Search Documents

By Peter N. Calder, G. H. Blackwell

The development of an open pit slope monitoring system, from equipment selection and justification to complete computer data storage and analysts, Is described. Methods of overcoming the Limitations of the electronic transit/distance measuring device and survey system selected are discussed. Results of the monitoring program showed that blasting was a major cause of Instability, and, after much experimentation, suitable blast patterns for mine production and pit wall integrity were designed. The experiences gained with double benching 'and wall cleanup procedures are discussed . The monitoring program also indicated that water was a contributor to instability, and methods of dealing with water In a rock with a low storage coefficient and transmissibility are described. Because of the danger of falling rock, photogrammetric methods are used for joint mapping and analysis, this work being contracted out. Joint strengths are measured on-site using a portable shear tester. Finally, a discussion of a complex failure is given.

Jan 1, 1983

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By C. H. Mathewson, Kent R. Van Horn

Copper and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.' It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

By J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;1-8 in labor periodicals, 10 11 in popular journals and periodicals,12 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council, 9, 14-15 the American Mining Congress, 1, 16 the American Institute of Mining and Metallurgical Engineers, 2, 4 the Mine Inspectors' Institute of America,6,8,17,18 the Coal Mining Institute of America, 5, 19, the American Standards Association, and others.20,21

Jan 1, 1949

By W. B. Wise, H. D. Attra, W. M. Black

The purpose of this paper is to illustrate a comparatively new approach for solving a problem that has plagued oil producers for many years—how to make the most money with available field production capacity. In a very basic operation such as a top-allowable one-well field, a computer and staff of engineers are not required to determine that the best operation is to produce that well at its maximum for as long a time as it will produce. However, as the problem becomes more complex and the number of wells and number of reservoirs increase, it probably will be a wise choice to devote some engineering thought and calculation time to determine the best way to operate that field on both an ultimate and day-to-day basis. Continued developments in the field broadly referred to as "operations research" have led to a number of useful engineering analyses for optimizing field operational problems. One of these techniques, termed linear programing, is parlicularly interesting because of its potential applications to the study of complex oilfield operating problems. Linear programing is concerned with the problem of planning a complex set of interde~endenl activities in the best possible (optimal) fashion. A field application of linear programing is being used to maximize daily income from a multi-reservoir producing operation. The initial results of this study indicate that the linear programing technique (I) can be applied effectively to field problems, (2) can be used to detect unsuspected avenues for improving operations and (3) can effect a significantly improved means of controlling field operations through the use of the highspeed computer. INTRODUCTION The usual approach for studying complex field operational problems has been to look in detail at several basic plans suggested by judgement and experience and, then, to choose the best plan from those investigated. This approach is entirely satisfactory provided: (1) that judgment and experience alone will reliably pick the best or near the best program as one of the plans to be investigated; and (2), and most important, that the factors which control field production will not change. This paper deals with the large group of field operations which are at least one-step removed from a satisfactory solution using the conventional method of analysis. Problems such as pipeline- and gathering-system design, transportation studies, large field development projects and multi-reservoir producing operations fall in this latter category. To find the best program for handling these problems when the best program is not obvious, a complete optimization study is required, and high-speed computers are required to continually update the program once it is selected. Operations of this type have an extremely large number of possible solutions. However, only one will result in maximum economic return and, more important, this one program must be re-evaluated and adjusted constantly to accomodate such changing field factors as the number of producing days, the price of crude, the discovery of new reserves, declining reservoir pressure with subsequent decline in production and a host of other factors which characterize specific operations. One of the most widely used, direct methods of optimization is a numerical procedure termed "linear programing", which is designed to investigate systematically each of the possible solutions involved in a given problem, determining rapidly and uniquely the optimum answer. As implied by the name, linear programing requires that all field variables be either defined or expressed in a series of interdependent linear equalities or inequalities. These relationships are solved simultaneously, using a form of matrix solutions to determine the optimum values for each producing variable that will maximize net profits. The solution techniques used in a recent field case study is termed the "simplex method" and is discussed in full detail in Ref. 1.

By C. W. Hall

MINE executives, as a rule, have always been willing to adopt new ideas of operation, or to listen to proposals which might increase the effectiveness of their enterprise, more especially so if they could be shown how definite results might be attained by introducing any conception suggested. In these days of high wages, high cost of supplies, and high taxes, operators are even more inclined to accord consideration to innovations or improvements, and many go so far as to employ men to conduct special investigations and make studies for the purpose of advancing production. Where a man is brought into an organization to do work of an efficiency nature, it often creates resentment among the operative heads because of having their work directly scrutinized, or investigated, and there is a tendency, if not actually to obstruct, to fa.il to cooperate; in which case the investigator is handi-

Jan 1, 1925

By M. W. Lightner

IN 1947 the steel industry rebounded from its wartime effort and produced a record-breaking peacetime tonnage of steel ingots. During the first six months of the year the industry produced 42,000,000 tons of ingots and expected to produce 85,000,000 tons for the year. With a rated capacity of some 91,000,000 tons, production was at a rate of about 93 per cent of capacity. Credit must be extended to the steel producers who have maintained this steady state of operations while faced with many problems, not the least of which was a continued shortage of satisfactory scrap. Furthermore, the steel industry started a record-breaking peacetime expansion program at a total cost of more than $1,000,000,000. This program will increase the ingot-making capacity of the country by 2,500,000 tons and should be completed in 1948.

Jan 1, 1948

By E. Martinez, M. L. Hollander

Sulfurization of copper oxides was investigated using differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). When mixtures of cuprous oxide and sulfur were heated, the surface of the cuprous oxide was converted to cupric sulfide at the melting point of sulfur (119°C); additional sulfuriza-tion took place when the sulfur vaporized above 200°C. Cupric oxide also reacted with sulfur to form cupric sulfide but the starting temperature was approximtely 225°C. When the cupric oxide and sulfur were physically separated, sulfurization still occurred indicating a reaction with the vapor phase of sulfur. Sulfurization was obtained in runs with cuprite, chrysocolla and basic copper carbonate. Further decomposition of cupric to cuprous sulfide was noted at somewhat higher temperatures. The DTA-TGA data made it possible to set up postulated reactions in each system. These techniques were found to be well suited for studies of this type. Because of the difficulty encountered in flotation of many metallic oxide minerals, efforts have been made to find suitable reagent combinations to sulfi-dize these minerals in the flotation circuit. Recently Bautista and Sollenberger,1 using a different approach, showed that the surfaces of many oxide minerals can be converted to sulfides by heating them with sulfur to temperatures between 150° and 225°C. This technique was effective even with chrysocolla, a mineral which is very difficult to sulfidize. The primary objective of the present study was to obtain information on the reactions between the oxide minerals and suIfur. A better understanding of the mechanisms involved might prove useful in pointing the way to improvements in the process. A secondary objective was to demonstrate the value of thermo-analysis in investigations of this type. Bollin and Kerr2 have reported the use of a modification of differential thermal analysis to study the thermal reactions which occur on heating elemental constituents in a closed system to synthesize copper sulfides and iron sulfides. Differential thermal analysis (DTA) was used to detect enthalpic changes as mixtures of minerals and sulfur were heated. The DTA indicated the temperatures at which reactions started and whether they were exothermic or endothermic. Weight change data were obtained by thermal gravimetric analysis (TGA). These data could often be used to support postulated reactions and to eliminate consideration of other possible reactions. EQUlPMENT Differential thermal analysis (DTA) involves measuring the temperature difference between the sample being tested and a thermally inert reference, generally aluminum oxide, as both are heated at a uniform rate. Series connected thermocouples in the sample and reference are used to detect the temperature differences that occur as the sample undergoes enthalpic changes.3 Crystalline transitions, fusions, vaporizations, dehydrations, decompositions and many solid state reactions can be detected. A DTA unit manufactured by the Robert L. Stone Co., Austin, Tex., was used in this investigation with a temperature rate increase of 10°C per min. The samples and reference were placed in Inconel cups with wells in the bottom into which the differential thermocouples fit, and run in a nitrogen atmosphere. Thermal gravimetric analysis (TGA) measures the changes in weight that a sample undergoes as it is heated. A Chevenard thermobalance converted electronically for graphic recording was used with a heating rate of 5°C per minute. An X-Y recorder plotted temperature on the X axis and weight changes on the Y axis. A flow of 250 ml per min of nitrogen was streamed through the furnace. Samples were placed in a porcelain crucible open at the top, unless otherwise noted. EXPERIMENTAL RESULTS Sulfur: Two sulfur samples from different sources were tested. The DTA of a high purity sulfur and a reagent grade sublimed sulfur are shown in Fig. 1. Nearly all the tests were run with the sublimed sulfur due to the difficulty in grinding and high electrostatic charge encountered with the high purity sample. Sulfur undergoes three endothermal reactions below 200°C. The first is a solid-solid crystalline transi-

Jan 1, 1964

By Floyd C. Kelley

The literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough invest,igation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibtiuni produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizingl which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. Diffusion of Metals in Iron It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By George Sachs, S. M. Clark, George Espey

he tendency of a commercially drawn cartridge case to crack in the mercury test and the relation of cracking tendency to residual stress retained after drawing were studied. The fourth drawpiece (next to the final) of caliber 0.30 cartridge cases produced by Frankford Arsenal were selected as test pieces. These exhibited an exceptionally high cracking tendency, making a detailed study possible. To obtain fast cracking in the mercury test, about 0.0015 to 0.003 in. must be removed from the wall thickness of the drawpiece by pickling, and it must be subjected to the mercury test immediately after washing. Removal of the adhering mercury by annealing and subsequent squeezing of the case in a vise was used to reveal definitely the presence or absence of cracks. Various lots of apparently identically fabricated cases were shown to possess a different cracking tendency. Machining off or boring a hole in the base gradually reduced and eventually eliminated the cracking tendency. On the contrary, shortening of the wall (body) reduced the cracking tendency only if the wall became so short that the cracking zone was directly affected. By boring out the base and pickling from the outside and then splitting the resulting rings, it was possible to determine the approximate stress distribution in the base and in the adjacent part of the wall. Small compression stresses were present in the core and the major part of the base, while the surface of the base and the adjacent wall contained high circumferential tensile stresses. On the contrary, the wall when parted from the base contained only insignificant residual stress. The conception is advanced, that the stress distribution in a drawn cartridge case corresponds fundamentally to that of a tube (wall) shrunk on a disk (base). Such a stress distribution results from the tendency of the base to recover elastically by an increase in diameter from the biaxial compression during drawing while the wall exhibits little tendency to change its diameter after progressing through the die. This is confirmed by measurements which show the base diameter to be slightly larger than the wall diameter.

Jan 1, 1945

1913. FRANK DAWSON ADAMS Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacristan, Durham, England. 1923. GELASIO CAETANI Rome, Italy. 1920. HENRY STURQIS DRINKER Merion Station, Pa. 1922 FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England 1928. JOHN HAYS HAMMOND. .New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Park, France. 1931. WALDEMAR LINDQREN Cambridge, Mass 1929. JOHN MARKLE. .New York, N. Y. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1909. ALEXANDRE POURCEL Park, France. 1911. ROBERT H. RICHARDS Cambridge, Mass.

Jan 1, 1932

1913. FRANK DAWBON ADAMS Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriaton, Durham. England. 1923. GELAEIIO CAETANI Rome, Italy 1920. HENRY STURQIB DRINKER Merion Station, Pa, 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYB HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1931. WALDEMAR LINDQREN Cambridge, Mass. 1929. JOHN MARKLE New York, N. Y. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1909. ALEXANDRE POURCEL Paris, France. 1911. ROBERT H. RICHARDS Cambridge, Mass.

Jan 1, 1932

By J. G. Bouwkamp

This paper presents three general approaches towards the solution of the stress distribution and the behavior of tubular connections as used in offshore well drilling structures. First, the possibilities of using plastic models and photoelasticity techniques in evaluating the stress distribution in gusset plate connections are analyzed. The results of photoelastic studies on the stress distribution in the in-plane gusset plate of two-dimensional joints are presented. The influence of the configuration of the gusset plate (with and without cut-outs) is discussed. Second, the paper deals with recent developments and applications of computer programs to analyze connections with directly inter-welded tubes and with gusset plates. The possibilities and limitations of these programs are discussed. Stress patterns analyzed with these programs are presented for different joint configurations. Finally, the basic test procedures and results of a test on a tubular joint under static and alternating loads are discussed. INTRODUCTION The effective design of tubular connections as encountered in offshore well drilling towers or floating platforms has been complicated basically by the radial flexibility of the tube walls. This flexibility is a source of severe stress concentrations which can initiate an early failure of these joints. In an attempt to reduce the influence of the wall flexibility of the column tube, certain joints are presently designed by inter-welding the incoming branch members. In those designs, the force acting normal to the chord tube can be reduced considerably. A second group of joints incorporate gusset plates or stiffening rings to stiffen the column wall and to distribute the incoming branch member forces over a larger part of this wall. A third approach to improve the stress distribution in a tubular joint is to increase the wall thickness of the column member. This can be achieved by simply applying a thicker wall section in the vicinity of the joint. A fourth possibility to restrain the radial flexibility of the tube wall is to fill the column member with concrete. Also, a single, cast steel seat welded to the column tube can be used to improve the stress distribution in this wall. Although all these designs improve, in general, the state of stress in the column wall, the altered stiffness often causes the development of critically stressed areas in the web members. At the same time the actual design in most instances is decisively influenced by the site which governs the depth and controls the forces produced by waves, earthquakes and ice flow. Also, the towing, erection and foundation requirements of offshore structures can affect the actual design selection. Because of the complexity of the structural configuration of tubular joints, the stress analysis of these connections has necessarily been based on simplified and often crude assumptions. For the earlier and smaller type of connections with about 4-ft diameter column sections, the primary problem was to evaluate the relative stiffness of the column wall section and the load transfer between joint members. Due to the recent developments of offshore drilling structures with increasingly larger connections (e.g., column diameter. 32 ft; web members, 8.5 ft) this problem has become even more critical. One design philosophy for such large joints follows a member-to-member connection with radially heavy reinforced column sections. This radial stiffness can be attained by closely spaced and intensively stiffened horizontal diaphrams together with vertical stiffeners. A second solution incorporates a concrete-filled section between the outer and inner walls of the column tube. Another philosophy considers large gusset-plated joints. The problem in these joints is to develop an effective load transfer between the branch tubes and the gusset plate and to minimize the stress concentrations in the member walls as effectively as possible. Several concepts are followed to achieve this gradual transfer between web-member walls and gusset plates. Because the number of joints in these huge platforms is limited compared to the over-all size, a proper design of these joints is even more important than was the case for the many joints in the smaller, but multi-legged towers. A failure of one of those ultra-large joints could well cause the complete collapse of such a structure. Under these circumstances an accurate analysis of the large joints is of the greatest importance, together with information regarding the expected behavior of such joints under critical alternating load conditions. Recent applications of photoelastic model techniques have proved to be quite effective in evaluating the elastic behavior of such joints. Although a complete study of such connections is quite well possible with present-day photoelastic techniques, it might often be feasible and necessary to limit the objectives and to restrict these investigations to the study of a specific aspect of the joint. Another very promising avenue of approach to solve the complex stress pattern in these connections seems to be the recent development of digital computer programs. In this category, cylindrical shell programs and finite element methods for more complex configurations have

Jan 1, 1967

International Trade in Nonmetallic Minerals. BY J W FURNESS AND E W PEHRSON (Man &. Met, Sept, 432 2500 words) International trade in nonmetalic minerals (exclusive of fuels) is dominated largely by fertilizer raw materials such as phosphate rock, potash, nitrates, sulphur and pyrites and the miscellaneous group of minerals including asbestos, mica, graphite, fluorspar and china clay Cost of trans¬portation deters any substantial movement of the building materials which usually occur widely in nature and are thus available near consuming centers at relatively low cost This paper, which presents a summary for 1932 of the world production, consumption and principal trade relations of asbestos, china clay, fluorspar, graphite, gypsum, mica, phosphate rock and potash illustrated by world charts, is based on an original study of 15 nonmetallic minerals conducted by the U S Bureau of Mines Practical and Legal Aspects of Mme Financing See METAL MINING Economic Significance of High-grade Concentrates See MILLING AND CONCENTRATION

Jan 1, 1937

Abbott, Robert H., (S'42) Agricultural & Mech. College of Texas, College Sta.. Texas. Abrahamson, Guy C., (S'43) Univ. of California, Berkeley. Calif. Abrego, Alfredo, (S'43) Texas College of Mines & Metallurgy, El Paso, Texas. Ackermann, K. G., (S'43) Univ. of Alabama, University, Ala. Adamec, Lew, (S'42) Colorado School of Mines, Golden, . Colo. Adams. Charles E., (S'42) Univ. of California, Los Angeles, Calif. Adams, Charles W., (S'30) Asst. Met., Canada Foundries & Forgings Ltd., Welland, Ont., Canada. Adams, John W., (S'42) Univ. of Texas, Austin, Texas. Adams, Karl S., (S'43) Univ. of New Hampshire, Durham, N. H. Adamson, Charles R., (S'41) Univ. of Utah, Salt Lake City. Utah. Adler, A. G., (S'41) Met. Engr., Flotation Operator Helper. Utah Copper Co.. Garfield, Utah. Adler, Frank J., (S'42) Colorado School of Mines, Golden, Colo.

Jan 1, 1943

By W. E. Wrather

DURING the war the mineral industry, and metal mining in particular, extended itself more than any other to attain the limit of its productive capacity. Likewise, probably no other industry went quite so far toward jeop¬ardizing its own economic future through depletion of material reserves. Once we looked to Europe for most of the manufactured goods we needed. Our own limited mineral requirements were easily supplied from mines near the Eastern seaboard. With expansion and industrialization, our mineral needs increased in proportion, and the centers of mining activity moved westward to Michigan, Wisconsin, Minnesota, and the Tri-State district, where seemingly inexhaustible high-grade deposits of iron, copper, lead, and zinc ores were opened and rapidly developed.

Jan 1, 1946

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By L. P. Durham

DuRing the early mine development period, 1929 and the first part of 1930, a 300-ton pilot-plant concentrator was built at Nkana mine of the Rhokana Corporation, Northern Rhodesia. This plant operated from May 26, 1930 until Oct. 26, 1931, treating 101,080 tons of Nkana ores and producing 4372 tons of concentrate. The plant was built, primarily, as a test unit to determine the grinding characteristics, floatability, etc. of the Nkana ores and other ores of the Rhodesian copper belt and to supply sufficient data on which to base the design of a 5000-ton concentrating plant at Nkana mine. The test unit operated wholly on development ores and no attempt was made to grade or select the ores from any section of the mine. The average assays for the 17 months of operation are given in Table 1. The first ground was broken for the 5000-ton concentrator during June, 1930, and the construction of the plant was completed in November, 1931. The plant started on Dec. 10 and has operated continuously since that date: The whole of the concentrating plant is compact and closely connected, yet with sufficient space for expansion of all sections up to 20,000 to 25,000 tons per day capacity. Mining operations are carried on along a length of about four miles on the easterly limb of the Nkana syncline. This length includes the North orebody, from which all production has thus far originated, and the Mindola orebody, now being developed for production. The ore-bearing measures in the North orebody are leached for some 75 ft. below the surface; the oxidized zone varies in vertical extent from 100 to 150 ft. Practically all the ore below the 200-ft. level is sufficiently

Jan 1, 1935

A filled stope is one in which the support for walls and men and, at times, for the back of ore, is furnished by waste rock or sand tailings. The filling may be rock sorted out in the stope or from the walls, develop-ent, or the surface. The orebody is mined in sections, each practically an open or timbered stope, filled wholly or in part before adjacent ground is attacked. As a rule, the filled-stope method is limited to overhand flat-back, stepped-face, or rill stopes. The examples given are Copper Range, Iron Cap, Verde district, Zaruma district, Lucky Tiger, and Silver King Coalition.

Jan 1, 1925