Search Documents

By Brad E. Melanson

Because mine haul trucks consume considerable quantities of fuel, they are ideal candidates for the adoption of cleaner and cheaper fuels like natural gas. Impressive fuel cost savings will be realized in regions where liquefied natural gas (LNG) has cost advantage to diesel fuel, while also providing significant reductions of air contaminants and greenhouse gases. High Pressure Direct Injection (HPDI) of natural gas utilizes the diesel cycle combustion process and therefore retains the diesel engine?s high performance and efficiency characteristics. HPDI has been demonstrated in on-road Class 8 trucks since 2001 accumulating almost 10 million kilometres to date. The supply of LNG fuel will be an essential parallel aspect in the introduction of HPDI to mining. LNG can be transported to site as diesel is today, or may be produced on or near mine operations that have access to methane sources or pipelines.

May 1, 2006

By J. L. Jambor, R. W. Boyle

"The Magnet Cove barite-sulphide deposit is a raking pipe-like body that replaced and partly filled a large brecciated zone at the junction of two faults at the contact between sedimentary rocks of the Horton and Windsor Groups of Mississippian age. The principal minerals in the deposit are siderite, barite, hematite, pyrite, marcasite, galena, sphalerite, chalcopyrite, tennantite, proustite, pearceite, acanthite and stromeyerite. The mineral assemblage and textural relationships indicate that the minerals were deposited from low-temperature solutions. The source of the elements in the deposit is believed to be the enclosing sedimentary rocks, with connate or ground waters as the transporting medium, and solubility products as the governing factor controlling the abundance and order of deposition of the minerals."

Jan 1, 1966

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

By J H. Dressel, J. E. Williams

This paper presents a brief review of what coal gasification is, procedures that are available today and processes that may be available in the future. Examples are given as to how the process might be used in power plant applications, the effect on pollution level and power costs, and some thoughts on the added burden that might be placed on mining and coal preparation.

Jan 1, 1973

By A. F. Matheson

The St. John Del Rey Mining Company, Limited, is an English company owning 150 square miles -of mining lands near Belo Horizonte, Minas Geraes, Brazil. The area is 2,300 to 5,000 feet above sea level, with a pleasant and healthy climate. Bedrock is Precambrian. The Nova Lima series of metamorphosed sediments and some volcanics is overlain uncomfortably by the Minas series of quartzites, itabirites. etc. Batholithic granite and gneiss cut both series and basic dykes cut all these rocks. There are important deposits of gold, iron, and manganese on the Company's holdings, as well as occurrences of arsenic, antimony, cobalt, nickel, dolomite, day, quartz, -ochre, bauxite, kyanite, and asbestos. Except for gold and consequent recovery of arsenic, all the other materials are relatively unexploited. The Company operates the Morro Velho gold mine and the Espirito Santo and Raposos gold mine. The Morro Velho mine was purchased in 1834 for £56,000. To the end of 1952 it had produced 7,000,000 troy ounces of gold from 15,000,000 short tons of ore. The ore z?ones are replacement deposits in a sinuous siliceous dolomitic rock locally termed "lapa seca," and plunge east, near surface at 45 °, at 8,000 feet at 15°. The ore minerals are pyrrhotite, arsenopyrite, pyrite, and chalcopyrite. Gold is finely distributed and almost nowhere visible. Ore reserves at the end of 1952 were estimated at 5.5 million short tons grading 0.39 oz. gold per ton. Chances exist for new ore within the mine area. The Espirito Santo and Reposos mine, in folded banded iron formation, has mineralization similar to Morro Velho but sulphides are less abundant. The mine to a depth of 2,500 feet has estimated ore reserves of 1.5 million tons of an average grade of 0.28 oz. gold per ton. New ore may be expected both laterally and at depth. To the end -of 1952, the ?Company had paid dividends of almost £4,- 600,000, largely earned from the operation of the gold mines.

Jan 1, 1956

By G. Gabra, M. Nagamori, J. J. Panneton

"RESUMELa calcination contrôlée de 10 serpentine permet de produire de 10 magnésie active. Le degré de I'activation est mesure par 10 solubilité du magnésium dans les acides faibles tel que I'acide acétique, La serpentine contenue dans les résidus d'amiante du Québec peut donc être activée par calcination. Le teneur en magnésie active des rejets d'amiante calcinés est fonction de divers paramètres: température, temps de calcination, granulométrie, etc. Les rejets d'amiante de différentes provenances démontrent des comportements thermochimiques différents qui sont étudiés dans Ie présent travail au moyen d'ATD, de TG, de la diffraction des rayons X et de la lixivation par l'acide acétique. On constate qu'un maximum d'environ 80% de la magnésie totale peut être activé dans certains rejets d'amiante du Québec et Ie degré d'activation dépend de la provenance.vIntroductionOn sait depuis longtemps que la serpentine, Mg3Si2O5(OH)4, un silicate hydroxylé de magnésium, devient amorphe lorsqu'elle perd de I'eau d'hydratation entre 600 et 700 °C. La serpentine ainsi calcinée est alors dissociée en magnésie et en silice. Cette magnésie, dite active, est soluble dans un acide faible ou même dans les solutions de sels d'ammonium.Plusieurs precédés chimiques ont été proposés afin d'extraire sous forme de composés magnésiens la magnésie de la serpentine. La plupart de ces procédés comportent une activation par calcination de la serpentine préalablement à une Iixiviation par un acide ou par une solution d'un sel d'ammonium.Malgré la contamination par Ie fer et par d'autres éléments, les compositions chimiques des rejets de différentes mines d 'amiante du Québec, présentées au tableau 1, sont très proches de la serpentine typique. Puisque Ie degré d'activation de la magnésie varie grandement d'une serpentine à I'autre lors de la calcination, la première étape de la recherche sur la transformation chimique des rejets d'amiante du Québec se résume à une étude de leurs comportements thermochimiques."

Jan 1, 1982

By G. S. Hume

In the transformation of carbonaceous materials, such as peat, to coals of various grades, the changes are known to be both physical and chemical and the grade of coal finally produced depends on the stage to which alteration proceeded. Those changes, which are frequently spoken of as the results of metamorphism, are due to pressure with accompanying heat and, according to the amount of metamorphism to which the sediments with the included carbonaceous beds have been subjected, there is a gradation from peat to anthracite coal, and even to graphite. The improvement in the quality of the coal as a result of metamorphism is due to an increase of the carbon content of the coal and a corresponding loss of the volatile materials. This rise in the quality of the coal according to the degree of metamorphism is well illustrated by the coals of western Canada. In the Plains area, where the deformation and the attendant metamorphism of the sediments is comparatively small, the coals are lignites, whereas in the mountains, where deformation has been severe, the coals are semi-anthracites. Sub-bituminous and bituminous coals occur in the intervening areas. The same general relationship between the quality of the coal and the degree of metamorphism holds true for the Appalachian basin of the United States, where there is a progressive improvement in the quality of the coals from west to east, that is, from an area of comparatively slight metamorphism to an area of marked deformation in the Appalachian Mountain region. But while it is true that this relationship holds in a general way, it has been found that the improvement in the quality of the coal is not always uniformly progressive, and there may be local variations such that an area containing coal with a carbon content indicating low or medium metamorphism may be surrounded by areas in which the coals are of higher grade. These local variations in many cases can be explained, and they in no way detract from the general rule that, in a region exhibiting a progressive betterment in the quality of the coal from an area of low metamorphism to one of more marked deformation, the quality of the coal, i.e., the amount of fixed carbon in the coal, may be taken as an index of the degree of metamorphism of the coal as well as of the sediments in which it occurs, It has been pointed out (') that certain coals, such as cannels, are unreliable indicators of the varying degree of metamorphism because of the nature of the material from which such coal was derived. Such coals, however, are not known in western Canada and their behaviour need not here be discussed.

Jan 1, 1927

By The Staff

"THE property of Red Mountain Mines Limited is located 11/2 miles north and west of the town of Rossland, in southern British Columbia. The mine is situated on the flank of Red mountain, famous in pioneer days as the site of a number of profitable gold-copper producers. Mining and milling commenced in May, 1966, and by the first of July the concentrator was treating close to its average design capacity of 400 tons per day. The following description of the property and its operations is divided into three parts, dealing respectively with geology, mining and milling.GeologyAll the known ore reserves of Red Mountain Mines occur on the Coxey claim, on the west slope of Red mountain. Although there are indications of molybdenite mineralization elsewhere on the Company's property, these have not been developed.The Coxey and adjoining areas are underlain by the Mount Roberts formation of the Rossland volca-nics. This formation consists of an interbedded series of volcanic and sedimentary rocks, mostly brecciated and silicified near the ore zone, and all intruded by igneous rocks which occur in various forms, and vary in composition from basic to acid. The country rock in the vicinity of the mineralization seems to be mostly a volcanic, approximately andesitic in composition, and possibly a surface flow. There is much banding, some of which is undoubtedly due to tuff and agglomerate layers, and some to narrow, siliceous, sedimentary horizons such as the surface exposure of the main ""A"" orebody, much of which was a thin capping of greyish banded rock that looked like quartzite. The drill holes also intersected occasional layers of black, argillaceous quartzite, sometimes altered to a greenish colour. The whole assemblage has been silicified with varied intensity, sometimes to such an extent as to have obscured or obliterated the original characteristics. The mineralized zone has also been strongly brecciated, the fragments varying in size from less than an inch up to large masses, best described as a mega-breccia. Anomalous results obtained in drilling, such as sedimentary sections that do not appear in adjoining holes, may sometimes be due to the presence of these large blocks, no longer in their original position. The whole volcanic unit is thus very complex and confusing. For practical purposes, the ore may be said to occur in a greenstone formation with minor sedimentary interbeds and considerable later igneous material."

Jan 1, 1967

By D. E. Smith, M. K. Murthy

"The commercial potential of a silica-kaolin deposit that occurs on the banks of and close to the Missinaibi River in the District of Cochrane, Ontario, is under evaluation by Algocen Mines Limited. The geological features of the deposit, as well as its probable origin, are described. Mineralogical analysis of the deposit samples indicates that the principal minerals are quartz and kaolinite clay; it is estimated that about 20 per cent of the deposit is kaolin clay. The impurity minerals present are: a slightly magnetic Fe-Ti oxide mineral, goethite, muscovite mica, tour-maline, staurolite, anatase and zircon. Laboratory research studies are in progress to develop and evaluate suit-able methods for the separation of silica sand from kaolin. Results to date indicate that good-quality silica sand with an Fe,03 content in the range of 0.012 to 0.025 per cent can be produced. It appears that the clay portion can also be beneficiated to yield products meeting commercial requirements. It has been possible to beneficiate a portion of theetlay to obtain the particle size distribution now specified by industry. However, research is continuing to develop suitable separation and beneficiation methods which can produce kaolin clay meeting all the commercial requirements."

Jan 1, 1970

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

By Alex Rown

"THE SYDNEY COAL FIELD has long been afflicted by high costs and low productivities. However, a distinct possibility now exists that improvements can be made in costs, productivities and revenues. If these hopes materialize, the Sydney coal field will once again be regarded as a valuable asset in our national inventory of energy and metallurgical coals. The economic possibilities for the Sydney collieries depend on performance at the pits and in the market place. Because this audience is already well informed about colliery planning, I would like to start with an assessment of the modern coal market insofar as it may relate to the Sydney field. Since 1950 we have seen a vast growth in the population and industrial empires of the western world which has resulted in an enormous and escalating demand for energy. If the energy supply pattern of the first 50 years of this century had been followed, this would have led to an immense demand for coal."

Jan 1, 1972

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By M. A. Marois

This paper proposes an improved temporal stability condition for the implementation of an inverse heat transfer method for predicting the time-varying bank thickness of the phase change protective bank inside a high temperature furnace. The direct problem is handled with the enthalpy method. The inverse method rests on the Adjoint Problem and the Conjugate Gradient Method. It is shown that the temporal stability condition for the inverse phase change problem relies on the time delay of the temperature measurements. Results indicate that this time delay is proportional to the heat diffusion time including heat diffusion through the mushy zone.

Jan 1, 2011

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By Robert B. Parsons

"Once all the hullabaloo about Finance Minister Wilson's April 27 budget died down (or was it an April 26 budget?), the pain of the budget papers began to sink in. Individuals and corporations will have to dig deeper and pay more taxes - and government will continue to dig deeper and spend more. The irony of the situation is that higher tax rates actually make flow-through shares more attractive as a tax-deferral investment - a bittersweet ""bravo"" for the mining industry.INTRODUCTIONFor the first time in Canadian history, a major budget address has taken two days to deliver. Of course, it's not a case of long-windedness, but rather a case of a hastily called press announcement on April 26 in response to a budget leak, followed by a formal budget speech on April 27.The general reaction of the business community to the budget was to the effect that the tax hikes are acceptable, but the government's failure to curb spending is less than acceptable. Mr. Wilson's reported response indicated that the government had never promised to cut spending, and that increased government spending would actually benefit the country. That age-old debate will doubtlessly continue for generations.In any event, three noteworthy components of the budget papers are:• Personal income tax rates increase effective July I, 1989;• A ""large corporations tax"" (in effect 'a corporate ""minimum tax"") is effective July I, 1989; and• Federal sales tax increases are effective from June 30, 1989, to be replaced by a national sales tax in 1991.A brief overview of these and other budget proposals follows."

Jan 1, 1989

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

By C. Cristonffanini, S. Nazari

"In the past, simulation was considered to be an offline tool disconnected from plant operation. Advancements in the computation power combined with utilizing physics and chemistry sciences have allowed us to significantly improve the modeling and simulation technology for mining and mineral processing. This paper investigates the benefits of first principle models and simulation by connecting them to real time operation. Process data are connected to high fidelity models executed in parallel to the operation. In recent literature, this concept is known as Digital Twins. The Digital Twin is used for various purposes such as optimization, virtual instrumentation and condition monitoring. Using IDEAS™ simulation software we are able to construct a digital twin for different equipment inside a mineral processing plant. Two case studies for building a digital twin for the primary hydrocyclone feed pump and thickener underflow are presented. Using the pump’s model, a digital twin is developed and is installed in a gold extraction plant that is able to infer the slurry density in real time. Additionally, it is used for detecting sanding in the pipes and impeller condition monitoring.INTRODUCTION Since the eighties, thanks to advances in computation technologies, computer based simulation of processes using first principle models has become a well-known engineering tool for various industries. As our understanding of processes has increased, their representative models have become more realistic and more sophisticated. Due to this increase of accuracy, use of simulation is becoming more fundamental in process industries. The main goals to use accurate simulation is to decrease the engineering and construction cost, optimize the process design and improve the operation performance by decreasing operation cost and increasing efficiency. The term Digital Twin was first introduced in 2010 by NASA (Shafto et al., 2012) in aerospace industry. Subsequently, the concept quickly spread through other industries. As of today, no standard organization has provided an official and unique definition of Digital Twin for process industries. However, there are three important aspects that are common throughout various descriptions. When simulation is core functionality of the process (1) along the entire life cycle of the plant (2) with direct linkage to operation (3), it is called that process has a Digital Twin. According to Gartner, the concept of Digital Twin has elected as fourth most important disruptive technology for the year 2018 (https://www.gartner.com/, 2017)."

Jan 1, 2019