Search Documents

By Craig R. Barrett, Oleg D. Sherby

The creep characteristics of four pure metals with widely Varying stacking-fault energies (silver, copper, nickel, and aluminum) were evaluated above 0.5Tm. Creep tests were performed under conditions of constant atomic diffusivity and constant stress over the elaslic modulus. The sleady-state creep rate, Es, was found to he a funclion of the THE most common empirical representation of the steady-state creep rate, Es, at high temperatures and intermediate stresses is of the form where a is the applied stress, E is an elastic constant, A and n are constants (n is typically stacking-fault energ, y, such that Es is proportional to y3,5. In addition, it was uncovered that the primary creep strain and the strain to fracture increased with increasing y, and that the ratio of initial to steady-state creep rate decreased with increasing y. about 5), Q is the activation energy for creep (usually equal to that for self-diffusion), and kT has its usual meaning. sherbyl and McLean and ale' have used this expression to correlate creep data for a number of pure metals. An interesting aspect of Eq. [I] is the absence of any dependence on the stacking-fault energy. While most creep data seem to obey the stress and temperature dependence predicted by Eq. [I], when data for several metals are put on a master plot they do not fall on a common line but form a band. The width of this band corresponds to a variation in Es of 102 to l03. sherbyl attempted to explain this band by assuming that a grain-size effect was present which led to the observed variation. On the other hand, Felt-

Jan 1, 1965

By H. M. St. John

THE melting department is the heart of the foundry. From it clean metal flows to the molding floor, in the right quantity, at the right time and at a sufficiently low cost-or, if not, the foundry fails to thrive. Since it is our purpose here to discuss present-day melting practice in the foundry, it may be well at the start to emphasize the wide differences in foundries and the conditions under which they must operate in order to reach the goal stated in the first paragraph. In every foundry, large or small, jobbing or captive, the same factors must be dealt with but they are of varying consequence and must be dealt with in varying ways in different foundries. Particularly in the nonferrous industry, there is so wide a variation in the composition of alloys used and in the character of castings made that no one type of furnace, nor any one method of operation, can be expected to produce the best results at all times. The present discussion will not attempt to include all nonferrous metals. It is intended to cover only the copper-base alloys in which copper is the dominant element, most of which are commonly known as brass or bronze. The discussion is further limited to the melting of these copper-base alloys for use in sand-casting foundries. Die-casting plants, the brass-rolling mills and certain other metal industries have melting problems peculiar to those industries, which will not be considered here. The following considerations are elemental in all foundries and are listed in what is believed to be the relative order of their present-day importance: I. The melting department must meet the foundry's requirement for dean, fluid metal, of specified composition and purity, at a temperature suitable for the work the foundry has in hand. This is the prime consideration in any foundry, at any time, anywhere. 2. Working conditions surrounding the melting furnaces and attending their use must be good. 3. The cost of molten metal at the mold must be as low as possible. 4. The operating characteristics of the furnaces must be sufficiently flexible, to meet normal variations in foundry requirements. 5. The operation and maintenance of the melting equipment must not require more skill and experience than is available in the particular foundry in question. METAL QUALITY It is not a function of the melting furnace to refine or improve the quality of the metal but simply to melt it without impairing its quality. Good practice requires, therefore, that care must be taken to supply the melting department with metal of inherently good quality, assured by specification or otherwise, having all the properties necessary to produce the castings desired. An alloy contains a number of primary elements, which must be present in definite proportions if the castings made from it are to have the desired properties. If the castings are made to a customer's specification, this will state the range within which these principal elements (for example, copper, tin, lead and zinc) are permitted to vary.

Jan 1, 1946

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By Charles A. Stetefeldt

This treatise is the sequel of a paper on "Russell's Improved Process for the Lixiviation of Silver-ores," etc., read at the Chicago meeting, in May, 1884, and published in the Transactions, vol. xiii., page 47. The facts it presents are principally compiled from Mr. Russell's notes on his practical experience gained in various places where the Russell process has been introduced. For a complete understanding of this paper a perusal of my former one is desirable, as can be seen from the frequent references here made to it. All silver-ores that do not carry a large percentage of lead or copper can be treated by Russell's process with success and economy. I do not mean to create the impression that from ores containing considerable quantities of lead and copper a high percentage of the silver cannot be extracted by this process. Such ores, however, will, in many localities, be reduced to better advantage by smelting. In case lead-bearing silver-ores are suitable for concentration, it may be profitable to concentrate the ore by Krom's dry system, obtaining a smelting-product high in lead, and to lixiviate the tailings and the dust. This plan has been adopted in a mill recently erected in Cortez District, Nevada. The dry system of concentration deserves the preference because it delivers the tailings and the dust in a condition ready for chloridizing-roasting. In wet concentration the drying of the tail ings would be expensive, and there would be a considerable loss of silver in slimes. Oxidized ores, containing silver chloride and lead minerals, may be lixiviated after crushing, and the tailings may be concentrated for lead. In this case wet concentration would be most suitable. This has been done at the Old Telegraph Mine, Utah. I would give, however, the preference to dry concentration in all cases which, of course, requires that concentration should precede lixiviation. The Russell process is also adapted to the treatment of tailings resulting from ores which have been worked either by the old

Jan 1, 1887

By E. J. Rapperport, M. F. Smith

A presentation of the W-Ru constitution diagram is given. Techniques utilized in the determination of phase boundary values include electron micro-probe analysis of two-phased alloys and diffusion couples, as well as normal metallographic and X-ray methods. The primary features of the diagram are: 1) a terminal solid solution of ruthenium in tungsten with a maximum solubility of 23 at. pct Ru at 2300°C; 2) a terminal solid solution of tungsten in ruthenium with a maximum solubility of 48 at. pct W at 2205°C; 3) a o phase of maximum breadth about 6 at. pct based on the composition W3Ru2 which forms peritectically from the melt at 2300°C, and which decomposes eutectoidally at 1667 °C to form a twigs ten and 0 ruthenium; 4) a eutectic at 45 at. pct Ru and 2205°C with the products being o plus ß ruthenium. THE W-Ru diagram has previously been studied only in a cursory fashion. Raub and alter' obtained a 1400°C isotherm in which they observed no intermediate phases, and on which they established the limits of solubility as 36.5 at. pct W in ruthenium and about 1.5 at. pct Ru in tungsten. In addition, Obrowski2 found a o phase forming peritectically from the melt and existing only above 1650°C. Below this temperature the phase was presumed to decompose eutectoidally. The present work finds the diagram as given in Fig. 1. I) EXPERIMENTAL PROCEDURE The materials used for alloy preparation in determining the W-Ru constitution diagram were 99.9 pct pure ruthenium powder supplied by Baker Chemical Co., and 99.9 pct pure tungsten powder from General Electric Co. Typical analyses of these elements are given in Table I. Initial alloys at 10 at. pct intervals were prepared from the metal powders by the following method. Powders sufficient for 25 g of the alloys were weighed out with an accuracy of 0.1 mg and blended mechanically. After blending, the powders were compacted, in a steel die, at approximately 30,000 psi. The compacts were sintered in an electric vacuum furnace in order to remove adsorbed gases and to achieve partial densification prior to arc-melting. Vacua of 10-4 mm Hg or less were maintained in sintering as the furnace temperature was raised to approximately 2000°C. Sintering times ranged from 10 to 20 hr. The sintered compacts were arc-melted under a protective atmosphere of purified helium. Melting was conducted on a water-cooled copper hearth, utilizing a nonconsumable tungsten electrode. In the melting process, each alloy was turned over and re-melted on opposite sides from four to six times to ensure complete melting and to eliminate gross in-homogeneities. The arc-melter used had a vacuum capability of 5 X 10-6 mm Hg, and a leak rate of about 20 -liters per hr. Chemical analysis techniques for refractory metal-platinum group metal combinations are not well-established; therefore, composition control and determination depended principally upon weight-loss observations and calculations. This consisted in weighing each alloy after sintering and after arc-melting, and calculating the maximum and minimum composition values, assuming the total weight losses to be first all tungsten, and then all ruthenium. Since composition uncertainty was directly related to weight loss, care was taken to minimize losses in handling, compacting, and melting. Prior to homogenization and equilibration the as-arc-melted alloys were analyzed in several

Jan 1, 1964

James GayleY, New Pork City (communication to the Secretary*) :—The main thing that is sought after in this matter is that all purcliases shall be made by analysis. This is done already in special lines, as in the manufacture of various grades of steel in which phosphorus, silicon and sulphur are specified within narrow limits, and I quite agree with Mr. Cook that specifications, which are over-rigid in unessential particulars, should be avoided, as they defeat their own purpose because unreasonable requirements permitting no variation are practically not fulfilled, and it is impossible to specify grade

Jan 1, 1905

By J. A. Jaekel, W. C. Aitkenhead

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U3O8. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U3O8 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pcl U3O8 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8. with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct. It has been concluded that a successful method for floating autunite has been developed and that the mediocre results from the Midnight argillite ore are probably caused by the presence of some other uranium mineral or minerals less amenable to these reagents. The experimenters tested a third type of Washington ore, found on the Northwest Uranium Mines Inc. property on the Spokane Indian Reservation. This is a conglomerate of pebbles and small boulders of partially decomposed granite and is shot through with autunite. Its characteristics lie between those of the Midnight ore and the granite ore from the Spokane district. It responds better than the ore from Midnight but not as well as that from Mt. Spokane. As the fatty acids are the only type of collectors showing promise, investigation has been concerned with these acids and the optimum conditions for their use. The first method for treating the argillite ore from the Spokane Indian Reservation made use of Cyanamid's R-708 as a collector, a tall oil product described as a substitute for oleic acid. Although the investigators proved that R-708 is a collector for autunite when mixtures of autunite and silica sand are used, results on the ore were mediocre. Tests of other fatty acids revealed that the solid fatty acids of the saturated series are collectors for autunite and that their collecting power increases with the length of the carbon chain. The even carbon members of the whole series were tested from the 10 carbon acid (capric) to the 22 carbon acid (be-henic). The least expensive collector, stearic acid (18 carbon), proved to be a good one, so this was used in most of the tests. In first attempts with stearic acid, the collector was dissolved in various hydrocarbons and the solutions were added to the flotation cell. Cyclohexane, gasoline, fuel oil, kerosene, and other solvents were tried. Small amounts of high grade concentrates could be brought up, but recoveries were low. Finally emulsions of stearic acid were tried. It was discovered that stearic acid alone has little collecting power except when conditioning is carried out at high temperature. When hydrocarbon solvents were also present, it proved to be an excellent collector. An example of one emulsion that proved satisfactory for some ores is given as follows: 1 part stearic acid by weight, 1 part sodium oleate by weight, 1.2 parts kerosene by weight, 100 parts water. In some successful tests part of the stearic acid was replaced by oleic acid. The emulsions were made by agitating the stearic acid and sodium oleate together with hot water, then adding the kerosene and agitating while cooling. In the five tests reported in Table 1, 650 g of ore were ground with 650 cc water in a laboratory rod mill. The pulp was filtered to eliminate excess water and the ground ore transferred to a stainless steel beaker for conditioning at high pulp density. In most of the tests sodium hydroxide was added to the conditioner during agitation, then the collector emulsion, and finally the sodium silicate. The amount of alkali was adjusted to give a pH of 8.5 to 9.0 in the flotation cell. After conditioning the pulp was transferred to a laboratory flotation cell and the test completed in a normal manner. It is interesting to note that a deposit of high grade concentrate forms on the conditioning agitator and in the conditioning vessel, and at times on the agitator of the flotation cell itself. A few grams of concentrate running as high as 4 pct U3O8 were recovered from the conditioner when Midnight ore containing less than 0.2 pct U3O8 was treated. In the examples given in Table I this conditioner concentrate is calculated as part of the total concentrate. The authors have not yet fully explored the possi-

Jan 1, 1960

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a manmade force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by the U.S. Bureau of Mines, as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps, direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1973

By H. R. Banks

THE Sullivan concentrator has completed 20 years of operation. During this period a considerable amount of data has been accumulated concerning the characteristics of several types of flotation machines in their application to the problem of the differential separation of the lead sulphide, zinc sulphide and, in more recent times, iron sulphide, in the ore from the Sullivan mine. It is the author's intention to sketch briefly experiences encountered when the several types of flotation machines were introduced into the flow. ORIGINAL FLOTATION EQUIPMENT AND ORE The original flotation equipment consisted of four 18-cell lead-roughing machines, whose concentrate was cleaned in an 8-cell and recleaned in a similar 8-cell machine. Zinc concentration was carried out in four 18-cell machines. One 8-cell zinc re-treatment machine received the reground zinc middling. The 168 cells handled some 3000 tons of original daily feed. These cells were of the standard Minerals Separation type, equipped with 24-in. impellers. Spindles were driven through geared line shaft at a speed of 255 r.p.m. The impellers were the 45° type, except for the last three cells of the zinc-rougher machines, which were of sub-aeration type, with full bottom shroud and half shroud for the top side of the impellers. Four-pound air was introduced. This recognition of the benefit of intensified flotation operation for "gleaning" was an important phase in the early operation and will be discussed further on in this paper. Sullivan ore during this period is described as a finely disseminated mixture of four sulphides, totaling 90 per cent made up of 13.6 per cent galena, 14.4 per cent marmatite, 1 per cent pyrite and 61 per cent pyrrhotite. The specific gravity of the ore was approximately 4.4. There has been a gradual change in the ore content. The 10 per cent of nonsulphide constituents has increased to between 15 and 20 per cent and all three sulphides have dropped somewhat. Added equipment and changing technique have made possible the treatment of 8000 tons per day of mill feed instead of the 3000 originally handled. SPECIAL FEATURES OF FLOTATION AT SULLIVAN Sullivan flotation differs greatly from customary practice. The very heavy return of lead rougher middling and lead cleaner tailing, totaling at times 125 per cent of the new feed tonnage, has been the subject of much investigation. The practice is still employed.

Jan 1, 1944

By Charles Macdonald

Wrought-iron eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this method of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon: themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

By E. Horton Jones

CONTENTS I Page Introduction ....:......................... 3 Chapter I. Unit Costs. . ...................... 4 Chapter II. Comparative Costs ..................... 20 Chapter III. Composite Costs..................... 32 Chapter IV. Wage Scale....................... 36 Chapter V. Raw Material Prices................. 37 Chapter VI. Description oF Costs ................... 64 Introduction We have endeavored in the following "sheets" to give the unit construction costs derived from 'the building of the Arizona Copper Co.'s new smelter, Clifton, Ariz., starting in February, 1912, and completing February, 1914.l In Chapter I—Unit Costs—are to be found the most elementary total unit costs which the accounts provide for. They are usable in the Clifton district. Here too are found the percentages to be added to an estimate for Engineering and General Expense. In Chapter II—Comparative Costs—these elementary costs have been classified, averaged and reported as labor and material unit costs. In such form the labor unit costs, when properly applied to similar conditions as these under which they were derived, are usable anywhere. The material unit costs are better disregarded for more accurate estimates and replaced by a newly priced bill of material. In Chapter III Composite Costs are given. They are unit costs built up from several elementary units, and likewise units of larger dimensions and simpler application, valuable for

Jan 1, 1915

By AIME AIME

PLANS are now well advanced for the joint meeting of the Institute and over a dozen other engineering societies in Chicago during the week beginning June 26: Engineers' Week at A Century of Progress. All engineers planning to visit the Fair will find it to their advantage to be present at this time so far as the Chicago attractions are concerned, and Eastern members will also have the advantage of special transportation arrangements on June 24 and 25. The tentative program is given at the bottom of the next page. Monday morning, June 26, will be reserved for registration of members and guests and the Woman's Auxiliary at the Stevens Hotel, where special rooms will be provided. A luncheon will also be served there, and in the afternoon, a technical session on nonmetallics. Instead of having the big family dinner that evening at the Stevens, as at first proposed, the local committee has planned to have it at the Fair Grounds, where special facilities have been arranged. A meeting of the Board of Directors and a few invited guests will precede the dinner. All members and guests are likely to be interested in visiting the Museum of Science and Industry, so that will be the sole event on the program for Tuesday morning, June 27. The big attraction there at present is the model coal mine, the first operative coal mine ever built for exhibit purposes. It is based on the Deutsches Museum mine at Munich, but goes far beyond that in realism, and takes the visitor on an extended tour underground. It shows him in half an hour more types of modern mining machinery and coal geology than he would be likely to see in a week's underground study in the coal fields. The Institute members will be the first group to go through this mine.

Jan 1, 1933

By E. D. Gardner

IN 1947 the metal-mining industry . passed through a year of readjustment; catching up on development work has caused production to suffer. Skilled labor has been short in most mining districts, notwithstanding the highest wage rate paid in the history of the industry. The trend has continued toward increased mechanization and refinements in practices and methods to increase the tons produced per man-shift. Improvements in procedures, however, have not kept pace with rising labor rates; and, in general, labor costs per ton mined have steadily increased since the war years. Prices of base metals have been the highest in a generation, but most producing companies can afford to pay the high wages. Capital expenditures have been approved for improvements to increase the output per man, both to reduce unit labor costs and to increase output. Surveys indicate a continuing

Jan 1, 1948

By M. V. Lowry

This paper outlines the economic considerations that led to the recent installation of a thickener at St. Joseph LeadCo.'s Balmat, N.Y. mill. To incorporate storage of concentrates, they decided upon a single, unusually deep tank to be used for both storage and thickening. The abnormally high rake lift required was achieved by the novel feature of having the entire drive platform raise and lower. Initial operating problems are described along with the satisfactory solutions. Total costs for concentrate handling before and after installation of the storage thickeners are compared. In Northern New York State, the St. Joseph Lead Co. conducts a 2100 tpd zinc mining and milling operation at its Balmat Plant. Conventional crushing, grinding, and flotation is used to produce a zinc concentrate. For 32 years, from 1930 through 1962, the plant operated with the concentrates going directly from flotation to the filtering, drying, and loading facilities. All of the concentrate handling equipment, therefore, had to operate 24 hrs per day. It also had to accommodate wide fluctuations in tonnage, due to variations in the grade of ore. Many problems were thereby encountered in filtering and drying, but it was never concluded that the cost could be justified for installing a conventional, large diameter thickener. Finally, in 1963, they installed an unconventional thickener that is unusual in several respects. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes. After three years of operating this unique storage-thickener, the conclusion is that a correct choice was made from several alternative schemes for storing concentrates. The various considerations involved in the final selection will here be analyzed, and the design features and installation details will be de- scribed. Operating problems and modifications made to the equipment will next be considered, and finally the effects upon filtering, drying, and loading will be reported. SELECTION CONSIDERATIONS Even without a thickener, concentrate handling had become reasonably efficient at the Balmat Mill by the year 1962. A tonnage that varied between 6 and 25 tph was being handled fairly satisfactorily. The filter cake moisture of 8%% seemed quite respectable, except that two large filters were usually in service. Three filters often had to be operated in order to prevent excessive filter overflow with consequent loss of values. This situation occurred when zinc concentrates from flotation exceeded 20 tph and when filter cloth blinding developed. Over the years, numerous small improvements had been effected, such as: selection of a filter cloth with better flow characteristics; addition of flocculant to the filter feed; and, in 1953, the smallest of three drum filters was replaced by a five disc, 8' 10" diam filter with a bottom agitator and snap blow. As another example of fairly efficient operation, the oil-fired dryer was doing a seemingly satisfactory job of further reducing the moisture content to an average of 3%. However, there were often considerable dust losses when the tonnage suddenly dropped off to 6 tph. At high tonnage rates, the resulting high moistures of 4% and 5% caused difficulties due to concentrates sticking and freezing in chutes leading to the box car loaders. (Drying of concentrates is justified because of the high freight rate for the long shipping distance to the company owned smelter at Josephtown, Pa. near Pittsburgh.) It was long realized that installation of a thickener would permit the subsequent steps of concentrate handling to proceed more smoothly and would alleviate the problems existing in the filtering, drying, and loading operations. It was also realized that even a slightly lower filter cake moisture could mean considerable savings in fuel oil. However, all these factors were never quite sufficient to warrant the expense of a thickener until three more considerations were added to the picture. First, the advent of flocculants meant that a thickener of relatively small area could now be considered. Secondly, a complete renovation of the zinc flotation circuit was made between 1957 and 1961. The

Jan 1, 1967

By C. H. Li, R. J. Stokes, T. L. Johnson

The effect of alumina particles on the nucleation and growth of cracks through a silver- chloride matrzx has been investigated. It has been found possible to promote fibrous cracking in dispersion-strengthened silver, chloride under notch-impact conditions at temperatures at which silver chloride alone cleaves brittlely The modification) of fracture beIzavzor is thought to be due to the relaxation of hydrostatrc stress beneath a notch by the nucleation of cavities near alumina particles. In recent years, composite or dispersion-strengthened materials have been studied primarily to understand their high resistance to plastic flow particularly at elevated temperatures. Dislocation models have been developed with which it is possible to deduce with fair success the effects of interparticle distance, particle size, temperature, upon yielding and creep behavior.l-4 Much less attention has been paid to the fracture behavior of these materials (with the notable exception of common structural steels) and little is known experimentally about the manner in which inclusions affect the nucleation and growth of cracks through a matrix. Nevertheless a beginning has been made in connection with fibrous cracking in ductile matrices where inclusions appear to play an essential ro1e.5-7 During the severe localized plastic deformation which accompanies necking in a tensile test, cavities are believed to develop at inclusions; these cavities subsequently grow and coalesce by plastic flow until separation is complete. It is of interest to consider whether inclusions can affect fracture behavior under loading conditions which restrict the plasticity of the matrix itself (for example, cleavage under conditions of a high imposed strain rate at low temperatures). It is particularly interesting to study these effects in a solid which shows a spectrum of behavior ranging from fully ductile to semi-brittle behavior. Such a solid is silver chloride whose mechanical behavior depends sensitively upon temperature and strain rate.'," The present paper is concerned with a study of the influence of inclusions (in the form of alumina particles) on the fracture behavior of silver chloride loaded uniaxially at low strain rates at room temper- ature and also under notch impact conditions over a wide range of temperature. In particular, it will be shown that the alumina particles can exert a startling effect on the ductile-brittle transition temperature of notched silver chloride and that the magnitude and nature of the effect depends upon both the quantity of alumina and the shape of the alumina particles. 1. EXPERIMENTAL PROCEDURE 1.1 Materials Used. Silver chloride powder of analytical reagent (AR) quality having an average particle size 6 was supplied by the Mallinckrodt Chemical Works (st. Louis, MO.). Acid washed 900 mesh alumina powder, designated A38-900, was supplied by the Norton Co. (Cambridge, Mass.). This powder was added to silver chloride in two forms: a) the as-received condition in which the individual particles were of random irregular shape; their statistical average size was 7; b) in a condition in which each particle was spherically shaped by a fusion technique. In this case, the statistical average particle size determined with the optical microscope was approximately the same (about 5p) but electron micrographic evidence indicated that many ultra fine particles were present in the spheroidized powder. 1.2 Preparation of Composite Materials. Silver chloride-alumina composites containing 2.5, 5, and 15 pct by volume of alumina were produced by the extrusion of mechanically mixed powders blended in a ball mill for 24 hr at room temperature. The mixtures were compacted at 50,000 psi at room temperature in the form of billets 3/4 in. in diameter and 1 in. long which were then extruded with a 16:l reduction ratio at 370°C through a radius-type steel die having a 5 deg lead-in angle. An extrusion temperature of 370°C was selected to ensure that all composites had sufficient plasticity to be extruded. Apart from this general requirement, the choice was arbitrary. 1.3 Microstructure of Composites. Attempts were made to check the distribution of alumina metallo-graphically by polishing transverse and longitudinal sections of the extruded rod. Specimens were wet-ground to 600 emery paper and lapped successively with 5 and 0.25-p grades of diamond paste. They were etched for 10 sec in 10 pct sodium thiosulfate solution and lightly polished in concentrated ammonium hydroxide. The most effective way to render the alumina particles and grain boundaries visible was to radiate the surface with intense white light to decorate the grain boundaries and the particle-matrix interfaces photolytically.

Jan 1, 1962

By R. B. Mears, G. F. Sagar, R. H. Brown

There are well recognized procedures for determining the various tensile, fatigue, and other mechanical properties of the common structural materials. This makes it possible for engineers to design structures of various materials which have adequate initial strength to stand the stresses to which they are subjected in service. There is also considerable general information about protective measures suitable for protecting the usual structural materials from the effects of ordinary environments. However, often insufficient quantitative information is available on the combined effects of stress and corrosion to permit the designer satisfactorily to appraise the structure from the stress-corrosion standpoint. This situation is further complicated by the fact that the stresses causing stress¬corrosion failures are usually not the design stresses but rather the residual forming and assembly stresses which are generally of unknown magnitudes. Thus, tests which will rapidly evaluate the susceptibility of materials to stress-cor¬rosion failures are extremely useful. Of particular value are tests which can be applied to built-up structures as well as to simple specimens, since, as mentioned above, residual stresses often are caused by fabricating procedures and assembly operations. The present paper contains

Jan 1, 1945

By K. E. Gray, M. S. Seth

Equations of elasticity for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure were formulated. Using an analogy between thermal and porous body stresses, it was shown that the solution for a transversely isotropic porous body may be obtained by incorporating body forces and the stresses due to a boundary load into the corresponding solution for the thermal stress problem. Equations of elasticity ad the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant pressure or a constant rate of flow is maintained at the wellbore. The vertical and tangential displacements are zero from the conditions of the problem. A numerical analysis was made of the solutions obtained by using a digital computer to determine the relative influence of each system variable. Considering rock as a porous body with internal fluid pressure generally gives results significantly different than considering the rock to be nonporous; the directional character of rocks leads to significant differences as compared to results based upon the common assumption of isotropy. Stress gradients are high near the wellbore but die out away from the well. Radial stresses are compressive or neutral, whereas tangential stresses are tensile, neutral or compressive, depending upon the boundary conditions and physical properties of the system Vertical stresses are compressive for an unbounded system. For constant wellbore injection rate, the vertical stress is proportional to the rate of fluid injection and decreases with time, whereas the radial and tangential stresses increase with time. At a given location, the radial displacement generally is very dependent upon time. INTRODUCTION A realistic appraisal of the state of stress in subsurface rock formations would be of considerable interest and use to the petroleum industry. For example, knowing the state of stress in proximity to a wellbore would be of fundamental importance in designing a fracturing operation or, more important, of clearly understanding the conditions necessary to produce rock failure of desired dimensions and geometry. Understanding conditions necessary for rock failure at the wellbore would also be of utility in a preventive sense. For example, borehole stability is an important consideration for many rock formations, and knowledge of the stress state at and near the wellbore under conditions of substantial pressure gradient due to fluid flow would be of great value. When fluid flows through a porous body which is initially at some uniform stress level, the following forces generate stresses at any point in the body. (1) Forces due to nonuniform pressure distribution. With increasing pressure the elements of a body are compressed. Such compression cannot proceed freely in a continuum when the pressure is not uniform throughout, and thus, stresses due to flow of fluid are set up. (2) Pore fluid pressure. This gives rise to normal stresses whose value at any point is the product of areal porosity and the fluid pressure. Although the fluid exerts uniform pressure, the stresses it creates in an anisotropic body may not be the same in all directions since the areal porosity in an anisotropic porous body is a direction-dependent quantity. This consideration leads to the concept of directional porosity. (3) Body Forces. The flow of the moving fluid imparts a force to the rock matrix, the magnitude of which depends upon the pressure

Jan 1, 1969

By A. G. Metcalfe, A. Siede

The hardening of annealed copper during fatigue testing appears to be independent of the applied stress and to occur largely within the first 4000 cycles. Copper hardened by fatigue is more resistant to annealing than copper hardened by static means, and softens by a multistage process. Creep studies at 300°C show that copper hardened by fatigue also has greater resistance to creep than statically hardened copper. Some theoretical explanations are discussed. RECENT interest in the behavior of metals subjected to fatigue stems from observations of phenomena which could not be explained by current theories of the structure of metals. In 1953 Bullen et al.l showed that the hardening caused by fatigue at low stresses did not cause severe bending of the lattice as did hardening by static methods. This was later confirmed by Wood, 'and Broom and Ham.3 Clarebrough et al4 showed that as the stress level used in fatigue hardening was increased, bending of the lattice was introduced, eventually approaching that of metals deformed by conventional cold-working methods. The type of hardening introduced by fatigue has other interesting characteristics. Kemsley5 showed that copper fractured by fatigue at low stresses resisted annealing as compared to copper hardened an equal amount by static means. The work of Clarebrough etal, shows that the manner of energy release during annealing differs for fatigue-hardened and statically hardened metal in both magnitude and temperature range of release. In addition to hardening of the lattice, fatigue has been shown to cause softening in materials previously hardened by static methods,5 and also in age-hardened alloys.7 The superposition of a small fatigue stress on the static loading of high-temperature alloys has been shown to increase their resistance to creep.' The present work was an attempt to determine the relationship between fatigue hardening, resistance to annealing, and the creep properties of pure copper. EXPERIMENTAL PROGRAM The program described here was designed to answer three questions: 1) Can stress-cycle combinations well below the failure values give significant increases in hardness? 2) Does hardening, under different stress-cycle combinations, give increase resistance to annealing? And if so— 3) Does superior resistance to annealing confer superior creep properties over statically hardened material? Three-quarter hard OFHC copper was annealed in vacuo at 550°C for 1 hr to produce a strain-free material having a fine grain size and uniform hardness. (The standard deviation of the mean hardness of the annealed samples was less than + 1.9 Dpn). Annealing was performed after machining the fatigue specimens so as to avoid work-hardened surfaces. Jigs were used to avoid distortion. The fatigue properties of the annealed copper were determined using an accurately aligned Baldwin-Sonntag SF1-U machine operating at 1800 cycles per min. This limited the minimum number of cycles which could be examined to about 4000 stress reversals. Since failure resulted in specimen damage, hardness increase with number of cycles was measured by testing specimens fatigued to different fractions of the failure values. The results are shown in Fig. 1, and are superimposed on the S-N curve of the copper in Fig. 2. The resistance to annealing of fatigue-hardened material was compared to that of material hardened by uniaxial tensile straining. Specimens hardened to equal values by both methods were progressively annealed for 1 hr at temperature in vacuo. After each annealing treatment the hardness was measured using a Leitz Durimet hardness tester with a 500-g load. At least five tests were made for each hardness determination. The standard deviation for individual specimens varied from 0.26 to 1.48 hardness points. The results are shown in Figs. 3 to 5. The discontinuous nature of the annealing process has been brought out by drawing idealized curves through the data points. This can be justified by the consistency of the results as well as by general agreement with results of Kemsley.5 The creep resistance of fatigue-hardened and

Jan 1, 1960

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after it has been pulverized to pigmentary size. The current world production of iron oxide pig¬ments is estimated by the author to be between 450,000 and 550,000 tons based on 1969 data. The fact that highly colored natural deposits of iron ore are found throughout the world ac¬counts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments pro¬duced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970). Nomenclature With the increasing importance of the syn¬thetic iron oxides it is necessary to make a distinction between the natural or mineral pig¬ments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a com¬mercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pig¬ments. Natural pigment ore sources are se¬lected for their special physical-chemical prop¬erties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pig¬mentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1975

Abbey, Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St.. New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Zac., Mexico. '28 Abbott, Argyle Campbell, Dev. Dept., E. I. du Pont de Nemours & Co., Wilmington, Del. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg.. Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co., Jenkins, Ky. '16 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh. Pa. '28 Abeel, Leo M., Research Engr., Sullivan Concentrator Chapman Camp, B. C., Canada. '31

Jan 1, 1932