Search Documents

Industry can achieve best results via thorough planning, consultatiion with agencies and local communities and a 'hands on' approach to' environmental problem solvingThe Department of Energy and Minerals, through its Minerals Group, has regulatory responsibility for the mining and extractive industries in Victoria. The role of the group is to facilitate the environmentally responsible development of these industries for the benefit of Victorians. It has a wide range of contacts with other government agencies, local government and community groups.The paper is in three parts; firstly, an overview of the nature and contribution of the mining and extractive industries in Victoria; secondly, the industries' regulatory framework; and thirdly, the environmental issues facing the industries and the management of these issues.

Jan 1, 1992

By K Heiskanen, R A. Grau

Gas velocity (Jg) measurements conducted close to the froth-pulp interface over the cross-section of a flotation cell reveal how efficiently the incoming air is being dispersed throughout the volume of the cell. Furthermore, measurements of Jg at deepest locations in the cell provide valuable information about air recirculation and dispersion conditions in the bulk volume of the cell. Gas velocity in flotation cells has predominantly been measured by a transient capture of gas in a graduated probe. In this project, a new sensor for measuring gas velocity in an on-line manner was developed. A probe is partially immersed in the flotation machine, below the froth-liquid interface. The probe is used to collect the rising air bubbles from the liquid phase. The liquid-froth interface is shifted into the probe under vacuum. A controlled vacuum is kept inside the probe. As air bubbles burst inside the probe, the excess of air is continuously removed from the probe via suction. The removed air is measured using a mass flow meter. The fully automated sensor allows us to continuously measure Jg at different location in a flotation machine. An experimental programme was carried out in a 10 cm diameter laboratory flotation column to determine the accuracy and repeatability of the automated sensor. The new sensor was used for evaluating gas dispersion conditions in a 215 litre transparent laboratory scale flotation cell. Gas velocity distributions along the radial and axial directions of the cell were measured over a wide range of operating conditions. The operating conditions in the cell were modified by altering impeller speed and air flow rate. Two different rotor-stator mechanisms were utilised to disperse the air in the cell, the MultiMix and the FreeFlow mechanism. In this paper, a description of the gas velocity sensor is given, and the results of the experimental work are discussed in detail.

Jan 1, 2005

By Armstrong AB

It has been identified that particulate matter in the form of suspended solids and bed load has the ability to adsorb heavy metals. Each year Ranger Uranium Mines Pty Ltd (RUM) identifies potential danger areas which could become major sediment sources during the wet season. Methods of suppressing sediment uptake such as hydromulching and coating areas with Poly Vinyl Acetate (PVA) glue are used. Other methods of reducing the sediment load after uptake such as diversion bunds, filters across drains, stone filters, minor sumps and settling ponds are also used. The 1983/84 wet season saw drain sediment loads reduced to acceptable levels before the water reached the outside environment. Studies to qualify and quantify flows from minor drains are still underway.

Jan 1, 1984

By Fisher AEJ

On Sunday morning 7th November, 1976, at approximately 2-25 a.m., smoke was discovered issuing from the 1912 m long belt drift at Appin Colliery. A Clouth steel cord rubber belt approximately 940 mm in width had been installed in the drift in 1963 on the basis that no fire resistant steel cord belt was then available to operate on a single lift at the load and on the 160 gradient of the drift. Investigation showed that the belt drift was on fire and the usually downcasting drift was upcasting. Immediate fire fighting and rescue operations were instituted and the drift was sealed off. High expansion foam was pushed into the drift from the surface and the fire was brought under control. Recovery work resulted in the fire being put out and the drift open for walking traffic by, S-P0 am., on Wednesday 10th November, 1976. lie experience gained during the fire fighting and recovery operations led to recommendations in regard to future use of high expansion foam.

Jan 1, 1981

By P Commander

Western Australia is a major exporter of minerals, which places significant economic and environmental responsibility on Government and the stateÆs mining industry. Moving into the 21st century, mineral production in Western Australia is $14 billion accounting for 50 per cent of the stateÆs export income. There are over 60 large-scale mining operations distributed throughout the arid regions of the state (less than 300 mm/year rainfall). There are four key mineral provinces in arid Western Australia including the Pilbara (iron ore), Murchison (gold), Northern and Southern Goldfields (gold and nickel). These provinces have significant differences, particularly in respect to groundwater demand from mining and mineral processing, aquifer systems that are utilised, and approaches to groundwater management. The arid nature of the stateÆs interior and subsequent lack of surface water resources has required substantial groundwater resource development by the mining industry. A variety of aquifers have been explored and utilised ranging from shallow alluvium and calcrete, discrete fractured zones in bedrock, concealed palaeochannels and inland sedimentary basins. Groundwater usage by the mining industry is about 150 GL/year with most abstraction related to mine dewatering, mineral processing and dust suppression. Groundwater abstraction in Western Australia is regulated by the Water and Rivers Commission. In the Goldfields, the depletion of brackish (>2000 mg/L) and saline groundwater from storage is permissible, as mining is considered the beneficial use for groundwater which may be as much as 200 000 mg/L. In contrast, the low salinity groundwater of the Murchison and Pilbara is allocated on a sustainable basis. The role of monitoring and ongoing aquifer reassessment is crucial in water management, in evaluating the condition and performance of stressed aquifer systems. Mining operations face a variety of water resource issues ranging from insufficient availability for processing to excessive mine dewatering. These issues also change as a mine operation proceeds through its development, commonly starting with a deficiency and moving into surplus as deeper pits require more dewatering. Operating mines have to contend with three main issues: water supply, wastewater disposal and contamination of local water resources. In contrast, post closure issues are related to aquifer recovery or re-establishment of groundwater equilibrium, development of pit lakes in mine voids and isolation of waste products and associated seepage or run-off.

Jan 1, 2003

By Jianmin H, Shuqin L

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed.The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by i. Dr & Prof. Beijing Graduate School, China University of Mining Science and Technology,Beijing,China 2 Northern .Jiaotong University, Beijing,China 3. Beijing Graduate School, China University of Mining, Science and Technology

Jan 1, 1992

In Munich's peculiar hydrogeological conditions (water bearing sand strata between layers of impermeable clay, silt or marl) are proper functioning groundwater lowering methods of decisive importance for underground construc- tion. Shield tunnelling with compressed air has al- ready proved to be successful. In view of growing application of shotcrete tunnelling it was obvious to consider the use of compressed air even here. After a preliminary research-project the first subway section "shotcrete under compressed air" was 1979 awarded in Munich and since that time five sections have been awarded, respectively completed. On the basis of the experiences meanwhile obtained reports will be given stating the frame conditions in which this new construction method can be applied. The tunnels consist of two shells. The outer ist driven by shotcrete under compressed air. In order to keep the air overpressure low, the groundwater often is previously detensioned or partially lowered. The inner shell of watertight concrete is built under atmosperic pressure.

Jan 1, 1987

By Corrans I. J

A wide variety of copper-bearing gold ores exist throughout the world which have yet to be processed economically for gold recovery. The copper minerals present in these ores can be many and varied and usually result in high cyanide consumptions and problematical levels of copper in leach solutions. The copper content is often assessed as being of nuisance value as the ores are generally of the grade or type which can support neither a copper project nor a straight gold project, due to the interference of copper. Many of these problematical gold-copper ores could possibly be processed economically for gold recovery using a novel ammoniacal cyanide leaching system which utilises a copper-ammonia-cyanide complex as an effective lixiviant for gold, yet limits copper dissolution and conserves cyanide. Results from recent testing have promoted a re-evaluation of the economics of treating some gold-copper ores. This paper describes the novel leaching process and discusses the conditions employed to treat a variety of gold-copper ores.

Jan 1, 1992

The ore mined from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangano-calcite and apatite. The silver content of the ore occurs in three minerals tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations.Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14 - 18 per cent lead; 3.0 - 4.5 oz silver per tonne, and 9.5 - 12.0 per cent zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from six to eight per cent lead, 1.5 oz silver per ton, 18 - 25 per cent zinc with a siliceous gangue. The common Lead Lode gangue minerals, calcite, rhodonite, bustamite - are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce:1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc concentrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufftcient granular material to be utilised as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5000 tons of crude ore per week. This plant, which operated until January 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of jigging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each consisting of two 5 ft diameter by 10ft long tube mills loaded with flint pebbles working in closed circuit with four 3 ft diameter by 3 ft wide revolving screens covered with 22mesh Toncap woven wire screen with 0.57 mm opening. Each section carried a circulating load of 28.3 tons per hour for a jig.

Jan 1, 1994

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

By L Lagoeiro

The samples studied in this paper were derived from the iron oxide facies of iron formations (IFs) of the Quadrilßtero Ferrffero, south-eastern Brazil. The rich-iron oxide varieties of the IFs can be regarded as Fe-O systems because they consist predominantly of aggregates of haematite and magnetite crystals. The study was based on carefully selected samples in which magnetite crystals occur as isolated large crystals set in a matrix of haematite grains. Optical microscopy and an electron microscope equipped with an electron backscattered diffraction (EBSD) system were used to investigate the microstructural and crystallographic relationships involved in the phase transformation between magnetite and haematite. The magnetite crystals in the IF samples are partially transformed to haematite and this process is also known as martitisation. This transformation occurs along the crystallographic planes {111} of the magnetite producing a characteristic triangular pattern of interlocking lamellae of transformed haematite crystals that are oriented parallel to octahedral plane {111}. This new generation of haematite is referred to martite because of the martitisation process. EBSD analyses show that the magnetite and the new haematite crystals, martite, share crystallographic planes of highest atomic density, eg {111} and (0001), respectively, possibly due to the ccp and hcp atomic arrangement of the two crystals. Stereographic projections of these two planes therefore coincide when the maxima of their poles are plotted. However, the crystallographic orientation of the haematite crystals in the matrix shows maxima of (0001) poles that do not coincide with those of {111} planes of magnetite. Consequently, it is concluded that the direct transformation to haematite crystals retains the crystallographic orientation memory of the former magnetite crystals, possibly due to the similar manner whereby their atoms are packed together in the crystal structures. On the other hand, no such relationships are observed between magnetite and haematite crystal in matrix. This suggests that haematite grains in the matrix may have been formed by other processes rather than those involved in the iron oxide transformation observed within the magnetite grains.

Jan 1, 2008

By Fabjanczyk MW, Nemcik JA, Matthews SM

The major strata control considerations which affect the optimisation of roadway driveage in highly stressed strata is the performance of reinforcement placed and the extent of stress induced rock deformation. High development rates and opening stability requires efficient rock reinforcement and stress relief strategies which maximise the integrity of the rock about roadways created. Current studies demonstrate the capability to reduce lateral stress distributions across panels and research is aimed toward a higher capacity bolting system. It is the intention to provide industry with more efficient reinforcement and stress control alternatives which will allow high production development equipment to operate without the restriction of delays caused by poor ground Conditions.

Jan 1, 1988

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

Over the past 15 years, Artificial Intelligence (AI) techniques have shown promise of providing the ability to capture `human intelligence' into a computer program. The sub-fields of Expert Systems and Artificial Neural Networks are finding increased use in industry to perform tasks previously considered the domain of human thinking. But, are these methods just a new type of software much like that of the past or is real magic hidden within the lines of code? Will this field continue to enjoy high growth rates and if so, what developments will we see in the near future? Which algorithms and methodologies will continue to grow? This paper discusses a number of paradigms which can be used to create successful applications. There are certain barriers; some psychological - some linked with knowledge acquisition, that must be overcome or avoided to ensure system performance. Development time also requires careful consideration before embarking on an Al project. The paper focusses on constructing goal-driven systems that transfer high-technology solutions from the research laboratory to the plant floor. Respect for system users is of paramount importance - whether their involvement is to access contained information or to participate in program maintenance as new knowledge becomes available. Examples of successful and unsuccessful AI implementation in Canadian industry and academia provide evidence of the importance of this issue. The paper also examines some current constraints on applying AI in the real-world. Among these problems are automated knowledge acquisition, methods to acquire data during run-time, real-time systems (hardware versus software), explanation and justification features and adaptive/leaning systems.

Jan 1, 1995

South Crofty's ventilation network is large and complex. Of the total exhaust air quantity 40% enters the mine by leakage routes through old workings, this air carries high concentrations of radon gas and results in the mine becoming a classified work place under the Ionising Radiation Regulations 1985. Improvements in the control of the ventilating air and dilution by increased air quantity have reduced the average contamination to aelow-0.2 WL. The major part of the radon originates from ground water inflows and from concentrations of radium within the mine with direct emanation from rock surfaces being negligible. Of 600 kBgs-1 total radon leaving the mine 93% cannot be accounted for from known and accessible sources.

Jan 1, 1988

By Anderson DR, Tassell G

A major environmental impact study carried out in the sand dunes of eastern Cape York used image analysis of remotely sensed data to both select sites for ground investigation and categorise the different ecological units present. The approach adopted was particularly suited to the type of environment in question and allowed a high degree of quantification, at a high level of confidence, at costs several orders of magnitude less than conventional Methods.

Jan 1, 1987

By Cornwell P. J

The Pajingo ore bodies consist mainly of auriferous quartz veins hosted by a suite of hydrothermally altered andesitic pyroclastics, volcanics and epiclastic sediments. Scott lode, the main economic deposit in the area, lies in a zone of major structural disruption and contortion. High grade gold and silver mineralisation is selectively mined by open pit methods. Standard grade control techniques and extraction methods were adapted to minimise mining dilution and to maximise metal recovery. Basic blending of grade ranges at the crusher has produced an average 10 gram/tonne gold head grade. The estimation of ore reserves calculated by both standard polygonal and geostatistical methods proved acceptable. Mineable reserves when compared to in pit reserves defined by blast hole drilling, indicate a decrease in tonnes and an increase in the grade resulting in an acceptable comparison of the total ounces of contained gold. The ore reconciliation of mined against milled ounces indicates that both ore reserve and grade control models underestimate the metal content in the orebody. Sampling techniques are being examined in an attempt to reduce this discrepancy.

Jan 1, 1989

By Lu S, Zhou S

The flash smelting technology employed in Jinchuan demands a better mineral processing concentrate with an MgO content below 6.5 per cent. Two ways for MgO removal have been investigated in detail based on properties and process mineralogical characteristics of the rich ores in the number one mining area in Jinchuan. The key to the first way is the use of a new flowsheet which has two-stage grinding and separation followed by single-stage regrinding and multi-stage cleaning for the rougher concentrate. The second approach utilises two novel reagents, AT-131 and AT-202, which have been developed recently. Excellent metallurgical performance has been obtained in a commercial test and a batch test, respectively. The MgO content of flotation concentrate can be reduced to about six per cent.

Jan 1, 1996

By Stanojevic R, McGlinn PJ, Day RA, Levins DM

This paper reports the results of a number of studies that Ansto has carried out for mineral sands companies concerned about low-levels of naturally-occurring radioactivity in their products. Where measured levels of radioactivity have exceeded allowable levels, Ansto has used specialised techniques to identify the source and distribution of the radioactivity and investigated processing strategies to remove the Contamination.

Jan 1, 1993

By Dredge K, Becker G

The successful dissolution of the valuable metal components of a solid phase is often a basic requirement for a successful hydrometallurgical treatment process. Sulphide concentrates are often an intermediate product in the production of refined metals. These concentrates need to be further processed to realise the contained metal values in a useful form. Pyrometallurgical techniques have tended to dominate, at least the initial treatment of metal sulphide concentrates. The technology described, Activox«, has been developed specifically for the hydrometallurgical treatment of these sulphide mineral concentrates, in particular those containing copper, nickel or gold. The Activox« dissolution technology coupled with the use of existing, or newly developed, downstream processing techniques, offers alternative processing options for the recovery of full value, saleable metal products. The technology is suitable for application down to relatively small scales opening up the opportunity for on-site production of metals even at modest scale mining Operations.

Jan 1, 1995