Search Documents

Background ArcelorMittal?s (formerly QCM?s) Port Cartier iron ore pelletization operations 2 side-by-side induration furnaces each producing 578 t/h of cured pellets Firing No. 6 fuel oil and coke breeze (in bed) Very large heat losses to be addressed primarily by gas recirculation

May 1, 2011

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006

By Roberto Pena, Cristhian Morales, Darwin Morales, Veronica Cambiaso

"This article makes evident the shortcomings of the current operation of oxygen pipes as well as the damages they cause and why they cause them. When focusing on the causes and effects of these drawbacks, it was possible to develop a new family of thermal lances that could pierce a taphole with the precision of a drill but with the capacity to complete the whole operation. Although efforts have been made to replace oxygen pipes since they are annoying, dangerous and inefficient, nobody had worked to improve the way the traditional oxygen pipe taps/perforates the furnaces and reactors tapholes. In fact, developments made in drills and robotic arms, have failed to replace the oxygen pipe, which despite their negative side effects have been used for more than a century. Observation and theory were key to radically transform this humble tool into a dependable and efficient support in the operation. A good news that it is worthwhile to share for the benefit of all of us, passionate about the world of pyro metallurgy.INTRODUCTION Normally, reports and papers prepared for conventions, symposia or other technical events related to metallurgy aim to relevant topics in the operational field, probably because in them lay the scale economies every company pursues. We intend to give relevance to a matter normally disregarded in operations, but that unmistakably vital: if the furnace or reactor cannot be bled, the pyrometallurgical process will not be completed. Besides, if the tapping task is difficult or is long delayed, the availability of the furnace will be reduced. Consequently, there will be a waste of energy and workers will be exposed to dangerous levels of radiation as well as to work overload and physical injuries Apart from these basic effects, in tapping operations where oxygen pipes are used, we can see serious damages in the smelting furnace, especially in the taphole components such as refractory bricks, taphole jackets and water cooled plates. This paper intends to show that taking care of the tapping task can significantly upgrade not only to the tapping operation itself, but also the whole plant productivity."

Jan 1, 2017

By R. Burnette

Gold has been mined from a variety of deposit types that range in age from Archaean to Recent. The large variability in the geological settings of the gold deposits implies transport and concentration of gold by magnetic, hydrothermal and sedimentary processes. The factors that control the concentration of gold at certain sites and the grade estimation thereof remain major topics of debate. Due to the complex nature of the Witwatersrand Basin a mineralogical study, including mineralogical, petrographic and geochemical investigation was launched on TauTona Mine in order to characterize the various reef facies. The aim of the investigation was to determine if a correlation could be found between macroscopic characteristics of the reef, hanging wall and footwall, and the microscopic nature of the ore (especially gold grade). Petrograpgic and mineralogical results indicate that a correlation exist between gold, detrital and hydrothermal sulphides, uraninite, carbon, detrital heavyminerals and phyllosilicates. No correlation exist between gold and Mg, Fe or S. It appears that clast supported reef is of higher wade than matrix supported, but more work is suggested. No correlation exists between reef thickness and grade. The reef samples had the lowest phyllosilicate content compared to the hanging wall and footwall samples with pyrophyllite the most dominant. All of the correlations diagrams showed significant scatter and suggests a multi- factorial mineralization model. Gold distribution is also controlled by sedimentary features and thus it is not possible to select a single model for the formation and distribution of gold. It is evident that both sedimentary and hydrothermal factors influenced the mineralization and gold distribution on TauTona mine. It is thus essential that all related theories be incorporated in the development of a grade prediction model.

Jan 1, 2011

By E. W. Shaw

The past year (1950) has been a big one for the oil industry in Canada, with new records being set in almost every phase of exploration and development activity. New highs were reached in acreage holdings, in geophysical activity, in wildcat drilling, and in field development and production. The only item that did not show a substantial increase over recent years was the amount of reserves added by new discoveries. This was not due to a decrease in the number of new discoveries, however, hut rather to the fact that most of the discoveries were made during the later months in the year and could not be fully evaluated by the year end. The foregoing remarks pertain mainly to activity in Western Canada. In Eastern Canada, operations continued on a modest scale. with exploration drilling down slightly from the previous year but with development drilling and production at about the same level. Returning to Western Canada, it is observed that the general exploration play was one of expansion and intensification. The issuing of new petroleum and natural gas regulations by the province of British Columbia precipitated a moderate entry of companies into the northeastern part of the Province.

Jan 1, 1951

By J. L. Llanca

The New Level Mine project (NLMP), the planned underground expansion of the El Teniente mine in Rancagua, Chile, is expected to reach a daily extraction rate of 137 to 180 ktpd upon achieving full capacity. Production is planned to start in the year 2017 and the current plan is to meet that target through two development phases, from the year 2012 to 2014 and from the year 2015 to 2017. To achieve the 2012 to 2014 underground development schedule, the ventilation requirements have been estimated in the range of 189 m3/s (400 kcfm), and cannot be made available without significant modifications to the current system of El Teniente. As a result, a certain number of alternatives were explored to find a solution to this shortfall, for example, adding raises to generate parallel airways and installing fans to reinforce the current ventilation system. From the alternatives studied, the installation of a second main fan (system) in parallel to an existing one was identified as the best solution, and selected for implementation, however the location was not ideal and there were concerns as to the operation of both fans once the second fan was installed. This paper presents the study used to estimate the operational points of both the current and the new fan, and to justify the parallel installation of the additional main fan. An additional computational fluid dynamics study was undertaken to validate the operational point, given the particular geometry of the fan?s location and placement, to guarantee a stable operation of the fans. Finally, the protocols arising out of this work for starting the fans, and operating them in parallel to avoid generating a stall condition and damaging the investment are discussed.

Aug 1, 2013

By M. Lindgren

"Hydrometallurgical processing involves process stages, like leaching, that create harsh environment for stainless steels. High acidity, the presence of chlorides and oxidizing ions combined with relatively high temperature create risk for both uniform and localized corrosion. Advanced electrochemical techniques were employed to study uniform and pitting corrosion of two stainless steel grades 316L and 2205. Results obtained with the linear polarization resistance technique combined with the harmonics distortion analysis, electrochemical noise and coupled multielectrode array systems are compared to the results of conventional electrochemical techniques and immersion tests.INTRODUCTIONHydrometallurgical processing has become favoured in metals production in recent years due to energy costs, leaner ore bodies and environmental factors. Because the hydrometallurgical processing route is flexible, various types of secondary raw materials, like flotation tailings, dusts, sludges and slimes can also be treated in addition to conventional mineral concentrates (Sarveswara Rao & Acharya, 2008).Hydrometallurgical processing relies on aqueous chemistry, usually acids, at temperatures around 100°C for the recovery of metals from ores, concentrates, recycled or residual materials. The processing route can typically be divided into three stages: leaching, solution concentration/purification and metal recovery. The processing environment is aggressive, especially in leaching. High acidity, relatively high temperature together with impurities, like chloride ions, place high demands on the corrosion resistance of construction materials. The dominant corrosion mechanism may be uniform corrosion or localized corrosion depending on the process conditions (Ekman & Torsner, 2010). This complicates the prediction of corrosion rates and, consequently, cost effective material selection.Traditional means to evaluate uniform corrosion resistance of stainless steels are immersion tests and the results are published in the form of iso-corrosion diagrams (Outokumpu Stainless, 2010). For the localized corrosion, namely pitting and crevice corrosion, immersion tests can be used but the duration of the test is rather long because an incubation period takes place prior to the occurrence of the actual localized corrosion damage. Electrochemical techniques, traditionally in the form of cyclic polarization scans, have been employed to assess the susceptibility of a material to pitting corrosion (Papavinasam, 2008). They cannot, however, give any indication of the pitting corrosion rate and lack potential for on-line measurements."

Jan 1, 2012

By H. A. Pearse

The history of the flotation process, as applied to the practical field of ore dressing, dates back somewhat less than twenty years; yet this fact may be overlooked in view of the present universal dependence on this process in the concentration of almost all classes of ore. It is therefore interesting to recall that Britannia was the scene of some of the earliest experiments with flotation on a commercial scale. In 1911, sixteen years ago, an Elmore vacuum machine was operated for several months with encouraging results. In 1913, some time before flotation was very generally adopted elsewhere, a Minerals Separation plant, capable of treating 600 tons daily, was operating successfully at Britannia. Considering how little was known of the theory and practice of flotation at that time, the recovery was remarkably good, but it was not until the present mill was completed in 1923 that any attempt was made to raise the concentrate grade by differential flotation, or, in other words, to float the chalcopyrite while rejecting the then worthless pyrite with the tailings. The first ore passed through the present concentrator in March, 1923. As originally designed, the rated capacity was for 2,000-2,500 tons, but this has been increased year by year, until at the present time 4,000 tons daily can be treated economically. During the first few months of operation the concentrate grade averaged only 10-11 per cent Cu, but by the end of 1923 this had been raised to over 20 per cent, due to the elimination of the pyrite by differential flotation. In 1923 the tailings averaged approximately 0.25 per cent Cu, but also in the matter of recovery a considerable improvement has been effected, for during the year 1926 an average tailing of 0.15 per cent Cu was maintained.

Jan 1, 1927

By Randy Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Occasionally mine operators are unaware of the presence of free gold particles in their ores because they have not seen free gold hand specimens or at the working face of the mine.Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment. The trapping and subsequent release of gold particles can frustrate attempts to calculate accurate metallurgical balances.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1997, 1998, 1999 and Walsh, 1986, 1992). In 1995, the author used radiotracers to locate and eliminate gold traps at La Mine Doyon (Clarkson, 1997). In 1998 and 2001, the author also salted mineral processing circuits at Royal Oak's Pamour Mine in Timmins (Clarkson, 1999) and at Gold Corp’s Red Lake Mine in Ontario with radioactive gold particles.The gamma and X-ray radiation from gold's nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment with scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps, improving security, determining the recovery efficiency of Knelson gold concentrators and estimating retention times of gold particles in various processes."

Jan 1, 2003

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool's dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006

By Gregory C. More O'Ferrall

Generally pillars in the Southern African hard rock tabular underground mining environment are designed using either empirical pillar design formulae or numerical modelling (analytical) methods utilizing the Hoek-Brown failure criterion. However, none of the pillar design methodologies employed takes cognizance of weak layers either within the pillar material or in the immediate foundation of the pillar. Over the past few years, the presence of a weak layer either within the pillar material or within the immediate foundation of the pillar has resulted in the closure of one platinum mine (Everest Mine), closure of one chrome mine (Wonderkop Chrome) and large-scale instability in a couple of chrome and platinum mines in South Africa and Zimbabwe. A study has been initiated to better understand the failure mode and strengths of the pillars where pillar failure associated with weak layers occurred. Owing to the infancy of the study into the failed pillar strength and failure mechanism, the purpose of this paper is to highlight the circumstances that led to the collapse of mining sections and a shaft, and the difficulty associated with designing pillars in the Southern African chrome and platinum mining operations.

Jun 1, 2012

By Y. M. Jubeli

"Abstract - Gamma-ray spectrometry, an effective tool in geological mapping, was used to define boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains. This paper describes the role of an airborne gamma spectrometric survey which was orginally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to significant modifications and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack sufficient geological data."

Jan 1, 1997

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

Pilot plants for pressure hydrometallurgy represent special design and project execution challenges unique to the industry and to the pilot- and demonstration-scale. Pilot plant projects have different objectives and shorter timescales than commercial plant projects. Design considerations and strategies, and project execution methods that meet the special needs of pilot plant projects, are discussed. Specific guidance is given for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical process equipment, and for the selection of materials of construction for pilot-scale equipment. The balance between the need for process similarity with future commercial operations and the realities of pilot-scale equipment is also discussed.

Jan 1, 2004

By G. M. Ritcey

The recovery of copper from low-grade solutions res ulting from dump leaching is well known, whereas the recovery from highly concentrated copper solutions has not been practiced. This paper discusses the use of Ashland Chemical's Kelex 100, a substituted quinoline, for the recovery of copper from solutions resulting from leaching copper-nickel concentrates. A flow sheet is described, and an economic comparison shows Kelex 100 to be superior to either the LIX 64N or LIX 70 reagents of General Mills for the recovery of copper.

Jan 1, 1973

By Y. M. Jubeli

"Gamma-ray spectrometry, an effective tool in geological mapping, was used to de?ne boundaries between various lithological formations in three adjacent areas of Central Syria, namely, the Syrian Desert, Ar Rassafeh Badiayat and the Northern Palmyrides mountains.This paper describes the role of an airborne gamma spectrometric survey which was originally undertaken to assist uranium exploration. Interpretation of the total count data obtained through the survey has led to signi?cant modi?cations and corrections to the previously published distribution map of the palaeogene phosphate rocks.Another important result of the survey is the discovery of four previously unknown phosphorite horizons in the Rasm Al-Aawabed area of the Northern Palmyrides. In addition, previously unknown phosphatic horizons are outlined in the other study areas. The importance of this technique as an effective prospecting method, not only for U but also for exploring for the economically important phosphorite formations in Syria, is emphasized. Furthermore, its role in geological mapping is stressed, especially in areas that lack suf?cient geological data."

Jan 1, 1997

By M. Doggett

All 231 Canadian primary gold mines that produced from 1946 to 2004 were analyzed with respect to their production and economic characteristics. Trend analysis revealed that the average annual capacity of Canadian gold mines, as measured by ore processed or gold produced, has increased over time. Conversely, the average grade of gold mines has decreased over time. The distribution of gold output is highly uneven: for example, the 22 giant mines producing more than 100 t (metric tonnes) of gold account for 62% of total output. Small mines producing less than 10 t Au account for 54% of total mines, but less than 4% of total gold. Each historical mine in the database was evaluated on the basis of a set of economic and technical assumptions to determine if it would be economic to develop today. Based on the net present value using an 8% discount rate, only 103 of the 231 mines were determined to be economic. About 80% of the uneconomic mines had less than 10 t of contained gold, and 63% had less than 5 t. It is concluded that these small mines would not be viable today due to a combination of real capital cost increases, and more stringent permitting and environmental regulations. The implication is that future gold supply in Canada will hinge on the discovery and development of a new generation of larger mines. Given that only one giant mine has been discovered in the past 20 years, it seems likely that gold output will decrease in the future.

Jan 1, 2007

By O. Matwijenko

"1. IntroductionThe Falconbridge Owl Creek open pit gold mine is located 17 km northeast of Timmins and 2.5 km west of the Kidd Creek metallurgical site. Diamond drilling first commenced in 1964 with open pit production commencing in 1982. Other operations within close proximity are the Canamax-Pamour Bell Creek Mine and the Falconbridge Hoyle Pond Mine.Since 1982, 1,216,000 tonnes assaying 4.5 g/t have been processed in six concentrators. This paper summarizes the metallurgy achieved with special emphasis on some of the unique problems encountered in the processing of this refractory ore.2. GeologyThe Owl Creek deposit, located 3 km north of the Porcupine-Destor fault is in easterly trending carbonaceously altered volcanic and sedimentary rocks. The deposit strikes east and dips steeply north.The ore body can be best described as a wedge shaped sandwich of volcanic basalt between the surrounding sedimentary greywacke. The north and south volcanic-sedimentary interfaces are marked by graphitic zones. The south graphitic contact is more continuous with its thickness varying from 5 m to 20 m as compared to 0.5 m to 3 m to the north. Quartz veins occur throughout the deposit with a predominant vein running along the south contact where it is characterized by numerous graphitic inclusions. Some veins carrying gold values intrude into the sediments in the north. With depth the sedimentary and volcanic zones taper while the quartz-graphitic zones appear to become more dominant."

Jan 1, 1988