Search Documents

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

By G P. F Chitombo

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have been identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

Palaeostress analyses of the northeast-dipping Koki Fault Zone demonstrates in the hanging wall an east-west compressive stress and sinistral reverse-slip. Data from the footwall region are more uncertain and may relate to rotation of the stress field during fault motion. The fault-plane solution of the 1979 Port Moresby earthquake (Modified Mercalli Intensity 5-7 at epicentre 70 km east of Port Moresby) shows east-west compression and a stress field identi

Jan 1, 1997

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

The rapid industrialisation of the world was driven by an improved ability to utilise chemical energy. Unfortunately harnessing explosive energy did not come cheaply given the hundreds of lost lives. However, the modem explosives industry has made significant technological achievements, for explosives are now considered to be both safe and extremely effective. Upon closer inspection, it would appear the key to this achievement has been the development of initiation systems. While the focus may have been originally on safety, modem developments have concentrated upon harnessing the benefits of initiation control. Before attempting to gaze into the future, it is worth reviewing some of the significant advances that have occurred.

Jan 1, 1990

By Matthew I. G, Hall P. G

The Selective Precipitation (Basics) Process is a means of controlling impurities such as the ions of Mn, Mg, and Cl as well as sulphate and water, in an electrolytic zinc plant circuit. This is achieved by precipita- ting zinc selectively as a basic zinc sulphate from a portion of impure circuit solution. The impurities remain in the solution, which can be discarded, while the zinc, substantially free of impurities, is returned to the main circuit by using the precipitate as a neutral- ising reagent. A description of the process and its development to a full scale operating plant at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited is Presented.

Jan 1, 1977

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

The use of the heavy media cyclone (HMC) Separation process for the treatment of ores in a particular size range is comparatively new to Australia. The paper describes briefly the principles of HMC operation. Reference is made to early development work, the pilot plant trials and the acceptance of the technique as a mineral dressing process. The Mitchell Cotts pilot plant at Amdel is described briefly and the results of test work on this unit for the processing of a wide variety of ores and ore types are given. Comments are made on the ob- jectives aimed at in the investigation and results are discussed with particular reference to behaviourial differences between ore types. The process is easy to operate, possesses a high capacity-to-unit-size rating and is capable of a high degree of flexibility. Further developments such as specially prepared and graded media for specific applications, automatic media density control and regulation of media consistency by the use of surface ac- tive agents and polymers have increased versa- tility and sensitivity of control to the point where products differing by as little as 0.02 of a specific gravity unit can now be separated with ease.

Jan 1, 1973

In June 1992, the High Court of Australia recognised native title of the Meriam people over parts of the Mer Island in the Torres Strait as a form of common law. The Court also indicated that native title may have survived European settlement of the mainland Australia where it had not been extinguished by Governments and Aboriginal people have maintained their traditional connection with the land. The decision meant that two systems of land law were seen as existing side by side in Australia: ò one which derived from grants from the Crown under laws passed by Parliament; ò another which derived from the diverse laws and customs of the many Aboriginal groups in Australia.

Jan 1, 1996

By Wright D. C

The operation of the cyanide-sensitive Mintek/TB1 kegold electrode was studied in the laboratory, with regard to equilibration time and drift, the effects of pH, stirring, salinity, dissolved oxygen, zinc and copper(I) ions. Methods for valid calibration in the range 20-600 mg(NaCN)/L and pH values in the range 9 - 12 in the absence of copper were also studied. Increasing the salinity beyond a threshold of 40 g(NaCI)/L improves calibration and measurement. The sensitivity is 91 mV per decade change in the concentration of ionic cyanide, and output is reproducible to within 10 mV with attention to the factors listed above. However, salinity of 40 g(NaCI)/L also sensitises the electrode to interference by copper(1) ions. This copper sensitivity seems capable of saturation, suggesting a research strategy for possible remedies.

Jan 1, 1996

By Wiltshire PG

The process uses sodium hydroxide and sodium nitrate reagents as in conventional Harris refining plants, selectively removing the arsenic to the caustic phase at an operating temperature of 420-450¦C. A novel feature of the process concept is continuous treatment of loaded caustic slag for recovery of arsenic as a sandy crystal product suitable for further processing to arsenic trioxide. A large pilot plant was constructed and operated over a period of 3 years to develop materials handling techniques and equipment components and to prove the concept. Stable operations were achieved at equivalent capacities of 200 tonne/yr arsenic removal. The process is being considered in plans for expansion of bullion softening capacity at Port Pirie.

Jan 1, 1984

Electron paramagnetic resonance provides a fast method to characterise quartz. Quartz from veins associated with the Cambrian massive sulphide deposits in the Mt Read Volcanics of western Tasmania and from Devonian reefs associated with gold mineralisa- tion at various localities in Tasmania exhibit specific EPR patterns, different from quartz from common veins. The intensity of the EPR spectra of the quartz can be used as a statistical guide to gold mineralisation at Beaconsfield.

Jan 1, 1987

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

By D R Van Eck

Western Deep Levels, a seismically active deep level told mine. stalled placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to he extent where installation of mechanical and hydraulic jacks could he Eliminated

Jan 1, 1998

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

By Bearman R. A, Parkin R. M

Traditional quality control procedures for aggregates production within the quarry industry rely on off-line laboratory analysis, resulting in poor performance and inconsistent product quality. A high speed on-line aggregate classification system is described here. A product sampling system directs aggregate through an inspection chamber where a novel imaging system digitises the particle geometry. Data processing algorithms extract dimensional data and image features, while a neural network classifier assigns a qualitative shape descriptor to each rock particle. This system provides each sampled batch with a complete analysis of size and shape distributions, complementing a new generation of cone crusher technology to maximise product quality and plant efficiency.

Jan 1, 1995

Intermontane valleys form unusual features of compressive mountain belts both in the sharp topographic break they represent and in the strike-slip displacements often associated with the valleys. Such strike-slip motion seems hard to reconcile in the actively deforming Andes where reconstructions have indicated nearly perpendicular Cenozoic plate convergence. Detailed study of a part of the Argentine Andes between latitude 31-33¦S suggests that, although strike-slip displacements may have largely created a prominent intermontane valley system, no Holocene strike-slip displacements are observed amid the relatively active compressional deformation along the mountain belt flanks. New plate reconstructions, treating the Nazca plate as two microplates separated by fractures along the Nazca Ridge, predict large components of strike-slip motion between the South American and Nazca Plates for the period from 10 to 5 Ma. These reconstructed plate motions are consistent with strains derived from recent kinematic analyses of minor faults along the southeast margin of the Puna plateau and the general timing of tectonic phases in the Andes.

Jan 1, 1987

By D L. Richardson, B Tiedt, C D. Morgan

Following residentsÆ concerns that the ongoing operations of Collinsville Coal (CCP) mine may be resulting in the release of contaminants, including products of acid mine drainage (AMD), into downstream environments, the Queensland Environmental Protection Agency (QEPA) issued CCP with a Notice to Conduct or Commission an Environmental Evaluation at Three Mile Creek. A key objective of the Environmental Evaluation was to assess the extent and magnitude of impacts to aquatic communities and their habitats. A multidisciplinary investigation examined a suite of physical, chemical and biological indicators to meet this objective. The study also aimed to identify contaminants of concern and the location of potential pollutant sources. Potential indicators of AMD, including elevated dissolved solids concentrations and low pH, were evident within the mine lease. However, significant differences in concentration of these indicators upstream and downstream of the confluence with Three Mile Creek were not observed. Although only proxy indicators of AMD contamination, these results suggest that the extent of impacts downstream is minimal. For the purpose of this study, physio-chemical indicators were selected on the basis of those best likely to provide an understanding of the likelihood of contamination, within the constraints of readily available long-term monitoring data. Ecosystem health indicators were adopted to supplement the existing data set and provide a more æroundedÆ perspective of water quality attributes within the system, generally unattainable by standard physio-chemical assessments. In contrast to AMD products, sediments were considered more likely to have a widespread impact on aquatic ecosystems. Waterways throughout the study region, including those unaffected by mining, have been affected by broad-scale sedimentation and were typically highly turbid. Due to the many diffuse sources of sediment potentially liberated within the catchment, the contribution of the mine compared to other land uses on total sediment loads entering streams is difficult to determine. This is clearly a major management issue for mines throughout the Bowen Basin. Streams of the central Queensland region display enormous variability in water flows and physio-chemical characteristics over a range of spatial and temporal scales. This variability presents major difficulties in distinguishing anthropogenic impacts from natural variability (noise). Despite this variability, impact monitoring by mines in the central Queensland district has tended to focus almost entirely upon physio-chemical indicators. The results of the present study indicate that a multiple indicator approach to environmental assessment is more useful for separating mine related impacts from natural ænoiseÆ and impacts from other land uses. In the absence of such information, by adopting the precautionary principle of Ecologically Sustainable Development (ESD), there is potential for an environmental impact to be incorrectly attributed to mining when other activities in the catchment may be contributing to changes in stream æhealthÆ.

Jan 1, 2003