Search Documents

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Kessi E. Zicko, Eric A. Hackenberg, Paul J. Lewis

"Following snow melt and spring rains in 2011, a landslide measuring approximately 600 feet long and 300 feet in slope length occurred within the southbound roadway embankment of a heavily travelled 2-lane divided highway in North Central Pennsylvania. Driven steel piles were designed to stabilize the embankment slope. Factors affecting the selected stabilization technique included an adjacent reservoir, wetlands, the length and depth of the failure plane, extent of glacial lake deposits, excess pore pressures in the foundation soils, and an area of archaeological interest. Field reconnaissance and subsurface explorations including borings, instrumentation, geophysics, and laboratory testing indicated that glacial lake deposits were present in the toe region of the embankment. Instrumentation proved key in measuring excess pore pressures and in locating the failure plane, and geophysics was utilized to estimate the extent of the soft glacial lake deposits and to estimate pile lengths. The existing condition of the embankment was modeled in computer slope stability analyses, which were also used to help assign soil parameters. Significant costs were associated with constructing a berm due to the impacts on adjacent site features. Therefore, multiple rows of driven steel H-piles were designed for installation along the toe of the embankment. The design lateral load in the piles was based on slope stability analyses, and the pile size and number of piles were based on lateral pile computations with modified p-y curves to account for installing piles in an active landslide. The relationship between the factors of safety from slope stability and the LRFD pile design was significant in determining pile loads for lateral analyses.INTRODUCTIONA landslide developed along the lower portion of the southbound embankment of State Route 15 in Tioga County, Pennsylvania. The road passes through a steep valley and is located along the southern extent of the Tioga Reservoir. Although no damage to S.R. 15 was attributed to this landslide, the close proximity of the slide to the road posed a concern for the long-term stability of this section of roadway.This paper presents a summary of the site history; the subsurface conditions based on borings, instrumentation, a geophysical survey, and laboratory testing; slope stability analyses including alternatives assessment; and the pile design.SITE HISTORYS.R. 15 was originally located in the valley along the Tioga River and traversed through the towns of Tioga and Mansfield. Although the reason is unknown, it is interesting to note that Old S.R. 15 curved away from the river in the area of the landslide. In the mid 1970’s, S.R. 15 was relocated to the eastern hillside prior to construction of the Tioga-Hammond Reservoir by the U.S. Army Corps of Engineers. The relocated highway was constructed in stages. Two lanes of relocated S.R. 15 were initially constructed to carry one lane of northbound and one lane of southbound traffic. At this same time, the majority of the fill was placed for two future lanes immediately to the west, which would eventually allow for two lanes in each direction. The two eastern lanes would then carry northbound traffic after completion of the two southbound lanes to the west."

Jan 1, 2015

By Prakash Annamalai Rangasamy, Muthukkumaran Kasinathan

"Infrastructure development like elevated expressways, metro train and flyover are required proper foundation system to carry heavy traffic loads/significant lateral load, especially in the presence of hard stratum at shallow depth. Pile foundation under bridge pier system is widely adopted in metro projects where the piles are essentially socketed in rock. However, the drilling in hard rock is a time consuming process and needs heavy machineries which lead to delay in construction activities. In the present study, the influence of free standing height on rock socketing under lateral load is investigated. The experiments were conducted on an instrumented model pile with varying depth of socketing and for varying Lf/D ratios. The experimental results shows the load carrying capacity of the pile increases by increase in Lf/D ratio, where in the case pile without socketing (bearing on rock) is compared with 3D depth of socketing. Thus socketing the pile provides significant benefits on carrying capacity of lateral loads. Embedding the pile into hard strata reduces the lateral displacements substantially compared with pile bearing over hard strata. Form the study, it is noticed that the influence of rock socketing has significant effect in the lateral load capacity. And also, the effect of free sanding height play a major role in the lateral load capacity of the rock socketed piles.1. INTRODUCTIONA substructure carrying heavy lateral load at shallow depth, the structure has to be socketed into hard strata to enhance the efficiency of load carrying capacity. The existing field practice is to socket the end bearing piles in hard strata over a minimum depth of four times the diameter of the pile based on rock classification (IS 14593:1998). Reese (1997) developed p-y curves for analysing drilled shafts in rock under lateral loading, based on strong and weak rock criteria. The proposed p-y curve approach has the ability to simulate the nonlinearity and non-homogeneity of the rock mass surrounding the drilled shaft. Gabr et al. (2002) proposed a hyperbolic p-y criterion based on field tests on small diameter drilled socketed shafts. By considering pile as linearly elastic semi-infinite space and soil as homogeneous isotropic material, Poulos (1971) proposed solution to determine the horizontal displacement and pile head rotation. Poulos (1972) extended this elastic continuum approach to give an approximate solution by considering drilled shaft and pile bearing on rock as fixed and pinned end boundary condition. Zhang et al. (2000) developed a non-linear continuum approach for drilled shafts in a soil and rock mass by considering the effect of soil and/or rock mass yielding on the behaviour of shafts. Randolph (1981) conducted a parametric study on the response of laterally loaded piles embedded in an elastic soil continuum. The study was conducted using the finite element method and the results were fitted with closed-form expressions from which the lateral responses of piles were calculated. The solutions given by Randolph (1981) were expanded by Carter and Kulhawy (1992) from the results of finite element studies on the behaviour of laterally loaded flexible and rigid drilled shafts in rock. Desai and Christian (1977) gave a finite difference program to solve rock socketed problems by considering soil and rock mass as elastic-perfectly plastic. Zhang et al. (2000) verified the proposed finite difference method with existing field test results. Gabr et al. (2002) and Liang and Yang (2006) proposed hyperbolic p-y curves based on filed test results and verified with finite element programs. However the need of field and lab scale experimental studies to validate the existing methods of analysis is necessary."

Jan 1, 2015

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) method as the representative deep mixing technique has been demonstrating best practice on ground mitigation works coping with complicated soil condition and limited site space. This technique plays an important role in many projects to stabilize soft ground involving troubles like sliding failure, settlement, bearing capacity etc. Serious disasters caused larger earthquakes make great demand on the application of deep soil mixing these days. Special design and alignment of deep soil mixing has been established against to liquefaction and serious failure due to liquefaction. In this paper, representative example of liquefaction mitigation by DJM method is summarized. The paper also present result of surveillance of sites installed DJM col umns after attack by Tohoku Pacific Ocean Earthquake. Performance of DJM columns suffered the earthquake is demonstrated at several sites even with conventional column alignment.INTRODUCTIONThe DJM method is a representative deep soil mixing technique of dry mixing manner in Japan. DJM can successfully install soil mixing columns trough automatically controlled binder injection based on pneumatic feeding theory and cumulative experiences.This method was joint-developed in 1978 by private organization under initiative of the Public Works Research Institute of the Ministry of Construction as the optimum method for improving the Japanese soft ground. Figure 1 shows full view of the DJM construction system. Figure 2 illustrates DJM working system indicating Binder Feeding Plant side and Mixing Machine side respectively.As typical soil mitigation method, many projects related with rivers and roads and city development has required DJM technology. The total number of the projects applying DJM has exceeded 5,000 with the total treated soil volume more than 32,000,000 m3 by the end of fiscal year 2013."

Jan 1, 2015

By Fabio Santillan, Michael F. Zoccola

"Wolf Creek Dam and Lake Cum berland in Russell County Kentucky is operated by the United States Army Corps of Engineers (USAGE) Nashville District It is a combination 3,940 ft long (1,200 m) non-zoned clay embankment, a maximum of 215 ft (65.5 m) above top of rock and 1,796 ft long (547 m) concrete gravity section. Built in the 1940s, the limestone beneath the embankment is characterized by an extensive interconnected network of solution feature; varying from fist size to largecaves.In 2005, studies conducted by the Nashville Distrect concluded that a new seepage cut-off wall was needed as the existing cut-off wall, installed in the 1970s, did not go deep enough and did not extend laterally far enough to intercept all major karst features The dam was classified as a ""Dam Safety Action Classification I (DSAC 1) – Urgent and Compelling,"" the highest risk under USAGE risk category rankings. Also in 2005, under a USAGE risk screening program of its entire dam portfolio, Wolf Creek was classified as a Dam Safety Action Classification 1-Urgent and Compelling, which put it in the highest category. In 2007, an Independent External Peer Review from outside USAGE, concluded there was compelling evidence that a piping failure mode had re-initiated and was in an ""advanced continuation"" stage of development.Impounding approximately 6 million acre-ft (7.4x102m3) of water at flood storage, Lake Cumberland is the largest reservoir east of the Mississippi River and ninth largest in the United States. Catastrophic failure would result in widespread flooding, Ices of life and economic losses in billions of dollars.In 2008, the Nashville District partnered with a joint venture between finns Treviicos and Soletanche (ISM through a ""Best Value"" contract to construct a new seepage barrier wall. This acquisition method was used in lieu of a low bid contract due to complexity of the work and dam safety concerns. It took advantage of the experience and innovation of contractors by soliciting technical proposals that were evaluated independent of cost. Those proposals deemed technically qualified and responsive then underwent a trade-off analysis between ccst and technical approach and a selection was made of the one deemed to give the best combination."

Jan 1, 2013

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By Emad Farouz, Francis A. Abreu

"This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule.This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.SITE AND PROJECT DESCRIPTIONThe Great Neck Water Pollution Control District (GNWPCD), located in the Town of North Hempstead in Nassau, New York, owns and operates a municipal wastewater treatment plant (WWTP) that discharges treated effluent through an outfall to Manhasset Bay, which is a tributary of the Long Island Sound. The site is located west of Manhasset Bay and is surrounded on three sides by local roads, and commercial, industrial, and recreational properties. The site has a gentle slope ranging from elevation +20 to +7 from west to east, respectively, based on the Nassau County Datum.To comply with new nitrogen discharge requirements and new design flows, the GNWPCD contracted CH2M HILL, Inc. and William F. Cosulich Associates as a Joint- Venture (JV) to design and provide services during construction of eight new advanced nitrogen removal facilities."

Jan 1, 2017

By Suresh Chikati, Gangadharan Santhanam

Twin tunnels were constructed to a length of 863m using TBM in one of the underground metro projects. The tunnels pass through complex geological conditions (soil, rock and mixed conditions). This paper presents the consideration of volume loss and the corresponding ground settlement associated with the excavation of twin TBM tunnels by analytical and numerical methods. Empirical methods were used to calculate the ground settlement induced by the excavation of twin tunnels. The ground settlement values were directly derived from the two parameters: the volume loss and trough width parameter. These parameters are calculated based on the geological conditions at the tunnel face and tunnel overburden. The finite element software, Plaxis 2D was used to model the soil parameters with appropriate geological conditions. Twin tunnel excavation is simulated in Plaxis 2D and the effect of tunnelling on the ground was simulated by percentage volume loss. The suitable line contraction value was applied to the tunnel linings to simulate the volume loss. The surface ground settlement was directly obtained from Plaxis 2D. Instrumentation arrays were proposed along the twin tunnel alignment, to provide the ground settlement monitoring data within the influence zone of tunnelling activities. The derived ground settlement values from analytical and numerical methods were compared with the actual field instrumentation and monitoring data. From the field instrumentation data, the actual volume loss values were calculated. The compatibility of ground settlement and volume loss calculated using analytical and numerical methods and those measured using field instrumentation data is discussed in this paper.

Sep 1, 2022

By Khamis Y. Haramy

Curing temperature, density, and moisture significantly affect the velocity measured in the crosshole sonic logging, the rate of strength gain, and the final strength of concrete in drilled shafts and, thereby, affect their structure capacities. Non-destructive field measurements can enhance the QA/QC program by measuring temperature, density, moisture, and sonic velocity of curing concrete during the construction and curing of drilled shafts. The curing environment can greatly affect the concrete strength, and requires close attention during construction. This article shares the experience with the NDE technology used in the QA/QC program in the drilled shaft construction. To understand the mechanism by which a drilled shaft cures under field conditions, two newly constructed drilled shafts were monitored for up to seven days, immediately following concrete placement using the following geophysical logging methods: a) temperature logging; b) crosshole sonic logging; c) gamma-gamma density logging; and d) neutron-moisture logging. One additional drilled shaft was also monitored to a shorter duration. Temperatures were monitored using the sensor in access tubes and/or thermocouples embedded at the center of a drilled shaft and near its reinforcing cage. For a small shaft under 1m diameter, curing temperatures appeared to peak at 41° ? 68° C at different depths at around 24-hour curing time and decreased to and stabilized at around 23° ? 35° C in 6 days. The shaft curing rate varied with depth, shaft diameter, surrounding geo-material types, and the depth of ground water. CSL logging was performed in one shaft from top to bottom from six access tubes and limited monitoring in another shaft. The velocity increased with curing time till 4 to 7 days, and, at a specific time, the velocity appeared to be inversely correlated to curing temperatures. The gamma-gamma density log (GDL) results from 5 different depths were obtained at a source-detector separation of 355 mm. The average density was found to increase with curing time, but decrease slightly in 3 to 5 days. At a given time the GDL density curves seemed to correlate with the neutron monitoring logging (NML) moisture curve. The NML moisture was monitored from 1st to 6th day after concrete placement. The moisture was highest when surrounded by bedrock, then clay, and sand due to different hydration rates.

Jan 1, 2007

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By George Aristorenas, Carlos Englert, Jesús Gómez

"Laboratory test data of strain softening soils exhibit the development of a maximum (peak) shear strength followed by a decrease in the strength with continued straining. The rate of strength loss decreases such that an asymptotic minimum value, known as the residual strength, is approached. This paper presents an investigation of the evolution of strength degradation in excavation supported soils that exhibit strain softening behavior. The paper presents a numerical investigation of excavation support of slicken-sided clay, and results of shear testing on materials with similar strain softening behavior. A strain softening constitutive law is presented that can be used with the finite element computer software Plaxis for analysis of excavation support. A typical design section of a deep excavation support in stiff, fissured clay is presented that illustrates the limitations and conservatism of the residual strength approach for excavation support design. Finally, a discussion is presented on the impact of stiffer walls such as diaphragm walls, compared to less stiff systems such as sheet piles, on the design parameters.INTRODUCTIONIn the Washington, D.C. metropolitan area, the Potomac Formation is generally composed of stiff, fissured clays. Geotechnical engineers often associate the presence of slicken-sided planes within the formation as evidence that the soil cannot develop its peak strength. Although it is unclear how old and continuous these slicken-sided planes are, their occurrence, persistence and orientation appear to be somewhat random. Due to this uncertainty, the design of open cut slopes in these materials is often conservatively performed assuming residual shear strength values. This design approach may be justified for long-term open cuts when there is limited amount of geotechnical information and in view of back stability analyses of past slope failures. Furthermore, the lack of confinement in open cuts allows relatively high shear strains near the surface and toe throughout their existence, which promote mobilization of post-peak strength values and the ensuing progressive failure. Indeed, such behavior has been discussed in the past (Skempton, 1970; Schnabel et. al., 1982; Derrenbacher, 1998). A thorough study by Mesri et. al. (2003) of numerous slope failures concludes that the lower bound strength for stability analysis of non-failed slopes is the fully softened strength, which is intermediate between the peak and residual strengths, but that part of the slip surface may be in a residual condition prior to failure."

Jan 1, 2015

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy"

Jan 1, 2017

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy."

Jan 1, 2017

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

By Roberto Nova

The selection of the Osterberg Cell (O-Cell) technology as the standard testing method for deep foundations of the Railways Po Viaduct in Northern Italy offered a relevant number of field measures on large bored pile behaviour in alluvial soils. The assessment of pile response during such ?non standard? testing procedure was performed through the comparison with standard top load tests on companion piles as well as by numerical models of the tests including a simplified pile-soil interaction scheme. As shown in this paper, the O-Cell technology allowed a careful assessment of the non-linear pile behaviour even at quite small loading levels as those required by a posteriori proof tests on production piles. Simple numerical models proved to be very effective in the simulation and the interpretation of pile behaviour during such unconventional testing procedure.

Jan 1, 2008