Search Documents

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Michaelsen, S Miller

The Grasberg Mine is a copper and gold open pit mine operated by PT Freeport Indonesia (PTFI) and located in the high equatorial mountains of the Indonesian province of Papua. The climate is alpine/subalpine with little seasonal variation in temperature or rainfall. The daily average temperature ranges from about 2¦C to 14¦C and the annual rainfall in the vicinity of the mine and overburden stockpiles is about 4000 mm to 5000 mm. Mining of the Grasberg open pit will continue until 2014 at which time approximately 2750 Mt of overburden will have been produced. Current overburden production rates are 200 Mt per annum. The current mill rate is 230 000 t/day from the Grasberg pit (190 000 t/day) and the underground operations (40 000 t/day). The acid rock drainage (ARD) issues associated with overburden from the Grasberg operations were identified early in the mining operation. Almost all overburden placed to date has been Potentially Acid Forming (PAF). Laboratory testing has identified four main overburden types: limestone and non-acid forming (Green waste), PAF low capacity (Blue waste) and PAF high capacity (Red waste), and Heavy Sulfide Zone (HSZ), which contains greater than 20 per cent pyrite. Waste type block modelling indicates that at least 30 per cent of the overburden production from 2003 to the end of Grasberg pit operations will be limestone. Strategies are being developed to maximise the beneficial use of limestone through strategic blending and placement for ARD mitigation and control.

Jan 1, 2003

On 15 August 1998 the first section of the PUTRA LRT system was opened to the public as a free service prior to official commencement of revenue service on 1 September 1998. It is a remarkable achievement to open a highly advanced medium capacity urban railway scheme in four years after the outline concept began. Even more remarkable is the implementation of the next stage which is the underground section planned to be operational in mid-1999. The decision to build the first underground railway in any major urban centre is a technical challenge. The PUTRA LRT System can be likened to Hong Kong when the initial MTR system began in the 1970s and Singapore MRT in the 1980s. Prior to the PUTRA railway very little bored tunnelling had been undertaken in Kuala Lumpur. A few shallow sewer tunnels had been built but the main experience of tunnelling in Malaysia had been for water, hydroelectric and road tunnels usually through granite formations. The ground conditions in Kuala Lumpur were known mainly from experience of piled foundations and occasional deep excavations. The suitability and likely difficulties to be experienced during bored tunnelling could only be theoretically predicted. In both Hong Kong and Singapore, government owned corporations were set up to implement the scheme, but in Kuala Lumpur the whole project has been undertaken by a private company PUTRA, a wholly owned subsidiary of Renong Berhad.

Jan 1, 1999

By M Suzuki

Although several models for the surface tension of molten oxide slag have been proposed, suitably accurate predictions of this property are not yet possible. The surface tension, or surface excess free energy, of molten oxides is largely determined by the ionic coordination induced by surface relaxation. However, the associated mechanism of surface structural relaxation for molten oxide mixtures such as slag is complex and not yet fully understood. To allow a better evaluation of surface relaxation characteristics, the present work analysed the ionic coordination associated with the surface-relaxed states of several oxide mixtures. This work especially focused on calcium aluminate slags because these materials exhibit complex relationships between composition and surface tension. The effects of incorporating low concentrations of SiO2 as a surface active component on the surface ionic coordination were also examined. X-ray absorption techniques were used to assess oxygen and cationic elements in glassy samples after surface relaxation treatments, and molecular dynamics simulations based on a polarisable ion model of molten slag with vacuum/melt interfaces were also performed. The X-ray absorption techniques provided data related to electron yields (which are primarily associated with surface features) and fluorescence yields (which evaluate the bulk material). Thus, the ionic coordination characteristics of both regions were investigated. The results of molecular dynamics calculations allowed statistical analysis of the distributions of Al- or Sicentred polymorphs as well as the bond angles between cations and oxygen anions in the vacuumexposed and bulk regions in the equilibrated melt. The results indicated that bridging oxygen ions were preferentially distributed in the relaxed surface region rather than non-bridging oxygens. These bridging oxygen ions represented vertex connections between AlO4 or SiO4 tetrahedra. In the case of the calcium aluminate slags, the addition of one Ca2+ ion as charge compensation for two Al3+ ions was found to be necessary to form two AlO4 tetrahedra. This specific feature of surface ionic coordination could be responsible for the complex trends observed in surface tension data. The incorporation of low concentrations of SiO2 reduced the proportion of tetrahedrally-coordinated Al ions such that higher coordination states become dominant in the bulk of the material, whereas AlO4 tetrahedra were preferentially distributed in the surface region. SiO4 tetrahedra were the preferred Si-centred polymorph and were likely connected to one another to form bridging oxygen ions at the surface. On the basis of these results, a model to predict slag surface tension was proposed, and the energy of the formation of the ionic clusters resulting from surface relaxation was taken into account.

Aug 21, 2024

By T Gartner

This paper describes the design, manufacture and site services associated with the supply of mine hoists for the new mine under construction by Falconbridge Limited in Ontario, Canada. Two new shafts are being sunk, and the hoisting equipment at each shaft can be summarised as follows: Ventilation shaft:4.66 m diameter double-drum second-hand hoist, originally in operation at San Manuel Mine, Arizona, to be used as the shaft sinking hoist. The second-hand hoist presented a challenge in that during its previous life, the hoist had been intensively operated during service at San Manuel Mine, and this paper describes the scope of refurbishment work undertaken, both electrically and mechanically, to ensure future reliable operation, together with the requirement to meet Canadian and Ontario regulations and codes of practice. 3.05 m diameter new single drum auxiliary hoist to be used as a second means of egress. Main shaft:4.57 m diameter new double-drum hoist to be used initially as the shaft sinking hoist, and subsequently to be converted to the equivalent of a single-drum multi-rope hoist for service duties during the production phase; 5.49 m diameter new double-drum hoist to be used for skip hoisting during the production phase; and 3.05 m diameter new single drum auxiliary hoist.The new hoists are all designed to comply with SABS requirements such that hoisting with reduced rope safety factors will be possible in the future. This paper describes the principles involved both mechanically and electrically. Particular attention is paid to the conversion of the main shaft service hoist from a double-drum sinking hoist to a multi-rope hoist.This paper describes the ac electrical powertrains (drives and motors) used that eliminate the need for harmonic filters and reactive power compensation equipment since they exhibit no negative effects on the utility electrical network system. This paper describes the logistical challenges of installing, commissioning and setting to work a series of five hoists in a short time frame.

Jan 1, 2005

By R Valenta, J Owen, D Kemp, E Lebre, G Corder

Copper plays an essential role in our society. It is one of the key materials supporting economic growth and human development in emerging economies, for its common use in construction, power generation and transmission. It is also a critical metal for the transition to a low carbon future, particularly for its uses in renewable energy and electric vehicles. As a result, global demand for copper has been increasing steadily and is predicted to continue in the future. The demand-supply gap is currently growing, and new mines will be needed to fill it. This project observes the current pipeline of copper mining projects, which are characterised by technical complexity (lower grades, deeper deposits, complex mineralogy etc.) but also environmental, social and governance (ESG) complexities. A common assumption in the mining industry is that a rise in copper prices will unlock these deposits. However, while most technical complexities are price sensitive and are likely to be overcome in favourable economic conditions, the influence of ESG complexities is more difficult to evaluate. CITATION: Lebre, E, Valenta, R, Kemp, D, Owen, J and Corder, G, 2018. Accounting for social and environmental complexities in mining project developments: the case of copper, in Proceedings Complex Orebodies Conference 2018, pp 39–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By D Brown, K Markovic

The world is becoming an increasingly complex environment to operate within. Adoption and evolution of technology is occurring at a rapid pace and operating spaces are growing in interconnectedness and interdependency. In mining this is evidenced by the large-scale adoption of autonomous machinery, intelligent systems, Internet of Things (IoT) devices, and robotics to realise benefits in optimisation, productivity, and safety. To enable continual delivery and growth in operational performance, and to realise the aforementioned benefits, a new approach for managing mining and metals is required (Mining Review Africa, 2023). This means that an already talent constrained workforce must learn to manage the complexity inherent, evolving, and growing in the environment (Abenov et al, 2023). A key skill that needs to be further developed and deployed to combat these challenges and to enable robust problem solving is that of systems thinking, which is already practiced in pockets within the mining industry. Experience and learning can be leveraged from other industries and their application of systems thinking to ensure that focus is maintained on areas where the benefits from which will be optimised. With targeted application, a workforce capable of effective systems thinking can be the catalyst to optimisation across mining organisations.

Sep 1, 2024

By C Philander

The West Coast of South Africa is well known for its placer gem quality diamond deposits and also associated with these hosts of Cenozoic unconsolidated marine and aeolian sand and gravel are significant concentrations of heavy minerals. Exploration for economic concentrations of zircon, ilmenite and rutile along the coast started in the mid-1980s. This resulted in the discovery of an inferred 1.6 billion tonne resource with a grade of ten per cent total heavy minerals (THM), which developed into the Namakwa Sands Mine, a world-class producer of heavy minerals. Several other resources, including satellite deposits proximal and distal to the mine area, extensive diamond mine dumps and present day beach placers, demonstrate the vast heavy mineral potential along the West Coast. The favourable gangue to economic mineral ratio, a higher zircon content compared to other similar deposits, relatively lower U+TH content of zircon, low slimes content and effectively pristine low chromium-manganese ilmenite of these deposits, render them attractive exploration targets. Negative factors that will affect conventional mineral beneficiation and liberation include secondary mineral coatings and the regional coastal development of several layers of superimposed duricrust. The economically attractive heavy mineral assemblage along the West Coast is the result of erosion of the proximal, gneissic Namaqualand Metamorphic Province and mature Table Mountain Group sandstone, concentration by marine and aeolian processes and preservation under arid climatological conditions over a period of more than 100 Ma.

Jan 1, 2008

By Olson H, Kincaid R

The marine portion of the Pacific Basin and Rim constitutes a significant part of the world's surface in which the mineral resources are virtually undeveloped. Indications of substantial resources have resulted in speculation and uncertainty with regard to their potential in the near term. The main issues are centered on the markets for the resource materials, the technology needs for their recovery, and the possible impacts of their development on the environment. While the governments of Japan, France, the Soviet Union, India, China, and Korea are financing new programs in deep ocean mining, the US is consolidating its early leadership by the continuation of NOAA's authority under the Deep Seabed Hard Mineral Resources Act and the Sea Grant Act, Interior's authority under the outer Continental Shelf Lands Act, and by the development of a new Marine Minerals Technology Center within the Department of Interior's mineral institutes program, managed by the U.S. Bureau of Mines. The Center has a Continental Shelf Division (CSD) located in Mississippi, and an Oceans Basin Division (OBD) located in Hawaii. Research and training in the divisions is directed toward the practical aspects of mineral recovery from the nearshore and deep ocean environments with a strong bias for the OBD toward industrial and international cooperative programs in the Pacific Basin and Rim. In terms of resource development, the marine minerals in the Pacific Basin may be favored in some cases, in competition with land sources, by political and environmental considerations.

Jan 1, 1990

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

Getting it right is a very profitable outcome. Shareholders would ideally like to see their directors get it right all the time on the major economic decisions. But it is very difficult for mining directors to get it right all the time in such an uncertain environment. Primary decision-makers of companies with significant stakes in the mining industry should get it right much more frequently. The legal measures of evidence (beyond reasonable doubt and on the balance of probabilities) can be used to determine whether grade estimates (a key revenue variable) are realistic. The application of this approach can be far reaching. More frequently correct decision-making would result in more effective allocation of limited resources (capital and labour). In turn, this would result in higher financial returns and a more extensive mining industry.

Jan 1, 1994

By A Van Kersen, J Hodson

Waihi Gold Mining Co Ltd [WGM], operated by Normandy Mining, has been internationally recognised for its achievements in environmental management at the Martha Mine at Waihi. In a proactive approach to dealing with community concerns regarding blast vibrations on the North Wall cutback, trials were performed using the Cardox System [Cardox], to determine feasibility of achieving economic fragmentation of andesite overburden whilst bettering management levels of 5 mm/s peak particle velocity. Cardox is a non-explosive pressure breaking system which uses high pressure CO2, Results against conventional Ammonium Nitrate/Fuel Oil [ANFO] using a variety of delays showed that conventional blasting techniques could produce marginal fragmentation within the management levels with occasional excursions, whereas Cardox produced the required fragmentation while not registering on the vibration monitoring equipment. Fragmentation to enable normal excavation by a Hitachi EXII00 hydraulic excavator was achieved with a yield of 16m3 per round. The trails indicated that fragmentation with Cardox at the yields required of over 18m3 per round was possible with further product development. The trial demonstrated that non-explosive pressure breaking is feasible and its application warranted where environmental concerns affect the cost-benefit economics of production blasting in sensitive areas.

Jan 1, 2001

Constraints on the mineral industry are best treated as issues that have to be understood and managed in partnership rather than in conflict with communities. The Zapopan development at Mt Todd in Australia and the Martha Hill development at Waihi in New Zealand are but two of many recent successful examples at the local level. However, at the national level, the issues are more complex and more difficult to resolve because the most influential stakeholders are now the urban electorates and governments defer to their perceptions when making decisions and policy.

Jan 1, 1995

By M W. I Visser Æt Hooft, R C. Schimmel

Until recently the Corus IJmuiden pellet plant produced approximately 4.5 Mtpa of pellets. Corus IJmuiden is currently running a program to increase its pig iron production to 6.4 million tonnes HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50 per cent high basicity sinter and 50 per cent acid pellets, both produced in-house. To accommodate the increased pig iron production, the capacity of the pellet plant needed to be increased to 5.0 Mtpa. The productivity was increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

Jan 1, 2007

Mining and mineral processing makes a vital contribution to AustraliaÆs national export income, and our society today is critically dependent on its products. Despite the importance of this industry, its operations often come under scrutiny because of its high potential impact on local environments û both social and ecological. The challenge for the minerals industry today is to make the most responsible and best possible use of the national resource base, maximising overall resource utilisation.Research efforts and industry implementation of improvements have been moving in this direction for a considerable time already, and the industry has a long history of process innovation and improvement in Australia. Examples range from the early development of gold cyanidation and mineral flotation to more recent work undertaken under the auspices of AMIRA or through the various CRCs and research organisations such as the AJ Parker CRC for Hydrometallurgy, the Cooperative Research Centre for Mining Technology and Equipment and the Julius Kruttschnitt Mineral Research Centre.However, the nature of research and innovation in the mining and mineral processing sector is changing, as the industry itself copes with the pressures introduced by globalisation, industry consolidation and commodity price cycles. Large firms that have historically maintained a tradition of corporate technology and a culture of innovation are moving to outsource their technological and research competencies and are adopting æfast-followerÆ mentalities. At the same time, the challenges of sustainable development that need to be addressed are many-faceted, multidisciplinary, and require a holistic approach for significant achievements to be realised. Many sustainability issues, particularly those pertaining to environmental and safety issues, are shared across large sections of the minerals industry, and are seen as æindustryÆ problems beyond the scope of a single company.In this environment, collaborative research efforts are becoming the dominant mechanisms for building on past innovations and ensuring the continued success of the mining and mineral processing industries within a framework of sustainable development.

Jan 1, 2004

MANPOWER RESOURCES The optimisation of human effort has been an ongoing and significant process in the coal industry since industrialisation as we know it began. The extent to which the changes sought have been achieved has, over the years, been in the main determined by the economic and political forces existing at that time and the determination and character of the individuals involved. The question of optimisation is therefore not new in our industry. Hopefully this presentation will demonstrate to the reader the effect of previous measures adopted by industry to optimise all facets of its operation and in particular that of the human Resource.

Jan 1, 1991

By Lee M. F

The Lady Loretta lead-zinc-silver mineral isation of north-west Queensland was discovered first by Placer geologists in 1968 as a result of a geochemical soil survey. The stratigraphic position, mineralisation and rock associations of the deposit are very similar to those of the Mount Isa lead-zinc-silver orebodies. Aspects of the exploration history, geo- chemistry and structural geology of the Lady Loretta deposit, are discussed. A geometric model of the Ore Horizon is given.

Jan 1, 1974

By L Keeney

Cu-Au porphyry deposits are large tonnage low-grade resources dependent on processing large volumes of material. The ability to understand and predict comminution performance is critical, as it is frequently the rate-limiting step during processing. Parameters required from geometallurgical mapping and modelling of comminution performance are: A×b processing domains based on impact breakage variability, and BMWi processing domains showing grind response variability which lead to Mine throughput domains for a specific comminution circuit configuration. Due to the cost and/or large sample requirements of traditional comminution tests, insufficient data density and distribution of comminution indices commonly exist, making it difficult to model and map deposit scale variability. One method routinely applied to three dimensional domaining is to have an a priori zoning based on geological features (lithology, alteration, mineralogy, textures), and then apply to all material within a given domain the metallurgical values measured on a single sample or average of samples from that domain. The problem with this approach is that commonly the geological domains do not reflect comminution response, therefore compromising the quality of the average domain estimate. To resolve this problem an alternate integrated geometallurgical mapping and modelling method is applied to model and map comminution performance at Cadia East. This paper uses a data set of ~32 000 assay measurements and geological logging information, integrated with ~150 comminution measurements to analyse and develop proxy support models for comminution indices (ie A×b, BMWi, and throughput) based on inherent geological variability. Discrete downhole comminution processing domains are created, mapping orebody response while maintaining inherent variability.

Sep 5, 2011

By J Zhou, X Bi, Y Yan, W Peng, H Yang, D Weng, P Li

Fortescue Metals Group (FMG) fines from Western Australia is a hematite and limonite mix characterised by high crystal water content. Due to its higher supply capacity and lower prices, the Wuhan Iron and Steel Corporation (Group) intended to use more FMG fines in the sinter mix. It is understood that sinter quality is closely related to its microstructure featured by the hardness and brittleness of different mineral phases, the content of micro pores, and trans-cracks. In order to maintain sinter qualities such as tumble index, reducibility and so on at higher FMG fines blend ratios, a research project was initiated to study the effects of the FMG fines blending ratio on sinter microstructure. Research results showed that at higher FMG fines ratios, the hardness of hematite and magnetite were both decreased while the hardness of calcium ferrite showed a tendency to decrease. The number of cracks that were generated during Vickers hardness measurement in various mineral phases decreased, but their length was shortened, and the variation of crack lengths increased. The contents of hematite and magnetite were also reduced and the reduction of magnetite was clearer. Also the content of calcium ferrite and pores rose and the magnitude of the increase of pores was greater. Among all the mineral phases in sinter cakes, the Vickers hardness of hematite was highest within the range of 879 N/mm2 ~ 942 N/mm2, and therefore the decrease of its content in sinter and the enhancement of its brittleness, ie the number of cracks increased, were harmful to sinter strength. In addition, the excessive increase in pores content is also not favourable to sinter strength.CITATION:Bi, X, Yan, Y, Zhou, J, Peng, W, Li, P, Yang, H and Weng, D, 2013. Study of sinter microstructure with various blend ratios of Fortescue Metals Group fines, in Proceedings Iron Ore 2013 , pp 331-336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By McCarthy J

In both the U.S.A. and Canada regulations concerning the reporting on mineral resources and especially ore reserves have been established. The regulations are virtually identical for the two countries with the main exceptions being who is franchised to write the report and how the various reserve categories may be used in reports to the public. Both countries divide ore reserves into "proven", "probable" and "inferred" categories. "Proven" reserves are those for material for which tonnage is computed from dimensions revealed in outcrops, trenches, underground workings or drill holes and for which the grade is composed from the results of adequate sampling. "Probable" reserves are those which are less well defined than "proven" while "inferred" reserves are generally those which may exist through geological and geophysical interpretation. The AusIMM/AMIC draft guidelines as proposed for use in Australia define more rigidly the ore reserve categories into "proved" and "probable" terms, which can only be applied following a full and favourable analysis of economic, mining, metallurgical, marketing and sociopolitical factors. If the ore reserves are not supported by this analysis they are placed into a "resource" category. Proper application of this proposed Australian model could prove useful when dealing with grass-root prospects or mining properties in the pre-feasibility stage. Combined with competent reporting, use of the proposed guidelines should ensure standardised and more verifiable analysis/valuation of a company's mineral assets.

Jan 1, 1987