Search Documents

By Adrian Dance

Newmont Mining Corporation?s Carlin (?Carlin?) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (?PTI?) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study. Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load. The secondary crushing plant demonstrated it was capable of reducing the amount of +¾? material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size. For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study.

Jan 1, 2012

By David R. Ray, Arthur J. Pyron, William F. Thomann

"Proterozoic plutonic and volcanic rocks in the Franklin Mountains, west Texas, exhibit similar values in average concentrations of equivalent uranium (eU), equivalent thorium (eTh) and equivalent potassium (eK) when compared to Proterozoic igneous rocks of the southwestern United States. Variations of radioelement concentrations for all Proterozoic igneous rocks of the Franklin Mountains range from 1.1 to 357.1 ppm U, 2.1to 259.1 ppm Th and 2.5 to 10.2% K.Recent geologic mapping of the Proterozoic rocks in the Franklin Mountains revealed several types of granites previously unrecognized, and these warrant further exploration for U and Th resources. Fluorite-bearing granites and riebeckite pegmatites are likely targets for further investigation, as these have the highest U and Th concentrations compared to all other granites.IntroductionThis is a summary of the paper presented at the CIM Geology Division Uranium Symposium held in Saskatoon, Saskatchewan, September 8-13, 1981. The purpose of this study was to evaluate the distribution of uranium (U), thorium (Th) and potassium (K) in Proterozoic igneous rocks in the Franklin Mountains, and compare radioelement concentrations to Proterozoic igneous rocks elsewhere in the southwestern United States.General GeologyThe Franklin Mountains are located in west Texas and southcentral New Mexico, within the southeastern part of the Basin and Range Province o f the southwestern United States. The Franklins are a complex fault-block range trending northsouth with strata dipping toward the west. Ages of the rocks range from Proterozoic to Cretaceous. Harbour (1972, 1960) provides the most recent account of the general geology of the Franklin Mountains. Most recent accounts of the detailed Pro Proterozoic geology o f the Franklins are provided by Hoffer (1976), Thomann (1980, 1981), Pyron (1980), Ray (1982) and McCutcheon (1982)."

Jan 1, 1983

During the past decade, the miner-al industries have been faced with an increasing shortage of engineers. The point has now been reached where the shortage may be termed critical. This shortage may be attributed directly to declining enrollment in the mineral science programs offered by the universities on this continent. Although the reasons for declining enrollment are undoubtedly many, two major hypotheses may be postulated. The first is that high-school graduates are either unaware of the mineral industries and the opportunities in them or that they are aware of them but have somehow obtained a false image of their true nature. The second is that they are aware of the true nature of these industries and the opportunities they offer but find them exceedingly unattractive. The problem of dwindling enrollments has, in recent years, been subjected to a concerted attack by the industries and professions concerned. However, their efforts to date have been based essentially on the first hypothesis. Sufficient results are now available to suggest that either the methods of attack are inappropriate

Jan 1, 1965

By A. B. C. Stothart

"IntroductionIn the past four years Ontario Mines have made great progress in the development of reliable mine conveyance safety dogs. History shows that, prior to 1945, a rope failure on a descending conveyance was usually followed by unsatisfactory safety dog operation.It is proposed in this paper to discuss briefly;The history of this development. Progressive .development of one type (E. Long).Free fall testing of safety dogs. Anti-trailing rope device.HistoryOn February 2nd., 1945, a hoisting rope broke at the Paymaster mine. The safety dogs proved ineffective and permitted the cage to crash through to the bottom of the shaft, with disastrous results.Following this accident, the Ontario Government appointed a Technical Committee to investigate The Safety of Hoisting Equipment and Hoisting Practice in Ontario Mines. This Committee consisted of Dr. C. R. Young (Chairman) and Professors T. R. Loudon, E. A. Allcut, V. G. Smith, and Lloyd M. Pidgeon. The Ontario Mining Association (at the request of the Ontario Government) also appointed a Committee consisting of Messrs. R. E. Dye, R. D. Parker, and R. L. Healy."

Jan 1, 1950

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By B. Chambers, M. Yunovich

"Corrosion monitoring is commonly used in a variety of industries as a means of effective corrosion control programs to extend the life of the asset and ensure safe operation of the facilities. The majority of the monitoring tools have limitations and tradeoffs – e.g., sacrificing the longevity of the probe for higher measurement resolution. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity. In many instances, utilization of LPR probes in conditions with intermittent wetting (for example, conditions where the temperature fluctuates above and below the dew point) presents a challenge. To address this limitation, a special-design cooled corrosion probe has been developed, commercialized and integrated into the distributed control system in the plants. In addition to high-accuracy measurement of corrosion rates, the probe allows for monitoring of pitting corrosion. The most innovative feature of the probe is the cooling circuit, which brings the temperature of the sensors below the dew point, forcing precipitation of moisture and thus permitting corrosion measurements. Additionally, the probe was found to be well-suited for monitoring corrosion in crude distillation unit (CDU) overhead space, where condensation of hydrochloric acid may take place at relatively high temperatures, which would require relatively moderate amount of cooling to be imparted to the probe sensors. This paper presents laboratory-based data from a test simulating CDU refinery environment. A case study is presented to demonstrate how the cooling probe can be effectively used in the plants for corrosion monitoring.INTRODUCTIONConventional corrosion-monitoring techniques such as weight-loss coupons to assess corrosion damage are commonly used in plants1. However, the use of coupons is not only labor-intensive, but also does not deliver real-time corrosion data, thus effectively serving as a “backwards-looking” monitoring tool. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity."

Jan 1, 2012

By Louis Frost

"1N 1951, the Dominion Steel and Coal Corporation, as part of a programme of modernization in their coal mining operations at Sydney Mines and Glace Bay, Nova Scotia, undertook the development of two large cross-measure tunnels, which were to be used for the purpose of raising the coal from the underground workings by conveyor belts direct to wash plants located on the surface.These tunnels were to reach from the surface to central loading points underground located at a depth of 600 and 900 feet, respectively. They were to be driven on a pitching gradient of 11 degrees to the horizontal, and they were to reach a length of 3,600 feet in the Sydney Mines area and 10,000 feet in the Glace Bay area.The longer tunnel, 19 feet in diameter, was driven a distance of 1,500 feet and, for domestic reasons, bas not yet been •completed. The other tunnel, in the Sydney Mines area, 18 feet in diameter, is steel supported and concreted throughout its entire length. This tunnel has been completed and will be in operation at an early date.The development of this particutar tunnel posed an additional problem, as the rock through which it had to pass was considered to be water-bearing. In the sinking of Princess Colliery shafts in 1866, a great deal of water had been encountered, and it had been necessary, while sinking, to line the shaft with cast-iron tubbing through the water-bearing strata. The shaft had to be lined for a depth of 300 feet at the upper end. It was anticipated that we would meet with difficulty in driving the tunnel through this strata."

Jan 1, 1955

By C. Acuña

The case is presented that the key role of frother is control of bubble size in the pulp zone. Compared to water alone, the addition of frother produces a narrower distribution and finer bubble size. An empirical model is presented for bubble size as a function of frother type using a normalized concentration. The model provides a benchmark for assessing operations. There is no agreed upon mechanism of how frothers act to reduce bubble size. Prevention of coalescence is a common explanation and this action is illustrated. The case against the 'coalescence' model alone is presented and a breakup mechanism is introduced based on pilot cell and single bubble studies. Phenomena associated with bubble shape, velocity and surface flows are used to illustrate the force associated with surface tension gradients. Breakup mechanisms resulting from this force are proposed. The concept can be extended to high salt concentrations which also promote small bubbles.

Jan 1, 2007

By Douglas Brand

"The data that many mineral processing plants make use of, is provided by samples taken from sampling systems which are inadequately designed or improperly maintained, and therefore cause detrimental effects to plant operations, production planning and metallurgical accounting! Poorly designed or maintained sampling systems will likely produce low probability samples which give the operator a false sense of security of the product and the process. If data is the basis for action (Flintoff, 1992, p.2), then using the resulting suspect or bad assays by operators, control systems, or metallurgist and administration personnel will act and make decisions which may adversely affect the profitability of a processing plant. Here we will discuss some of the fundamental sampling problems, propagation of errors and a method to estimate what impact this has on an operations Net Smelter Return.INTRODUCTIONIn order to control a mineral processing plant at its best potential, it is necessary to obtain the best possible measurement results of the metal or mineral in question. The sample which is delivered to a measuring instrument, or lab, needs to be of the highest probability to be able to achieve this. This paper will discuss the effects of sampling errors on grade / recovery and grade / Net Smelter Return (NSR) and provide a method to estimate the monetary advantages of using probabilistic sampling in a processing plant.REVIEW OF SAMPLINGSampling, by definition, is the removal of a small representative portion from a total consignment, or flow, for the purpose of accounting or process control.• A sample can only be considered representative, if each and every increment collected, in each of the sampling stages, is representative.• Each particle of the sampling lot must have the same probability of being included in the final sample.• If both of the above conditions are met, then the final sample will be representative of the complete sampling lot.It is commonly known that in order to take truly representative and probabilistic sample, best practices indicate that:• The total stream should be sampled.• The sample cutter should intersect the sample at right angles to the flow.• The sample cutter should travel through the stream at a linear and constant speed and the speed deviations should be less than 5%."

Jan 1, 2016

By D. Stone, N. J. Aslin, W. Webb

In today's modem copper electro-refineries, increasingly higher average current densities are being employed. With these increases many refineries are approaching their limiting current density. The nearness of the average operating current density to the limiting current density has placed increasing emphasis on the need to maintain an even current distribution. This paper explores the importance of maintaining even current density and discusses the factors, processes and practices that are necessary to achieve and maintain high quality production at high operational intensity.

Jan 1, 2005

By T. Johnson, D. Kelley, J. Graham

"Hydrometallurgical processes can be exceptionally corrosive. Conditions associated with metal extraction and refining require materials of construction that can withstand process acids and acid chlorides at temperatures up to 90°C (194°F). Process vessels, piping, scrubbers and ducting can be rapidly compromised in these aggressive environments if not designed with care. Design engineers are challenged to find materials that can stand up to hydrometallurgical processes especially for copper, zinc, nickel, cobalt and uranium. This paper will evaluate material solutions to determine which provides attractive economics for initial procurement as well as high durability for reasonable life cycle costs.INTRODUCTIONMining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel cobalt and uranium have been particularly active.The world’s largest nickel mine – the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale’s Voisey Bay mine in Labrador. Voisey’s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $858 Million Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 – 250,000 MT/yr manganese carbonate.High nickel alloys and rubber lined steel have been used for decades to design corrosion resistant equipment for mineral processing environments. These materials demonstrate reasonable resistance to corrosion for most environments. Unfortunately, higher nickel alloys are quite expensive. Rubber lined steel is a bit more affordable but requires continuing service over time which ultimately drives up its cost as well. FRP (Fiberglass Reinforced Plastic) has also been used extensively in mineral processing for tanks, piping and ducting employed in aggressive environments. Today, more and more design engineers and material specifiers are calling for FRP composites for both new and replacement equipment used in the refining and processing of a variety of metal ores."

Jan 1, 2012

By M. B. McClenaghan

"Abstract - The Matheson area of northeastern Ontario is of great interest for mineral explo­ ration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has be­ come an important exploration method. The Ontario Geological Survey&apos;s Black River -Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift ( < 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north­ northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (<50 1-1m) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of s3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By S. R. Knowles, R. J. McDonough

"The purpose of this paper is to introduce to the minerals processing marketplace a viable alternative to conventional mechanical agitation and pachuca airlift agitation. What follows is a brief introduction to the Atara Corporation and the fundamentals of how an Atara ""cannon"" mixer operates. The main body of the paper is concerned with the results of a study to evaluate the cannon mixer for a gold cvanide leach application. A brief summary of research and testing for other metallurgical applications is also presented.1. 1 THE COMPANYThe Atara Corporation is a privately owned Canadian company, headquarted in Dorval, Quebec. Its subsidiary, Atara Incorporated, located in Paramus, New Jersey services the municipal wastewater treatment market in the United States. Dorval focuses on industrial mixing applications in Canada and the US. The Atara Corporation provides design, engineering and specifications of agitators for mineral land other) processing applications. Fabrication of mixers is pursued in either Canada or the US, depending on the ultimate destination.Although Atara and its unique static in-tank mixer are relative newcomers to the mining industry, the cannon mixer has demonstrated its value over the past 20 years in municipal wastewater treatment services. In the past four years the Atara unit has been developed for industrial applications; the bulk of the development work has been for metallurgical applications. To-date the cannon mixer has been evaluated for mixing slurries in the following applications: nickel-copper concentrate storage, copper concentrate storage, coal slurry storage, gold cyanide leaching, uranium acid leaching, silver leaching and zinc acid leaching. Atara mixers have been installed with successful performance in full scale tanks containing nickel-copper concentrate slurry (Falconbridge) and gold cyanide leach pulp (Dome"

Jan 1, 1984

By Richard Klimpel

"Over the last 15 years, there has been a number of plant scale sulfide mineral flotation tests organized by this author specifically aimed at understanding how flotation rate varies with reagent type and dosage. With regard to the Interaction of collector dosage, particle size, and frother type, the eight specific trends listed in the paper (Illustrated with data from two specific case studies) are qualitatively the same for almost all plants studied in some depth. The Interaction of flotation rate K and equilibrium (Infinite time) recovery R in the plant has been denoted as the R/K trade-off. The effect of collector dosage on the rate of flotation of specific particle size intervals is particularly interesting and once understood, is quite useful In understanding how industrial flotation plants respond to changing reagent type and dosage. The location and magnitude of the R/K trade-off can be different for various ores and various plant configurations, but the RIK trade-off is almost always present. The purpose of this paper is to clearly describe and illustrate the nature of this very Important flotation system Interaction so that operating engineers have a starting reference point for beginning successful plant Improvement studiesIntroductionIt is well recognized by industrial froth flotation plant operators that improving existing sulfide circuit performance is often difficult due to the self-compensating systems nature of the froth flotation system, e.g. Klimpel (1988, 1989, 1995). Extensive plant testing with existing and new reagents by this author throughout the world has clearly shown that one of the more important self-compensating mechanisms is the Interaction between collector dosage, frother type, and particle size. The term self-compensation in flotation simply means that as the plant operator consistently changes one parameter in the same direction, the nature of the froth flotation system Is such that the circuit will eventually begin to resist this controlled parameter change by automatic (uncontrolled) changes In other parameters and the overall circuit performance will go through a maximum or minimum (hence causing the operator to stop the parameter change)."

Jan 1, 1997

By W. N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are situated in south-central Yukon, some 120 miles north of Whitehorse. The large lead-zinc concentrator employs conventional crushing and grinding , followed by differential flotation, to produce selective lead and zinc concentrates, as well as a mixed lead-zinc (bulk) concentrate. Since the commencement of operations in 1969, the concentrator has undergone expansions and modifications which have increased the capacity to 10,000 tons per day, and afforded some metallurgical improvements.

Jan 1, 1978

By X. Cao, H. Huang, Z. Dai

"Crystal phase of copper-containing slag regulation by the slag viscosity, cooling speed and cooling method, where the slag viscosity is related to the temperature and alkalinity. According to the mineralogy properties of a copper-containing slag, experiments of crystal phase regulation and flotation were conducted. When the copper-containing slag that adding a small amount of calcium oxide was cooled slowly at a rate of 3°C/min and about 1050°C n a cinder inclusion system, the viscosity of slag can be remained under 0.25 Pa·S and more than ??% of copper particles that the grain size is larger than 20 ?m in slag. The whole flow of flotation experiment was carried out to recover copper from the copper-containing slag with crystal phase regulating and the copper concentrate grade was ?????%, the recovery efficiency of copper was 94.18%.INTRODUCTIONChina's annual output of copper slag is more than 6 million tons, the current total has reached 80 million tons. It is equivalent to 640 thousand tons of copper metal with the copper grade of 0.82%. Most of the smelting slag were storage. It is not only occupy the land and pollute the environment, but also make a huge waste of resource (Alp, Deveci, & Süngün, 2008; Carranza, Iglesias, Mazuelos, Romero, & Forcat, 2009; Gorai, & Jana, 2003), therefore, it is good way to achieve copper slag resources by the effective recovery of valuable component from copper smelting slag, which is an important measure of the current process of copper smelting slag and implement the central authorities to vigorously develop the circular economy, improve the recycling of resources, increase copper production of intensive development (Zhou, et al., 1994; Zhang, Zhang, & Wang, 2005). Currently, researches on comprehensive utilization of the coppercontaining slag made a much progress (Wei, 2004; Liu, Gai, Yang, Sui, Li, & Fu, 2008; Liu & Zhu, 2008; Zhang, 2010; Sun, Chen, & Tang, 2012; Qin, Wang, Ren, Wei, Peng, & Gu, 2012). Flotation is one of the most effective method to recover the copper from smelting slag, which has the features of low cost and high efficiency (Song & Liu, 2001; Zhang, Wang, & Li, 2012). But the copper particles in the copper smelting slag distribution is very uneven, and the thickness of the material is very serious. The copper content in the micro level is higher, the size of copper sulfide ore is less than 0.043 mm, which leads to the difficulty of the monomer dissociation (Tossavainen, Engstrom, Yang, Menad, Lidstrom, Larsson, & Bjorkman, 2007; Moustakas, Mavropoulos, Katsou, Haralambous, & Loizidou, 2012). In this study, according the process mineralogy of a smelting copper slag, the crystal of smelting copper slag was optimized by controlling the temperature, alkalinity, cooling rate and cooling method, which makes the fine copper mineral particles in the copper slag crystal further, and can be used to meet the particle size requirements of flotation, thereby enhancing the flotation of copper."

Jan 1, 2016

By A. H. Lang

Introduction Tin continues to be as much a strategic metal as it was during the war. This situation is due to the fact that the tin mines in the major producing areas of Malaya and the Netherlands East Indies have not yet reached their pre-war production. Moreover, the world requirements for tin in certain fields, particularly in the food pack industries, are steadily increasing. At present, tin is still under International allocation by the Combined Tin Committee, of which Canada is a member nation. This Committee reviews periodically the availability of refined tin for export from the producing countries and makes allocations of tin to ensure equitable distribution to the consumer countries. In 1947, availability permitted an allocation of only 70 per cent of stated requirements. From 1935 to 1938 the price of tin in New York averaged 49 cents a pound and during the war the price in Canada was controlled under a subsidy programme at levels from 60 to 70 cents per pound. Just recently, this price has been raised to 96 cents. The value of the Canadian production amounts to about half a million dollars annually and the whole of this is obtained as a by-product of the lead-zinc-silver ores of the Sullivan mine in British Columbia. In 1947 Canada&apos;s imports of tin were 3,961 long tons valued at over $6,000,000. In addition, tin plate to a value of $8,000,000 was imported from the United States; the tin content of this is estimated to be from 650 to 700 long tons. An increase in domestic production would, therefore, be of great national importance, and the present high price may make the search for and development of tin deposits more attractive than it has been in the past. Although no one can foretell what future prices will be, there is reason to believe that, unless there is a drastic downward revision of production costs, the price will be maintained at present levels for some years. A number of tin occurrences are known in Canada, but none of these have been developed for their tin content alone.

Jan 1, 1948

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962