Search Documents

By Derek Caizergues, Hurman Eric

Experiments have been conducted at around 1700°C to determine the possibility of carbothermic reduction of alumina under the presence of a metallic solvent. Total pressure of the system was reduced to around 30kPa and metallic nickel, iron, copper and tin were selected as the solvent. The highest recovery of aluminium was achieved with the nickel solvent followed by iron, copper and tin. This ranking for the first three was also in accord with the extent of negative deviation form ideality in the respective binary solutions of these solvents with aluminium. The tin-aluminium system displays positive deviation form ideality. The rate and extent of reduction was found to be highly dependent on temperature and pressure. The pseudo first order reaction rate was found to be applicable to the process in all the solvents used. Rate constants were calculated and it is also suggested that the reduction was controlled primarily by the chemical reaction rate.

Jan 1, 2003

By Kyle Bartholomew, Robert McIvor

"Functional performance analysis of closed circuit grinding provides valuable insight into the two components of ball mill circuit grinding efficiency: classification system efficiency and mill grinding efficiency. Classification system efficiency isolates the combined effect of classifier performance and circulating load ratio from other circuit variables, such as ore grindability and the mill grinding environment. Optimization of classification system efficiency ensures grinding energy is applied to particles needing further size reduction and not to overgrinding. Entirely based on size distribution data, classification system efficiency precisely distinguishes subtle changes in classification system performance. Use of the functional performance equation to isolate mill grinding efficiency allows for proper optimization of the mill grinding environment by isolating confounding effects of changes in classification and ore grindability. Variables such as mill percent solids and grinding media selection can be optimized using the mill grinding efficiency subcomponent of functional performance. First published by McIvor in 1988, the functional performance equation provides a set of standardized, quantitative optimization criteria, simple and powerful, which link circuit performance to plant design and operating variables that can be manipulated. Functional performance optimization has been applied in numerous mineral processing plants globally and continues to gain acceptance as a practical means for grinding circuit optimization. In this paper, examples of derivation and industrial application demonstrate the means by which functional performance analysis dissects grinding circuit efficiency into its subcomponents allowing the reader to apply this straightforward, powerful optimization methodology at their mineral processing operation."

Jan 1, 2014

By H. Koca, D. O. Aksoy, S. Koca

"In this work, modelling of galena flotation from a disseminated Pb-Zn ore containing 0,83 % Pb was investigated. In the flotation experiments, collector type and amount, frother type and amount, particle size, pH and flotation time were kept constant while solid ratio and depressant dosage were varied. The varied parameters are described with a mathematical model by using statistical design method. Central Composite Design method which is one of the principle response surface methodologies was used in statistical design and analysis of experimental results and process modelling. Two quadratic mathematical models were developed for Pb grade and Pb recovery. Analysis of variance showed that models obtained for Pb grade and Pb recovery were found to be statistically significant in 95 % confidence level. Predicted vs actual values of Pb grade and Pb recovery were also given in graphically. It was found that predicted values represent approximately 96 % and 94 % of actual Pb grade and Pb recovery, respectively. The high values of R-square (R2) indicate that the models developed for two response variables are powerful. INTRODUCTION Lead and zinc metals are widely used in electrical, mechanical, military, metallurgical, chemical, light and medical industries. Sulfide ores are the main resources for lead and zinc minerals (Luo et al., 2016). Froth flotation is the main beneficiation method to achieve lead and zinc sulfide minerals separation. There are two basic approaches to obtain lead and zinc separation by flotation. First, flotation of lead sulphide is carried out and zinc sulphide and gangue minerals are depressed by various depressants and second, the bulk flotation of lead and zinc sulphide is carried out to obtain a concentrate of lead and zinc, followed by the lead and zinc separation. (Yuan et al., 2012). Apart from concentration of lead and zinc by flotation, there are a few literature that reports concentrations of lead and zinc by gravity and hydrometallurgical methods with remarkable success (Goktepe, 2005; Yanbo et al., 2016)."

Jan 1, 2018

By Z. K. Liu

Production of the amines collectors and cation surfactant gives out the liquid waste containing high COD (Chemical Oxygen Demand) and ammonium & nitrogen, which is difficult to be treated with conventional biological method to reach waste water discharge standard. In this paper an engineering practice of treatment on the liquid waste by the technology combined high effective microbe with A/O (Anaerobic& aerobic) process is presented. The quality of treated water comes up to class A national standard for discharging.

Jan 1, 2014

By Gjergj Dodbiba, Toyohisa Fujita, Li Pang Wang, Masashi Yamane

"The platinum-group metals (PGMs), are currently receiving worldwide attention as they have major industrial uses. PGMs, i.e. ruthenium (Ru), rhodium (Rh), palladium (Pd), osmium (Os), iridium (Ir), and platinum (Pt), are widely used as catalysts in petroleum and chemical processes. In addition, they find wide applications in automotive exhaust-gas control converters and are of immense importance to the electronic industry. Broadly speaking, PGMs are extracted in minute quantities from a limited number of ores, found mainly in South Africa and Russia. As the PGMs are both costly and almost indestructible, they are usually recycled from various forms of scrap. In other words, the recycling of the PGMs is an essential factor in the overall management of the PGM economy. In addition, the ever-increasing user areas have created renewed interest in the search for new sources or deposits of PGM, which in turn requires an in-depth knowledge of its characteristics. In this work, the emphasis is placed on the need to analyze the composition and microstructure of blast-furnace slag for recovering PGM metals. In other words, chemical composition, surface analysis and microstructure analysis of the DC arc furnace slag have been carries out. The aim is to provide a detailed analysis of this material for anyone with an interest in gaining further knowledge of its specific content for recovering PGMs."

Jan 1, 2014

By M. Canbazoglu

In this study, optimum sulphuric acid leaching parameters of zinc and other valuable metals from two different waelz clinker samples were researched. Origins of the samples are electric arc furnace dust and original non-sulphite zinc ore waelz clinkers. The main zinc mineral determined as zincite in these samples. Collective dissolution of zinc and other valuable metals in waelz clinkers can easily achieved by sulphuric acid leaching of them. 96% of zinc can be dissolved at 80 ºC, 60 g/L sulphuric acid concentration, 60 min. leaching time and 1/5 solid/liquid ratio. Almost 90% of Cd, Cu and Co in clinker dissolved at these conditions while dissolution of Fe was almost 20%. The consumed acid amount for dissolved per ton of zinc is approximately 1.7 tons at these conditions.

Jan 1, 2014

By Y. M. Zhu

Lead in environment often causes a serious health hazard. The removal of Pb2+ from aqueous phase is a beneficial project. In this paper, deposited Saccharomyces cerevisiae (S.c.) was chosen as adsorbent, Pb2+ ions as adsorbate, and the process of biosorption was studied. The dynamics of the adsorption was investigated. The adsorption mechanism of Pb2+ by S.c. cells was also investigated by detecting microstructure, zeta potential under different pH value, FT-IR spectra of the S.c. particles before and after biosorption. It was shown that the biosorption of Pb2+ by deposited S. c. is a rapid process, and the adsorbing equilibrium is reached within 10 minutes. The Zero point of zeta potential of S.c. cells is pH=3.3. When 2.0<pH<3.3, there exists biosorption (biosorption rate 76%~88%), which means static bio-sorption been not the only kind of biosorption. FT-IR spectrum analysis showed that groups on bacteria surface were mainly characteristic groups of protein and amylase; oxo-groups and nitric-groups on S.c. cell surface could chelate with heavy metal ions. Chemical adsorption might exist in the process.

Jan 1, 2014

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By Viswanathan N. Nurni

In metallurgical processes, more and more usage of hydrocarbons is encouragedto bring down the carbon emissions. In this regard, numerous investigations onreduction of oxides by C-O-H-N gas mixture have been reported. Attempts to simulatethese reduction processes using shrinking core model, one of the commonmodels used for such studies, have under predicted the reduction rates. This maybe owing to the fact that the homogeneous reaction in the gas phase is not being considered. If the reaction temperatures are above 1000K, generally so for manyreduction processes, the homogeneous gas reaction rates are expected to be sohigh that one can assume local equilibrium in the gas phase. In the present study,reduction of wustite in a C-O-H-N gas mixture has been modeled using shrinkingcore model considering the water gas shift equilibrium in the gas while it diffusesthrough the product layer.

Sep 1, 2012

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By T. C. Sun

Two wasted activated sludges (WAS), from an industrial wastewater treatment and a sewage treatment plant respectively, and 7 collectors are used to investigate the feasibility of air flotation thickening of WAS by adding the collectors used in mineral processing. The collectors experimented include straight chain fat acids with different chain length, sodium oleate, alkyl sodium sulphonate, sodium dedecylsulfonate, and dodecylamine. The results show that the thickening efficiency varied depending on different collectors. Of the collectors experimented, dodecanoic acid and dodecylamine are best collector for thickening both sludges.

Jan 1, 2014

By T. Ueda, T. Oki, S. Koyanaka

"Accurate assessment of the liberation state of crushed ore particles is important for efficient mineral processing. In general, the liberation state is assessed by two-dimensional (2D) measurement of polished ore sample sections. However, this 2D measurement inevitably suffers from overestimation of the degree of liberation, known as stereological bias. This arises from the fact that biphase particle sections of which only one phase happens to have been cut are indistinguishable from liberated particles. To date, several stereological correction methods have been proposed, but their applicability for various types of particles has not yet been sufficiently examined, and this tends to undermine their practicality. We have addressed this problem using a numerical-analytical approach in which various types of biphase particles are modeled, and the 2D sectional information is compared with actual three-dimensional (3D) information. Through simulations, we revealed a general relationship between the internal mineral structure of particles and the stereological bias. Finally, we have developed a unique stereological correction method in which the texture (a 2D pattern characteristic) of particle sections is used to estimate the internal structure of particles, and thereby the stereological bias. KEYWORDS Mineral liberation, stereological bias, texture analysis INTRODUCTION Mineral liberation assessment of 2D particle sections inevitably suffers from stereological bias; that is, overestimation of the degree of liberation. Stereological bias is caused by the fact that a composite particle can be misidentified as a liberated particle when only one phase happens to have been cut in sectional measurement. Stereological bias has attracted attention since Gaudin pointed out its importance in 1939 (Gaudin, 1939). Several attempts have been made to measure the 3D liberation state directly, avoiding the bias, using X-ray computed tomography (Gay and Morrison, 2006; Lin and Miller, 1996; Miller et al., 2003; Miller et al., 2009; Reyes et al., 2017; Videla et al., 2007). These have provided useful information through laboratory testing, but further technical refinement is necessary for practical usage, to overcome the technique’s limitations in terms of resolution, assessment of minerals of similar density, and speed. Therefore, for practical purposes, detailed information regarding mineral phase geometry is obtained by sectional analysis, using automated scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX)-based analysis (e.g., with a mineral liberation analyzer (MLA) (Fandrich et al., 2007; Sandmann, 2015)); and the development of an effective method of stereological correction, which predicts the relevant bias and transforms the measurable 2D degree of liberation into its 3D counterpart, is an important research aim."

Jan 1, 2018

By M. M. Fan

In Florida?s phosphate industrial practice, the most favorable upper size limit of froth flotation is 1.18 mm which corresponds to particle weight of about 2.8 mg. Conventional froth flotation is not efficient in upgrading coarse particles (+0.425-1.18 mm). A limited number of studies have been devoted to understanding and improving coarse particle flotation. We have shown that the coarse particle flotation performance can be significantly improved by the presence of picobubbles generated by hydrodynamic cavitation. In this study, the size of picobubbles produced under certain hydrodynamic conditions was measured by a laser particle size analyzer. A size-by-size flotation performance analysis of coarse phosphate froth flotation in the presence of picobubbles is conducted in terms of flotation kinetics, selectivity and recovery. It was found that picobubbles doubled the flota-tion rate, increased the P2O5 recovery more significantly for +0.85-1.18 mm particles than +0.425- 0.6 mm and +0.60-0.85 mm particles. At a given acid insolubles (A.I.) rejection, the presence of picobubbles increased the P2O5 recovery by up to about 25%.

Jan 1, 2014

By Bern Klein, Givemore Sakuhuni, Libin Tong

The use of continuous discharge centrifugal concentrators introduced in the early 1990’s for recovery of gold associated with sulphides has introduced a novel application niche for gravity concentration which could not be realized with the low mass yield batch and semi-continuous concentrators. A typical application is scavenging gold associated with sulphides from flotation tails which has potential to increase productivity by reducing gold loss to tailings and lower grinding cost by using a coarser grind. However, the full potential of this technology has not been fully exploited partly due to the lack of reliable small sample procedures to demonstrate applicability. This paper introduces a bench-scale procedure developed to characterize the Knelson Continuous Variable Discharge concentrator (CVD) for scavenging gold from flotation tails. The procedure code named gravity release analysis was derived from standard flotation release analysis. It is a modification of the gravity recoverable gold and gravity amenability test in order to best simulate continuous centrifugal concentration. Based on this iterative procedure, a gravity release index similar to the flotation rate constant, for measuring individual mineral gravity susceptibility for an ore is introduced which can be a useful quantitative measure to both predict application of centrifugal concentration and for plant design. The gravity release analysis procedure was tested on a polymetallic flotation plant tailing at Myra Falls, BC, Canada and results show that it can predict CVD performance. The gravity release index for gold was observed to decrease with each successive cleaner stage showing that the initial stages recover liberated gold whilst successive runs recover gold associated with sulphides and or gangue. The difference in magnitude of the gravity release index for different mineral species shows the species separable by centrifugal concentration.

Jan 1, 2014

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

Spent automobile catalyst is an important secondary resource of PGMs (platinum group metals) and the recovery is significant. Various methods of recovery technology have been reported and applied in practical production, including pyro- and hydrometallurgical processes. Since the grade of PGMs in the catalysts is so low, approximately 0.5 wt. %, the present recycling technologies require high energy-consumption, it is of great significance to enrich the PGMs with some energy saving physical separation methods as a pretreatment. Automobile catalyst is usually composed of cordierite phase as a substrate and alumina phase, with PGMs, which covers the cordierite phase. We adopted the quenching pretreatment, one method of thermal shock, to generate micro-cracks between the two phases and separate the alumina phase from cordierite. Quenching was carried out by heating the catalysts in an electric furnace of different temperatures followed by rapid soaking into cold water. It was found that the phase boundary between alumina and cordierite was broken in the quenching and selective separation (detachment) of alumina from the cordierite could be achieved in the following surface grinding. The effect of quenching was checked by microscopic observation, hardness measurement, and chemical analysis. This paper figures out the stress formula of the quenching process, which is largely connected with layer thickness and temperature gradient by using an FEM (Finite Element Method) simulation and clarifies the mechanism of crack generation in the quenching process. Keywords: automobile catalyst, PGM, quenching process, FEM

Sep 1, 2012

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003