Search Documents

By Erepan P. C

Flash flotation technology was introduced by Outokumpu in 1985. Considerable success was achieved in other plants with similar operations to OTML. Conclusions from site visits and amenability tests performed on plant samples were that the OTML

Jan 1, 1997

By J M. F Clout

The low-grade clay-rich -1.0 mm fraction of fine iron ores have often proved difficult to upgrade and capital intensive to process when using traditional wet beneficiation technology including single or two stage hydrocyclone desliming, wet high intensity magnetic separation (WHIMS), spirals and final dewatering using fine screens. Very fine (<0.010 mm) clay-rich slimes simply follow the water split to the hydrocyclone underflow where it often impedes the subsequent processing performance of any downstream spirals and can result in troublesome direct dewatering of hydrocyclone underflow. The -1.0 mm fraction in goethitic iron ores is typically considered as waste. A new two-stage wet gravity separation flow sheet, referred to as the ædesandÆ process, has been designed to overcome these issues for the upgrading of low-grade clay-rich goethitic or hematite-quartz fine iron ores. The desand process is designed to treat the -1.0 mm range from -8.0 mm natural fines, to recover a -1.0 +0.038 mm higher-grade fraction by rejecting to tailings any low-grade clay-rich ultrafines and low density sand-size fine chert/quartz gangue and shale.The desand process consists of wet screens with a nominal 0.7-1.0 mm cut point which direct the undersize to hydrocyclones. The hydrocyclone underflow is then fed to upcurrent classifiers where the classifier middlings is sent to spirals and classifier and spirals concentrates are then dewatered using vacuum belt filters or fine screens. The three product upcurrent classifier is employed to further deslime the hydrocyclone underflow, producing firstly a coarse final concentrate, and then a deslimed middlings for feeding to spirals as well as a 0.100 mm clay and fine quartz or banded iron formation (BIF) sand in final overflow for feeding to the residue thickener. The upcurrent classifier middlings provides the spirals with a significantly cleaner feed material than traditional methods, with the end result that the spirals do not silt up with slimes and therefore can continue to run at their optimum. The upcurrent classifier and spirals form a complimentary pair, with the upcurrent classifier better able to send coarser, acceptable grade particles to concentrate and fine slimes to tailings whilst allowing the spiral to better reject coarser, subgrade low specific gravity particles. Test results for the Mayoko-Moussondji iron project, Republic of Congo, using upcurrent classifier-Wilfley Table (simulating spirals) gave acceptable mass recovery from run-of-mine (ROM) and Fe recovery from hydrocyclone underflow for HEMCOL (6.2 per cent mass recovery from ROM/43.1 per cent Fe recovery) and HEMBIF2 (5.1 per cent mass recovery from ROM/22.3 per cent Fe recovery) mineralisation types. The desand process also enables improved dewatering of -1.0 +0.038 mm product from a clay-rich plant feed.A number of new wet plants in the Pilbara use the desand flow sheet including FMGÆs Cloudbreak and their two Christmas Creek plants. Many potential new applications are being explored, with new iron ore plants in India as well as those being proposed for West Africa. Operational experience has highlighted the importance of providing clean process water to the upcurrent classifiers as well as ongoing design improvements including increased wear life, reduced maintenance and enabling a more steady feed rate to spirals.CITATION:Clout, J M F, 2013. Beneficiation of fine iron ores using the desand process, in Proceedings Iron Ore 2013 , pp 337-348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Raudsepp R

Since 1991, the Porgera Joint Venture has processed refractory sulphide flotation concentrate by pressure oxidation with the subsequent gold recovery, from the washed residue, via a conventional leach/carbon-in- pulp (CIP) circuit. The capacity

Jan 1, 1997

Goodenough and Fergusson Islands, in eastern PapuaNew Guinea, lie in an area of crustal extension on the western end of the Woodlark Basin seafloor spreading system. The islands are made up of a number of mountainous domes of complexely deformed basement, and these are intruded by large bodies of granodiorite. The domes are bounded by curved shear zones and faults dipping outwards at angles of around 25 to 45¦. The cores of the domes contain lower crustal rocks of eclogite and granulite facies, these rocks have undergone retrograde metamorphism in the outer sheared zones. Movement indicators on the shear zones indicate a complex moverm.-It geometry which does not fit the models proposed by earlier workers. These dome-like structures are similar to the metamorphic core complexes of the western United States Cordilleran region, however there are a number of aspects which do not fit with the models proposed for the development of metamorphic core complexes. Uplift of the metamorphic basement probably resulted from a combination of forces associated with the extension of the crust and the intrusion and emplacement of granodiorite plutons.

Jan 1, 1990

By S T. Jarvis

Colliery spoil is the major constituent of colliery spoil ærockpasteÆ which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpaste are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising infilling a 6600 m3 section of an abandoned mine was conducted prior to the infilling of the Littleton Street Mine which had a volume of about 500 000 m3. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully used for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over 11 mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By Thomas MJ

The Cannington silver-lead-zinc deposit is located at latitude 21¦ 52' 9" South, longitude 140¦ 55' 10"" East, on the south-eastern margin of the Proterozoic Mount Isa Block (Figure 1), 135 kilometres south-east of Cloncurry. Access is via a graded shire road for 80 kilometres south from the small pastoral community of McKinlay.REGIONALThe deposit is hosted by the Proterozoic Soldiers Cap Group within the Mount Isa Block Eastern Succession. South of the Cloncurry Beardsmore et al (1988) have grouped part of the Eastern Succession stratigraphy intothe Fullarton River and Soldiers Cap groups (1760-1740 million years) which together make up the Maronan Super Group. This is an apparently conformable sequence 10 kilometres thick and consists of metamorphosed sediments and volcanics with intrusive amphibolite bodies.The Maronan Super Group has experienced a complex history of deformation with up to six events having been recognized. The stratigraphy trends broadly north-south and is predominantly characterized by tight, upright isoclinal fold structures.

Jan 1, 1993

The mining of remnant coal reserves at the Liddell Open Cut is subject to a number of risks. These risks are of both a technical and financial nature. Liddell Open Cut is principally a conventional truck and shovel/loader operation, supplemented by a highwall coal augering operation. There are significant areas of divergence from more conventional operations including working in close proximity to a major dam, working up dip from an operating underground mine, and working through areas where there has previously been underground extraction. In addition the site has major long-term rehabilitation requirements. This paper, rather than concentrating on specific detail of areas of risk, presents the spectrum of geological, design, operational and post-mining risks that accrue to the various areas of activity in this open cut operation. The balance of this paper then provides an outline of the strategies employed by Liddell Coal to manage their potential impact.

Jan 1, 1994

By J Hadjigeorgiou

Underground mines often rely on ore pass systems to ensure the transport of ore and waste. Consequently, it is important to ensure the smooth operation of such systems. Ore pass degradation that may require rehabilitation results in production delays and high operational costs. The occurrence of hang-ups within an ore pass also leads to disruption of ore production. There are important safety concerns when worker intervention is necessary to re-establish material flow in the ore pass. In order to facilitate the design of ore pass systems, mining operations often rely on past experience, or semi empirical guidelines. This paper describes recent efforts to establish a comprehensive database on current practices; encountered operational problems and solutions in ore pass design in Quebec underground mines.

Jan 1, 2003

By T Laurencont

The Queensland Department of Natural Resources and Mines (NR&M) accepted the environmental liability for the Mount Morgan minesite in 1991. This gold and copper mine located 38 km southwest of Rockhampton had been in operation for more than 100 years. Mining leases are still active while the feasibility of a reprocessing operation is carried out. From 1993, NR&M have operated a seepage interception pumpback system which has reduced the chronic load of acid rock drainage (ARD) to the adjacent Dee River, a tributary of the Fitzroy River system. In early-2000, it was recognised that a ten-year plan for rehabilitation of the mine, along with significant funding would be required if a long-term sustainable rehabilitation strategy was to be implemented at this minesite, ultimately making the seepage interception system redundant. A rehabilitation planning workshop coordinated by NR&M was held in May 2000. This workshop brought to the mine a range of technical expertise and key stakeholder groups. This workshop provided a technical forum for review of studies undertaken and to identify priority projects, which needed to be undertaken in the future to more clearly define contaminant sources on the mine site and to prioritise the rehabilitation program. Stakeholder consultation enabled the project team to be clear on community and other government (eg Environmental Protection Agency) expectations. It is clear that the future of the economically depressed community of Mount Morgan will be reliant on the careful management of the significant heritage values at the minesite for tourism, education and research. In the first year (2000), priority studies were initiated, which included whole of site studies on water balance, contaminant sources and a review of occupational health and safety and environment of the minesite and conservation and heritage scoping. Baseline vegetation and soil materials surveys were also initiated. The outcomes of these studies helped to shape the work program for the following year, while providing a basis for an additional funding application, which was granted. The second year of studies focused on building upon the existing baseline studies completed. In addition, studies focussed on addressing the priority issue of contingency planning for overflow from the open cut pit in accordance with best practice management of release water and river monitoring strategies were completed. Completion of these projects over the next six months will enable the optimal rehabilitation strategy to be defined in 2003. This optimal strategy may require the use of a water treatment plant for part of the ten-year program to provide space in the open cut pit for the deposition of ARD contaminant sources (eg waste dumps, tailings). It is envisaged that some sources will be rehabilitated insitu while others will be relocated to the open cut pit. Implementation of this strategy will be dependent on subsequent funding.

Jan 1, 2003

By Dickin FJ

Advances in the development and application of in situ imaging of mineral processing operations using electrical tomography techniques are reviewed and illustrated with case studies relating to pneumatic conveying, mixing and centrifugal separation processes. The potential for applying these methods to full three-dimensional visualisation of the dynamic behaviour of flow in pipelines and separators, and the resulting consequences for process-modelling strategies, are discussed.

Jan 1, 1993

Slope stability is a critical safety and production issue for open cut mines. The æslope stability radarÆ has been developed to remotely scan a rock slope to continuously measure the movement of the face. The system can detect and alert movements of a rough wall with sub-millimetre precision, and with reliability and resolution. The advantage of the slope stability radar over other monitoring techniques is that it provides full area coverage without the need for mounted reflectors or equipment on the wall. In addition, the radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. The measurement technique is tolerant of vibrations and overcomes the need for a highly stable footing required by traditional surveying systems, making it easy to move from one location to another. The system is self-powered and designed for minimal maintenance. Radar displacement images, co-registered with digital photography images, are transferred from the radar site in the pit to the mine office via a radio telemetry link. Custom-written software provides mine managers and geotechnical engineers with a complete picture of slope movements over defined time intervals. The time-history of the movement of any selected points or regions on the slope can also be displayed. Also provided is the ability to set movement thresholds that will trigger alarms at the radar site or mine office. The system has been used at numerous coal and metalliferous mines in Australia, and has provided real-time monitoring of slope stability during active mining operations. More than 20 rock wall and spoil failures have been captured by the system, and on every occasion adequate warning was provided to mine operators. The high level of movement precision and broad area coverage of the rock face provides a better understanding of the geodynamics, which leads to extra warning time. This technology enables a radical change in the management of risks in open cut mining operations.

Jan 1, 2003

This paper details successful implementation of a revolutionary pit access system involving excavation of an 'in-the-wall' ramp at Three Mile Hill open pit operated by Gold Mines of Coolgardie, formerly Goldfan Limited, at Coolgardie, Western Australia. Three Mile Hill is a medium-size, open pit, gold operation typified by hard, competent, fresh rock conditions from near surface. The project involved construction of a haulage tunnel or decline access located in the wall of an open pit in place of a conventional pit access ramp. Works undertaken as discussed herein included excavation, support, ventilation, dewatering, services installation, commissioning and monitoring. Prior to implementation, the conventional hardrock pit slopes and designs were constrained by the presence of infrastructure and a main road to the North and by adjoining leases to the Southeast. The combination of these factors and economic considerations resulted in a decision to proceed with an innovative in-the-wall ramp access system that is believed to be the first of its type in Australia. Back-analysis indicates that implementation resulted in a cost saving of as much as A$3.6 million and increased mineable pit reserves. The paper deals with the successful implementation and operation of the in-the-wall ramp haulage as well as an economic evaluation that is aimed at drawing some general conclusions on favourable conditions for implementation in other mining scenarios.

Jan 1, 1996

In recent years new instrumentation and digital technology have Wrote possible a new facet of goo-physics: broadband seismology. From digitally record-ing networks and arrays. broadband scistnograrns of body waves that are flat to displacement and veloc-ity in at least the frequency range from 0.01 to 5.0 liz can now be routinely obtained for most carthquakes of magnitude greater than about 5.5. In contrast to data from conventional narrowband seismographs, broad-band body waves have sufficient spectral information to nvest,igate the many frequency-dependent eflects that may arise from source finiteness and from wave prop-agat ion phenomenon. Besides the usual parameters of depth. moment and focal mechanism, broadband data have sufficient spectral information to provide estimates of radiated energy, associated stresses and the frequency dependence of source parameters. Moreover. teleseis-mically recorded broadband data and near-field strong motion accelerograms overlap in the frequency band be-tween about 0.1-2.0 Hz. Thus. v it h broadband data it is possible to connect far field and near field data in order to make estimates of acceleration for almost any seismically active region of the circum-Pacific.

Jan 1, 1990

By Scott IR

In stratigraphic orebodies, estimation of footwall and hangingwall location is often of more importance than grade estimation. Contoured grade estimates often produce smeared boundaries and the use of accumulations and thicknesses as variables re-introduces the original problem: location of the point at which the estimate is to be made. The paper introduces statistical and geostatistical techniques for the solution of the problem and illustrates the techniques with a case study from Mount Isa, one of the world's largest producing silver-lead-zinc deposits. Solutions for calculating variograms in orebodies of variable dip, strike and plunge are presented together with relative variograms for individual metals, metal accumulation and orebody thickness. Optimal methods for hangingwall and footwall location are introduced and illustrated with an example. Orebody boundaries are then kriged after which individual metal grades are kriged within the estimated boundaries. The boundary estimates are compared with manually interpreted boundaries and known boundaries in mined-out areas. Grade and tonnage estimates are compared in mined-out areas.

Jan 1, 1986

By Tuckey SH, Wake BA, Ariti J

Astute exploration on the northern Minahasa Peninsula, North Sulawesi, resulted in the discovery of the Toka Tindung, Pajajaran, Blambagan and Araren low-sulphidation quartz-adularia vein and stockwork gold-silver deposits. Combined, these deposits have estimated mineral resources in excess of I Moz gold at an average grade of 2.8 gAu/t and 7 gAg/t and are known as the Toka Tindung Gold Project. Gold typically occurs as fine grained electrum and is often associated with acanthite. The structurally controlled mineralised veins are hosted by Late Pliocene plagioclase and pyroxene-phyric basaltic andesite volcaniclastics and flows which form part of the Early Miocene to Pleistocene Sulawesi-East Mindanao Arc. Silica-adularia alteration dominates the volcaniclastic host of the Toka Tindung deposit. K-Ar dating of vein adularia indicates a 2.16 ¦ 0.04 Ma mineralisation age. Relatively narrow envelopes of silicification and argillisation surround the chalcedonic silica, quartz and adularia veins, stockworks and breccias at the other three deposits. Remnant hydrothermal breccias, chalcedony and anomalous arsenic, antimony and mercury indicate these gold deposits were part of a mineralised geothermal system.As of June 1997, Aurora Gold Ltd is finalising a feasibility study on exploitation of the four deposits and treatment of ore through a centrally located conventional CIP plant. Subsea tailings disposal is anticipated. Favourable metallurgy of the ore and logistics of the project area assist in minimising capital requirements.

Jan 1, 1997

By Brinkmann J. R

In the narrow stopes of South African gold mines, rockbreaking is carried out by drilling and blasting with safety fuse and igniter cord being used as the initiation system. The fuse/gniter cord system is used primarily because of its low cost, however several limitations of this method include: inaccurate delay time, unreliable firing, inflexible application to varied configurations, and the absence of dynamic interaction between holes. Alternative initiation systems that incorporate millisecond timing are being developed to overcome the limitations of fuse(tgniter cord systems. Current investigations by the Stoping Technology Division of the Chamber of Mines Research Organization (COMRO) into the effects of millisecond initiation are being conducted at a deep test site. Experimental blasts using various millisecond delays and the independent firing of holes with fuse/igniter cord are being studied in order to quantify the influence of delay time on the blasting process and to identify the best methods of applying millisecond initiation systems. The effect of design variables such as delay time, hole firing pattern, stemming, and panel layout are discussed. Blast results including throw distance and direction, muckpile profile and rock cleaning times are used in the discussion of different combinations of blasting variables.

Jan 1, 1990

By Giedl JG

Technical applications of computers within the coal industry are expanding rapidly with an increase in the number of users and user locations. Collinsville Coal Company Pty Ltd is an example of a remote and growing user company which has a Telecom link to MIM's ICL mainframe computer in Brisbane. The Planning Department is one of the technical user departments at Collinsville, with a variety of VDU, plotting and screen graphics hardware supported by the MIM Computing network. Current applications involve the storage, retrieval and manipulation of borehole information, plan and map production, volume calculations from survey data and mine ventilation modelling for underground Operations.

Jan 1, 1983

The investigations described in this paper aim at the development of a new impact mill. The objective is to produce particle size distributions below 10 .tm without using an air classifier. Circumferential rotor speeds of up to 200 m/s are strived for.

Jan 1, 1993

In any open pit mine some slope instability may be expected. This can range from small scale sliding on individual benches to large scale overall slope failure. This paper presents two case histories which illustrate how mining has successfully continued despite major pit instability. The common threads in each of these are listed below. 1. The recognition of the type and nature of movement (either regressive or progressive). 2. The successful application of simple monitoring techniques to minimise the potential impact on the mining operation, and 3. The management of the waste and ore excavation to avoid potentially damaging and costly situations.

Jan 1, 1986

Comparison of the Zadra, Anglo-American and organic solvent procedures for desorption of gold from activated carbon loaded in carbon-in-pulp gold circuits indicates that the Anglo American and the organic solvent procedures are considerably more effective than the commonly used Zadra procedure. Organic solvent elution procedures, particularly those using acetonitrile and acetone, can provide effective gold elution and very high concentrations of gold in eluate solutions. The operational simplicity and effectiveness of the Anglo American procedure would appear to make it the most satisfactory procedure available at the present time but this may change as the solvent elution procedures become better developed. INTRODUCTION The carbon-in-pulp technique has been introduced into the gold processing industry to by-pass the often lengthy CCD and filtration steps required in the conventional Merrill Crowe cyanidation procedure for gold recovery. Adsorption of gold on to carbon is also a valuable technique for recovering trace amounts of gold from low level waste streams from conventional processing procedures.

Jan 1, 1982