Search Documents

By W. J. Joslin

The frontal-advance equation can determine how the fluid withdrawal rate and subsurface operating pressure influence oil recovery from pressure-maintained reservoirs having characteristics favorable for efficient vertical segregation. For effective vertical segregation in formations having low dip angles, the requirements are: thick, massive sands, low viscosity oil and high vertical permeability with few discontinuous shale members. This approach has been successfully applied to the LL-370, which is a massive Eocene sandstone reservoir containing crude with an average gravity of 26" APT, a dip of only 3" and vertical permeability of ½ darcy. The average gas cap saturation was calculated for various rates of vertical gas-oil contact movement corresponding to a wide range of reservoir producing rates. This method also evaluated the effect of different pressure maintenance levels on oil recovery. Applicability of this procedure for calculating the present oil saturation in the LL-370 gas cap has been substantiated from field performance, where the oil saturation was computed by comparing oil recovery with the gas cap volume vacated. INTRODUCTION During the natural depletion history of the LL-370 reservoir, located in Lake Maracaibo, Venezuela, excellent vertical segregation resulted in the formation of a thin gas zone over a substantial portion of the oil-productive area. Subsequently, gas injection forced this thin gas-saturated zone slowly downward, reducing the oil saturation in the gas cap to a low value. The oil recovery has been raised considerably above earlier predictions where vertical segregation effects were under-estimated. In order to determine the maximum efficient producing rate and optimum operating pressure for this reservoir, a vertical gas frontal-advance analysis has been made through application of the fractional flow equation. LL-370 RESERVOIR CHARACTERISTICS The reservoir consists of a truncated monocline of massive. highly-permeable Eocene sandstone, called the B-b formation, covering an area of more than 13,500 acres. The original oil in place was 2.17 billion STB. Internal non-sealing faults subdivide the structure into four blocks called the B-6-x.6, 10, 11 and 13, which are effectively bounded by major faulting on the flanks, an unconformity updip to the west, and an immobile aquifer to the southeast. The producing formation occurs at an average depth of 5,250 ft subsea and has a closure of more than 1,500 ft. A typical producing section has a net oil sand thickness of 170 ft. Scattered throughout the section are a few randomly-positioned shale lenses which increase in thickness and areal extent downdip. The reservoir rock and fluid properties vary with depth. The permeability and produced oil gravity are 1600 md and 28" API at the top, compared to 300 md and 18° API at the water-oil contact. The productivity of updip wells is, therefore, much higher than the reservoir average. The reservoir oil was originally saturated at the crest, grading to a slight degree of undersaturation at the water-oil contact. There was no original gas cap; and material balance and the field performance indicate no water influx. Except for the northern B-6-x.6 block, the fluid and rock properties have already been published.' Average LL-370 reservoir properties are shown in Table 1. RESERVOIR PERFORMANCE UNDER NATURAL DEPLETION Fig. 1 shows production performance from 1939 to date. Early development was gradual, with 30 wells pro-

Jan 1, 1965

PROF RICHARD ÅKERMAN Stockholm, Sweden ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France PROF HANS HOEFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France M FLORIS OSMOND Paris, France JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia CHARLES D WALCOT Washingtion D.C.

Jan 1, 1910

By Read Winterburn

This study of the relationship of the accumulation and drainage of oil to the structural conditions in the Wilmington oil field is presented with the hope that the data contained herein will aid in efficient exploita-tion of other fields where similar conditions exist. It is also probable that the conditions observed in this field will enable accurate comparisons of various well-spacing programs as to efficiency of production and ultimate recovery. Formations in Wilmington Field Age Formation Thickness Lithology and Remarks Quaternary and Pleistocene. San Pedro 1000 t Fresh-water sands, gravels and clays Pliocene Upper Pico 800 t Alternating sands and silt- Stones Pliocene Middle Pico 0-200 ± Sands and siltstones Unconformity Pliocene Repetto 875-1150 Gray and green shales, silt-stones and sands at top grading to interbedded gray-ish brown shales and fine-grained sands toward bot-tom Miocene Puente 4100± Hard brown shales and sands. Sands are fine and uncon-solidated at top, becoming firmer and coarser grained toward bottom. Top por-tion contains layers of lam-inated diatomaceous shale Unconformity Schist The data included herein are not complete as to all areas and zones, being confined mostly to the area south of Anaheim Street. The sections presented are illustrative of edge-water conditions in the Terminal zone and Tar zone, but have not been extended down the structure far enough

Jan 1, 1940

By L. F. Marek, G. W. King, A. Bogrow

THE purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction Of FeO to Fe. Unless the gas has a CO/CO2 ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available) the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity f the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"-i.e., the efficiency of conversion of the "available" CO supplied-is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size Of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1947

By AIME AIME

. COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS : NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Apr 1, 1910

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910.) VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.) W. C. RALSTON..: SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.)

Jun 1, 1909

By AIME AIME

COUNCIL.* PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1910.) VICE-PRESIDENTS OF THE COUNCIL. J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, MICH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.) W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN. (Term expires February, 1911.)

Mar 1, 1909

PRESIDENT OF THE COUNCIL. D. W. BRUNTON DENVER, COLO. (Term expires February, 1911.) VICE-PRESIDENTS OF THE COUNCIL. W. C. RALSTON SAN FRANCISCO, CAL. W. L. SAUNDERS NEW YORK, N. Y. H. V. WINCHELL ST. PAUL, MINN.¬ (Term expires February, 1911.) BENJAMIN B. LAWRENCE NEW YORK, N. Y. JOSEPH W. RICHARDS SOUTH BETHLEHEM, PA. ALBERT SAUVEUR CAMBRIDGE, MASS. (Term expires February, 1912.)

Jan 1, 1917

By Paul M. Tyler

FOR the same reason that water is not missed until the well runs dry, the roles of many industrial minerals in wartime are often overlooked. In contrast to the growing shortages of many metals, our supplies of most nonmetallic minerals are limited only by our machinery for taking them from the ground and by our processing facilities. With few exceptions, the demand for increased supplies has been met without fanfare or delay. Only Brazilian quartz crystals, certain kinds of mica, and, latterly, industrial diamonds are on the so-called strategic list, although asbestos, beryl, corundum, cryolite, fluorspar, crucible-grade graphite, ilmenite, iodine, kyanite, monazite, nitrates, rutile, and zircon have caused more concern among those responsible for procurement and are included in our preclusive buying programs. Such specialties are needed urgently, but they are far less important in the over-all picture than the more abundant minerals.

Jan 1, 1942

By R. B. G. Yeo

Pronounced isothermal martensite formation at room temperature was measured dilatometrically in a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pctAl, 2.58 pct Ti and 0.25 pct Cb. It is shown that martensite will form isothermally if stabilization of the austenite-martensite transformation is eliminated by removal of carbon. The decarburization of two iron-nickel alloys allows isothermal transformation to martensite to occur at temperatures above their athermal Ms temperatures. In an Fe-22.4 pct Ni alloy, at the 0.008 pct C level, the Ms temperature during air cooling is 85°F higher than that during- water quenching-. At the 0.15 pct C level this difference is reduced to only 5°F. The introduction of carbon causes stabilization during air cooling which lowers the Ms temperature virtually to the same level as determined during mate?. quenching. Thus in the 0.15 pct C alloy, the Ms temperature is almost independent of cooling rate. It is suggested that rival theories of martensite formation should be reexamined in alloys of sufficiently low carbon and nitrogen content to eliminate the complication of stabilization. The Ms temperature of a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pct Al, 1.58 pct Ti and 0.15 pct Cb, solution treated at 1500°F and air cooled as 1/8-in. diam specimens, was found to be 57 °F. 1 However, when held for several hours at room temperature the steel hardened slightly and became appreciably ferromagnetic. Isothermal transformation to martensite was first revealed by Kurdjumov and Maksimova2 in an iron-base alloy containing 0.6 pct C, 6.0 pct Mn and 2 pct Cu. Most of the other studies of isothermal martensite have also been confined to highly alloyed steels which transform at subzero temperatures; for instance, DasGupta and Lement, 3 Cech and Hollomon, 4 Machlin and Cohen,5 Shih, Averbach, and Cohen.6 Averbach and cohen7 noted a rapidly decaying volume increase at room temperature in a steel containing 1 pct C, 1.5 pct Cr and 0.2 pct V. cina8 and Marshall, Perry, and Harpster9 have described the isothermal transformation to martensite at room and subzero temperature in stainless steels. Kurdjumov10 has recently reviewed the subject, noting that the isothermal formation of martensite can be observed only in the temperature range somewhat below Ms or below -50°C. The isothermal formation of martensite may be characterized as follows: 1) It occurs in steels of widely different compositions, the main prerequisite being a low transformation temperature. 2) The transformation occurs by the formation of new plates and not by the growth of old ones. 3) The isothermal transformation is suppresed by stabilization during slow cooling or holding at temperatures near room temperature. However, the factors governing this mode of transformation are still not fully understood. The formation of martensite isothermally suggests an activated process. The early theories of martensite formation did, in fact, utilize classical nucleation concepts. Kurdjumov 11 first proposed the presence of thermally activated nuclei of different sizes and compositions which would grow if they reached critical size during cooling. This treatment was enlarged and developed quantitatively by Fisher, Holloman, and Turnbull12,13 and was later reviewed by the latter two authors.14 Fisher15 associates Ms with a nucleation rate of one per cc per sec. At slightly higher temperatures the nucleation rate is so low that isothermal formation of martensite is not observed in reasonable times. At slightly lower temperatures the nucleation rate is so high that it could not be suppressed by rapid cooling. By judicious use of parameters Fisher 16 was able to obtain good agreement between classical nucleation theory and the incubation times of martensite formation.4 However the application of these principles to martensite formation in iron-nickel alloys15 predicts that an alloy containing about 30 pct (31 at. pet) Ni would not transform. The presence of an Ms temperature at -223° C in an alloy containing 34.1 pct (33 at. pct) Ni led Kaufman and cohen17 to reject the hypothesis of homogeneous nucleation in favor of the reaction path theory originally proposed by Cohen, Machlin and Paranjpe.18 This theory conveniently explains the formation of martensite athermally but becomes labored when dealing with isothermal formation. Kaufman and cohen19 did explain the isothermal activation of embryos by assuming it to be a result of the expansion of their boundary dislocation loops but this treatment predicts an upper temperature limit of isothermal martensite formation.

Jan 1, 1962

By J. L. Moriarty, Irving Johnson, H. M. Feder

The crystallization of ternary alloys has been studied as a coprecipitation phenomenon by measuring the substitutional carrying of trace metals with CeCd11 precipitating from liquid cadmium. The Doerner-Hoskins logarithmic distribution law has been found to apply in all cases; the coprecipitation coefficients obtained were: 1.48 (La), 1.06 (Th), 0.63 (Pr), 0.24 (Gd), 0.17 (Sm), 0.13 (U), 0.10 (Er), 0.09 (Sr). Li, Na, K, Ba, Y, Sc, and Zr were not measurably carried. It has been observed that coprecipitation was most extensive for those tracers which form with cadmium an intermetallic compmdnd isostructural with CeCd11 or closely related thereto. For these tracers an inverse relation between Solubility in cadmium and coprecipitation coefficient was noted. THE partition of impurities between the liquid and solid phases of a metal or a congruently melting intermetallic compound has been extensively studied by the methods of zone melting.' However, when the composition of a liquid alloy and of the solid phase crystallizing from it differ grossly, partition of an impurity cannot be investigated in this manner. Partition of the impurity under equilibrium conditions may be studied by investigation of the appropriate phase diagram and partition under nonequi-librium conditions may be studied by observation of coring in the solidified alloys.2 The nonequilibrium case is of special interest in metallurgical practice because many complex alloys are cooled too rapidly to permit the uniform diffusion of impurities throughout the crystallizing phase(s). With this in mind, the present study was undertaken to obtain quantitative data on the phenomenon of coprecipitation via substitutional solid solution in certain metallic systems. It will be noticed that rather than adopting metallurgical ter- minology we have chosen to refer to the partition of impurities during alloy crystallization as coprecipitation.3 In the terminology of coprecipitation the impurity is referred to as the tracer and the precipitating phase as the carrier. From aqueous solution, coprecipitation may occur as a result of adsorption on the surface of the carrier, by occlusion of the liquid within the crystals, or by solid solution of the tracer in the carrier. By slow cooling of liquid metallic solutions it is relatively easy to form large, regular crystals of the carrier; the effects of adsorption and occlusion may be minimized and the influence of substitutional solid-solution formation may be made to predominate. Previous studies of the crystallization of some intermetallic compounds4 and of copper, silver, and gold5 have shown that the coprecipitation or partition behavior of trace metals is entirely analogous to that observed in aqueous systems when ionic substitution occurs, e.g., coprecipitation of Ra++ with BaSo4. The precipitation of CeCd11 from liquid cadmium was chosen for study. This choice was influenced by the following consideration. If the relative atomic sizes of the tracer atom and the atom for which it substitutes determine the tendency to coprecipi-tate, then a lattice having a substitutional site of well-defined size would be desirable. In CeCd116 (structure type cubic BaHg117) the cerium atom is completely surrounded by a cage of twelve nearly equidistant cadmium atoms. Thus, atoms much larger or much smaller than cerium should be poorly accommodated in this cage. The choice of a lanthanide central atom allowed the testing of the size hypothesis with a number of lanthanide tracers which differed in size but not in valence or electro-negativity. EXPERIMENTAL The general technique of this investigation was to prepare a slightly undersaturated solution of carrier in liquid cadmium to which a tracer was added. The concentration of tracer was always so low that saturation over the entire temperature range investigated was never exceeded. The solution was cooled in a stepwise fashion. After each step a por-

Jan 1, 1964

By AIME AIME

ON May 5, the Washington, D. C., Section, A.I.M.E., devoted its meeting to the many-sided and perplexing question of mineral stock-piling for peace. Opening the symposium, Harry J. Wolf, of the War Production Board, outlined the problem under six heads: (1) Technical. Mechanical, chemical, or metallurgical importance of specified materials, emergencies that might arise, relative scarcity, and critical value of stock piles during emergencies. (2) Economic. Cost to Government, influence of Government stocks on commercial relationships and markets, effect of availability of items as a con¬structive influence on industry, Administration policies now and during postwar period. (3) Legislative. Need for immediate legislative action, need for legislation on postwar conditions as well as on current requirements, a constructive basic policy to prevent political manipulation. (4) Military. Consideration of re¬quirements and supplies bearing on national safety and needed for manufacture of equipment, and adequate reserves of scarce materials for research or experimentation by military agencies. (5) International. Interests of the United Nations in contradistinction to those of the United States; effects of nonisolation policy on nature, location, and administration of stock piles. (6) Negative stock-piling. Question of United Nations' legislation to prevent stock-piling by Axis nations after the war and who shall purchase stock-pile materials and during what periods.

Jan 1, 1943

By Stephen G. Wright

Jan 1, 1985

By Kurt Kennedy

A method is described by which three elements can be condensed simirltaneously on a common substrate in such a way that the composition varies with position on the substrate. Almost all possible combinations of three solid elements can be formed in a single evaporation. The three elements are heated by magnetically deflected electron beams. The alloys and cornpounds formed by this method generally correspond to those trade by other methods; however, many exceptions exist. Simple symmetric crystallographic phases tend to form in preference to more complex phases. The Nb-Sn. Cr-Fe-Nt, and other systems of alloys made by this method will be discussed. Phases that form very slowly, such as the o phase in Cr-Fe alloys, may be formed rapidly by this method when certain substrate temperatures are used. STUDYING all the mixtures and compounds of two or more elements by the preparation of individual samples forces the investigator to make sampling sufficiently close together so that the properties of the intermediate compositions can be inferred. A completely unknown system will require a dis c our aging ly large number of preparations in order to fully know all its properties. For the purpose of expediting this type of investigation, methods have been devised to prepare samples that have a continuous variation in composition over some predefined area. The code-position of two elements onto suitable substrates has been used to produce alloys or compounds that have variable compositions depending on their positions on the substrates Composition gradients have been formed by depositing a wedge-shaped layer of one element and then depositing a second wedge-shaped layer on top of it such that the total film thickness is kept constant. Concentration equilibrium perpendicular to the surface is then established by annealing.4 This paper describes a method for the simultaneous condensation of three volatile components on a substrate such that there is a regular variation of composition with position on the substrate. The arrangement of the evaporation sources and the substrate is shown schematically in Fig. 1. Materials to be evaporated are placed in three water-cooled crucibles located at the corners of a 10-in. equilateral triangle. Electron beams from cathodes located below the crucibles are bent 180 deg by magnetic fields and focused on the material to be evaporated. The cathodes are connected in parallel to a constant-current 12-kv power supply. The distribution of emission current from each cathode is controlled by filament temperature. When materials that sublime are to be evaporated, the electron beam is deflected by an auxiliary ac magnetic field so that the beam moves over the surface of the evaporating material rather than digging a hole in one spot. The substrate is a 10-in. triangle of 2-mil stainless steel or molybdenum which is stretched against a slightly curved heat sink by a frame as shown in Fig. 2. This frame and heat sink are located so that each corner is directly above an evaporation source. The heat sink has three radiant heaters at each corner that can be separately controlled permitting the

Jan 1, 1967

By John A. Church

Jan 1, 1903

The following list comprises the names of those persons who became members during the period May 10, 1919, to June 10, 1919. ALAYZA, CARLOS Box 850, Lima, Peru, S. A. BALLARD, P. A Surveyor, Midwest Refin. Co., Custer, So. Dakota. BARNEBL, A. J., JR.... Mech. Eng., The Dorr Co., 101 Park Ave., New York, N. Y. BILLINGS, GOODSELL Platteville, Wis. BRONSON, C. B., Mech. & Met. Engr., New York Central Lines, Room 1520, Grand Central Terminal, New York, N. Y. BUNCE, E. H Met., The New. Jersey Zinc Co., Palmerton, Pa. CHARLTON, D. E. A., Editorial Staff, Engrg. & Mm. Journals 10th Ave. & 36th St., New York, N. Y. DAVIS, JOHN N., Supt. of Mills, Engels Copper Min. Co., Engelmine, Plumas Co., Cal. DUKES, GLENN H., Chief Engr., The Sunday Creek Coal Co.,1001 Outlook Bldg., Columbus, Ohio. ERICKSON, ARTHUR .... Engr., United Smelt., Refin. & Min. Co., Mldvale, Utah. FLYNN, A. E Supt., Rand Consolidated Mines, Ltd., Goudreau, Ont., Canada. HIBBARD, WALTER R 63 Ashley St., Bridgeport, Conn. HOBSBAWN, I. BERKWOOD, Cons. Tech. Chem., Messrs. Gibbs. & Co., Valparaiso, Chile, S. A.

Jan 7, 1919

By Jorge Munoz Reyes, Guillermo

The new entity, Yacimientos Petroliferos Fiscales Bolivianos, created in 1936 for the development and exploitation of all petroliferous zones of Bolivia, including those formerly belonging to the Standard Oil Co., is doing its utmost to bring about rapid development and by this means to create a new source of revenue for the State. With this in view, Y.P.F.B. has opened a new field in the Samaipata region, on the main road between Cochabamba and Santa Cruz. Installation of machinery has begun for the drilling of several wells on the five anticlines that occur in this region. Work has also begun in the Saipuru field, on the Santa Cruz-Charagua highway, which was discovered by the Standard Oil and temporarily abandoned. In this new field, a topping plant will be installed, to supply gasoline and kerosene to Santa Cruz. Explorations are also being made on the neighboring structures of Saipuru. At the end of 1937, the committee that is to study the region of the Chapare in the northeastern part of Cochabamba, was organized. The structures were studied 10 years ago by Kirtley Mather and other geologists. It is hoped that by March 1938 this camp will begin work, as this zone gives promise of being valuable. Development The capacity of the refinery at Camiri has been enlarged in order that it may supply all the needs of that region. In order that the supply of crude may be adequate, several wells that had been almost abandoned by the Standard Oil are being cleaned out. New wells have been located at this camp following the principal anticlinal structure, and during the first half of the year 1938 several wells will be drilled. The same program is being followed in Sanandita but on a greater scale, as the nearness of this district to the Argentine border, which is the best market for the Bolivian petroleum of the south, allows immediate sale of the petroleum. Possibly a new refinery will be installed at this camp, as the one now in existence is only a rudimentary distillery. At the Bermejo camp, which is farther south, intensive work is being done to bring the wells into production. The Standard Oil produced limited quantities several years ago, but since 1927 the wells of this dis-

Jan 1, 1938

By AIME AIME

THE following Officers, Directors, and guests were present: Herbert Hoover, A. R. Ledoux, Henry S. Drinker, Edwin Ludlow, Samuel A. Taylor, Charles F: Rand, William M. Corse, Arthur S.. Dwight, Glen H. Clevenger, L. W. Francis, F. G. Cottrell, Bradley Stoughton, Percy E. Barbour, E. P. Mathewson, Dorsey A. Lyon, Archibald Douglas, A. D. Flinn, RobertLinton, James F. Kemp, William Y. Westervelt, J. W. Richards, W. L. Saunders, George Otis Smith, Thomas T. Read, J..C. Murray, Ralph Arnold. A Committee on Mine Equipment was appointed composed as follows: Graham Bright, chairman, William Kelly, Howard N. Eavenson, R. E. Hobart, and S. P. Rumsey. B. D. Saklatwalla was added to the Committee on Miscellaneous Metals and W. Spencer Hutchinson was added to the Committee on Mining Geology. A revised budget for 1921 was approved. A petition duly signed to amend Section 1., of Article III of the Constitution, increasing the initiation fees from ten dollars to twenty dollars, was approved by the Board.

Jan 1, 1920

By Richard E. Chism

Some years ago, when I was seeking an illusive fortune and gaining a precarious existence in the primeval forests of Brazil, there penetrated, even to my headquarters in that far-off land, the story of a new-found mining district, where mountain peaks were ribbed with silver, and valleys teemed with virgin gold. Such were the stories that caused hundreds of men to seek their fortune in Sierra Mojada, and to return heaping curses, loud and deep, upon the vivid imaginations that had evolved the glittering fiction. Nevertheless, the rumors had some foundation of truth. The ribs of silver exist, if not the placers of gold; and a flourishing town, of some three thousand people, with two leading mining companies and several smaller ones, in operation, represents what was permanent in the excitement of 1879. Geographical Situation. The town of Sierra Mojada is situated in the State of Coahuila, Republic of Mexico, in latitude 27' 24' N., and longitude 26' 40' W. of Washington, 4' 36' W. of the City of Mexico, and 103' 43' TV. of Greenwich. It lies about 70 miles, in an air-line, N. E. of Escalon station, on the Mexican Central Railroad; but by the present wagon-road, which makes a long detour to turn the mountain range, the distance to the station is about 105 miles. The nearest towns are Huajuquilla, in the State of Chihuahua, about 125 miles due west, and Cuatro Cienegas, in the State of Coahuila, 112 miles to the eastward. Between these points and the town of Sierra Mojada, and to the north of this town, the country is an immense desert, entirely uncultivated, almost uninhabited, and very little known. This

Jan 1, 1887

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U3O8 /t) (0.80 lb U3O8) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling. Based largely on what we had learned from Western Nuclear's experience, we undertook a program involving a laboratory study to determine the characteristics of the mineral stockpiles, as related to heap leaching, and to conduct a pilot heap leach adjoining our Gas Hill mill. Basically the pilot heap construction and leach procedure were similar to those described in the literature l, 2 with certain modifications to permit detailed monitoring of the operation. In May 1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the following reasons: (1) The necessary equipment for heap construction was readily available. (2) Stockpiles of mineral from the various mining sites were on hand: (3) Construction of the heap could be made on an abandoned tailings pile minimizing problems associated with environmental approval. (4) Proximity of the mill would allow product streams to be absorbed into existing circuits. (5) Necessary utilities were available. (6) Tailings water from the existing circuit could be used for leaching. A program for the pilot heap leach was developed with the following primary objectives. (1) To confirm the data obtained in bench-scale tests particularly on uranium recovery, acid usage, and ore permeability. (2) To evaluate plastic liners used for base preparation. (3) To investigate heap configuration variables. (4) To determine heap leach amenability of the different mineral sources. (5) To establish the economics of heap leaching low-grade ores.

Jan 1, 1979