnallite that is a KCl-MgCl2X6H2O binary salt at quite high prices. Chloride wastes of titanium production, sublimates of dust chambers of a titanium chlorinator, sludge of a magnesium electrolytic unit and sludge of a carnallite chlorinator has been chosen as the targets of our research. The analysis of niobium distribution within any solid waste of a titanium slag chlorination process in UKTMP JSC showed that the highest content of niobium is in the sublimates of dust chambers of a titanium chlorinator in the ranges from 0.26 to 1.0 %. Among the niobium extraction technologies considered, the known method of its extraction from the chloride waste is leaching with weak solutions of mineral acids or alkalis in order to convert the chloride salts into the solution to be used for synthetic carnallite extraction. Besides niobium, other impurity components are transferred to the cake and shall be separated from the base metals. The effective method for this is the chlorination process enabling niobium transfer into the sublimates in the form of chlorides and thus separating it from the majority of the impurities. The condensed niobium chlorides are hydrolyzed transferring it into sediments in the form of oxide. New ways of processing waste products of titanium-magnesium production with the receipt of marketable products are relevant in the development of processing of mineral raw materials."

Jan 1, 2018

By G. K. Nimal Subasinghe

The establishment of grind size that optimally liberates the valuable mineral for efficient down-stream processing is of great importance for most mineral processing operations. Reasonably accurate comminution models as well as models of downstream separation processes may be found in the literature but their use in optimizing grind size is limited without an associated liberation model. In this work, an attempt has been made to address the above shortcoming by demonstrating how the effective parameters of the downstream flotation process may be predicted from the liberation characteristics based on the ore texture data for a disseminated nickel ore. In this regard, the liberation model based on linear intercept distributions of mineral and gangue proposed by King (1979) and its application to predict the flotation performance of an industrial plant demonstrated by Schaap (1979) may be considered useful contributions. However, while the model proposed by Schaap is simplistic enough, it is based on several assumptions due to the non-availability of intercept length measurements on the parent rock, in particular, on the extent of mineral exposure on the surface of comminuted particles. In this work, the linear mineral and gangue intercepts on polished specimens of a binary ore, comprising darker pentlandite as the valuable mineral and lighter barren host rock were measured using an image analyser. The resulting intercept distributions followed negative exponential distributions. Using the mean sizes of mineral and gangue intercepts, the proportion of liberated, compo-site and mineral occluded particles of a given size, the extent of mineral exposure on the surface of particles and their mean mineral contents were calculated using principles of renewal theory. The rock was then crushed and ground and different size fractions were floated. It has been shown that the parameters of observed recovery data based on 1st order kinetics such as the associated rate constant and ultimate recovery agrees well with those predicted from the quantities calculated above. This work has important practical implications since it can indicate variations in flotation performance arising from changes in mineralization within a large ore body.

Jan 1, 2014

By H. R. Manouchehri

"In mining and minerals industry, except profitability, there are some crucial factors that represent components in economic machinery of a mine and related activities. These are sustainability and minimizing environmental impact factor. Environmental concerns combined with the water and energy availability and related costs, as well as public license to operate all contrive to demand for more efforts targeting sustainability. Mining industry is highly energy-intensive (estimated to consume 6-7% of total world’s energy), with varying the energy efficiency across the industry resulting in significant costs. Size reduction is the main energy consumer contributing to almost 50% of the total energy used in mining. That means efforts must be made to introduce energy efficient comminution flow-sheets and machineries for sustainable development. Since the crushers are more energy efficient than mills, it is logic to push down-sizing in crushing stage(s) as far as technically possible. That has been strategy for Sandvik Mining and Rock Technology in supplying advanced and effective crushers to provide fine crushed product for subsequent milling stage. Lowering the energy consumption and related costs as well as increasing throughput have been the main objectives in design and development of comminution circuits and related machineries. Inefficiency in comminution technology, particularly in grinding, has long been regarded as a major area for investigation and development, especially when production of fines and ultra-fines are considered. In an attempt to explore the potential of fine crushing and its effects on subsequent milling process the fine crushing performance of Sandvik’s conventional cone crusher and Vertical Shaft Impactor (VSI) in pilot scale to define the energy consumption and circulating load in fine crushing. Tests were conducted to obtain fine crushed products at P = 2 mm in a close circuit. Furthermore, the crushed products were characterized and compared by grind-ability, morphology, and surface area measurement tests. Finally, the energy consumption to grind the crushed products to specific grind size was calculated."

Jan 1, 2018

By Sravya Kosaraju, Christian Ekberg, Stefan Allard

Li-ion batteries are now used in electric vehicles (EVs), plug-in hybrid vehicles (PHEVs) and, hybrid electric vehicles (HEVs). Nanostructured Li(NiyMnzCo1-y-z)O2 is one of the more popular cathode chemistries for automotive Li-ion battery, due to its enhanced properties such as large surface area, short diffusion length, enhanced ionic and electronic conductivity, improved mechanical strength and structural integrity [Pan et al, 2013]. Recycling of Li-ion batteries helps to mitigate environmental effects of virgin metal extractions along with improper disposal of end of life batteries. To fulfill these objectives of the recycling, recovery of pure streams of the involved metals should be considered. In this study, the batteries were first discharged and dismantled in an inert atmosphere (Ar). The electrodes were then heat treated in a box furnace. This was done in order to break the chains of the adhesive (PVDF) and consequently separate the metallic substrates Cu and Al from the electrochemically active compound. This heat-treatment also helped to simplify the dissolution of the metal constituents in the electrochemically active compound from the cathode in the acid leaching process. Solvent extraction was chosen to achieve separation and recovery of metals with higher purity from these leachates. In the scope of the present work, a complete process from the point of dismantling to separation of constituent metals using solvent extraction was studied.

Jan 1, 2014

By S. M. H. Haddad, M. Saghaeian, R. Hejazi

"Due to limited water resources in mineral processing plants, increasing the efficiency of iron tailing dewatering system in order to obtain more usable water is very important. In this research, flocculation process, as one of the best method for water recovery, was investigated by using one organic cationic and three anionic types of flocculants with different dosages (10, 20, 30 g/ton) and iron ore tailing slurry (8 % w/w solidity) in series of graduated cylinders and obtained results were compared. it is observed that for tailing sample, the anionic flocculants have a significant effect on the settling rate of solid particles compared to the cationic types. Furthermore, effects of temperature (10, 23 and 43 ºC) and pH (2, 7 and 12) on the rate of settlement and turbidity was studied by utilizing the best flocculant. Findings showed that by increasing the amount of flocculant dosage, sedimentation rate went up and turbidity decreased. Comparison the out-put data of tests indicated that at temperature 23 °C and pH=7, the best results for both of faster settling rate and producing more clear water were reached. It should be considered that lower temperature has a more negative effect on the sedimentation rate and overflow water quality. So it will be predicted that for cold seasons, the consumption of the flocculant powder would be higher than the moderate or warm seasons. Also, coagulation/flocculation was evaluated by applying organic cationic coagulant added to anionic flocculant in three different times. Different ratios of coagulant to flocculant was examined (70%:30%, 50%:50%, 30%:70%) as well. Overall, utilizing coagulant had desirable influence on sedimentation experiments and obtaining high quality water. 1- INTRODUCTION In mineral Factories, among the important processes, solid-liquid separation process due to limited resources of water is very important and operates on iron ore tailing in settling tank as thickener in order to gain clear water for preventing water loss and applying again in plant units (Ciftci and Serhat Isik, 2017). Iron ore tailing include inharmonious compounds of iron oxides, silicates and aluminum-silicates. The percentage of solid in the tailing usually changes between 5 and 10 percent (Dash et al., 2011). One of the major problem about dewatering of tailing in thickener is solid-liquid separation of slurries with high stability because of fine particles. It means that rate of sedimentation is very slow and recovered water quality is inappropriate. This issue can be solved to a large extent by factors such as pH control, ionic strength and flocculation/coagulation process which results in aggregation of particles so that settlement by gravity is happened (Dash et al., 2011)."

Jan 1, 2018

By A. D. Bas

Copper minerals present difficulties during the cyanide leaching of gold ores leading to excessively high consumption of cyanide (and oxygen) coupled with low extraction of gold. Copper cyanide species, if present at high levels, adversely affects the downstream processes such as the activated carbon adsorption and the effluent treatment. In this study, the extraction of gold from a copper-bearing gold ore by ammoniacal cyanide leaching was studied. Furthermore, ammonia leaching as a pretreatment process ahead of cyanide leaching was also examined. Only ~12% of gold was extracted by direct cyanide leaching of the ore. The addition of lead nitrate did not affect the leaching of gold. When ammoniacal cyanide leaching system was used, the extraction of gold was significantly improved to >90%. Similarly, the pretreatment of the ore by ammonia leaching was shown to lead to high gold extractions (98%), in subsequent cyanide leaching with significant reductions in the consumption of cyanide. This appeared to be linked with the ready dissolution/removal of copper during ammonia leaching.

Sep 1, 2012

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By K. C. Corin, M. S. Manono, J. G. Wiese

"It has been suggested that hydroxo species, particularly those of calcium, selectively adsorb onto gangue minerals. Such species enhance the depressive action of carboxymethyl cellulose (CMC) onto gangue via an acid-base interaction between the positively charged mineral surface and the negatively charged CMC molecule. Thus, the hydrophilicity of gangue minerals is enhanced, preventing the dilution of the concentrate. However, as there is little evidence to support these claims it is important to investigate. Adsorption data and mineral surface charge analyses will allow a fundamental understanding into how electrolytes and their ionic strengths affect gangue-depressant adsorption. It is strongly anticipated that decoupling these effects will allow process operators to tailor their process water quality needs towards best flotation operating regimes and in the long run effect closed water circuits. Thus, using talc and pyrrhotite as proxies, this work investigates the influence of the ionic strength of process water on the adsorption of CMC onto minerals in sulphide flotation.INTRODUCTIONThe phenomenon of gangue depression in mineral flotation is of critical importance as regards the attainment of a required concentrate grade. This thus suggests that the depressant of choice has to have a highly selective affinity for the targeted gangue minerals. This would ensure the necessary prevention of gangue from reporting to the concentrate without inadvertently depressing the value bearing mineral. The chemistry of the environment regulates the manner in which gangue depression occurs. In sulphide flotation, polysaccharides are used as depressants of choice to depress naturally floatable gangue which may in the case of Merensky ores exist as talc. The two widely used polysaccharides in the South African context are carboxymethyl cellulose (CMC) and modified guar gum. It is suggested that polysaccharides depress gangue by rendering the surface of gangue hydrophilic or by preventing the formation of hydrophobic layers on gangue mineral surface, forming large gangue aggregates and thereby increasing their heterocoagulative nature (Shortridge et al., 1999)."

Jan 1, 2018

By A. Kogelbauer, A. Stadtschnitzer, A. Boehm, F. Schillab

"The paper covers the design and implementation of an industrial dense medium cyclone plant for carbonaceous iron ore, the proving of efficiency as well as the development of a predictive model for plant control. The VA Erzberg GmbH mines about 12 Mio.t of carbonaceous rock ore at the “Steirische Erzberg”. Due to increased demand of the Austrian steel plants, the production of ore concentrate was raised by 30 % up to 3.0 Mio t/a during the last 5 years. One of the projects to realize the increase in capacity at improved concentrate quality was the implementation of a dense medium cyclone plant for the fine size fraction – 8 +1 mm replacing the former dry permanent magnetic drum separators. By physical separation the siderite variety “spateisenstein” (42% Fe) of a density of 3,8 g/cm³ is separated from ankerite (10 – 17% Fe), the second iron bearing carbonate with a density of 3,2 g/cm³, dolomite, calcite and silicate bearing schists. The feasibility of the process was proven by the test results obtained from a test rig, that was constructed and operated in close cooperation between the Chair of Mineral Processing, Montanuniversitaet Leoben and VA Erzberg GmbH. The density separation surpassed the efficiency of magnetic separation clearly shown by •- values. The plant performance tests (capacity 120 t/h) verify the cut densities defined by Tromp T50 -values and the assigned efficiency found in the pilot tests at varied settings of media density, pressure drop, cone angle and apex diameter. The test rig as well as the final process will be presented. In order to create a tool to predict the performance of the DMS in the centrifugal field at various settings for varying feed composition the experimental results from size and density testing are analyzed in a modified way to obtain physically justified, smooth approximations for the performance curves. Models developed on coal washing plants are checked for their validity at increased densities."

Jan 1, 2018

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

By T. Lang

Clay sorbents from the North Bohemian Brown Coal Basin represent important but still some-what neglected accessory raw material. Submitted paper is concerned with relation between mineral structure, sorptive efficiency and reclamation exploitation of these rocks. Characters and localities of main clay sorbents from the North Bohemian Brown Coal Basin are shortly evaluated in an introduction. In next part, methodology of mineralogy survey for these accessory raw materials is stated, it is based on diffract analyse with D 5000 Siemens X-ray diffracto-meter. At the conclusion results are stated of mineralogy analyses from several clay sorbents. The determination of the zeolite and montmorillonite localities was accentuated. The paper presents also possibilities of practical clay sorbents utilization, especially by reclamation works.

Jan 1, 2014

By Venkataramana Runkana, Pradip Gautham, Beena Rai, Sreedhar Reddy

"IT enabled platforms are the key to provide an integrated view of the business activity or an enterprise as a whole. Attempts to integrate all functions in an enterprise such as mine-to-market initiatives, wherever and to whatever extent implemented, have provided significant benefits to the industry. The transformative potential of IT enabled integration platforms is illustrated in this communication from our own work in this field. TCS PREMAP (Platform for the Realization of Materials and Products) is a knowledge-driven engineering design and development platform which leverages modeling and simulation and artificial intelligence into the engineering design process. We illustrate the customization of this generic platform for the design and optimization of mineral processing plants in an integrated manner. TCS PEACOCK (Process and Equipment Analytics for Optimization and Control) has been developed to enable automation of data analytics in the operating plants. We illustrate its utility and power in improving the plant performance with the help of case studies from our work on pelletization of iron ores and optimization of flotation plants. INTRODUCTION We are living in an exciting digital era. With the advent of cloud computing and social media on the one hand and rapid advances being made in several research areas of interest to us in the minerals and metals industry such as artificial intelligence (AI) & machine learning, robotics, unmanned vehicles including drones, big data analytics, 3D printing, sensor technologies, renewable energies and internet of things (IoT), many disruptive transformations in our industry are on the horizon. Recent advances in information technology (IT) and knowledge engineering, in combination with appropriate domain expertise, that is, our enhanced understanding of the underlying science of mining and mineral processing operations and the availability of a variety of powerful modeling-simulation tools make it possible to address the challenging problems facing the mining and mineral processing industry, in an integrated manner."

Jan 1, 2018

By Jim Pae Lem

This study investigates the mode of occurrence of uranium in a copper concentrate from the Prominent Hill mine. Mineralogical and liberation studies of a high grade Cu concentrate (monthly composite) containing uranium (U) were undertaken using QEM-Scan in combination with QXRD and ICP-MS. The study aimed at determining in what form U was recovered, and by which mechanisms. The deportment of U was studied in 3 size fractions; +20µm, -20+8µm and -8µm. QEM-Scan analysis showed that uranium was present as U(Cu)-silicates, U-silicates, UPbOx/FeOx or traces of UThOx and UTiOx, with the U-silicates present across the size fractions. The association of uranium bearing minerals with copper sulphides varied across the size ranges. Interestingly, most of the U (46% by weight) was distributed in the finest fraction (-8µm), in which the deportment of Cu was low (6%). Over 40% of the U mineralisation in the -8µm was liberated. In terms of the floatation response, while recovery of the uranium minerals as a result of their association with copper sulphides (as composite particles) was evident, recovery of UPbOx locked in hydrophilic haematite in the +20µm size fraction suggests, that other mechanisms (e.g. Inadvertent activation by Pb from radioactive U decay) are possible. Furthermore, the high amount of fine liberated U bearing particles in the concentrate points at entrainment as another major mechanism for uranium recovery, and therefore, a target for process optimisation.

Sep 1, 2012