Search Documents

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

The reliable estimation of ore reserves in mineral sand deposits depends on drilling methods and assay techniques that have been specially developed within the industry. Improvement of these techniques is a continuing process, as variations within and between deposits are highlighted during the actual mining operation. Constant monitoring of metallurgical losses along with mineral production allows comparison of mineral tonnages accounted for by mining, with original calculated reserves. A review of ore reserves in the Jerusalem Creek field from scout drilling in the sixties, through mining in the seventies, shows the progression from understatement prior to mining, to the present when more than two thirds of the reserves have been depleted.

Jan 1, 1979

By Kam KM, Tran B

Statistical techniques of Box and Jenkins (1976) have been used to assess the existing control schemes and determine the dynamics of flash smelting furnace at the Kalgoorlie Nickel Smelter. Pertinent process variables, such as, oxygen flow, flux flow, matte grade and iron to silica ratio in slag, were considered in the analysis using routine operating data collected over two periods of operation. Results indicate inadequate control of some of the important variables. Dynamic characteristic parameters (dead time and response time) between a set of input and output variables were identified to improve optimisation of the existing thermodynamic model used for flash furnace control.

Jan 1, 1996

By Gillies A. D S, Lee A. H

The major operational objectives of a mine water resource management system (WRMS) are to supply the water needs of the mine and mill, to minimise disturbance to mining due to rainfall flooding or seepage and to dispose of excess water. Historically, company management have placed a significantly lower emphasis on managing the WRMS as compared to managing production. Changing Government legislation concerned with the disposal of water from mine sites is, in many cases making mining companies look more closely at how they manage their water. For example, within the next few years it is likely that prior to mining approval by the Government, mining operations will have to submit water management plans/budgets and contingency strategies in addition to operational plans. While the formulation of a comprehensive water management plan/budget is an additional cost to the company at the mine establishment stage, such plans can be beneficial to the operation in the longer term.The two keys for the efficient design, operation and development of a WRMS are the establishment of written goals which have managerial priority and secondly, access to appropriate good quality data. Managerial priority towards the WRMS will increase as a consequence of the education of mine operators in the benefits to the operation of good WRMS management or less desirably as a requirement to meet Government legislation. The collection of appropriate WRMS data is a more complex issue and to obtain information efficiently and cost effectively relies on the clear definition of the data application.

Jan 1, 1992

Revegetation at Perseverance Mining's Nagambie Gold Project is an excellent example of cost effective revegetation in the Central Victorian Goldfields. Work has centred on waste rock dumps, vegetative screens, amenity planting and revegetation trials on cyanide heap leach pads. A wetland is under construction and in consultation with farmers, waste heaps were planted with perennial pasture species.The area treated to date is 18 hectares comprising: 16 hectares of pasture and two hectares of trees/understory. Direct seeding and tubestock planting has cost $16,464. Cost effective revegetation demands careful planning from the EES stage onwards. The Government agreed rehabilitation plan should be comprehensive, realistic and above all flexible. This document must be kept in mind during the mining operation.

Jan 1, 1992

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987

In July 1994 the Premier, John Fahey MP, announced that the New South Wales Government would make available a total of $40 million over six years in new funding for the Department of Mineral Resources. These funds are to be applied directly to the generation of regional geological and geophysical information. The Government's initiative known as `Discovery 2000', is aimed at providing a major boost to the exploration industry. The Government expects new discoveries to be made and new mines to be developed because of the initiative and, perhaps, the first ever commercial oil or gas production in New South Wales. The Government's return will come from increased economic activity, and from the increased royalty return from higher levels of production. Quality information is the key to successful exploration. In the highly competitive business of mineral and petroleum exploration high quality regional geological and geophysical information improve both the efficiency and effectiveness of the area selection or project generation process. Using the `needle in the hay stack' analogy, Discovery 2000 will vastly improve industry's chances of finding the haystacks. It is up to the mineral and petroleum industries to find their respective `needles'. Careful target area selection is probably the most critical factor in mineral exploration. The ability to select the most prospective areas, or to identify prospectivity that others have failed to recognise, can make all the difference between success and failure. Government geological surveys clearly have a crucial role to play in providing the geoscientific information infrastructure that companies must have if they are to make the discoveries this country needs to pay its way in the world. It is the regional information generated by Governments that sets the scene for efficient exploration. This regional information includes regional aeromagnetics and radiometrics and gravity, regional geological mapping and tectonic analysis, and geoscientific databases. The New South Wales Department of Mineral Resources (by various names) has been providing such information for over 100 years and has led the way in many aspects of the generation and dissemination of geological, geophysical and metallogenic Information.

Jan 1, 1995

Tin mining has taken place in the New England region of New South Wales since 1872. Until fairly recent times there was little pro- vision made for environmental protection. Mining methods,which included ground sluicing and open cutting,had considerable environmental impact. Much of the topsoil was lost and there is little vegetation on the infertile and at times toxic, subsoil. Thus much of the lands disturbed by mining have not been stabilised and are eroding, causing extensive pollution of adjacent watercourses. There are more than 1500ha of abandoned tin mine sites in the New England, representing one of the worst rehabilitation problems in New South Wales and reflecting poorly on the mining industry as a whole. Recent tin mining operations incorporate progressive rehabilitation in their mining cycle. Topsoil is stockpiled and later respread. This topsoil contains a seed source, facilitating revegetation and thus stabilisation. The tin mining industry, under considerable cost pressures at present, is seeking a cost- effective revegetation technique. Most of the mines in the New England are situated in a forest environment. Trials have been conducted in the past using exotic pasture species with limited success due to the characteristics of the subsoil. Other revege- tation trials have used pine or eucalypt tree species. The cost of these techniques is a major disadvantage. Certain acacias species were observed colonising disturbed tin mining areas on very infertile subsoils. Acacias have a number of characteristics indicating a possible applic- ations in mine rehabilitation programmes.

Jan 1, 1987

By Culshaw MG, Deaves AP, Bell FG

The accurate prediction both of the water ingress into sub-surface excavations and the nearby groundwater pressures is of fundamental importance to the control of the stability and flooding of tunnels or mines constructed below the water table. Predic- tions are usually based on laboratory and in situ permeability determinations together with observations of groundwater conditions in boreholes. Although established theoretical methods provide a basis for prediction, the actual ingress depends on many factors. The objective of this paper is to explore the geological controls on groundwater conditions, and the available methods of prediction of both groundwater flow and pressure are outlined. Salient points are emphasised by reference to a case history involving the construc- tion of a tunnel in a faulted and mixed sequence of sandstones, siltstones, shales and coals. Water ingress quantities have been monitored for a variety geological and geotechnical conditions including heavily faulted and mine disturbed ground. The overall results are discussed with reference to the relevant hydrological and geologi- cal conditions in terms of the geological structure, lithology and rockmass condition as well as the construction methods.

Jan 1, 1988

By Sturgul J. R

The South Middleback Ranges (SMR) operation involves the develop- ment of iron ore resources at the Iron Duke mine in the South Middle- back Ranges to replace the Iron Baron mine whose reserves are nearing depletion. The Iron Duke mine will be developed by contract to the stage where it can continue operation at full production when Iron Baron is closed. As part of the mine planning of the operation a GPSS computer simulation model was written to determine equipment requirements. The model simulated the operation of the mine with trucks transporting ore and waste to the appropriate destinations and producing a blended product in the stockpiles. A loader and two trucks would transport ore from the stockpiles to the crusher for one shift per day. The simulation shut the operation down at crib, morning tea, shift change and weekends, and also on the third shift each day. It also modelled operating delays. The results gave equipment operating hours and total output of each material type. The model was modified to produce different outputs from the mine and could be used to determine the most productive shift arrangement.

Jan 1, 1989

By H Rouhullahi, E B. Veshki an, R Kottnauer

The Galandrud coalfield is located approximately 20 km south from the coast of the Caspian Sea, Ruyan town, on the north slopes of the Alborz mountain range, in the elevation between 500 m (the Galand River valley) and 1350 m. For the time being, 32 coal seams (generally of small thickness û 0.8 m on average) have been recognised within the. On the other hand 72 coal banks of balanced properties have been included in reserve calculation, which means that some of the seams consist of several banks. The general dip of strata belonging to the south limb is about 30¦ to the South (with drags close to the south overthrust, where the dip reaches 85¦), while the dip of beds at the north limb is rather steep and usually between 45 to 75¦ to the North. The coal quality is in a rank of high volatile bituminous coal. The steep dip, unstable lithological development, complicated tectonics and comparatively lower coal seam thickness are the characteristic features of the Galandrud deposit. Environmental protection of this area makes exploration and exploitation more complicated. During mine exploration several adits were driven at three levels with 50 m vertical distances. About 4000 m of gates and crosscuts were up to now driven. During mining test the down-cut mining method (with one cut), the strike cut mining method and the down-cut mining method with two cuts were tested. The paper describes outlines for the selection of mining methods on the base of classification of the effective hangingwalls and footwalls, hazards of mining operations, and possibilities of the mechanised mining.

Jan 1, 2003

Structural Controls Interpretation of regional aeromagnetics, radiometrics and satellite image data has identified three structural domains (fig 2): The Fairyland Domain: a general N - S structural trend. The Cracow Domain: a general NW - SE structural trend. The Bald Mountain Domain: a general N- S structural trend. Known mineralisation is confined to the Cracow Domain in which there occurs two major NW - SE trending fault zones. The Cracow Fault Zone (CFZ) and the Immy Creek Fault Zone (ICFZ). Enhanced detail of the CFZ (fig 3) shows three main structural trends within it: NW-SE structures which include the mineralised White Hope South fault zone and the Golden Mile fault zone. NE-SW structures which have an influence on mineralisation in the Orange Creek, Fernyside and Golden Plateau areas. N-S structures comprising several major structural zones.

Jan 1, 1990

Some of the major factors affecting ore reserve estimation in gold mines are discussed together with their impact on computational methods.The major priority in ore reserve estimation is to get sampling and geological problems resolved. Poor basic information cannot be remedied by mathematical methods.Generally the more complex a deposit becomes the greater the need for subjective assessment and the less applicable are more complex ore reserve methodologies.

Jan 1, 1984

By Breen AM, Phelan JM, Doherty RJ

Early in 1990, Pancontinental Resources (Base Metals) Pty Ltd commenced flotation treatment of ore from the complex copper-lead-zinc sulphide orebody at Thalanga, 65 km west of Charters Towers in North Queensland. The orebody consists mainly of primary sulphide ore but also contains a substantial proportion of supergene ores which are being processed during the first year of operations. The supergene ores are of three main types, designated as A, B, and C. Supergene A ores are essentially copper ores, containing little lead and zinc, while B and C ores are copper-lead-zinc ores with different degrees of alteration of the original chalcopyrite and different ratios of copper to zinc content. Copper is present in the supergene ores mainly as chalcocite, digenite and covellite. Lead and zinc occur mainly as galena and sphalerite respectively. This paper describes the development of flotation plant practice, aided by laboratory testing, to process the supergene ores. The major challenge in treating these ores is that a varying proportion of the sphalerite is naturally activated and is not easily depressed in flotation by the conventional zinc depressants.

Jan 1, 1991

By Jagger ND

Pressure filters were found to be necessary to produce Elura silver/lead and zinc concentrates at sufficiently low moisture contents for bulk cargo shipment by sea to smelters.The difficulty in obtaining low moistures was due to the fine primary grind, 80% passing 45 microns, and resultant fine concentrates, 97% passing 45 microns.The filtration system was designed to filter up to 90,000 tonnes/year silver/lead concentrates and up to 130,000 tonnes/year zinc concentrates.This paper details the preliminary test work to select Larox automatic pressure filters, and the commissioning and operation of these filters to achieve design criteria for both concentrates. The design criteria for both concentrates have been bettered due to the concentrates being coarser than the design sizing.

Jan 1, 1985

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of >2000 people from their communities, the high average annual rainfall (>2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to >2000 m within 20 km of the coast, and to >3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By Sakurai F

Akita Zinc Refinery of Mitsubishi Metal Corporation (MMC) started operation in 1953 with a capacity of 560 tons of electrolytic zinc per month. Its capacity has been expanded gradually and reached 8,100 tons per month in 1973. However, present production level is about 6,500 tons per month due to the depressed zinc market. In 1963, newly developed sulphate roasting was incorporated for residue treatment. Since 1973, electric power from Ohnuma geothermal power station of MMC has been supplied in addition to hydroelectric power from Komata power station of MMC. At present, about 40% of power is supplied from our company's power station and the rest is from the power company. Recent customers' demands for zinc prod- ucts include various kinds of shape, weight and chemical composition of galvanizing zinc alloy. It is necessary for zinc producer not only to meet the requirements of customers but also to enhance the value of zinc product in order to expand the market of zinc.

Jan 1, 1987

There is a well-known saying, variously attributed to the great King Solomon and other sages of antiquity, to the effect that 'there is nothing new under the sun'. The inventive genius of man, as far as it is personified in the metallurgist, has often had the truth of this statement poignantly brought to mind when investigating the priority of ideas in its own particular branch of science. Not infrequently some operation, at first inilocently taken for a novel procedure, has later been found to have had an irrefutable precedent in the more or less remote past.When confronted by a question of this kind the metallurgist can generally much simplify his search if he at once turns his scrutinising gaze towards that ancient home of metallurgy, Germany. Vast departments of the smelting art have originated there, and even when Germany has not been in position to claim priority of invention, it has at least been characterised by a distinction equally as worthy - ie that of the faithful and authoritative exposition of the theoretical grounds on which the invention rests.In the present instance, in endeavouring to trace the history of pyritic smelting, the writer has naturally turned in the abovementioned direction, and not without some result, although the recorded data are, as might have been expected, meagre. A complete history of the art of beneflciating ores by means of fire, in all its many ramifications, still remains to be written. Possibly it may never be written, for the extent of the subject is tremendous. It is even practically impossible to clearly trace the development of one of its most modest sub-branches in satisfactory detail, or to present that branch without going to a considerable extent into related matters of a merely general character. For the purpose of dealing with the subject it will be convenient to divide it into two concurrent heads, and to distinguish, for historical reasons as well as for metallurgical ones, between that branch of the general method of matte smelting, which, until about 1891, has been called 'pyritic smelting', and the more recent offshoot of the latter, which, by distinction, may be called 'pyrite smelting'. The nature of pyritic smelting was clearly defmed by Dr John Percy in 1880, and his interpretation3 may be accepted as well known. To recall the characteristics of the method we may perhaps paraphrase Dr Percy's meaning by describing the process as a special method for the smelting of lean or dry silver or gold ores, which do not contain sufficient lead or copper for these metals to act conveniently as collectors of the precious metals. The operation is conducted in a blast furnace, with an amount of carbonaceous fuel sufficing to produce an exclusively reducing atmosphere, and with the addition of pyrites, in order to form a regulus in which the precious metals shall be concentrated, the pyrites themselves being either argentiferous, auriferous, or cupriferous, or any combination of these three, or wholly barren of metal values. In the common acceptation of the term, it is understood that the use of the reverberatory furnace is excluded.

Jan 1, 1994