Search Documents

By C. H. Mathewson

CHARACTER OF THE WORK IN HAND IN planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100° C. to 1,000° C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,1 in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper.

Jan 7, 1916

By N. S. Stoloff, K. R. Jordan

The temperatwe and grain size dependence of the mechanical avoperties of ordered and disordered Fe-49 pct Co-2 Pct V were investigated. The yield and flow stresses obeyed the Hall-Petch relationship u = ai + kd-&apos;I2. Ohdering reduced the intercept stress cjj and raised the Petch slope, k, at all temperatures. Ordering also increased the temperatwe dependence of k. The ductile to brittle transition temperature increased with order and grair~ size. Cleavage fracture was nucleation limited and the fracture stress did not zlary linearly with d-&apos;". A quantitative test of the Cottrell-Petch fracture theory (and recent modifications which consider the influence of slip mode), demonstvated that this theory is not applicable to FeCo-V. COTTRELL&apos; and etch&apos; independently suggested that a criterion for cleavage failure at the yield point, a,, based on dislocation pileups at a grain boundary or other obstacle to dislocat.ion motion, is: aYYkd&apos;I2 1 opy [ll or, equivalently, aikz,d112 +k:)bpy [2] where a, and ky are the Hall-Petch intercept and slope, respectively, 2d is the grain diameter, P is a geometric factor dependent on the macroscopic ratio between shear and tensile stress, p is the shear modulus, and y is the true elastic surface energy. When the product of quantities on the left side of the equation is equal to or exceeds that on the right, cracks should be able to nucleate and propagate at the yield stress, as shown schematically in Fig. 1. Therefore a high intercept stress, high Petch slope, or coarse grain size favors brittleness. petch3 associated the existence of a ductile to brittle transition in ferrous alloys with the temperature dependence of ai. One of the earliest modifications of the Cottrell-Petch theory was presented by ~rmstrong,~ who derived an expression for transition temperature in terms of several measurable flow and fracture parameters. The latter paper was able to rationalize situations in which the transition temperature increases with decl-easing grain size, as in the case of molybdenum,&apos; and also suggested that Ppy should be a function of grain size as well as temperature. More recently Johnston et a1.6 and Smith and worthington7 have suggested that the temperature or composition dependence ol&apos; ky must also be taken into account if there is any cha.nge in deformation mode, as from wavy to planar slip, or wavy slip to twinning, with change in temperature or solute content. Armstrong %as suggested that for hcp metals changes in o;k,dw> o;k,d1/2< / is / ^^^^ / / y_______________________________________ d-"2 Fig. l—Schematic representation of grain size dependence of yield stress, cry, and fracture stress, CTF. Intersection defined by Cottrell-Petch equation. slip mode should be incorporated in the theory through changes in the critical resolved shear stress for the slip system which controls ky. The purpose of the present investigation was to critically test the modified677 Cottrell-Petch theory of fracture in the superlattice alloy Fe-49 pct Co-2 pct V, by studying the grain size dependence of the yield and fracture stresses over a range of temperatures, in conjunction with an investigation of slip mode and fracture behavior. Previous work has shown that long range order results in a sharp decrease in flow stress, a small increase in work hardening rate and a drastic upward shift in the ductile-brittle transition temperature of F~CO-V.~&apos;~ The only comprehensive study of slip character in this alloy has been reported in a preliminary account of the present investigation.10 EXPERIMENTAL PROCEDURE The experimental work was carried out on material produced from a 10 lb vacuum melted ingot, of composition 49.32 wt pct Co, 2.09 wt pct V, balance Fe. 30-mil thick sheet samples with a 1; in. gage section were machined from cold rolled stock. The degree of cold work ranged from 85 pct for the finest grained samples to 5 pct for the coarsest grain size. Details of ingot fabrication are reported elsewhere." Equi-axed grain sizes in the range 12.7 to 75.4 p were obtained by annealing for varying times at 850°C. (Re-crystallization annealing time, rather than temperature , was varied to control grain size to insure that samples of all grain sizes contained equivalent quenched-in vacancy and interstitial concentrations.) Grain sizes were measured by the line intercept method on several specimens of each grain size. Following recrystallization, all samples were disordered by quenching into iced brine.

Jan 1, 1970

By J. J. Foster

MOST of us will, I think, agree that never before in the history of the coal industry has the human side of our business been so important as today. Since, even in wholly mechanized mining, labor cost is such a large percentage of out total cost we are all deeply concerned not only about the present attitude of our employees but particularly about the future, when the industry returns to a "survival of the fittest" basis. Many things could and should be done about our employee relations in the coal business. Failure to recognize these obligations and do something about them may lead to serious consequences, the least serious of which will be the loss not only of many of our better employees but a large portion of our potential employees, as they graduate from our schools to other in¬dustries. Some of these things should be handled by the industry as a whole whereas others should be done by individual companies. Due to varying conditions and size of organizations it would, at best, be necessary to vary a program to meet the individual needs of each operator.

Jan 1, 1945

By B. F. Tillson

ALTHOUGH most accidents occur through the A carelessness or misfortune of the workmen; that is no reason why we should not take all physical precautions practicable. The best way to approach the problem of mine safety is to acquire a personal feeling of responsibility for the accident and then plan how it might have been prevented had we known that it was to occur. A statistical analysis of the physical conditions contributory to accidents will give an indication of some of the methods or mechanisms that should be revised or safeguarded. The handling of rock or ore is a common source of minor injuries. Freedom from accident when mucking largely depends on the skill and care of the workman; this also is true, to a certain degree, to loading cars from chutes, but much can be done in the layout of chutes and their equipment to provide equal safety with less skill. Permanent stagings, or rigid units that may be easily assembled, should be provided so that the men handling the chute boards or gates and barring the jammed chunks will have a convenient safe footing for their operations. A stance to the side of the chute mouth is to one in front, because a man will not be liable to be struck by flying lumps or his bar, should it he caught in the mass, yet in many mines the workmen face the chute when loading a car. Fig. 1 shows the operation of a plank chute having special latches which support the chute boards in such manner that they may be conveniently dropped into place to stop the flow of ore.

Jan 1, 1926

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By H. M. Woodroffe, H. K. Conn, S. J. Rice

World production of asbestos is estimated to be at a current level of almost 3.5 million tons, having more than doubled in the past ten years. A substantial part of the increase has been due to a rapid expansion in the Soviet Union. Production from that country during 1964 is estimated at 1.5 million tons and, as a consequence, Russia has displaced Canada as the leading world producer. Although traditionally the asbestos mining industry has been centered near Sverdlovsk in the Urals, two new producing areas have been under development for some time. It is expected that a new mine will be in operation in 1965 near Kiembi, Kazakhstan, some 300 miles south of Sverdlovsk, and an- other mine at Aktrovak in Tannu-Tuva, west of Lake Baikal. These developments will provide a significant increase in the production capability of Russia. Although internal consumption is expected to increase with the addition of new asbestos- cement producing facilities now under construction in Russia, there is some speculation that exports will also increase.

Jan 2, 1965

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By Elmer W. Pehrson

Minerals have played a prominent role in the affairs of man and nations since time immemorial but with the advent of the industrial revolution, expanding use of the products of the mineral kingdom became synonymous with the material progress of mankind. Individuals and business groups have recognized this fact so have been aggressive in searching for and utilizing mineral resources, with notable success. Indeed, their achievements are primarily responsible for the present Machine Age. On the other hand, until recently the body politic has failed to grasp fully the essentiality of minerals although, at times, access to mineral supplies has been an important factor in the political maneuvers of nations. This chapter is concerned primarily with the broader political and economic relationships of mineral resources to the world economy, and with the internal and external actions of nations in the field of minerals. Many factors that condition the mineral economy of regions and the world as a whole, influence the internal and external affairs of individual nations. The more important of these are: 1. The nature of man&apos;s dependence on minerals. 2. The problems resulting from the unique characteristics of mineral occurrence. 3. Geopolitical concepts. 4. Minerals and world power. Actions of individual nations affecting their mineral economy seek two basic objectives: 1. Attainment and maintenance of prosperity. 2. Military security. Other objectives may be cited but on careful analysis they become integral parts or extreme phases of the two points noted above. For example, the twentieth century aggressions of the USSR, Germany, Italy, and Japan might be considered as direct bids for world power but they also can be interpreted as exaggerated or mistaken efforts toward military security and peacetime prosperity. Similarly, trade barriers, nationalization of industries, foreign exchange manipulations, taxation, monopolistic prac-

Jan 1, 1964

By J. G. Thompson

PROJECT 8411 of the U. S. Bureau of Standards, sponsored by the Iron and Steel Division of the A.I.M.E., is an attempt to define more concisely than has been possible heretofore the accuracy and the Limits &apos; of usefulness of the &apos; various methods now in use for the determination of oxygen as it exists in ferrous materials. It originated in correspondence between John Johnston and other metallurgists, and was brought to the attention of the Iron and Steel Division of the Institute at the Annual Meeting in February, 1933. As reported in MINING AND MET,ALLURGY, Vol. 14, page 152, March, 1933, "Dr. Johnston introduced, and those present adopted, a resolution that the Iron and Steel Division of the A.I.M.E., believing that a careful comparison of the several methods now in use for the analysis of steel for nonmetallic elements such as oxygen is highly desirable, heartily endorses the proposal that the U. S. Bureau of Standards act as a clearing house " in this matter, undertaking the final preparation and allocation of identical samples to those laboratories willing to collaborate in this important question, and collate the results re- ported back to the Bureau.&apos;"

Jan 1, 1934

By R. W. Gurry

WHEN a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, vet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. EXPERIMENTAL PROCEDURE Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;1 it suffices to state here that the carburization lasted about 140 hr. at 760°C. (1760°F.) and 44 hr. at 1110°C. (2030°F.), these periods being long enough-on the basis of the calculations presented later-to ensure that the specimen was about 9.99 per cent saturated at each temperature. The speci¬men was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully [carburized] specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By Carl A. Allen

Page Introduction................... 367 FactoRs Affecting the Choice of Method......... 367 Review of Stoping Methods.............. 368 Underhand Stoping................ 368 Overhand Stoping................ 370 Longitudinal or Flat-Back Stoping........... 371 Rill-Cut Stoping................. 372 Saw-Tooth Back Stoping.............. 372 Shrinkage Stoping................ 372 Combination Stoping................373 Side Stoping.................. 374* Breast Stoping................. 374 Sublevel Stoping.........,....... 374 Square-Set Stoping................ 376 Filling Methods................. 376 Caving Methods of Mining......... 376 Top Slicing.................. 377 Sublevel Caving................. 379 Block Caving ................. 380 Back Caving into Chutes.............. 381. Costs of Mining Methods.............. 382 Costs of Willing and Blasting. Comparison of Stoping Methods ... 383 Lighting................... 386 Timbering and Handling Ore in Stopes.. A Comparison of Square-Set and Top-Slicing Methods..............386 Tramming.................... 380 Mining oF the Massive Porphyry CoppeR Deposits ....390 Utah Copper and Boston Consolidated Mines.....391 Ray Consolidated Mine.............. 392 Miami Mine.................. 392 Inspiration Mine................ 395 Ohio Copper Mine...........395 Development.................... 398 Appendix..................... 399 Costs of Mining................. 399 Costs of Development............... 406

Jan 1, 1915

By C. F. Tolman

In February 1913, Prof. L. C. Graton and Dr. Joseph Murdochl presented to the American Institute of Mining Engineers a notable contribution to economic geology under the title The Sulphide Ores of Copper. The value of the work was recognized by mine operators, and Mr. Graton was assisted in his plan to extend his investigations, by the organization of a commission to undertake a "secondary enrichment investigation." In this work he secured the cooperation of the Geophysical Laboratory of the Carnegie Institution of Washington. The report2 on the chemical phascs of the investigation has just been published. Incidental to investigations3 carried on in our laboratory of Economic

Jan 1, 1916

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By B. DE MARE

THE No. 6 open-hearth furnace at the plant of the Worth Steel Co., Claymont, Del., is the first to be rebuilt according to the Kuehn system. This as well as the other five furnaces at Claymont, has a nominal capacity of 75 tons, but the actual charge is about 242,000 lb. No hot metal being available, the pig-iron is charged cold. Oil of low grade with an asphalt base is used as fuel. These two items have to be kept in mind when discussing the actual fuel consumption. Careful records have been kept covering a five weeks run and the following is a brief summary of them The time required to heat the furnace preparatory to charging from the time a wood fire was started until charging commenced was 36 hours. This, I understand, is much less than with furnaces of standard design. The draft of the furnace, as shown by a gage in the stack-flue, is 1.25 in. The maximum draft with new checkers on former runs was 1.50 in., this draft gradu¬ally decreasing as the checkers closed up. Both of the first helpers claim the present draft is all they need for the proper working of the furnace, and, as with the Kuehn regenerators the draft remains practically the same from beginning to end of a run, this is satisfactory.

Jan 1, 1929

By J. H. Smith, H. W. Paxton

X HE recent investigation of Butler, McCabe, and paxton&apos; on the vapor pressure of manganese gas in equilibrium with Mn-Fe alloys has been extended to include the iron-rich solutions and alloys in the two phase equilibrium region. The study of the phase equilibrium by Kurnakov and Troneva2 and the extensive reviews of the Mn-Fe system by Hansen,3 and Hellawe114 are not in agreement with regard to the location and extent of the equilibrium between the solid phases of fcc y and complex P in the temperature range above the eutectoid temperature of approximately 975Kwhere 0 decomposes to y and bcc a. An evaluation of the existing equilibrium data is confronted with the conflicting results presented by various investigators who used techniques requiring a quenching treatment to retain the high-temperature equilibrium or encountered temperature hysteresis during thermal analyses. The difficulty of suppressing the transformation of the manganese-rich concentrations of the y-solid solution during quenching has been well etablished.&apos; To avoid this uncertainty the phase equilibrium was investigated at temperature by measuring the partial pressure of manganese gas in equilibrium

Jan 1, 1962

By A. Taylor

IN a previous communication,l the quaternary system Ni-Cr-Ti-A1 was described in detail and it was shown how certain alloys used for high-temperature applications could be construed as consisting of Ni,Cr suitably modified by the addition of aluminum and titanium in relatively small amounts. With the correct aging treatment, the ordered face-centered-cubic Berthollide phase, y&apos;-Ni,Al, could be precipitated from the face-centered-cubic primary y-solid solution. By increasing the proportion of titanium with respect to aluminum, it was also possible to precipitate the very brittle hexagonal-close-packed Daltonide phase, ?-Ni,Ti. From the nature of the system it seems reasonable to expect the y and y&apos;-phases to take appreciable amounts of cobalt and iron into solid solution. In the case of the present investigation it was decided to confine the work to iron additions only. This element may be introduced in two quite distinct ways: 1) as a simple replacement for nickel; and 2) as a replacement for chromium, titanium, and aluminum. The second method of iron addition forms the basis of the present investigation, which is, in effect, a study of the pseudo-quaternary system Ni,Cr-NiPe-Ni,Ti-NLAl. For purposes of reference, Figs. 1, 2, and 3 have been included and illustrate the quaternary system Ni-Cr-Ti-A1 described in the previous paper along with sections through N&Cr-Ni,Ti-Ni,Al at 750" and 1000 "C respectively. As will be shown below, the pseudo-quaternary system with components Ni,Cr, NiPe, Ni,Ti, Nihl is remarkably similar in many ways to the face defined by Ni,Cr-Ni,Ti-Ni,Al because of iron re-

Jan 1, 1958

By J. G. Early, F. V. Lenel, G. S. Ansell

The isothermal shrinkage rates of copper-powder compacts were determined in the temperature range from 760o to 1060oC. The rates for compacts fabricated from a pure spherical copper powder were compared, on the one hand, with those fabricated from a spherical powder containing a dispersion of aluminum oxide in the copper matrix and, on the other hand, with those fabricated from a pure copper powder having irregularly shaped particles. The irregular copper-powder compacts shrank much faster than the spherical copper-powder compacts and these, in turn, shrank faster than dispersion -strengthened copper -powder compacts. The experiments were run under a small external load. By varying this load, the stress dependence of the isothermal shrinkage rate could be measured for compacts from spherical-copper powders. This stress dependence was found to be approximately proportional to the 4th (dispersion-strengthened alloys) or 4.5th (pure metals) power of the stress. It is concluded that the material-trans port mechanism is due to dislocation climb rather than to Herring-Naharro creep. In this investigation the isothermal shrinkage rates of compacts made of copper powder with an average particle size of 70 g in the temperature range from 780o to 1060°C were studied. The aim of the investigation was to determine the mechanism of material transport responsible for the shrinkage of these compacts. Since the phenomenon observed in this investigation was shrinkage of compacts at high temperatures, it will be necessary to consider all the material-transport mechanisms possible in sintering. It is unlikely that evaporation and condensation, surface diffusion, or even volume diffusion of vacancies, in which surfaces of small radius of curvature are vacancy sources and those of larger radius of curvature vacancy sinks, will materially contribute to a sintering process involving shrinkage, i.e., one in which the centers of adjacent particles move towards each other. The two principal mechanisms which were considered were the so-called Nabarro-Herring mechanism and a plastic deformation mechanism by dislocation movement. Both of these mechanisms were originally conceived to explain creep, i.e., the plastic deformation of metals at elevated temperatures under a constant applied stress. The shrinking of metal-powder compacts which was studied in this investigation can be readily treated as a creep process. This means that the shrinkage rates observed are considered as creep rates under the influence of an applied stress. It is true that the stresses in sintering experiments are generally not constant but decrease continually with time, but, by considering creep rates or shrinkage rates over a relatively short time interval, the small changes in stress during this time interval can generally be neglected. Nabarro-Herring microcreep is a high-temperature deformation mechanism which is caused by a diffusional flow of vacancies from boundaries under a tensile stress towards those under a compres-sive stress. Herring1 has shown that in this type of microcreep the strain rate e is proportional to the applied stress and follows an equation of the form ma, aexp(-Q/RT) [l| where <j is applied stress, Q is the activation energy for self-diffusion, R is the gas constant, and T is the absolute temperature This type of creep can explain the shrinkage of a porous compact. The surface of the pores are subjected to the tensile stress of surface tension, while the grain boundaries are under a compressive stress also due to surface tension. Vacancies diffuse from the pore surface through the lattice to the grain boundaries, where they are eliminated. In order to maintain vacancy equilibrium at the pore surface the vacancies leaving the region of the pore surface are replenished from the volume of the pore, which means that the pores shrink.

Jan 1, 1964

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By F. C. Kelley, L. L. Wyman

In order to clarify and amplify the existing data concerning the action of the cementing material in cemented tungsten carbide alloys, the authors have initiated this investigation of the entire range of cobalt-tungsten carbide alloys. Inasmuch as the ultimate objective is relative to what actually goes on during the sintering of cemented tungsten carbide materials, this work was necessarily restricted to heat treatments similar to those used in actual production of these materials. In the course of numerous experiments, the authors have noted several conditions that indicated that there was a solubility to be considered. Among these factors are the following: 1. Many of the alloys showed a much larger amount of binding constituent to be present than could possibly be accounted for by the cobalt content. 2. In many areas, grains of the carbide constituent are much larger than the particles of carbide originally added. In addition, these grains are of very regular contour. 2a. In samples of cemented tungsten carbide which had been fused in the atomic hydrogen torch in the presence of excess binder constituent, immense grains are formed, and their shapes are very regular. This is also true when the cemented tungsten carbide of 13 per cent. Co content is fused alone in the atomic hydrogen torch. Contrary to general expectation, chemical analysis of this material, after fusion in the atomic hydrogen torch, checks the analysis of unfused material. 3. In making the cemented tungsten carbide materials by the process of exerting the pressure at the time of heating a certain portion of the &apos; contents squeezed out of the mold. Chemical analysis has shown that this material contains approximately 12 to 20 per cent. of tungsten. The microstructure shows a cored dendritic structure interlaced with eutectic network, and some graphite, as shown in Fig. 1. 4. Thermal analysis of these materials has consistently indicated an arrest point close to 1350" C.

Jan 1, 1931

By T. N. Dixon, J. E. Briggs

A study was made of numerical techniques for solving the large sets of simultaneous equations that arise in the mathematical mode ling of oil reservoir behavior. It was found that noniterative techniques, such as the Alternating Direction Implicit (ADI) method, as well as some other finite difference approximations, produce oscillatory or unsmooth results for large time steps. Estimates of time step sizes sufficient to avoid such behavior are given. A comparison was made of the Point Successive Over-Relaxation (PSOR), Two-Line Cyclic Chebyshev Semi-Iterative SOR (2LCC), and iterative ADI methods, with respect to speed of solution of a test problem. It was found that, when applicable, iterative ADI is fastest for problems involving many points, while 2LCC is preferable for smaller problems. INTRODUCTION With the advent of high speed, large memory, digital computers, there has been an increasing emphasis on the development of improved methods for simulating and predicting reservoir performance. Two-dimensional, three-phase reservoir models with various combinations of PVT effects, as well as gravity and capillary forces, are common throughout the industry. Such models are also available through consulting firms, to anyone desiring to use them. Three-dimensional models will probably be practical in only a few years. We conducted a study of some of the numerical methods used for solving the large sets of simultaneous equations that arise in such models. A typical set of equations for a reservoir model is shown below:

Jan 1, 1969