Search Documents

By Piga P, Sammarco O

Ventilation and the environmental climate in the Campiano mine is the subject of this re- search. The mine is located in Southern Tuscany (Central Italy), a region where geothermal gra- dients are very high (three times the average gradient of the earth). The research produced interesting indications as to the influence of surface climatic conditions on the environmental parameters inside the mine. A close correlation has been found between dry-bulb temperature and humidity ratio of the air in the mine for dif- ferent metereological conditions and for differ- ent mass flow rate values. Variations in air enthalpy, caused only by the heat exchange with the rock walls during the flowing of the air through the mine, depends on the surface temperature values. Statistical analyses have been used to ex- press air enthalpy variations on surface tempe- ratures, on the variations of the humidity ratio that the air undergoes inside the mine and on the mass flora rate. The application in practice of the results will permit the identification of correct mea- sures to be adopted so that optimal microcli- matic conditions are produced in the mine.

Jan 1, 1986

Rockbursts, as they occur in South African deep level gold mines, have a lot in common with natural earthquakes. Both violently release seismic energy and cause damage to underground and surface structures. Rockbursts are the main cause of fatalities in deep gold mines and the problem may increase in severity with future mining at greater depths. Although the emphasis in Rock mechanics is on the prevention of rockbursts, prediction would provide a partial solution to the rockburst problem. A research project was initiated in 1981 on Western Deep Levels to investigate the possibility of detecting and identifying precursive microseismic activity. This project has succeeded in locating potential sources of seismic events with reasonable confidence. The timing of these events may be estimated with less confidence, and an important parameter, namely the potential size of the rockburst, still cannot be determined. An example of a large seismic event and its associated precursive activity are discussed. Practical prediction systems will, at least for some time, involve subjective decision making which will place a new responsibility on the mine manager as well as the rockburst specialist. The moral pressure on the manager as the final decision maker will probably be greater than the fear of leqal prosecution.

Jan 1, 1986

By Liu Y

Ventilation, air leakage, and various cutting, loading and support movement operations all have a role in dust distribution on longwall faces as shown by the results of a large number of dust measurements on different longwall operations in the Bulli seam on the South Coast. It is concluded that leakage of air on the face has demonstrable mfluence on the exposure of the shearer operator to dust level. It is possible to calculate dust generated by various elements of a rrurung operation on the face from a single point measurement. In the examination of dust deposition from the source of generation as a function of particle size, it is found that respirable dust can remain airborne over long distances without any significant drop in concentration, if unobstructed.

Jan 1, 1995

By Swain H. D, Kay R. L

Assessment of mineral reserves in any ore- body hinges on both mineralisation characteris- tics and the economics of extraction. The mineral reserves statement depends on interpre- tation of diamond drill information by geolo- gists, determination of the production plan and operating costs by mining and metallurgical engineers and prediction of future income by economists. The techniques used to generate the mineral reserves statement for Bougainville Copper Limited in 1969 are described and the accuracy of predictions discussed. Preliminary results from a geostatistical reassessment are comp- ared with the ore zone model, blast hole data and concentrator reconciled production results.

Jan 1, 1979

By Grantham DL

ABS'TRACT For a number of years research efforts have been directed towards improving the efficiency of sampling and analysing coal mine roadway dusts. In the past decade the practicality of rapid, on site analysis of the incombustible content of these dusts using a radioactive technique has been receiving close attention both in Australia and overseas. Accurate measurement of the total incombustibles present is only possible by time consuming chemical methods. As the densities of the solid incombustible materials are greater than that of coal, they absorb a higher proportion of incident low energy gamma radiation than does coal. The amount of such radiation "back scattered" from mine dust samples is therefore inversely related to their average densities, and hence to their incombustible contents. This phenomenon can be used as a measure of incombustible content by employing an appropriately designed and calibrated instrument.

Jan 1, 1981

By Fabjanczyk M. W

The design of underground mine roadways (tunnels) requires a detailed understanding of the in situ stressfield, the rock failure modes, the performance characteristics of reinforcement or support members and assessment of the stress state about the roadway. Definition of these factors, together with monitoring of roadway behaviour during both development and extraction operations, allows rational design procedures to be undertaken.The design approach utilised computational techniques to simulate the behaviour of the strata about the opening for a range of anticipated stressfields and various reinforcement options. Field validation studies are conducted to confirm the design expectations.

Jan 1, 1993

Standard petrographic profiles for many Permian seams from New South Wales and Queensland have been drawn up. The standard profiles of seams of the same age and from one or more coalfields were used to compile an idealized or type seam sequence for those coals in which more than half the seam profiles were similar to one another. A marked similarity existed between at least 7 of the 10 type seam sequences formed. The configurations of the vitrite-plus-clarite contents of the plies of 95 per cent of the seams could be formed from different arrangements of 3 basic sequences: (i) a two-ply sequence with a lower vitrite-rich and an upper vitrite-poor ply; (ii) a two-ply sequence with a lower vitrite-poor and an upper vitrite-rich ply; and (iii) a four-ply sequence of 3 plies with vitrite-plus- clarite decreasing upwards, terminating in a vitrite- rich ply. The third basic sequence was very similar to a succession described for some British Carboniferous coals. Eighty per cent of the Australian Permian coal seams studied began with the first (i) basic type of sequence and are interpreted as originating in peat- forming areas which became progressively drier. More than half the seams were formed in an area with a stable depositional surface level which was subject to oscillations of small amplitude.. Many (30%) were formed in an area with a steadily rising depositional surface level.

Jan 1, 1969

By M Wortley, A Cantarutti, T Ozkocak

The estimation of the grinding mill charge weight is vital to ensure its efficient performance. Mill underloading or overloading can cause losses through decreased production or unplanned down time. Metso Minerals Process Technology Asia Pacific and South America (MMPT) has developed two systems for measuring mill load. The first is an acoustic system (SmartEarÖ) and the second is an online model-based charge estimation system. The aim of both systems is to facilitate better operation of grinding mills. SmartEarÖ performs analysis on an audio signal from the mill and allows each different frequency component to be viewed, analysed and used in process control for load estimation. By isolating different frequencies, SmartEarÖ can give an estimate of mill load. The online dynamic mill model uses measurable mill parameters (such as power) to predict the current total load. Kalman filtering can also be utilised to further increase the accuracy of the model. Both of MetsoÆs systems have been installed at BHP BillitonÆs Cannington mine to measure the load within their autogenous (AG) mill. In this paper, the methods of mill load estimation are reviewed and compared to the bearing pressure reading, which is the current method used by Cannington to control mill load. The redundant estimates of mill load provide increased confidence and consequently more robust grinding operation under a wide range of conditions.

Jan 1, 2008

By K S. E, S C. Parker, T K. Kundu

Understanding the fundamental principles governing the reactions at surfaces has always been the goal of theoretical surface science. The atomistic simulation techniques have been used to calculate the surface structures and the stability of quartz and wollastonite, and their adsorption behaviour in the presence of molecular and dissociative water, and the two widely used collector head group molecules of methanoic acid and methylamine. The dissolution behaviour of wollastonite has also been modelled. The calculated surface energy, hydration energy and reaction energy values have been examined and discussed in the light of flotation literature. These studies have given an insight into the interactions at atomic level, which indicate that modelling techniques should be capable of predicting the adsorption behaviour and to design the selective collector molecules, which is of central importance to the mineral processing technique of flotation.

Jan 1, 2005

By Hatherly P, Holt GE, McNally G

The current methodology for delineating and subsequently evaluating coal reserves is based on the use of vertical drill holes and surface based geophysics/geology. These techniques have three major problems, these being respectively:-a) Vertical drill holes can only provide a small sample of the coal seam and stratigraphy. Therefore the planar variation in coal reserve and environment parameters can only be approximated.b) Although surface based geophysics has had its fair share of success in recent years, there are still environments which have masked the finding of major structures.c) Access to drill sites is difficult at some locations due to mountaineous terrain, standing water and environmental impact.

Jan 1, 1985

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30km along strike, although economic resources are confined to a 7 km section in the vicinity of the Macraes township. The shear zone, which typically dips at a low angle (~20 o ) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, ælode schistsÆ and quartz-vein stockworks. Rehabilitation at the mine has focused on creating an environmentally benign site dominated by pasture to allow continuation of the traditional pre-mine farming economy. Changing regional economics, continued urbanisation and a reduction in traditional employment opportunities has seen a rethink in the long-term rehabilitation outcomes. The community has recognised that the rehabilitated site will provide the basis of a viable tourism venture and the creation of a Heritage and Art Park (working title æGolden Point ParkÆ) is the culmination of that process.

Jan 1, 2002

Geological information plays a significant, cost effective role, in the Mt Whaleback iron ore mining operations. The geology and structure are complex. Good communication between the Mine Planning Production Scheduling and Quality Control Sections is the key to utilisation of geological information to its full potential.Drilling and pit face mapping are the two basic sources of detailed data sets which are processed to prepare up to date geological cross sections and benchwise geological plans. This information is used directly for the blast pattern design and production scheduling. Physical ore type estimation is also undertaken. Orebody models are generated from the geological information.

Jan 1, 1990

By Gregory L. M, Phillips G. N

Although it has long been recognised that there is a diversity of minerals associated with Victorian gold deposits, the degree to which this mineralogy is systematic or haphazard has remained uncertain. Recent work by the authors and students under their supervision permits a sharp delineation of the boundaries between different mineralogical domains, and these are interpreted in terms of recent rapid advances in Victorian tectonics, and the regional framework of Victorian gold geology described in Phillips and Hughes (1996).

Jan 1, 1997

The Mineragraphic Section of the Council for Scientific and Industrial Research has had occasion from time to time to examine rocks, ores and concentrates from the Yatukoula goldfield, Fiji. The results of the examinations have been supplied as Mineragraphic Reports and have been supplementary to various investigations carried out by the mining companies on ore treatment, or by visiting geologists on the nature of the rocks and lodes. The presence of tellurides was determined in 1935, though incorrectly as nagyagite. The general absence of lead, except in traces, was soon afterwards discovered, and it came to be recognised as the mines were opened up that the chief telluride minerals on the field were sylvanite and native tellurium. Specimens of the tellurides have been provided from time to time by E. G. Theodore, Managing Director of the Emperor Mines Ltd., and of the Loloma (Fiji) Gold Mines N.L., and further material was recently obtained, as the result of a visit to the field at the invitation of Mr. Theodore.The aim of this paper is to describe the occurrence of the tellurides in these specimens. The work has been carried out as part of the programme of research of the Mineragraphic Section.THE VATUKOULA GOLDFIELDThe Emperor, Loloma and Dolphin mines are situated at Vatukoula, six miles, south of Tavua, on the north coast...

Jan 1, 1949

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

The Crown Minerals Act 1991 has introduced some significant changes to the New Zealand mining industry, not the least of which relate to the ability of miners to obtain access to land to conduct mining activities. This paper briefly reviews the relevant provisions of the Crown Minerals Act dealing with access arrangements, considers some typical features of access arrangements and examines a number of areas where problems may arise.

Jan 1, 1992

By Jowett A

To compare open circuit lead primary rougher results at Mount Isa Mines Ltd., eleven surveys were made over five weeks of plant operation with varying ore sources, including a specially hauled sample of 100% Black Star ore. Three of the surveys which represented extremes in performance were selected for sizing, cyclosizing and assaying for lead, zinc and iron. A comparison of the flotation kinetics has revealed the similarities (including common problems) and differences for the surveyed ores. The concepts of entrainment and collectorless flotability are used to aid interpretation of the kinetic data.

Jan 1, 1978

A methodology for the fatigue life estimation of load haul dumpers, employed in underground platinum mines, has been developed and applied. This method entails the quantification of operating conditions by means of stress measurements. The measurements are then translated into a fatigue loading factor for a finite element model. The results of this analysis are then used to compare all the critical connections in the structure to detail categories in relevant fatigue codes, and predict a life in operating hours for the vehicle structure. The method was applied on a specific model and the results of this analysis were compared to actual failure occurrences with reasonable accuracy. It is intended that the methodology be embedded into performance specifications and purchasing contracts and that technology transfer to OEMs be achieved. Based on the experience of this project and other similar exercises it is estimated that structural life expectancies may be increased across a typical fleet of trackless mining vehicles (LHDs, drill rigs, utility vehicles, dump trucks) by at least 20 per cent.

Jan 1, 2005

Legislation up to the early 1950s prevented the mechanical extraction of pillars. The mines operating at that time had formed extensive areas of pillars. When permission for the mechanical extraction was gazetted, conventional equipment was employed for pillar extraction and generally using hand mining systems. The mid-fifty's saw the of continuous miners. These machines eliminated the disadvantages of conventional equipment and the necessity for multiple working places. Some new layouts for panels emerged; however, actual extraction methods of pillars still followed closely that of hand mining. During the early sixty's the extraction of standing or new formed pillars was undertaken by the "open-end lift" or a "split and lift" method.

Jan 1, 1974