Search Documents

By J Bohm, B Csoke, I Tarjan

In process technology, especially in coal preparation, it is often necessary to have a continuous knowledge of the average density of granular material in order to achieve both quality control and process control. The paper presents a new method and means supported by laboratory measurements for the rapid, practically continuous, determination of the average density of continuously supplied granular material through frequent sampling.

Jan 1, 1993

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

By Waterhouse BJ

Occurrence data of Tastubian,Sterlitamakian, and Aktastinian (all of Sakmarian Stage of Early Permian) brachiopod genera are analysed by Q-mode cluster analysis, principal component analysis, and discriminant analysis based on presence or absence of genera. Five faunal provinces and their corresponding generic associations persisted throughout the Sakmarian Stage. The additional Sasian Province incorporating the Lhasa and Shan-Thai terranes became recognisable in Sterlitarakian and strengthened in òAktastinian, implying a Tastubian-Sterlitamakian rifting event, followed by subsequent northward drift and divergence from Gondwana, and convergence with Laurasia. The nature of Permian 'Tethys' is discussed on the basis of faunal migration and abrupt changes of faunal provinciality in Lhasa and Shan-Thai terranes.

Jan 1, 1990

By S C. Dominy

A high nugget effect and the presence of coarse gold characterises many vein-gold deposits. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold. Geological complexity often compounds this effect. Underground development, in-fill drilling and bulk sampling/trial mining are often required to delineate Ore Reserves. Winzing is an historical technique that was used to gather geological and sampling data during underground exploration. It permits access to the mineralised structure below the current datum to help determine viability. Winzing has always been considered an arduous and dangerous task. Modern technology has led to the development of the Mobile Supersucker, essentially a giant vacuum cleaner. This system permits safe and efficient winzing activities, and allows the collection of bulk samples for grade estimation. Bulk samples from horizontal development have long been collected to help define mineable grade. However, when defining blocks below current development, there has been over-reliance on ineffective æsmall sampleÆ drill data. The Mobile Supersucker permits safe and cost-effective development of winzes and off-winze sublevels.

Jan 1, 2003

The use of coal as a fuel for heat and power generation has a long history. During the nineteenth century most of the present combus- tion technologies were pioneered, as shown in Table 1, This period was associated with the "golden age" of coal and its contribution of almost 80% of the world's energy demands in the early,1900s . The decline in the use of coal has been due to the transfer of the heavy transportation area to diesel power, the elimination of coal as a household fuel and the substitution of oil for coal in power plants. Coal remains the major fuel for the electric utility industry and the present paper will be concerned primarily with that application. Table 1 outlines the development of coal tech- nology with the parallel understanding of coal as a material and its behaviour during combus- tion. Clearly many developments in combustion technology have occurred in this century, although most of the processes had been invented in the nineteenth century. Also, the great expanse in coal research of the past few decades has led to a greater understanding of the coal combustion process.

Jan 1, 1987

By S R. Grano, J Duan, T A, D Fornasiero

We have determined the experimental rate constants for chalcopyrite particles floated from a complex sulfide ore and compared them with those calculated using a recently developed flotation model. The model incorporates contributions from the efficiencies of collision, attachment and stability between particles and bubbles, as well as their frequency of collision. For these calculations, the contact angle of the chalcopyrite particles in the ore was obtained independently using a surface spectroscopic approach. The calculated flotation rate constants were in good agreement with the experimental data and able to reproduce the characteristic maximum in flotation rate constant for particles of intermediate size. The values of bubble velocity and turbulent dissipation energy derived from these calculations are relatively low and may well correspond to mean values of these parameters inside the flotation cell. We have extended this approach through the application of a property based model to an operating plant, with a satisfactory outcome.

Jan 1, 2005

By K Hooper

Over the past 20 to 30 years statistics as a science has grown in significance. Not a day passes without reference to the latest statistics by the print, audio and audio-visual media. The Northern Territory Government has been part of this growth and like other public and private sector organisations collects a broad range of statistics. The Northern Territory Department of Mines and Energy participates in the government's statistics collection process. Statistics collected and published by the Department of Mines and Energy include geoscientific; mining and exploration tenure; environmental (e.g. mine site waste water management); production of minerals, oil and gas; mining sector employment; and occupational health and safety. The importance of statistics collection to the Northern Territory Government is discussed in the paper.

Jan 1, 1994

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management.

Jan 1, 1995

By Grant J

In surface mining, significant improvements in efficiency can be obtained through greater control over the formation of the muckpile. By tailoring the muckpile shape and its looseness to the requirements of the excavating equipment savings can be rea- lised through increased production, machine life and reduced maintenance. For instance, one open cut coal mine has recently estimated that a 2001o improvement in its front row throw would realise $320,000/year savings in rehandle costs alone. Previously greater throw has been achieved by increasing the powder factor through increased quantity of explosive or by drill- ing a larger number of holes-both at a significant cost penalty. However a recent series of experimental blasts demonstrated that it was possible to achieve a twofold increase in the distance of throw of a single row blast by simply changing delay timing alone. The Nobel Electronic Delay Detonator was used to provide the timing flexibility and control required for a thorough study of the effect of blast timing on heave. Whilst it is well accepted that the front row of a blast dominates the extent of throw, it was also found that the profile of the blast could be significantly altered. To date, the general consensus has been that the muckpile for- mation from a blast is a function of the blast geometry, the rock type, the explosive and the initiation sequence. Typically the geometry, rock type and initiation system have a far greater impact than the explosive type. This has been demonstrated by many high speed film studies. However the extent of influence via initiation has rarely been fully evaluated, owing largely to the limited control offered by conventional detonators.

Jan 1, 1988

By Wingham DW

Based upon the previous work of Norman and Loeb, a method, was used, to assess-the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa. The materials to be tested were obtained in the form of large diameter balls and were run, along with the regular ball charge, in a large ball mill operating-under normal grinding conditions. At selected. intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.

Jan 1, 1963

The capacity of chlorine based solutions to rapidly and effectively dissolve coarse gold in oxide ores is well established. The inherent advantages of chlorine are high dissolution rates (10 - 100 times those of cyanide), and low cost. The high dissolution rates mean that coarse or poorly liberated gold may be dissolved over relatively short periods and hence ore particle size may cease to be such a critical factor. The cost of size reduction to allow adequate gold liberation in order to achieve an adequate gold recovery is less of a consideration when using chlorine than in traditional plant or heap leaching cyanide-based treatment systems.Because chlorine based solutions capable of dissolving gold evolve an unpleasant vapour phase with the potential for significant chlorine losses into the atmosphere, traditional heap leaching with active solutions being sprayed onto prepared heaps is not possible. The ore must be covered and the solution may be introduced beneath that cover through prepared injection `wells' and recovered through production 'wells'. The pit is flooded with active solution beneath an overburden or cover with the solution migrating from the injection 'wells' to the production 'wells' over a period of around five - ten days.

Jan 1, 1992

Construction of Western Mining Corporation's nickel refinery at Kwinana, Western Australia, commenced in July, 1968. Production of 15,000 tons per annum of refined nickel metal will commence early in 1970, The plant will also produce approx- imately 150,000 tons of ammonium sulphate0 The ammonia leach process which was developed by Sherritt Gordon Mines Ltd., and has been in operation at their plant at Fort Saskatchewan, Alberta, Canada, for the past 15 years, will be used at Kwinana. The refinery will cost approximately 435 million, and will employ upwards of 250 people.

Jan 1, 1969

By Fowke NC, Williams RJ, Hungerford F

In-seam, directional drilling has been implemented at Huntly West Mine, New Zealand as the most cost effective means of obtaining geological information at a level of detail and accuracy required for planning of longwall ("flexiwall") panels. No geological or geophysical technique tried at the mine prior to 1989 has been able to reduce geological risk to an acceptable level. Surface and in-seam seismic methods have not had adequate resolution. Obtaining the required knowledge via surface drilling would be prohibitively costly, and still not precisely locate or orient faults or the axes of seam "ridges and valleys".A total of 3543 m was drilled at an average of 67m/shift including setting up time. Unplanned delays totalled only 9.6 percent. Major re-interpretation of seam structure resulted from the drilling. Lateral and longitudinal panel grades have been defined. which should be negotiable with the Coalcorp longwall equipment.

Jan 1, 1991

By T GRAHAM-TAYLOR

A trend towards mining more complex and economically marginal orebodies, often combined with increasingly tight product specifications, increases the number of variables which need to be considered in production scheduling. Linear programming incorporating integer constraints can be used to create production schedules which are practical as well as mathematically optimum. Factors which can be taken into account include variability in product stockpiles, targets for head or product grades, production of different material types, production from different areas, production targets for loaders, and dependencies between mining blocks. For each schedule an appropriate objective for optimisation must be chosen. Examples of objectives are: to minimise or maximise grade variation; to minimise waste movement; and to minimise movement by front end loaders. A staged approach to the implementation of computer systems based on linear programming optimisation is Proposed.

Jan 1, 1992

Within the Business Process Improvement Program initiated at Placer Dome during 2003 was the Business Performance Management Project (BPM).BPMÆ s aim has been to extract productivity improvements from individual business units by providing a model for implementing leading practice based management process within the Placer Dome Group, sharing management best practice, injecting new management techniques and instilling a continuous improvement culture. The installation of an underground dispatch system has been a key component of the BPM project at Osborne Mine.Information capture and analysis allows for corrective action to be planned and executed before there is a material impact on the performance of a business unit. This paper briefly describes the principles and practices of effective business performance management, the four processes of a management operating system namely; strategic and tactical planning, implementation and reporting. The identification of business drivers, their measures and associated key performance indicators is discussed. The benefits of an underground dispatch system at Osborne with respect to safety, production and maintenance is described along with the installation process within the mining department that included its configuration, resourcing and roll out.

Jan 1, 2005

By Q Zhou, Y Ma, J Zhu, R L. Frost, P Yuan

A series of organoclays with different surfactant arrangements were prepared by ion exchange. The resulting organoclays were investigated using a combination of characterisation techniques, including X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric measurement (TG) and N2 adsorption-desorption. In the present study, the pores within the organoclays were discussed on the basis of the micro- structural parameters, including BET-N2 surface area, pore volume, pore size, surfactant loading and distribution. The results show that both BET-N2 surface area and pore volume decrease from low to high packing density of the surfactant as the average pore size increases. Two basic organoclay models were proposed for hexadecyltrimethyl- ammonium bromide (HDTMAB) modified montmorillonites: 1. the surfactant mainly occupied the clay interlayer, and2. both the clay interlayer space and external surface were modified by surfactant. This study demonstrates that the pore structure of the resulting organoclays has a significant influence on the sorption efficiency and mechanism of p-nitrophenol onto the organoclays.

Jan 1, 2008

By Heinrich CA, Wall VJ, Walshe JL

The Porgera Gold Mine, located in the highlands of Papua New Guinea, has produced over 5 million ounces of Au, since its opening in late 1990. The deposit is located within Upper Cretaceous Papuan Platform sediments approximately 25 km south of the Lagaip Fault, and is spatially and temporally associated with the 6 Ma alkaline Porgera Intrusive Complex.

Jan 1, 1995

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The use of concentrated solar flux for high temperature metallurgical applications is a wellresearched area with several reported literatures on solar calcination and metal oxide reduction. This paper presents two such processes with potential to reduce the carbon footprint from ironmaking through using concentrated solar flux. The first process involves solar flux incorporation to the recently developed lime-magnetite pellet (LMP) route of magnetite ore agglomeration. The second process is a hybrid solar-smelting route for iron ore-coal composite pellets that utilises solar flux to provide process heat. Both the concepts of solar agglomeration and solar smelting process were investigated using a solar simulator-hybrid reactor set-up at Swinburne University of Technology. Results from solar agglomeration experiments at 950°C suggested no change in the reaction mechanism of the LMPs under solar irradiation compared to electrical heating. The percentage and morphology of the primary phases (mainly CaFe3O5) appeared similar for both solar and electric heated LMPs. The solar-smelting of magnetite concentrate-lignite coal composite pellets at 1130°C showed a maximum metallisation of 55 per cent after 1.5 hrs of reaction. The solar-smelt process has about 25 to 35 per cent lower CO2 emission compared to the blast furnace ironmaking. Technoeconomic analysis of implementing a CST facility in an existing composite pellet process suggested a payback period of about ten years at a heliostat cost of $A100/m2 and natural gas cost of A$10/GJ. The economics of CST implementation can be further enhanced by decreasing the thermal losses from the heliostat field and reactor.

Nov 8, 2021

Where tunnel rounds are based on the burn cut, faster advance could often be achieved by increasing blasthole diameter from (the conventional)

Jan 1, 1981

Within the Ross River Basin, the following types of water were collected and analysed; 19 streams, 24 wells and bores together with 19 samples from the Ross River Dam. The waters were found to contain up to 269 ppm of silica and, although they meet the requirements for industry in all other respects, this extremely high figure means that two basic guidelines should be followed. All steam generation units, except those less than 150 psi should employ hot lime zeolite softening, demineralization or evaporation to remove silica. Cooling systems should only operate on a once through basis.

Jan 1, 1978