Search Documents

By Lunt D

Arsenic is classified chemically as a metalloid. That is, it has properties intermediate between those of metals and non-metals. Like non-metals, it combines with many metals to form arsenides (eg arsenopyrite FeAsS, niccolite NiAs, sperrylite PtAs2), but like metals it forms sulphides and oxides (eg realgar AsS, arsenolite As203). Arsenic is distributed widely in the Earth's crust at an average concentration of 1.5 mg/kg and is present in more than 150 minerals.

Jan 1, 1991

By Chang JF

This paper describes the advance in shaft sinking technique in terms of a vast complex of equipment in the last decade, and mainly recommends some ad- vanced technology and a vast complex of equipment, such as smooth blasting, la- ser guiding, shot-crete lining and rock- bolting, hanging bracket ring for drills, large-capacity wall grab, tipping device, storage bunker, and automobile haulage et.al., finaly, author in detail repre- sents some successful applications of advanced shaft sinking technique in some mines as an example.

Jan 1, 1987

By Mann T

The use of dolomite as a refractory began in England about 1870 when the basic Bessemer process for the removal of phosphorus from steel was developed by Thomas and Gilchrist.Knowledge of dolomite as a refractory in this country goes back to the early part of this century, at the time when the Hoskins Brothers took over the Lithgow Iron and Steel Works from W. Sandford. The practice then was toimport burned dolomite in casks from England. It is reported that much of the material was powdered when received, but was still serviceable. The earliest. used sources of local stone were in the Bathurst and Mudgee areas of New South Wales, and these dolomites were first used raw. Later, dolomite was burned in cupolas at Havilah near Mudgee, coke being obtained from the South Coast of New South Wales. This plant supplied burned dolomite to the Lithgow steel plant, later to the Australil1n Iron and Steel plant at Port Kembla, and also to the electric steel furnaces at Newcastle, Sydney and Melbourne until the plant was closed down in 1946.The Broken Hill Proprietary Company first obtained its dolomite from George's Plains near Bathurst (this was, really a magnesium limestone) and later from Mount Knowles, a deposit near Mudgee, which was eventually taken over by the CO:plpany in 1918. In 1936 Australian.Iron and Steel acquired from the Southern Portland Cement Company a deposit at Mount Fairy in the Federal...

Jan 1, 1951

By Oliver R

The Hamersley Iron ore resources are geologically complex with fluctuations in mineral chemistry. From this resource Hamersley Iron must produce consistently high quality direct shipping products and have the ability to evaluate the effects of changes in demand. In order to achieve these objectives an incremental long term planning technique has been developed. This method reduces the total geological resource statement into a simple, logical sequence of events. A logical sequence of mining increments is defined within individual areas based on a final pit and access system. Increment characteristics are derived manually and from a computer based orebody model. The end product of the technique, an optimum mining schedule, is readily developed from the incremental information. Among its many benefits, this simple technique rapidly provides management with information for policy formulation.

Jan 1, 1979

Over the 20 years to 1990 the Australian mining industry, presently worth some $A60 billion, generated a negative real rate of return (McDonald, 1992); not surprisingly under-performing the returns from bonds and industrial equities. Over this same period more than $A70 billion was invested in expanding the Australian mineral industry.

Jan 1, 1993

The paper is aimed at mining engineers and other mining practitioners in the metalliferous mining industry who are considering the use of roadheaders and wish to understand the basic geomechanical and operational principles controlling their performance. The paper aims to address metalliferous minersÆ general unfamiliarity with roadheader technology, which is one of the factors which has limited the application of these machines in such mines. The historical development of drag tool mechanical excavation machines is briefly discussed, and factors affecting the application of roadheaders are mentioned. The mechanics of cutting with drag tools is then reviewed as are the effects of these and tool wear on tool performance. The implications of tool performance to roadheader performance are mentioned, the potential benefits of high pressure waterjet assistance are discussed and the relative performances of different tool types and materials are compared. Roadheader performance factors including productivity and utilisation are mentioned, and the state-of-the-art of conventional roadheaders is discussed in the context of machine weight, power and cutting head configuration. The influence of these and rock strength on machine productivity is analysed. Alternative, developing technologies are discussed which may extend the effective use of mechanical excavation into stronger rock masses which are beyond the range of conventional roadheaders. Finally, conclusions on these discussions are presented, along with recommendations for continuing research and development.

Jan 1, 1997

By Roach C

Exploration on the Callide Coalfield by Thiess Bros. Pty. Limited had reached the stage in mid 1976 where there was a need for a comprehensive appraisal of the coalfield geology. Exploration strategy in 1977 - 1978 was defined by the selection of the most attractive targets. All available literature, reports and plans were reviewed and borehole records assessed. The geology of the coalfield was placed in its regional setting and the genesis of the Callide Coal Measures described in a structural and sedimentological context. Their general form and extent was then examined by the technique of stratigraphic analysis through the interpolation and extrapolation of the available data. A "localized" reserve classification was drawn up and reasonable estimates of the various geological reserves produced, in terms of their reliability and depth of overburden. Quality trend maps were also produced. The resultant "base map" was virtually a summation of all the information to June, 1977, and the basis for the exploration programme in the 1977 - 1978 financial year. The technique allowed for "base maps" to be produced at almost any stage, each one a refinement of its Predecessor.

Jan 1, 1978

In recent years the use of directional drilling has become increasingly popular in several applications. These include shaft pilot holes, exploration drilling, mine service holes and drilling beneath surface structures and obstacles. The prime objectives are to increase accuracy and reduce time, cost and environmental disturbance.

Jan 1, 1992

A study is presented of the theoretically possible initiation systems for outbursts and the subsequent propagation mechanism.Previous occurrences of outbursts and their correlation to the theoretical system are described. An estimation of the energy release from two energy sources, gas strain energy and rock/coal strain energy, is presented and the relative importance of each source in the severity of outbursts. Summary: The description of mechanisms of outbursting follows the examination of these phenomena at Collinsville in Bowen No. 2 mine and at Leichhardt Colliery, Blackwater. Quantitative material contained in the paper refers to Leichhardt Colliery, Blackwater. Clearly from the work carried out to date gas release has a major part to play in the out- bursting at both of these collieries. In the case of the December 1 1978 outburst at Leichhardt Colliery energy release estimates place gas strain energy release contributing eight times the energy of that from rock/coal strain energy. Even the normal outbursts at Leichhardt Colliery appear to show this trend. Estimates of energy released are for comparative purposes between gas and rock strain energy and the values obtained may be regarded as approximate.

Jan 1, 1980

By Will D

This presentation is to outline the current practice of mechanised stoping a one-metre wide, gold bearing ore body to optimise fragmentation, minimise dilution and reduce stoping costs.Coolgardie underground operations have historically been mined using traditional shrink stope methods, but in this recent economic environment (with falling gold prices and high costs of traditional methods) it was necessary to look for alternative methods in order to reduce costs and increase productivity.Although still in a learning and refinement phase, CGNL is satisfied that it is feasible, practical and more economic to use mechanised long up-hole stope and long-hole rising methods to significantly reduce the mining cost, reduce dilution, increase safety and increase productivity three-fold compared to traditional airleg methods used throughout the Fasten Goldfields.

Jan 1, 1993

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

The scope of this paper has been restricted to the manufacture in Australia of seamless steel tubing, as the subject of buttweld tubing has already been dealt with by A. N. Hamilton in a paper delivered before the Institute in 1935.The earliest attempts to produce seamless steel tubes were based on the extrusion of lead piping, a process developed by Thomas Burr in 1820. However, the problems associated with the extrusion of white hot steel had to await the metallurgical knowledge of the twentieth century, and these early attempts were unsuccessful.The years 1840 and 1845 were noteworthy for the introduction of the first practical methods of making seamless steel tubes. In one process, a large circular plate was 'cupped' in a vertical press; in the other, a round steel billet was pierced for its entire length.The product from both these methods was then elongated by repeated reheating and rolling over an internal mandrel, in a circular pass mill.At this juncture, it should be noted that every process developed for the manufacture of seamless steel tubing can be divided into two parts. In the first part of the process, attention is centred on the conversion of the heated bloom into a short, thick-walled, hollow cylindrical forging; this product is then elongated in the second section of the process. It will be noted that these two sections are actually quite distinct, and in practice numerous methods exist for carrying out both functions. The first stage is generally referred to as 'piercing', the second stage being termed 'elongating.' In this paper, the author proposes to outline the various methods adopted for piercing and elongating; the reader is asked to note that although certain methods of piercing are almost invariably associated with only one method of elongating, the distinction between the two functions is, nevertheless, a vital one and should be noted accordingly.

Jan 1, 1947

By Yoshii Y

Many kinds of shield machines are being driven in the soft ground of Tokyo metropolitan area. Tunnel alignments for underground power transmission lines are generally planned to pass under public roads where facilities, especially life-line facilities, are densely located. Therefore, it is frequently required to drive the shield machines along very sharply curving routes. This paper reports on the performance of the new shield machine - the Sharp Curve Excavation Shield Machine - developed by Tokyo Electric Power Co., Inc., which can freely drive along a much sharper curve than conventional machines. Some of features of the developed devices of this machine are, maximum flexing angle of 6.5 degree in all deirection at the middle of shield body, maximum bending angle of 3.5 degree in all direction at the cutter disc, and so on. This shield machine can there- fore drive along curve of minimum radius 15m. The machine was confidently applied to the const- ruction of tunnel in soft clay strata at N values 2 to 5. Outer diameter 3.7m. Length 202m. Horizontal curve; radius 15m, length 20m x 2. Vertical curve; radius 30 m, inclined driven up 29%. The behaviors of the shield machine, segments and surrounding ground were monitored during construction for safety and efficiency check of this machine.

Jan 1, 1987

By Hunefeld R

In the field of mining engineering, design and planning are complex tasks, which require the knowledge of various engineering disciplines. GRUBE (Graphisch-RechnerUnterstiitzter BergwerksEntwurf) is a modular databased program system, which offers computer aid for all mining departments using a 3D CAD software as the user interface. Despite the data quantity and complexity, specific and uniform working conditions have to be applied to the planning of technical equipment of a pit. With the application of 3D graphics, complex data stores and their interrelations become 'palpable' for the user by suitable visualisation. GRUBE-M forms the mechanical operations module of GRUBE, in which underground locations displayed as three-dimensional graphic models are `equipped' interactively. Planning alternatives can be created and compared quickly in terms of technical calculations and economical analysis.

Jan 1, 1995

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

By den Drijver J

Worldwide, hard coal mining is being carried out at ever increasing depth, and has, therefore, to cope with correspondingly increasing methane emissions. About seven per cent of global methane emissions are caused by coal mining. Beside carbon dioxide, chloro-fluorocarbons (CFCs) and nitrogen oxides, methane is one of the most significant `greenhouse' gases. It is mainly through the release of such trace gases that the greenhouse effect is brought about. Reducing methane emissions is therefore an important problem to be solved by the coal mining industry. This paper begins by highlighting some of the fundamental principles of methane in hard coal mining. The methane problem in German hard coal mining and the industry's efforts to reduce methane emissions are presented. The future development in German hard coal mining is illustrated by an example which shows how large methane volumes can be managed, while still maintaining high outputs at increasing depth.

Jan 1, 1995

By Coulborn W. T, Glasby G. P, Maylan M. A

Research cruises by HMNZS 'Tui' (1986) and RV 'Moana Wave' (1987) investigated the geology, geophysics and seafloor mineral resources of Manihiki Plateau in the central Pacific Ocean.Manihiki Plateau is a large (500,000 km2) mid-ocean platform that rises 3000 m above the abyssal plains of surrounding ocean basins (depth -5500 m). Its foundation evolved about 112 Ma ago by massive outpouring of basaltic lavas at a plate triple junction. The plateau is blanketed by a 900 m thick sedimentary section comprising (i) mid-Late Cretaceous volcaniclastic sandstones / siltstones grading upwards to limestones / chalks and (ii) -500 m of Tertiary nanno-foram chalks and oozes. Cores from DSDP 317 drill-site on the Manihiki High Plateau indicate that the volcaniclastic sediments contain native copper and some thin beds rich in organic carbon.

Jan 1, 1990

About 20 percent of world gold production has been contributed by gold deposits in Archaean greenstone belts, of which ca 2100 tonnes of gold has been produced from Archaean greenstone belts in Western Australia (Phillips, in press). These deposits are, therefore, important exploration targets and an under-standing of their nature and genesis can help to formulate exploration strategies and delineate potential targets.A literature survey of Archaean granitoid-greenstone terrains indicates that a wide variety of lithologies host gold deposits. The major part of production from the Yilgarn Block, Western Australia, has come from mafic volcanics andintrusives (70% of production),with significant contributions from BIF-hosted ores (15%) and low production from sediments, felsic volcanics, porphyry intrusives and granitoids (Groves et al., in press). Similarly, most

Jan 1, 1984

Amongst the Pacific Rim countries, Papua New Guinea (PNG) is the leader in new gold discoveries and developments leading to new production. PNG has shown a dramatic increase in gold production when taken from a base of about 600 000 ounces in 1984 to 1 160 000 ounces in 1986. 1987 is expected to produce about 1 500 000 ounces and new planned developments will give further large increases. PNG's leading position when compared with neighboring Pacific Rim countries is only partly due to its favorable geological setting along the "Rim of Fire" epithermal zone. More important have been well-thought-out mining development legislation and good administration as well as consistent taxation and royalty policies. A stable political environment and a track record of new mining developments over the last 15 years, both pre and post Independence in 1975, have also been important factors in encouraging the new developments. Early Portuguese explorers associated the New Guinea mainland with gold as early as 1525 but it was not un,11 1R77 that a small ill-fated gold rush gave the first recorded production at Laloki near Port Moresby. Modest but commercial discoveries were made in the outer islands and coastal mainland regions from 1888 to 1926. In 1922 William "Sharkeye" Park found gold at Edie Creek and this led to major discoveries at Wau and Bulolo which were the first large scale commercial gold Operations.

Jan 1, 1987

The originally estimated mine life at Kidston (starting 1984) was 12 years. Through a continuing process of re-evaluation and improvement in the operation and by expanding the geological knowledge in the region, the mine life has been considerably extended. With falling grades and harder ore, the additional reserves have come with increasing risk - not only in an economic sense associated with diminishing profit margins but also operationally, requiring innovative milling technology and geotechnical designs to provide a lower cost environment for continued profitable mine production.

Jan 1, 1994