Search Documents

By Bisshop J. P W

Maximum recovery of sulphide minerals by flotation is achieved over a limited size range. Valuable particles above and below this range have a smaller probability of being recovered. In the normal grinding-flotation operation, not all valuables are reduced to the optimum size range, and therefore sub- stantial losses occur. A significant improve- ment in the size distribution is not usually possible within the conventional circuit, and a more complex arrangement may be necessary to obtain optimum recovery of the valuable mineral. This problem is considered with refer- ence to the Mt. LyeZl concentrator. The performance of the existing circuit is dis- cussed, and it is shown that losses in recovery occur in both coarse and fine sizes. Laboratory tests indicate that regrinding the coarse particles results in an increase in recovery of up to 4%. Redistribution of plant grinding capacity to reduce initial grinding power by 6% and use this capacity to regrind coarse particles was considered. It is con- cluded that overall plant efficiency would be increased by 2% provided that overloading of the regrind mill could be avoided.

Jan 1, 1977

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

Lateritic nickel ore occurs as a supergene or residual deposit as a result of the tropical weathering of underlying ultramafic rocks. The mineralisation may be as hydrated Ni-Mg silicates, like garnierite (silicate ore); or as hydrated Ni-Fe oxide (oxide) ore. Non-sulphide ore represents only 30% of the tonnage mined, but represents 85% of the total world's nickel reserves. A typical lateritic profile consists of 4 zones above the unweathered ultramafic parent rock: Zone 1: the "upper laterite" which is dark red-brown, porous and concentrically structured. It contains 0.2 to 0.8% Ni, 48.0 to 72.0% Fe, and 0 to 9.5% MgO. It is often capped by a ferricrete crust. Zone 2: the "middle laterite", which is red-brown to light brown and more porous than the above zone. It contains 0.8 to 1.5% Ni, 42.0 to 48.0% Fe and 0.5 to 6.0% MgO. Zone 3: the "basal laterite" which is yellow-brown to yellow-orange,

Jan 1, 1974

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

Over the last ten years geological and mining software products have evolved greatly. Software companies developing such products have focussed almost exclusively on the development of technical aspects of the applications, addressing geological, ore reserve estimation and mine planning problems. These specialist applications, and the many other new technologies that are being developed by a myriad of niche developers, are an essential part of todayÆs hi-tech mining operations. Technology is also being used in many other areas to improve the mining process and there is no doubt that tremendous advances are being made in all these fields. Yet there is something missing. The manner in which the technologies are used and implemented has led to the creation of many independent and inefficient æislands of technologyÆ where a variety of products from different vendors are used to address different, but related problems. Problems occur with unreliable information, data duplication, data redundancy and transferring data between applications that may be incompatible or even run on different computer platforms. These problems impede the flow and availability of information and hamper day-to-day decision-making by mine management. A solution to this problem is to take a holistic view of all the various technical applications and incorporate them into a single information technology solution. This solution must encompass all of the information requirements of a mining operation and must provide facilities that address much of the modern thinking about mine management, including strategic mine planning, value management, key performance indicators, and maintenance of a mineral balance sheet. Gemcom is developing an Integrated Resource Asset Management System (IRAMS), which is an enterprise-wide integrated computer system that encompasses various applications typically found at a mining operation. The core component of the system is a common, open, industry standard database that can be shared by many users from each of the different departments at a mine. Around that central repository are the primary applications that provide the mine with information it needs to operate. Ensuring that the information is reliable, accurate, shareable, timely and consistent will eliminate many inefficiencies, and provide significant benefits to mining companies. In turn these benefits will lead to significant improvements in decision-making, productivity and profitability for the operation. The initial version of the IRAMS system is currently being implemented at the De Beers Venetia Mine in South Africa. The system is being built around a core repository using the Microsoft æBack OfficeÆ architecture, and incorporates key technical applications from Gemcom, Whittle, De Beers Technical Team, Wenco and JKTech. The benefits of enterprise-wide systems have long been recognised in the commercial arena and enterprise resource planning (ERP) systems such as SAP, JD Edwards and MIMS are becoming commonplace in the mining industry. The more forward looking software developers and mining companies realise the need for efficient management of the information gathered during the mining process and can see that the concepts used in ERP systems apply equally to the technical applications as they did to commercial applications. The use of IT in the mining industry has expanded tremendously over the last five years as enabling technology and management acceptance has become more prevalent, and there is considerable room for dramatic growth over the next five years. The evolution of geological and mining software has now reached the stage where mines will yield the greatest returns by integrating the applications used in each area of their operations.

Jan 1, 1999

By A Madera, R Watt

The Tampakan deposit is a strongly telescoped high-sulphidation-epithermal/ porphyry deposit pair which is hosted by a sequence of probable Pliocene age subaerial andesite flows. These host units lie on the western flank of a deeply dissected andesitic stratovolcano within the northernmost portion of the Sangihe Arc in southern Mindanao. The deposit was discovered by WMC geologists in 1992 and is currently undergoing resource evaluation. Preliminary resource estimations indicate a total inferred metal content of 12 million tonnes of copper metal and 16 million ounces of gold. Using a 0.2 per cent Cu cut-off grade, the deposit has a current mineral resource of approximately 2.5 billion tonnes with an estimated grade of 0.48 per cent copper. At a higher cut-off grade of 0.5 per cent Cu, the mineral resource is approximately 900 million tonnes with an estimated grade of 0.75 per cent copper. Mineralisation is open both to the west and at depth. The Tampakan district is centrally located with respect to a 100 km wide zone of left-lateral strike-slip deformation represented by the trans-Mindanao Cotabato Fault Zone. The district is transected by several WNW-striking wrench faults which represent strands of the regional Cotabato Fault Zone. High-sulphidation epithermal mineralisation within the Tampakan deposit is strongly controlled by NNE-trending faults which lie along a dilational orientation within the Pliocene stress field associated with the Cotabato strike-slip fault zone. The mineralisation is broadly hosted by a gently-dipping, tabular zone of partial to massive silicification which displays multi-phase brecciation, acid-leaching, related vuggy porosity and which is developed within a district-scale advanced-argillic and argillic lithocap exceeding 90 km 2 in area. High-sulphidation epithermal mineralisation is associated with a silica-pyrophyllite-dickite-alunite-diaspore¦sericite alteration assemblage which is transitional downward to sericite-chlorite alteration and relict potassic biotite-chlorite-magnetite-anhydrite alteration associated with pervasively developed but weakly mineralised porphyry quartz stockwork veins. The high-sulphidation mineralisation is dominated by disseminated, vein and vug-filling enargite-bornite-digenite-chalcocite-covellite ¦ molybdenite which has overprinted an earlier phase of porphyry copper stockwork veins associated with high-level porphyritic hornblende diorite stocks. The distribution of high-sulphidation alteration and mineralisation reflects strong stratigraphic and structural controls. The high-sulphidation mineralisation covers a surface area of approximately 1.6 km by 2.0 km and forms a tabular, flat-lying to gently-dipping body between 200 and 500 metres thick. It is intersected at RL-1200 m ASL (at surface) in the northern portion of the deposit and extends down to RL-600 m ASL at the southern end. The deposit has been diamond-drill tested to a depth of 400 - 500 metres where low-grade chalcopyrite-bornite-pyrite mineralisation is hosted by pervasive quartz stockwork veins. This deep-level mineralisation represents the outer portion of a porphyry Cu system hosted by both andesite flows and the uppermost portions of high-level hornblende diorite stocks. Deep drilling to test for higher tenor porphyry Cu mineralisation is planned.

Jan 1, 1999

By T E. Jeffries, M Zentilli, J STguel, C C. Wilkinson, B G. Rusk, V H. Vry

Laser ablation Inductively Coupled Plasma Mass Spectrometry (ICPMS) analysis of fluid inclusions trapping mineralising solutions in major porphyry-copper deposits indicates that copper concentrations can reach 103 - 104 ppm in both dilute, CO2-bearing fluids and in high salinity brines. Non-Cl transport of Cu is implicated. Au has been determined at 0.2 - 0.4 ppm in the low salinity fluids and may be co-transported with Cu. In contrast, high concentrations of Fe, Mn, Zn and Pb are only attained in brines and correlate strongly with Cl-indicating chloride transport. Physical and/or temporal separation of these fluid types can therefore producemetal fractionation within porphyry systems. Evidence concerning the behaviour of Mo is less clear but brine transport appears to be favoured; phase separation is one mechanism that may account for the fractionation of Mo from Cu and the formation of quartz-molybdenite veins. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Fuerstenau DW

The flotation of pyrite in ethyl xanthate solutions is presented along with electrokinetic results. The results have been analysed in view of recently published thermodynamic calculations as well as other published data on the pyrite-xanthate system including adsorption and voltarnmetry studies. The flotation response of pyrite in xanthate solutions is characterised by two maxima, one at pH 4 and the other at pH 8-9. The acidic maxima is also associated with a reversal in the electrophoretic mobility of pyrite, probably due to the formation of ferric xanthate on the pyrite surface through chemisorption of xanthate ions while the basic maxima is not associated with major changes in the mobility and flotation at this pH can probably be attributed the adsorption of dixanthogen. It is concluded that there is not sufficient experimental evidence to conclusively attribute the lack of flotation response in solutions at near neutral pH to any particular phenomena, either kinetic or thermodynamic.

Jan 1, 1993

By N Anderson

The world-class Golden Mile gold deposit in the Eastern Goldfields of Western Australia is part of the Kalgoorlie Consolidated Gold Mines (KCGM) operation, which is wholly owned by Northern Star Resources Limited. Current mining operations across the Golden Mile is dominated by the large Fimiston Open Pit, which is over 4 km long, 1 km wide and 600 m deep. It is part of a larger mineralised system that stretches over 8 km and includes the Mt Charlotte Underground Mine, which is also operated by KCGM, as well as numerous historical open pit and underground mines. This mineralised system has been continuously mined for over 125 years and is set to continue well into the future. The Golden Mile deposit is in the Norseman Wiluna Greenstone Belt which is made up of a series of mafic volcanic and sedimentary rocks that have been structurally deformed and intruded by granitic rocks. There are two main styles of mineralisation across the Golden Mile. Firstly, the Fimiston style, which consists of shear hosted Golden Mile lodes with abundant sulfides and tellurides and secondly, the Charlotte style that comprises younger stockwork veins. Fimiston style mineralisation is the primary style of mineralisation within the Fimiston Open Pit. Historically, in excess of 3500 m of underground development and over 755 stopes were mined prior to the consolidation of the area and the commencement of Fimiston Open Pit operation. Old underground workings, known as voids, are either empty or backfilled and extend to more than 1.2 km below surface. Although they are a routine part of mining operations at KCGM, voids pose a significant challenge for the geology team in terms of planning and executing exploration and grade control drilling, geological modelling, grade and tonnage estimation, drill and blast design and execution, marking up ore block designs, mining, and reconciliation. This paper will discuss the various challenges faced by the geology team due to the presence of voids, solutions used to overcome some of these challenges and the results of these activities.

Mar 22, 2022

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

By Ito H, Noguchi F, Ueda Y

DTA curves of synthesis lead sulfide and commercial. lead concentrates during oxidation were measured to clarify the mechanism of ox- idation of lead sulfide. The oxidation reac tions could be divided to elementary reactions with production of basic lead sulfates such as 2PbO PbSO4. An existance of iron sulfide played an important role of the oxidation of lead concentrates. The oxidation rates of lead sulfide were measured in the wide range of oxygen potenti- als using IR type SO2 gas-meter. The oxidation rates under low Po 2 which corresponds to the direct oxidation smelting were much lower than those obtained under high Pot. The combustion temperatures of lead sulfide were also measured by hot thermocouple method. Those values were extremly low compar- ing the oxidation temperatures obtained by DTA.

Jan 1, 1987

By Holliday RJ

The Imperial Smelting Furnace (ISF) was developed in Britain during the 1950's as a process which could produce zinc from a blast furnace. Since then it has evolved into an efficient means of producing zinc and lead from lower grade raw materials, both of primary and secondary origin. These changes have been in response to the need to improve the cost competitive position of the ISF in a climate of decreasing metal prices. The improvements at the Cockle Creek smelter of Sulphide Corporation Pty Limited have resulted from work undertaken in four main areas: 1. Changes in plant design and operating practice to give more stable furnace operation. 2. Improvements to the quality of sinter being charged to the furnace. 3. Improved monitoring of process variables and the formulation of control strategies based on the improved data. 4. Increased understanding of the processes occuring within the furnace shaft to allow predictive modelling to be undertaken. Work in these areas is still progressing but the work to date has resulted in a significant improvement in the production rate and efficiency of operation.

Jan 1, 1984

By G T. Hefter, P Singh

Sulphur dioxide oxidation is an attractive alternative anodic reaction to the evolution of oxygen in copper electrowinning. Accordingly, the electrochemical oxidation of SO2 in aqueous 1.0 x 10-1 mol/L NaClO4 has been studied at pH 2.3 using platinum and glassy carbon electrodes. On the platinum electrode SO2 oxidation occurred on the forward scan at 0.96 V and on the reverse scan at 0.63 V. For GC, a single SO2 oxidation peak occurred at 1.40 V on the forward scan. SO2 oxidation on both electrode substrates was hampered by oxide layer formation. The electrode could be reactivated however, by oxide layer reduction. Although reactivation was most successful for platinum, SO2 oxidation on platinum is quite complex, with this evidenced by the reverse scan anodic peak. Glassy carbon shows simpler behaviour and thus, is the preferred substrate for SO2 oxidation.

Jan 1, 1998

Universities have had a long history in the education of geology graduates, Analysis of this history reveals a record of success, as judged on a world basis. However there have been significant changes in the last 20 years that have impacted on the ability of universities to continue to provide their traditional style of geology education. These changes have increased in the last 10 years. In the teaching side, there has been a change in expectations. Additionally the increasing workload decreases the value of each academic to perform the tasks needed by the new education. In the area of research, the funds provided have continued to decline, in both real and absolute terms, and it is now necessary for universities to seek out funds to pay for their postgraduate research. Additionally, the universities have slipped into the error of what cahn only be termed "academic incest", and research student mobility has decreased to an undesirable level, stifling initiative and new ideas in a number of cases, The only solution is for Government monies to be "directed" - ie that the postgraduate student must leave his or her original university in order to receifve the research stipend/scholarship. On the government front, the government and its agencies have not adequately analysed and recognised the need for the redirection of education and research funds into the needy areas of science and technology, especially those that related to the minerals area.

Jan 1, 1986

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

By X Li, W McKeague, M S. Powell

This paper explores the importance of operators in the overall efficiency of mineral processing plants. With the potential of future control configurations becoming more remote, it is time to review the implementation of control and utilisation of operators. This paper is based on a preliminary review of operators and control room operations and clearly shows that, in the minerals industry, operations are typically run in a reactive mode (with a focus on ensuring equipment operation), rather than in a proactive mode (with a focus on optimising the process performance). The primary reason for this misguided approach is the short sighted thinking applied to the challenges of designing technology and organisational tools capable of addressing the essential operational needs: an approach which inevitably results in a disconnect between people and technology. Contrary to the popular approach of replacing operators with expert systems, the thesis of this paper is that the shift to more complex circuits, with higher demands on processing capability and control, will require the actual upskilling of operators. Experience in mineral processing and other industries indicates that expert systems cope well with small changes but are typically unable to respond to major changes in feed material and this is where the expert operator becomes crucial. Providing operators with ongoing high level training in process understanding, and restructuring how they interact with the plant and interface with the control system is the approach being proposed here - an approach surprisingly underutilised and often absent in the minerals industry today.CITATION:Li, X, Powell, M S and McKeague, W, 2012. Unlocking processing potential by empowering our operators, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D Sibthorpe

The employment of a tunnel boring machine (TBM) is the default delivery method for the realisation of traffic, utility and primary resource underground space worldwide, with hundreds of kilometres completed safely each year. This is not yet the case for the mining sector in Australia, specifically underground coal mining. The safety advantages of TBM delivery when compared to New Austrian Tunnelling Method (NATM) delivery, or that of drill and blast, remains unrealised.With coal access drifts ranging between 1000?m and 3000?m in length, the construction of these facilities using TBMs could be done in a fraction of the time when compared to current practice. TBM world records currently stand at 435?m/week or 1600?m/month for the 7.0?m to 10.0?m range. Resource owners and developers should embrace the opportunity to deliver access to their orebodies in only a few months, excluding machine assembly and disassembly time.There are challenges in utilising TBMs for construction of Coal access drifts, such as; TBMs generally being bespoke design, maximising capital efficiency for drift development, and geotechnical variances between projects. This paper explores safer and more cost-effective options. This paper also provides detail of how the configuration within a completed drift could be optimised to ensure all site specific needs are met with regard to future use of the drift. The paper also includes descriptions of the engineering solutions that are available for physical and atmospheric challenges specific to coal drift applications and how the TBM manufactures are adapting to the regulatory requirements are also covered.Due to downward pressure on high cost bases and ever increasing safety requirements the popularity of TBMs in the Australian mining sector can be expected to increase and eventually become the default delivery method for coal drift construction, building them cheaper, faster and?safer.CITATION:Sibthorpe, D, 2014. Coal drift construction by tunnel boring machine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 671–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014