Search Documents

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

By Miller M. J, Bauer J. C

The continuous copper drossing process operated at Port Pine since 1962 has had limited copper removal capacity as determined by a maximum tolerable Cu/S ratio in feed and the level of sulphur in blast furnace bullion. Recent process development has been to overcome these limitations to meet increased copper throughput requirements. A sulphur addition system was developed and installed in August 1987. The system has capacity to increase sulphur input by over 150%, meeting the increased copper capacity requirement and also allowing independence from the upstream process for sulphur supply. Developments in process understanding have been applied within the limitations of the existing furnace design with a 10% increase in the maximum tolerable Cu/S ratio.

Jan 1, 1989

By A G. Thompson, E Villaescusa, D Howard

The Western Australian School of Mines (WASM) has developed a facility for the static testing of full-scale ground support elements (Morton et al, 2007). The test facility consists of several stiff steel frames used to support the sample and a screw feed jack is used to load the sample. A large-scale punch test method has been developed to load various shotcrete configurations. The shotcrete is sprayed on to a rock substrate containing a centrally located circular disc. The rock and shotcrete sample is placed on to the sample frame and restrained on all sides. The circular disc is displaced at a constant rate by the screw feed jack which in turn loads the sample. Instrumentation measures the displacement and the load being applied to the sample through the loading disc. The testing method is described in detail and the results from the testing program are presented. The results show that it is possible through laboratory testing to simulate some of the mechanisms of shotcrete support reactions better than conventional beam and panel tests.

Jan 1, 2008

By M Cooksey, C Goodes, G Wellwood

Light metals have great potential for application in the automotive and aerospace industries because of their excellent physical properties. The usage of aluminium, titanium and magnesium is limited by relatively high costs of production, associated energy costs and large ecological footprint. In the case of aluminium, significant improvement to the Hall-HTroult process is still achievable through advances in cell design, materials and process control. Alternative production processes, including carbothermic reduction and low temperature routes are also possible. Magnesium and titanium production are currently dominated by batch metallothermic processes and new process routes are required to develop these industries. Research at CSIRO, through the Light Metals Flagship, is currently focused on step change improvements in the production of light metals, aimed at lowering energy usage, increasing productivity and reducing the overall environmental impact. In this paper, the overall status of the existing technologies will be described, highlighting areas that are being developed around the world and at CSIRO.

Jan 1, 2006

By Whiten WJ

A method that allows data to be mass balanced and screen models to be fitted in a single step is described. The inclusion of several variables to describe the feed data in the fitting procedure allows a mass balance to be conducted at the same time as the fitting of the screen model. Analysis of Groote Eylandt Mining Company screening data has demonstrated that this method is ideally suited to applications where complete stream data are not available. Also, certain random fluctuations in screen model parameters arising from the fitting of consecutive mass balances and screening models are significantly reduced. A cubic spline function with fixed knot positions corresponding to particle sizes and variable (fitted) cumulative percent passing values is used to describe the feed size distribution. When the spline function is interpolated at the experimental feed particle sizes a fitted feed size distribution is obtained. This feed size distribution is then used as input to the screen model calculations from which product size distributions are generated. Since both feed and product size distribution data are used to minimise the residual errors between the observed and fitted stream size distributions, a mass balance is Conducted simultaneously with the screen model parameter fitting.

Jan 1, 1984

By Corbett GJ

Magmatic-related low sulphidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar - sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.

Jan 1, 1995

By De Broglio R

The Mae Moh coal deposit was discovered some 60 years ago by villagers who noticed spontaneous combustion of coal outcrops. The first production began in the 1950's to fuel a fertilizer plant and a 12.5MW power station. During the period 1976 to 1979, three 75MW power station units were constructed on site. These have a total daily coal consumption of some 5000 tonnes and are served by a stockyard of approximately 60 000 tonnes total capacity. Stacked coal is reclaimed by means of a front end loader onto reclaim conveyors. During the years 1983 to 1986 four 150MW power station units were constructed east of the eastern seam subcrop, sons 2 km from the original power station complex. These have a daily coal consumption of nearly 12000 tonnes and are served by a stockyard of total capacity 270000 tonnes, equipped with two stackers and two bucket-wheel reclaimers for a totally mechanised system.

Jan 1, 1986

By Cairncross A. A

Papers on technical aspects of the Melbourne Underground Rail Loop project are being presented at this conference or have been presented previously or will be presented at other forums. This paper provides the framework for these papers by presenting the overall engineering tasks. The conceptual design, the special investigations undertaken, the management of the project and the construction development are highlighted.

Jan 1, 1981

The series of events leading to the adoption of more complex flotation circuits for coal have been reviewed. In essence, it has been concluded that ac- ceptable overall flotation recovery will only be obtained when efficient distri- bution of collector over all the component feed size fractions is ensured. The achievement of this goal is most likely to be obtained by feed classification and separate flotation of appropriate size fractions. The adoption of such a phil- osophy, however, imposes a number of process problems of both a chemical and an engineering nature. Some of these problems have been identified and possible solutions discussed. A case is emerging for the development of a new generation of flotation cells designed specifically for the flotation of classified coal and for the development of a series of novel re- agents which have the propensity to float middling particles.

Jan 1, 1984

This problem is seen as being central to a number of peripheral problems. Of these, the following are considered to be of major importance: 1. Reserves. Changes in Quality. Depths at which they occur. The effects of catchment and water storage areas. The effects of urban development. 2. Environment and the compat- ibility of mining and preparation of coal. 3. Transportation of Coal. J. tabour.

Jan 1, 1976

Jarrah Decline is currently the only underground operation at the Boddington Gold Mine, (BGM). The mine is located 120 km SE from Perth in WA, with mineralisation hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt (Morley and McBride,1995). Open cut operations commenced in April 1987 with a mill throughout of 3.OMtpa. A number of upgrades have since taken place, with the oxide material throughput currently milled at a rate of 7Mtpa. In 1992 a separate circuit, the supergene mill, was commissioned to treat copper material from the open cut and now ore from the Jarrah Decline. Current throughput in the supergene plant is 30,000 tonne per month, with a varied blend according to mill requirements. Total gold production from the Jarrah Decline in 1994 was 60,000 ounces from 90,000 tonne of ore.

Jan 1, 1990

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

By H Zahiri

Utilisation of the InSAR technique for monitoring of subsidence in mining areas, employing open pit and underground mining methods, has large potential due to sensitivity and safety issues associated with usage of the classical surveying techniques. InSAR can also be very competitive concerning the cost of provided results. However, there are a few issues that may significantly limit InSAR applicability for subsidence monitoring in mining areas. The altered terrain topography, involving steep slopes and deep pits, may lead to the layover of radar signal for specific satellite and pit geometry. Also, the highly dynamic character of subsidence induced by mining, especially using mass mining methods, may lead to issues such as apparent heave and ambiguous results. In this paper the authors analyse the above-mentioned issues and demonstrate how InSAR technology was applied, as a supporting system, to monitor large scale and highly dynamic subsidence for a real case study in Western Australia.

Jan 1, 2008

By OÆBrien D, Priddle D

In order to avoid costly moisture penalties on coal shipments and to minimise rail freight costs, screen bowl centrifuges were selected and installed in the Mount Thorley Coal Preparation Plant for dewatering fine coal product. The Mount Thorley fine coal circuit consists of desliming the -0.5 mm (ww) fine coal in two stages of classifying cyclones prior to recovery by froth flotation. Provision has been made to bypass the flotation circuit with the classified flotation feed reporting directly to product and the centrifuge dewatering circuit has been designed to handle either flotation feed or flotation product. Major mechanical failures of the gearboxes and the ceramic tiling occurred early in the operation life of the machines which led to design changes being made to achieve satisfactory operation. This paper discusses the operating experience at Mount Thorley with respect to both mechanical and metallurgical performance of the screen bowl centrifuges since their installation in 1985.

Jan 1, 1989

By Sharma T

Laboratory investigations have been carried out on direct leaching of lead-zinc complex sulphide ore and zinc concentrate using ferric chloride. From the investigation it was observed that the use of 0.15 M and 2 M FeC13 gave an optimum dissolution of metal ions from ore and concentrate respectively. The kinetic studies conducted showed that the leaching reaction followed a shrinking core model for galena and sphalerite. The presence of impurities such as pyrite had increased the dissolution rate and reduced the consumption of ferric chloride. Further, the studies were conducted to recover dissolved zinc from the chloride solution by selectively precipitating it as zinc ammonium chloride.

Jan 1, 1992

Recent operating experience from West Australian open pit gold mines has shown that geotechnical input into initial design is rare. As a result, ground stability is poor - almost half the pits designed in this way suffer major failure.West Australian experience shows that geotechnical studies for individual mines are site specific, and therefore empirical experience cannot be transported from site to site. Geotechnical studies performed prior to design have resulted in significantly improved pit stability.

Jan 1, 1990

Cable bolts are being used more extensively by the mining industry for many different rock reinforcement applications. The configuration of these bolts has evolved over the last 20 years to meet the immediate needs of industry at the particular time. Most improvements to date have focussed on increasing the mechanical performance with little attention given to issues such as ease of handling, matching response to that of the rock mass or corrosion protection. Ultrastrand has been designed and being developed with this broad perspective in mind so that it will satisfy the ground reinforcement needs of today's and tomorrow's mining industry.Laboratory tests on Ultrastrand prototypes have confirmed that mechanical performance is superior or equivalent to Standard and Birdcage Strand respectively. Preliminary discussions have been held with an installation equipment manufacturer with a view to conducting a trial at a mine site by early-1992.

Jan 1, 1992

By Ramsay WRH

The Mount Stavely Volcanic Complex compri- ses one of a number of northerly trending fault bounded greenstone occurrences in Western Vict- oria, of probable Cambrian or older age. The greenstone belt is coincident with several linear positive aeromagnetic anomalies, which outline the surface and subsurface extensions of these greenstones. Mapping at Mount Stavely has identified serpentinite, variolitic basalt, two-pyroxene and pyroxene-hornblende andesite, dacite, rhyodacite and their pyroclastic equiv- alents. Chemically and mineralogically the volcanics constitute a calc-alkaline assemblage. The mineral potential of the region has been enhanced following a discovery by Pennzoil of Australia Limited near Ararat, of sulphide min- eralisation containing approximately 1 million tonnes at 2.7 percent copper. The volcanic environment of the Mount Stavely Volcanic Complex is discussed in terms of similar environments found in Canada.

Jan 1, 1982

The mining industry is facing tremendous economic challenges. Fluctuating and depressed commodity prices, the ever-increasing pressure from environmental legislation and the competing global opportunities for capital investment are placing enormous strains on every aspect of the mining business. At the same time, mines are generally becoming older and deeper with all the logistical and rock mechanics difficulties that this entails. In the face of these new challenges the industry looks to technological advances to make operations more efficient and profitable. One approach is to develop and implement highly automated and computerised equipment as part of a trend towards major reductions in the underground workforce. This approach requires more capital investment rather than less and requires a more sophisticated and well-educated workforce with skills which are generally in high demand in society as a whole. It is difficult to see how the benefit that can be gained from such technology can justify the expenditures necessary to make it operate reliably underground on a daily basis. Nor is it easy to foresee how the mining industry, based as it is often in very remote areas, will be able to hire and retain sufficient numbers of people to maintain such fleets of equipment. Another approach, and the one which I favour, is the implementation of much greater control over the whole of the mining process. Mining is essentially a very simple process - we break rock and move it. The most cost-effective means of moving and processing the mining product depends entirely on the way it is broken - it depends on primary fragmentation by blasting. I propose that the way forward for the industry in the face of our present difficulties, is not new technology but is to utilise the level of technology which currently exists in ways which have traditionally been regarded as too difficult or too inflexible - improved fragmentation and the use of conveyors. The technical success of this approach depends on the complete re-design of the ore handling system from the face or stope drawpoint to surface. The fundamental issue which determines the success of this approach is designed fragmentation.

Jan 1, 1995

The Hall-Heroult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-Heroult cell- the electrolyte, the anode and the cathodes are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride-carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.

Jan 1, 1987