Search Documents

The low grade Mount Charlotte orebody was first mined with minimum capital expenditure by mechanised cut and fill stoping. The lower block was prepared simultaneously for open stoping by shaft sinking and installing another crusher and services. Similar development for the third block was discouraged by economic factors and reduced tonnage. Decline develop- ment required less capital and opened up ore reserves commensurate with advance, providing flexibility to stop operations without commit- ment: A 1 in 7 decline measuring 4.25m x 5.5m to accommodate standard Euclid 25 tonne dump trucks was developed south of the orebody. A fleet of four trucks average 12 loads each per shift over a haul distance of 700m.

Jan 1, 1973

By Kyle J. H, Browner R. E

The selective adsorption of gold cyanide by the weak base ion exchange resins, PAZ-4* and Duolite A-7*, the neutral polymeric adsorbent, Amberlite XAD7*, and the strong base resins, PAZ-8 and IRA-400+ have been studied in both low and high salinity waters, and performance compared with activated carbon. The selectivity of the neutral polymeric adsorbent and activated carbon for gold decreased in highly saline water, while the selectivity of weak and strong base resins for gold increased in highly saline water. This supports the contention that the adsorption mechanism for neutral polymeric adsorbents and activated carbon is the same. Copyright

Jan 1, 1992

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

By Karlson R, Rispin M

Chemical admixtures are not commonly included in the variety of backfill mixes used in the mining industry. This may be attributed to several reasons including, but not limited to: the perceived high added cost, 2. the lack of awareness about their proper use, and 3. the lack of knowledge about their features and benefits. In the construction industry today, however, chemical admixtures are used in the majority of the concrete produced, enabling concrete to become a more cost-effective building material. They also enable construction crews to meet demands for year-round construction, quicker completion of construction projects, and improved concrete properties. The high demand for chemical admixtures in the construction industry has led to numerous innovations in admixture technology in recent years. Some of these chemical admixtures have been found to enhance the production, transport, placement, and in situ properties of backfill mixes. Others have been found to reduce the cost of such mixes while maintaining, and in some cases improving, their physical properties. In this paper, a few of such innovative admixture technologies are discussed. The benefits, imparted by these technologies to backfill mixes as well as performance data on their use in several backfill applications at various mines, are presented.

Jan 1, 1998

By O Arafat, K M. Bartholomew

A voracious consumer of energy and grinding media, the modern ball milling circuit has a huge direct cost impact on a mineral processing operation. Through optimisation, grinding also has the potential to unlock great improvements in recovery and throughput, but how can the complex interactions between mills, classifiers, tonnage, ore-type and downstream recovery be measured, understood and managed in a systematic manner?Functional performance analysis provides the tools and insights needed to measure, understand and improve the two key process efficiencies in ball milling circuits: classification system efficiency (CSE) and mill grinding efficiency.CSE measures the composite performance of the classification system as a whole. In short, the purpose of the classification system is to ensure that grinding mill energy is used to grind coarse particles while minimising overgrinding. CSE is simple to measure in the plant and it provides immediate feedback to the plant metallurgist, mill superintendent and management about the performance of the classification system and the amount of wasted energy in the grinding plant.Mill grinding efficiency measures the capacity of the grinding mill to convert feed-sized material into product-sized material on a tonnes per kilowatt hour basis. It is normalised based upon the ore resistance to breakage, so it provides feedback about the ‘health’ of the milling process under varying operating conditions and ore types. Mill grinding efficiency is measured at the same time as CSE through circuit sampling.Functional performance analysis combines CSE and mill grinding efficiency to provide a measureable, manageable optimisation objective. It also provides a link to tonnage, ore type and recovery. As a result, systematic optimisation of a grinding circuit is a measureable and manageable process to meet business objectives.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2014. Functional performance of ball milling circuits – a plant metallurgist’s tool for process characterisation and optimisation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Bradshaw, J R. R de Villiers

The non-stoichiometric sulfide mineral pyrrhotite (Fe(1-x)S), common to many nickel and platinum group element (PGE) ore deposits, occurs in varying crystallographic forms with the different types exhibiting subtly different physical and chemical properties. These differing properties are likely to influence the flotation performance of pyrrhotite, which in the case of PGE operations is actively recovered, whereas in nickel operations pyrrhotite is depressed. In this study, examination of natural pyrrhotite samples from Southern African and Canadian nickel and PGE ore deposits revealed a variety of pyrrhotite compositions in terms of iron content (Fe7S8, Fe9S10, Fe11S12) and solid solution nickel concentration. Pyrrhotite composition was correlated with its mineral association depending on whether non-magnetic pyrrhotite occurred in conjunction with troilite, non-magnetic pyrrhotite occurred as single phase pyrrhotite, magnetic pyrrhotite occurred as single phase pyrrhotite or whether the two phases; magnetic and non-magnetic pyrrhotite co-exist. Subsequent microflotation tests of selected single phase pyrrhotite samples revealed that the non-magnetic pyrrhotite is slightly more floatable than magnetic pyrrhotite. Microflotation tests also showed that varying flotation responses occur between differing magnetic pyrrhotite samples. These differences in flotation performance are postulated to be a result of the effects of varying pyrrhotite crystallography, trace metal content and mineral association on pyrrhotite oxidation, formation of surface species and subsequent adsorption with xanthate collector.

Jan 1, 2008

By B Murphy, J L. Heath

Installation of flotation equipment is a lengthy and intricate process involving conceptual design, detailed design and layout, equipment installation, equipment commissioning and handover prior to the plant commencing operation. During these steps, mistakes are often made that lead to increased costs and/or schedule delays in bringing the new equipment online.This paper presents a series of recommendations for the installation and commissioning of flotation equipment to minimise mistakes and ensure that plant production commences efficiently with a minimum of resources. The advice herein is based on lessons learnt from recent flotation equipment commissioning. It is intended as resource material for flotation plant designers, construction contractors, metallurgists and operators, and is applicable to both new and existing plants.CITATION:Heath, J L, Murphy, B and Bourke, P, 2014. Effectively installing and commissioning flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 399–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Mitchell

Jetcrete Australia Pty Ltd, shotcrete contractor took the initiative in 2008 to discontinue the use of ‘road registerable’ concrete trucks for all underground works in Australia and internationally.The rationale for this decision was basic, safety. Historically these vehicles have been and still are involved in far too many accidents; this obvious trend needs to be addressed by engineering out the root cause of the problem which in this case is suitability for purpose.Road registerable concrete trucks have been widely used for the delivery of concrete in Australian mines for many years prior to and after the inception of wet shotcrete as ‘in cycle’ ground support in underground excavations around 1992. With this inception came a wide interest in the shotcrete process and an influx of new shotcrete contractors, all using road registerable concrete trucks to deliver the large volumes of Shotcrete required for these services and in turn largely increasing the use of these vehicles underground. The road registerable concrete trucks were difficult to control and each trip underground required the operators to maintain good management of the inherent risks. We virtually had no reasonable alternative for the industry and could only encourage the operators to drive with soft controls such as, reducing overall speed to a maximum of 15 km per hour when declining, regardless of the road conditions, coming to a complete halt prior to turning into any sharp corners, remaining in the same gear both inclining and declining.

Mar 21, 2011

By A Weeks, W J. Shaw, A Kuk

Grade control is a process that requires the interaction between many components of the mining operation and successful grade control is only realised through good data, robust systems, and a well-trained, motivated and disciplined workforce.The Mt Magnet Gold Project Pty Ltd (MMGP), a wholly owned subsidiary of Ramelius Resources Limited, started mining at Mt Magnet in February 2012 with high expectations for success. Positive cash flow would fund an aggressive exploration and mine development program in the area to increase mine life. Disappointment followed when after start-up the operation had issues achieving budget grade and realising the predicted grade of the mined ore. In January 2013, things started to improve. During the next six months, gold production steadily increased with successive months achieving record production. What had changed?Improvements started following the realisation that controlling grade was not the sole responsibility of the mining geologist and that everyone on-site has a role to play. This paper examines the factors that delivered success for MMGP.CITATION:Weeks, A, Shaw, W J and Kuk, A, 2014. Who is responsible for grade? – an evaluation of the value chain at Mt Magnet Gold Project, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 477–482 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

The Goonumbla district of central-west New South Wales, Australia, hosts four significant porphyry Cu-Au deposits that contain a combined probable ore reserve of 71.7 million tonnes at 1.2 per cent Cu and 0.5 g/t Au. Mineralisation in the Goonumbla deposits is associated with narrow, pipe-like intrusions of quartz monzonite porphyry, in which several intrusive phases have been recognised. Five textural characteristics have been used to distinguish the various intrusive phases recognised in the Goonumbla porphyry deposits: (1) phenocryst abundance; (2) nature of the groundmass; (3 and 4) proportion and mineralogy of the mafic and non-mafic phenocrysts; and (5) the presence or absence of anhedral quartz grains in the groundmass. In addition, each intrusive phase is classified according to its estimated original quartz, alkali feldspar and plagioclase contents. Features common to all of the intrusions are that they contain two types of plagioclase and two or three types of K-feldspar phenocrysts in variable proportions. Most of the intrusions also contain apatite micro-phenocrysts. The groundmass textures range from aphanitic through granular to euhedral K-feldspar in a quartz matrix. With only one exception, all of the intrusive phases recognised are either quartz monzonite porphyry or mafic (>5 per cent mafic minerals) quartz monzonite porphyry. The exception is a biotite - phyric monzodiorite, which occurs in the basal portions of one of the deposits. Textural variants of intrusive phases at Goonumbla have been investigated to establish whether specific combinations of characteristics indicate mineralised intrusions, while others suggest barren ones. Some correlations between intrusion types and Cu and Au grade have been recognised. The most important textural characteristic that relates to high grade mineralisation appears to be the low proportion of mafic minerals, because the quartz monzonite porphyry intrusions hosting most of the mineralisation in the two deposits studied contain

Jan 1, 1999

Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health rleterinratinn_

Jan 1, 1988

By Swann CA

In order to meet export sales requirements from 1983 onwards, Amcoal developed a new underground mine in the Witbank area of the Transvaal. The mine was required to produce 5 million tons of run of mine coal per annum giving rise to 4 million tons of saleable products. A description of the coal processing plant is given with comments on design philosophy and design parameters. Main features of the coal processing plant are the raw coal handling facilities, centralised control and data capture and the loadout station. The management systems applied during the commissioning period are described. The difficulties experienced and their solutions are discussed. Commissioning was concluded with an independent plant performance test.

Jan 1, 1986

By A Murphy

Mining plants and infrastructure, and the decisions made by their designers, can have large impacts on their environmental and social context, commonly referred to as the site or plant footprint. They can also be the source of constructive contributions to sustainable development when designers are enabled via the information, systems and tools to incorporate sustainability in engineering processes. A facility’s footprint and the project’s contribution to sustainability – economic, environmental and social aspects – are now key considerations in regulatory approval processes and are the fundamental drivers of support, or opposition, from the project’s stakeholders.Historically, plant and infrastructure designers have not been well integrated with the environmental and social professionals who are engaged to pursue regulatory approvals. Despite this, many objectives central to technical and process engineering have in fact contributed positively to a facility’s footprint and indeed its contribution to sustainable development. Examples of these objectives include increasing process and energy efficiency, and minimising the quantities of waste requiring disposal. With the framework of sustainability, mining plant and infrastructure designers are indeed at the forefront of incorporating sustainability into resource industry projects and are central to the process of obtaining regulatory approvals and ongoing stakeholder support. The process of incorporation starts with a shared understanding of sustainability and sustainable development, and continues with project processes that facilitate information and knowledge exchange throughout the project life cycle.CITATION:Murphy, A, 2014. Incorporating sustainability into mining plant and infrastructure design, in Proceedings Life-of-Mine 2014 , pp 637–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Ehlers HK

Mount Isa Mines Limited has 25 rod and ball mills of various sizes installed in two Concentrators at Mount Isa. A continuing investigation into installation, design and materials of liners for these mills has been in progress since the early sixties. Both manual and mechanical methods of liner installation are used and described. Materials for the various applications have been evaluated, mainly by field trials. Design of liners has also been evaluated by field trials and the history of trials in No.4 Concentrator is given. The purpose of the investigation has been to reduce the cost of mill lining and the life of many linings has been greatly increased as a result of this work.

Jan 1, 1978

By Willett, Jacka

Group 3 were asked to discuss the treatment of spontaneous combustion. Before discussing specific cases we agreed that certain preliminary information should be available. The following questions are typical of the information which might be requested: 1. Have workmen been withdrawn? 2. Have gas samples been taken? 3. Is the mine gassy? 4. What are the details of water supply? 5. Are mine plans available? 6. What equipment is available? We discussed treatment in four different circumstances as follows: 1.

Jan 1, 1973

By Prohaska G, Jackson F, Jack B

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By T Y. Ko, Y S. Kang, S J. Park, J H. Hwang

The lunar subsurface, particularly the lava tubes formed by ancient volcanic activity, presents a promising environment for establishing safe and sustainable human habitats on the Moon. Tunnel Boring Machines (TBMs), widely used for excavating tunnels on Earth, offer a potential solution for developing these subsurface spaces. However, the unique lunar conditions, including extreme temperatures, high vacuum, radiation, and the extraordinary strength and abrasiveness of lunar rocks, necessitate significant adaptations to existing TBM technology. This study investigates the feasibility of utilising TBMs for lunar subsurface exploration and base construction, addressing the challenges posed by the harsh lunar environment. We review previous conceptual designs for lunar TBMs, highlighting their strengths and limitations in addressing these challenges. Additionally, we explore innovative excavation methods, such as microwave-assisted rock weakening and undercutting techniques, to enhance the efficiency and effectiveness of lunar TBM operations. By evaluating the geological characteristics of the lunar crust and analysing the potential of lava tubes as launching points for TBM operations, this study provides a comprehensive assessment of the technical requirements and operational considerations for lunar TBM implementation. The findings of this research contribute to the growing body of knowledge on lunar base development and pave the way for future human exploration and utilisation of the Moon’s subsurface resources.

Sep 1, 2024

The Energy Authority of NSW has wide powers and responsibilities conferred by its Act which are pertinent to the State's coal industry and its development into the next century. With respect to coal, the broad objective is to maximise the benefits to NSW and its people derived from the State's coal resources. The initial focus of the Authority's coal-related activities in the late 70's and early 80's was on petroleum substitutes from coal. Research was supported, especially on hydrogenation, and the Authority participated in the Joint Australia/Federal Republic of Germany coal-to-oil feasibility study. It also co-ordinated a State Government initiative to involve the private sector in examining the possible establishment of a synthetic fuels industry based on Hunter Valley coal. With a short-fall in world-wide petroleum supply now seen as less likely for some years, the Authority is looking also at ways of working towards the broad objective in the field of coal utilisation on both domestic and export markets. Areas of interest include possibilities for using washery rejects, means of making NSW coal more competitive as an energy source, use of coal-seam gas and new or special technologies for burning coal. The future is expected to see renewed interest in producing petroleum substitutes, and coal - as the State's major energy resource - is seen as a strong contender as a basis for such an industry. Developments in coal-based power generation are also expected to have an impact, with advanced technologies having a possible place here as well as Overseas.

Jan 1, 1987

By P Trotta

The majority of water to the Olympic Dam mine and the nearby townships of Roxby Downs and Andamooka is supplied from the Great Artesian Basin (GAB). There are no permanent local water sources available to Olympic Dam. The use of water from the Great Artesian Basin by Olympic Dam receives considerable attention by BHP Billiton and is extensively regulated by the Government of South Australia. Olympic Dam has robust business management systems in place to ensure the sustainable use of water from the GAB including ISO9001 and ISO14001 systems to deliver the targeted outcomes and obligations of the Olympic Dam Environmental Management and Monitoring Program. The management systems ensure that Olympic Dam retains accountability for its water demand from the GAB over the life of the mine. This accountability has delivered continuous improvement in water use efficiency driven by operating discipline, implementation of water saving projects, using water on a fit for purpose basis including substitution from non-GAB sources, and risk management to prevent and mitigate water supply disruptions to Olympic Dam and Roxby Downs. Since the establishment of Olympic Dam, BHP Billiton has funded a reduction in GAB water flow from bores, previously going to waste, that is greater than the annual average flow used by Olympic Dam.

Jan 1, 2009

This paper will first discuss the fundamental requirements for reliable discharge of backfill by gravity alone at high per cent solids. This discussion will include brief mention of the underlying principles of saturated solids flow contrasted to that of stirred tank or dilute discharge systems. Here the need to possess full knowledge of the flow properties of the stored material will be highlighted. In addition proper account must be made of the silo overflow weir and settling capacity to match plant throughput. Here opportunity will be taken to highlight the complexity of this multi-phase flow situation as well as the general yet paramount requirements for reliable solids flow. It will be shown that by proper attention to the multi-phase considerations gravity discharge of slurries as a consolidated bed with minimal water content is possible. Such high solids discharge results in greatly reduced demand for process water. In addition pumping costs are reduced as is the delay time associated with the mine drainage operation. Confirmation of successful applications will be highlighted by reference to several recent case studies. In the concluding phase mention will be made of the key yet very simple and effective operation techniques which enhance reliable discharge. The simplicity and reliability of properly designed gravity discharge backfill tank systems suggests increased application of this technology by the mining industry.

Jan 1, 1998