Search Documents

By G. W. Thomas

Jan 1, 1967

By Victor L. Stevens

The Oso tunnel is one of three tunnels located on the San Juan-Chama Project in south-central Colorado. The purpose of the tunnel is to carry water from the upper San Juan watershed through the Continental Divide into the Rio Grande watershed. The Oso tunnel contract was awarded by the U.S. Bureau of Reclamation to a joint venture of Boyles Brothers Drilling Co., Gibbons & Reed Co., and Cimco in February 1966. The Oso tunnel is 26,660 ft long and has a rock section of 10 ft, 2 in. with a lined diameter of 8 ft circular. The main portion of the rock formation was in the Lewis shale. This formation is quite consistent in hardness and texture with exception of localized limestone concretions and sandy siltstone inclusions. The job was bid on the basis of using a James S. Robbins mole of the P221 series. The decision for using a mole was predicated on the geology and the experience of the same joint venture on the adjoining Azotea tunnel where a mole was successfully used. The Robbins P221 series mole is capable of cutting from 9 ft, 11 in. to a 10 ft, 7 in. diam without any major change. It is 40 ft long and weighs 60 tons. The cutting head has 22 disk-type cutters and one center pilot (standard 9 7/8 -in.) tricone bit. The head is powered by four 75 hp electric motors. Gripper pads at about the midway point on each side of the machine are pushed into the tunnel ribs and thrust-cylinders in front of each gripper apply pressure to the face as the head rotates. The regripping cycle is 3 ft and then the grippers are retracted and advanced. Each cutter on the perimeter of the head is followed by a bucket which scoops up the cut material, almost in the same manner as a water wheel, and dumps it into a conveyor situated along the top of the mole. The muck from the mole conveyor is dumped into a gantry-type conveyor. The gantry conveyor is 350 ft long and is pulled

Jan 1, 1970

Discussion of "The Ordering Transformation in Titanium-Aluminum Alloys Containing up to 25 at. pct Aluminum" by F. A. Crossley, Trans, TMS-AIME, 1968, vol. 242, pp. 726-30. Dr. Blackburn, in his response, pointed out that the c/a ratio of the Ti-26 at. pct A1 alloy quenched from 900°C is 1.6006 and not 1.5965 as plotted in Fig. 19. An error in transcription was made in preparing Table V of Ref. 1 (F. A. Crossley, Trans. TMS-AIME, 1966, vol. 236, p. 1174). The corrected Fig. 19 strengthens rather than weakens the argument that a martensitic transformation occurs in alloys containing from 15 to 18 at. pct Al. A Study of the Factors Which Influence the Rate Minimum Phenomenon During Magnetite Reduction, by P. K. Strangway and H. U. Ross, Trans. TMS-AIME, 1968, vol. 242, pp. 1981-88. Page 1883 Reverse Figs. 5 and 6. Sigma—Its Occurrence, Effect, and Control in Nickel-Base Superalloys, by J. R. Mihalisin, C. G. Bieber, and R. T. Grant, Trans. TMS-AIME, 1968, vol. 242, pp. 2399-2414. Pages 2403, 2407, and 2414 Arrows should appear on Figs. 4 and 9; a sigma is missing from Table IV; line 2, page 2414, change "case" to "cast". These are published correctly in the bound volume. Index, December Issue There were a few omissions in the Author Index. These have been corrected and published properly in the bound volume.

Jan 1, 1970

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

By E. M. Wise

THOUGH known as the platinum-group metal- the sextuplet, platinum, palladium, iridium. rhodium, osmium, ruthenium, might well be called the American metals or perhaps Pan-American metals, as the ore containing them eras first discovered in South America, and in recent years the largest production has come from North America. The South American alluvial deposits, which also, contain gold, are in active production, as are the alluvial platinum deposits of Alaska, but the main production is from the copper-nickel ores of Sudbury, Ontario. The Russian deposits in the Urals were the source of most of the worlds platinum for about 100 years, but since 1934 have assumed second place. For a time considerable amounts of platinum came from several rather rich deposits in South Africa but these were exhausted quickly. However, a tremendous reserve of lower-grade ore exists there, which could be worked profitably if the price of platinum were considerably higher.

Jan 1, 1942

By HENRT M. HOWE

IN my original paper, Piping and Segregation in Steel Ingots, I pointed out1 among other things that, in view of the slighter stretching (virtual expansion) of the crust, and greater opportunity for sagging, there should be less piping in broad than in narrow ingots, and less in slowly-cooled ingots, e.g., those cast in pre-heated sand molds, than in those which cool quickly, e.g., those cast in iron molds. A. A. Stevenson2 said that neither of these predictions agreed with his own experience. In particular, in a picture which he showed of a wide and of a narrow ingot cast from the same ladleful of steel,, the wide ingot had certainly piped much more deeply than the narrow one. At the time I did not see the explanation of these discrepancies, but further reflection makes it evident. One of the most important elements in determining the depth of the pipe is the degree of " top-lag," that is, the degree to which the solidification of the top of the ingot lags behind that of the bottom. 'Through this lagging the steel of the upper part of the ingot is able to run down and fill the pipe below as fast as it forms. To the importance of this lagging I called attention in my original paper.' Sand vs. Iron Molds.-If we compare two like ingots, one cast in an iron and the other in a sand mold, we see that the top-lag' is much greater in the former than in the latter, be¬cause in the former the lower part of the ingot is cooling off fast while the metal is running into the upper part. It is perhaps easier to look at this as a case of the solidification of the hot-

Dec 1, 1909

By H. Stuart, L. Zwell, N. Ridley

specimen that was subjected to 700°C for 250 hr is shown in Fig. 2(c). The precipitates in this foil appear round and exhibit only very faint strain contrast. From this evidence, along with that described above for the symmetry of the strain field, it may be concluded that this coherent precipitate is spherical, which is generally the favored shape for coherent precipitates when the lattice parameter mismatch is small.12 These observations are consistent with the assumption that this precipitate is the y' (Ni3Al, Ti) phase. y' is known to be spherical in the early stages of precipitation. It is fcc and is similar in composition to the matrix and thus would have contrast similar to that of the matrix as do these precipitates. Direct identification of the spherical precipitate did not prove possible because of its low volume fraction and small size. The results of this investigation suggest that the increases in yield strength and the decreases in elongation observed in 45-Fe 30-Ni 20-Cr alloys containing about 0.4 pct A1 and 0.4 pct Ti on prolonged aging at 550" to 700°C are very likely due to the presence of a coherent, spherical precipitate, thought to be y'. Mi-crohardness measurements indicated that the precipitation of semicoherent M23C6 resulted in some matrix hardening. However, this precipitation process occurs much more rapidly than the changes in mechanical properties at these temperatures. 1C. L. Clark, J. J. B. Rutherford, A. B. Wilder, and M. A. Cordovi: J. Eng. Power, 1962, vol. 84, p. 258. 2 F. A. Comprelli and U. E. Wolff: USAEC Report GEAP-4745, General Electric Company November, 1964. 3C. N. Spalaris: A Monograph, USAEC Report GEAP-4633, General Electric Company, July, 1964. THERE have been many X-ray investigations of the room temperature lattice parameters of austenite which has been retained in quenched steels of various carbon contents. The results of these investigations have been collected by Wrazej,1 Wever et al.,2 and by Roberts3 and are included in Fig. 1 due to Pearson.4 The dashed line in Fig. 1 was considered by Roberts3 to most reliably describe the variation with carbon content of the lattice parameter of retained austenite. This line is given by the equation: a (Å) = 3.555 + 0.044 wt % C and recent unpublished measurements by one of the authors (LZ) support this relationship. The object of this communication is to draw attention to a relationship which describes the variation of the room temperature lattice parameter of 'equilibrium' austenite with carbon content, and which is different from that for retained austenite. The relationship a(Å) = 3.573 + 0.033 wt % C has been obtained from lattice parameter measurements made on equilibrium Fe-C austenites at elevated temperatures, which have been extrapolated to room temperature. The room temperature lattice parameter of 3.555Å which the Roberts' relationship gives for pure y-Fe is no: in agreement with the value of 3.573Å obtained when the high temperature lattice parameter data of Basinski et aL.5 and of Goldschmidt6 is extrapolated to room temperature. A linear extrapolation was

Jan 1, 1970

By D. K. Crampton

ON giving thought to the subject of this paper, my first reaction was that many and striking changes have come about as a direct result of the war. However, more careful analysis indicates that few, if any, of these changes can be wholly attributed to it. The actual situation is that all these changes were conceived and most of them at least partially executed in re- cent prewar years, it remaining the role of war to achieve results in a fraction of the time that might normally have been taken, lacking its driving impulse. The further discussion will therefore be with the premise that the individual changes have been greatly hastened rather than directly and primarily caused by any war conditions. Co-operation among copper alloy producers on production problems is agreed to be much worth while. The industry was too long noted for jealousy and secrecy as to equipment, methods, and even materials produced. Gradually, a more open and co-operative policy evolved but even just prior to the war the interchange of ideas was relatively cautious and limited. The need for a great increase in production in record time fostered a more co- operative attitude; exchange of ideas and experience concerning all phases of production increased tremendously to the benefit of the individual participants and thus the war effort, too. This more united effort has undoubtedly led to many specific improvements in process or equipment and these in turn to more rapid and economical operation than could have taken place on an each-for-himself basis.

Jan 1, 1944

By H. B. Pulsifer

ONE of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition.

Jan 1, 1931

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10 to Aug. 10, 1915: Members ALBERTSON, MAURICE MERTON, Mine Surveyor, Mining Corporation of Canada, Cobalt, Ont., Canada. ARMSTRONG, GEORGE CHANDLER Mgr., Indian Refining Co., Lawrenceville, Ill. BARBER, MAX HAYDEN, Min. Engr Supt., Crosby Mine, Nashwauk, Minn. BARNESON, JOHN Merchant, 310 Sansome St., San Francisco, Cal. BENSEL, JOHN A., Cons. Engr 111 Broadway, New York, N. Y . BORGESON, ANSHELM CYRUS, fin. Engr Shenango Mule, Chisholm, Minn. BROOKS, CHARLES PETER, Min. Engr 228 Dooly Bldg., Salt, Lake City, Utah. BROWN, FRANK HAROLD, U'011',. Min. Engr., Federal Co., Inc., 50 Broad St., New York, N. Y. CLARK, DOUGLAS Kellogg, Idaho.

Jan 9, 1915

By D. A. Dukelow, K. Li, G. C. Smith

Decarburization in the Fe-C system by oxygen top blowing has been studied in laboratory -scale experiments. It is shown that equilibrium models fail to explain or predict either the course of refining or endpoint conditions, giving results which either are incompatible with the chemistry of the system or do not satisfy material balance requirements. Also the path of decarburization was found to vary even for heats made under apparently identica1 conditions. A promising approach to analyzing the decarburization results is to relate oxygen efficiency fm carbon removal to bath carbon content. This relationship for Fe-C heats shows the same range of oxygen efficiencies as is obtained in pilot-plant and commercial heats using hot metal-scrap charges. This implies that oxygen transfer is primarily controlled by the decarburization reaction itself, independent of other refining reactions. Therefore, it should be possible to study separately decarburization and slag-metal reactions. DECARBURIZATION is probably the most important reaction in steelmaking. Not only is it a main reaction in the refining of iron to steel but it also provides the stirring action in the bath necessary for the diffusion processes to proceed at reasonable rates so as to make a steelmaking process practical. Kinetics of decarburization in the open-hearth process has been a subject of investigation for many years.&apos;-B It is generally accepted that at steelmaking temperatures the rate of homogeneous C-0 reaction is extremely high and cannot constitute a rate-controlling step. Diffusion of oxygen through a boundary film in the metal phase has been suggested by arken&apos; as rate-determining. Recently, Larsen and sordah16 concluded from experiments in a laboratory furnace that, with oxygen supplied from air or combustion gases, the rate of "steady-state" carbon boil is controlled essentially by a diffusion process of O2, Co2, or H2O through a film of nitrogen above the slag surface. Displacing this diffusion film by a stream of nearly pure oxygen produced a ten-fold increase in the rate of carbon boil with the rates of slag-metal oxygen transfer, bubble nucle-ation, and other steps all apparently able to keep pace. In the top-blown basic oxygen process, however, the transport of oxygen takes a more direct route. and the state of bath agitation is much more turbulent than in the open-hearth process. In addition, direct contact of the gas with the metal phase provides opportunity for direct oxidation of carbon. It is likely that the rate-limiting factor for the decarburization reaction will be different. However, only a few descriptive discussions of the subject have been reported in the literature.10-l2 Studies of the decarburization kinetics based on plant or pilot-plant data are necessarily complicated and are influenced by other refining reactions which occur simultaneously. In order to investigate the mechanism of decarburization, experiments have been conducted in which carbon-saturated iron melts were top-blown with pure oxygen over a range of conditions. It is hoped that this study will form a foundation on which a more basic understanding of this important reaction may be built. EXPERIMENTS One group of blowing experiments was made in a standard 200-lb induction furnace and another group in a 500-lb induction furnace. The furnaces were modified to the general shape of a basic oxygen furnace by adding a rammed refractory cone section to the regular crucible body. Crucible and cone were of high MgO (95 pct) material. A water-cooled lance, 1/2 in. in diam and threaded at one end to take a nozzle, was used for blowing oxygen. The lance with its water and oxygen lines was supported on a cantilever arrangement so that it could be moved up, down, or sideways. Oxygen of 99.5 pct purity was supplied from a cylinder and metered through a rotameter equipped with pressure and temperature gages. Another pressure gage was located at the top of the lance. A schematic diagram of the assembly is shown in Fig. 1. Before each experiment, a weighed amount of ingot iron, containing 0.02 pct C, < 0.01 pct Si, 0.10 pct Mn, 0.019 pct P, and 0.015 pct S, was charged in the furnace and melted down by induction heating. Graphite was then added to the molten charge until it became saturated. When the temperature of the charge reached the desired level, the lance was lowered to a predetermined height above the bath

Jan 1, 1964

By E. H. Jr. Dix

A LACK of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys .and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investiga-tion an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100° C. are too small to be of practical importance.

Jan 1, 1935

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster&apos;s New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on &apos;account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several&apos; months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man&apos;s&apos; solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By Herbert J. French

ALLOY steels have become essential to industry in meeting the rigid requirements on materials imposed by our, advanced technology. In comparison with the total ingot capacity of the steel industry, the volume of alloy steels is relatively small although for many years annual alloy-ingot tonnage has, been in seven figures. However, the monetary value of the alloy-steel production is exceedingly high and the benefits derived from the products are relatively great. The trend in total ingot production since 1932 has been generally upward with only two major interruptions. That of the year 1938 was due to a decrease in general business activity whereas that of 1946 resulted largely from work stoppages. Traditionally, the tonnage of alloy-steel ingots produced was in the neighborhood of 5 to

Jan 1, 1948

By A. A. Stripling

The Cretaceous limestone wells of the Mara/Maru-caibo Dist. of Venezuela are extremely prolific producers. To maintain production on cessation of natural flow, large scale gas-lift operations were commenced involving high production rates on caring Flow. For the design of these gas-lift installations it was essential to have some knowledge of the pressure gradients involved in casing flow, so that the required injection pressures, optimum gas injection raws, etc., could be forecast. This paper presents a method of calculating these annular pressure gradients. Basically the method makes use of an energy balance equation coupled with an empirical energy loss factor derived from field data. The calculations have been put in a form suitable for "punch card-type" calculating machines. A set of gradient curves for Mara/Maracaibo conditions covering flow rates up to 12,000 B/D, and GOR&apos;s of 500 to 2,000 cu fd/bbl is presented. From these curves the flowing BHP can be predicted from surface data and the vertical pow performance under varying conditions of gas injection can be estimated. The method has been applied to La Paz and Mam gas-lift operations for over three years and has given consistently accurate results. INTRODUCTION The Cretaceous limestone fields of the Mara/Maracaibo area in Venezuela are characterized by the presence of widely distributed fissure systems. Under these conditions individual wells frequently have extremely high potentials and such wells are generally flowed on the casing-tubing annulus in order to reduce the pressure loss in vertical flow. To maintain production on cessation of natural flow, an extensive gas-lift system was planned. As a first approach to this gas-lift design problem, an attempt was made to construct a set of empirical flowing gradient curves from the available subsurface pressure data. Such a method has been used successfully for tubing-flow conditions in California by Gilbert&apos;. Unfortunately, the empirical construction of casing-flow gradient curves presents additional difficulties, as pres- sure bombs cannot bc run in the casing-tubing annulus against high rates of flow. Thus, the Full flowing gradients cannot be defined by actual measurement and the best that can be done is to obtain spot pressures at the tubing shoe. Under these conditions a vast accumulation of BHP data is required to construct a set of gradients. To the La Paz and Mara fields the majority of the available flowing pressure measurements fall into a relatively narrow GOR range, in the neighborhood of the solution ratio. While there appeared to be reasonable prospects of constructing gradient curves for this limited range, measurements at higher GOR&apos;s, which were of major interest for gas-lift operations, were relatively few and the prospects of constructing empirical curves cor~spondingly remote. As an alternative approach, the possibilities of a mathematical analysis of vertical flow conditions were investigated. May and Laird2fV n 1934 presented an excellent analysis of the vertical-flow conditions in the Anglo-Iranian Oil Co.&apos;s fields. Their analysis was based on an energy-balance equation and calculated the losses due to kinetic energy, friction and slippage separately. By combining these losses with the total calculated available energy, the required depth-pressure traverse could be deduced. On applying the method to La Paz conditions, good results were obtained for tubing flow at high tubing-head pressures. However, for lower wellhead pressures (300 psi and under) the discrepancy between calculated and measured values increased appreciably. It was considered that this was probably due to energy losses caused by slippage or liquid hang-up in a continuous gas phase, for which it was difficult to visualize any analytical approach. In 1952 Poettmann and Carpenter4 presented a method of pressure gradient calculation which, while based on an energy-balance equation similar to that employed by May and Laird, made no attempt to evaluate the various components making up the total energy loss resulting from irreversibilities of flowing fluids. Instead, they proposed a method of analysis which assumed that all significant losses for multiphase flow could be correlated in a form similar to that of the Fanning equation for frictional losses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The total available

By AIME AIME

The Washoe plant, 1 in Anaconcla. Mont., together with the local street-railroad, ranches a. foundry and machine-shop a brick-plant and the Montana hotel, form a property under one management; to which should be added the mines in Butte owned by the company, from which part of the ore-supply of the plant comes. The Anaconda Copper Mining Co., controlled by the Amalgamated Copper Co., was reorganized under the laws of Montana in 1893. A map of the plant, showing the numerous departments and illustrating the details of tracks, pipe-lines, and charging-stations for compressed-air locomotives, is given in Fig. 1.

Jul 1, 1906

President-Mrs Robert D Coombs, 375 Paramus Road, Paramus, N J First Vice-President-Mrs Howard R Norsworthy, 333 East 53 Street, New York 22, N Y Second Vice-President-Mrs Arthur Notman, Circle Road, Dongan Hills, Staten Island 4, New York Third Viee-President-Mrs David Eugene Park, 30 Sutton Place, New York 22, N Y Fourth Vice-President-Mrs Cony T Brown, 211 East Abeyta Avenue, Socorro, New Mexico Fifth Viee-President-Mrs J A Carpenter, 245 University Terrace, Reno, Nevada Recording Secretary-Mrs W McG Peirce, 7 Lexington Avenue, New York 10, N Y Asst Recording Secretary-Mrs Arnold H Miller, 601 West 115 Street, New York 25, New York Corresponding Secretary-Mrs Theodore Nagel, 76 Remsen Street, Brooklyn 1, New York Treasurer-Mrs Robert W Rowen, 116 East 68 Street, New York 21, N Y Assistant Treasurer-Mrs Samuel H Dolbear, 11 Broadway, New York 4, N Y Assistant Treasurer-Mrs H A Kursell, 12 Murray Hill Road, Scarsdale, New York

Jan 1, 1955

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.&apos;s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952