Search Documents

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By Gabriela Moreira Lana

A radiação solar apresenta uma enorme variedade de aplicações de engenharia, dentre elas, a conversão em energia térmica em concentradores solares. Os tubos absorvedores dos concentradores solares podem ser recobertos por cromo negro, com o objetivo de otimizar a absorção energética e a durabilidade. Esse trabalho é parte de um estudo complexo sobre esse tipo de recobrimento. Foram desenvolvidos filmes de cromo negro por eletrodeposição sobre aço inoxidável AISI 304 e tratados termicamente a 600°C por 2 horas. Os filmes foram caracterizados antes e depois do tratamento térmico, utilizando-se microscopia eletrônica de varredura (MEV), espectroscopia de energia dispersiva (EDS) e difração de raios X a baixo ângulo de incidência (GAXRD). Além do cromo, observou-se deposição de cobalto e elementos residuais do banho eletrolítico. O estudo da estrutura cristalina mostrou formação de óxidos após tratamento térmico. Microestruturalmente, foram observados filmes com estrutura lamelar ou nodular. O estudo permitiu sugerir modificações do banho eletrolítico, do substrato e métodos adicionais de caracterização.

Aug 17, 2017

In 1950, about a third of the world?s population lived in cities. That figure has steadily risen throughout the following decades. Now it is believed that about 60 percent of the estimated 8.1 billion people in 2030 will be living in urban areas. The strain on infrastructure in cities in the developed world is already showing. And the rapid growth in developing nations today is adding to the shortage of materials, equipment and labor needed to keep up with this growth. So, while materials and labor may be in short supply, there is no shortage of work for the underground tunneling and space industry. In June, 718 of those professionals from around the world were in San Francisco, CA for the North American Tunneling (NAT) conference, put on by the Underground Construction Association (UCA) of SME. The attendees spent the three days of technical sessions listening to international authors discuss the state of the industry, new technologies that have become available and updates on major tunneling projects throughout the world. The accompanying exhibit attracted 79 vendors, who displayed the latest in tunneling and underground space equipment and services. In addition to the technical sessions and the exhibit, the NAT featured three short courses ? ?DRB Process Update Workshop,? ?Soft Ground Tunneling Technologies? and ?Underground Blasting Technology and Risk Management.? And the post-meeting field trip to the Devils Slide tunneling project near San Francisco was sold out.

Jan 1, 2008

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

By Paula Aliprandini

Os minérios limoníticos de níquel apresentam na sua composição metais como ferro, níquel e cobalto, sendo o primeiro o elemento majoritário. A presença majoritária de ferro prejudica a separação dos demais metais que possuem interesse comercial. Para remoção do ferro, técnicas hidrometalúrgicas são usadas. A extração por solventes é uma técnica com foco na separação seletiva de metais. Neste trabalho, foi preparada uma solução sintética baseada nas concentrações dos metais presentes na lixiviação de um minério limonítico de níquel. A solução foi colocada em contato com o extratante Cyanex 272. Este extratante é conhecido pela sua seletividade ao ferro em valores de pH próximos a 2,0. As amostras foram analisadas utilizando a técnica de Espectroscopia de Fluorescência de Raios X por Energia Dispersiva (EDX). Após concluídos os ensaios foi encontrado que durante a extração do ferro, o cobalto foi coextraído junto, mesmo em pHs entre 0,5 e 2,0, indicando que a presença do ferro altera o comportamento do cobalto.

Aug 17, 2017

By Brian G. White

Two examples of en echelon mining-induced fractures seen in hard-rock mines provided a basis for inferring that fracture zones and bedding plane separations immediately surrounding mine openings are promoted by oblique shear into the openings. It is hypothesized that initial fractures or separations form at the corners of openings as a result of high stress and physical constraint on the rock's ability to deform elastically toward the opening. These conditions result in a locally preferred direction of shearing. The shearing, in turn, generates tensile stress that initiates a progression of systematically offset fractures approximately parallel to the direction of greatest compressive stress. The fractures or bedding separations create tabular rock layers that amplify shearing displacement through bending and dilation. Such shearing effectively reduces and redistributes the compressive stress, but significant dilation is an inevitable consequence. The combination of dilation and shearing and the progressive development of fracture zones have important implications with respect to ground support. The concept of mining-induced fractures forming as a result of shear is illustrated by two examples from coal mines. First, fractures seen at longwall faces probably result from shear associated with subsidence. The fracture zone that develops approximates or possibly defines the draw angle of subsidence. As the face advances, fractures extend downward along the lower edge of the fracture zone, while upper extensions of the fractures are pressed closed. Fracture zones in entry roofs provide a second practical example. Here, mining-induced fractures typically follow bedding planes. The shear zone model suggests that the first bedding separations develop near the edges of the roof and successive separations progress upward and toward the center. However, if the direction of greatest stress is inclined with respect to the roof, a fracture or bedding separation zone may propagate from one side only and also extend higher. Because coal ahead of the face provides some support against lateral shear deformation, bedding separation is inhibited near the face. Rock bolts installed close to the face ultimately become more strained and bent than bolts installed a few meters from the face, and bolts installed through the more remote part of a separation zone may ultimately experience the greatest tensile and bending strains. This model is supported by field data documenting progressive bolt failures that rapidly propagated downward across the roof during face advance.

By T. Tamagawa, N. S. Fu, I. Iwasaki, M. Kobayashi

A 3-stage fluidizing bed process of chlorination, selective oxidation and sulfur chloride conversion was tested for processing of a chalcopyrite concentrate. It was found that the use of excess oxygen was essential to a stable operation in the oxidation reactor. The oxygen-excess gas will inevitably cause the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and the selective oxidation steps with separate flow paths of the fluidizing gases, thereby preventing the passage of oxygen-excess gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratory-scale fluidizing bed setup.

Jan 1, 2000

By J. Paraszczak

Application of teleoperated and automated (or ?autonomous?) mobile equipment in underground metal mines is a promising avenue for overcoming some of the challenges facing mine operators. These include, but are not limited to, the issues related to safety and health of underground workers, better use of the shift time leading to increased productivity, skilled manpower shortages, and remoteness of some mine sites. Autonomous load-haul-dump machines and trucks offer several benefits over man-operated ones, but their use at their full capacity is a challenging and complex task. This paper makes an overview of commercially available equipment and systems and their applications. It examines factors affecting adversely availability, utilization, and production efficiency of autonomous vehicles and compares them to conventional man-operated machines. Technical and operational aspects are discussed and their criticality is analyzed. Based on that, recommendations concerning means and measures that may help raise operational effectiveness are given. It is stressed that due to a scarcity of publicly available information on the performance and cost of autonomous loading and haulage operations, more field studies and in-depth analysis are needed.

Feb 23, 2014

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By Carolina Passanante

Aços Inoxidáveis Supermartensíticos surgiram na indústria petroquímica como um material alternativo para confecção de dutos, devido principalmente ao sinergismo de suas propriedades mecânicas e de corrosão. Com esta nova demanda, tornou-se necessária a caracterização deste material em suas diversas propriedades, destacando-se neste trabalho o efeito da microestrutura na resistência à corrosão. Objetivou-se, portanto, o estudo da resistência à corrosão por pite de um aço inoxidável supermartensítico 13Cr-5Ni-2Mo-Nb em função da fração volumétrica de ferrita-delta (d) presente na microestrutura. A variação da ferrita-delta foi alcançada através de tratamentos de recozimento, a 1.050°C, durante diferentes tempos (de 0,5h a 48h). As amostras foram submetidas a ensaios de polarização potenciodinâmica em eletrólito contendo 3,5% NaCl, naturalmente aerado. Quantificou-se, ainda, a porcentagem de ferrita em cada uma das condições através de ataque eletrolítico com solução 20% NaOH. Os resultados obtidos evidenciaram a diminuição desta fase com o aumento do tempo de recozimento, chegando praticamente à sua eliminação com tratamento de 48h. Paralelamente, a resistência à corrosão por pite deste aço foi melhorada de modo proporcional à diminuição da fase ferrita, resultando em um aumento de aproximadamente 115 mV da pior para a melhor condição, comprovando que, de fato, a presença de ferrita-delta prejudica as propriedades de resistência à corrosão localizada.

Aug 7, 2018

By Juan M. Antorena

A dynamic testing program was performed to evaluate installation procedures, assess capacity of 610-mm (24-inch) diameter open ended steel pipe to evaluate set-up and provide minimum pile tip elevation based on the dynamic testing results. The program was performed for a marine terminal project consisting of a 570-meter (1900-foot) long, overwater railroad trestle. The project location is Santa Marta, Colombia, South America. The subsurface profile generally consisted of 4m (12 ft.) of water and soft to hard silty clays. The piles were installed to an approximate tip elevation of -22 meters (MSL). Three piles were initially dynamically monitored during installation and then later monitored during restrike driving to evaluate pile drivability and bearing capacity including time related capacity increases due to soil "set-up". Knowledge of change in pile capacity with time after end of initial driving is important for design of pile foundations.

Jan 1, 1995

By F. Calizaya

The Western Mining Training and Translation Center is a consortium of four universities devoted to developing educational and training projects to reduce the incidence/accident rates in the mining industry. The center consists of Missouri University of Science and Technology, Montana Tech, the Colorado School of Mines and the University of Utah. It is fully funded by the National Institute for Occupational Safety and Health (NIOSH). The center manages 15 educational projects and one translation project. Hazard Identification and Risk Assessment (HIRA) for Small Mines is an educational project managed by the University of Utah. The objectives of this project are to identify critical mine hazards, assess risks; outline procedures to reduce accident/incident rates in small mines in the western United States and to train mine workers and super-visors on HIRA in each participating mine. To accomplish these objectives, the HIRA personnel visited 15 small mines in Utah, Colorado, Nevada and California. At these mines, most operators were employing independent contractors to perform several tasks ranging from drilling, blasting and mucking of rock at the work site to hauling ore to a processing plant. The operation of diesel-powered equipment was one of the major tasks performed by the contractors. This article presents three case studies in which contract workers performed a number of tasks with no reportable incidents but did so unsafely. It also highlights the training received by most contractors, the constraints imposed upon them and the safety hazards to which they are exposed most frequently.

Jan 1, 2008

By J. O. Marsden

Over the past eight years, Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold, Inc.) devoted a significant amount of effort to the development of a suite of processes for the effective hydrometallurgical treatment of copper sulfide concentrates. This effort resulted in the development of high-temperature (>200ºC) and medium-temperature (150° to 165ºC) pressure leaching processes. Specific configurations of both processes have been commercially demonstrated at Phelps Dodge?s facility in Bagdad, Arizona. This paper reviews in detail the chemistry of medium-temperature pressure leaching of copper concentrates and reports on the process development work conducted by Phelps Dodge and others for this technology. This paper is Part I of a four-part series on this technology. Part II covers the development of medium-temperature pressure leaching and direct electrowinning technology; Part III considers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By B. P. Faulkner, M. Weinecke

Svedala started a development program in 1997 to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed short-comings in the various approaches either process, mechanical, combination of factors, or trying to emphasis the production of low value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot plant development and commercial plant design.

Jan 1, 2001

By Mariana Sizenando Lyrio, Fernanda Nascimento Moreira, Weslley Luiz da Silva Assis, Harison da Silva Ventura, Gabriella Maria Silveira de Sá, Ana Gabriella Conceição dos Santos

surgimento de fases intermetálicas em aços é matéria de grande interesse devido ao caráter nocivo que elas podem conferir às propriedades mecânicas do material. No presente trabalho, foi estudado o efeito do surgimento da fase sigma em um aço inoxidável duplex através de modelamento numérico-computacional. A microestrutura duplex foi obtida via simulação, sendo, então utilizada como matriz para a nucleação e crescimento da fase sigma, também via simulação. O método do Cone Causal foi utilizado para o desenvolvimento da microestrutura e os resultados foram comparados com a metodologia da cinética formal de JMAK para fins de validação do modelo. Os resultados da simulação permitem obter, através da Regra das Misturas, predições sobre as propriedades mecânicas do material, no caso, o limite de resistência à tração, que foi comparado com os dados encontrados na literatura. Foi possível constatar o aumento do limite de resistência à tração para maiores frações volumétricas de sigma, o que traz como resultado a diminuição da ductilidade para o aço.

Nov 17, 2019

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

WipFrag systems I and II have become the world standard in photoanalysis systems to measure fragmentation. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved to allow automatic measurements of the size distribution of patiicles on moving conveyors, in truck boxes and on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1997

By John A. Herbst, Alexander Potapov, Xiangjun Qiu

"High Fidelity Simulation is a name applied to the use of first principles modeling tools including Discrete Element Modeling (DEM), Computational Fluid Dynamics (CFD) and Discrete Grain Breakage (DGB) to mathematically describe and study processing systems. Over the past few years, significant advances have been made in High Fidelity Simulation applications, particularly as many mineral processors have been drawn to the study and use of DEM of grinding mills for optimization purposes. This presentation provides an introduction to High Fidelity Simulation, with an emphasis on DEM. It will include insights into current applications of these tools including the optimal design (wear and throughput) of mill lining systems and media selection, the analysis and design (flow and efficiency) of the back-end of grate discharge mills. Advantages of full mill simulations versus individual sub-process simulations will be demonstrated for a SAG mill with different discharge system designs.INTRODUCTIONHigh Fidelity Simulation is providing mineral processors with the opportunity to analyze the behavior of mineral processing equipment from a fundamental or microscale point of view. In the past complex phenomena such as tumbling mill grinding had to be analyzed using black box tools such as residence time distributions for transport and classification functions for passage of particles through grates; while breakage had to be analyzed using PBM models who derived their form from theory but required direct measurement of kinetics. Today with the help of DEM, CFD and DGB these can be analyzed at a very fundamental level.The key element of DEM simulation is the application of Newton’s laws of motion to individual objects or discrete elements. Using this simulation method one can describe the position, velocity (both translational and rotational) of all objects and the transfer of momentum to other objects (Mishra and Rajamani, 1992; Cleary, 1998; Nordell et al, 2001)."

Jan 1, 2003

The seams of black coal occurring in Victoria are so disturbed by faulting, wash-outs, thinning, etc., that it is necessary, for the prevention of costly errors in development, that close boring be undertaken so that the correct positions of the shafts, tunnels, main and auxiliary roadways can be set out in order that the area can be economically worked. The State Coal Mine has two boring plants continuously at work, which have given good service for the last twenty-five years.The information supplied herein is merely our experience in boring at the State Coal Mine over an extended period. The type of plant in use is that known as the Victoria Drilling Plant, equipped with an 11 h.p. portable oil engine, using power kerosene as fuel. It was purchased in 1914, complete with mechanism for cable drilling, capable of boring to a depth of 1500 ft. with a guarantee of 1000 ft., with Calyx cutters, boring rods and all necessary equipment for the sum of £1473. The chief mechanical features of the plant are as follows:-The derrick is in the shape of a tripod (see Fig. 1), two of the legs being of steel channel built together to form a frame which, when lowered on to two sets of road wheels, forms a carriage for the transport of a portion of the boring equipment. The third leg is made of oregon in the form of a double bow, with bolts and distance pieces between the wooden sides. The top of this is hinged on to the steel frame, and the bottom is fitted into a cast iron block, having two small wheels to facilitate erection. A rope attached to the cast iron block and to the winch easily...

Jan 1, 1936

By Thiago Figueiredo Azevedo

Ligas de titânio e nióbio têm sido desenvolvidas devido a possibilidade de modificar as propriedades mecânicas por envelhecimento. No presente estudo ligas TiNb com diferentes concentrações de Nb e com adição de estanho foram obtidas por fusão a vácuo, deformadas a frio e posteriormente tratadas por diferentes tempos de envelhecimento. Foi observado que todas as ligas em todas as condições apresentam as mesmas fases ß, a” e ?, no entanto, apresentam diferentes microestruturas. Isso se refletiu nas propriedades mecânicas das ligas, onde obtevese maiores durezas com o envelhecimento em 48 horas em todas as ligas, esse aumento de dureza foi quase o dobro para as ligas com maiores teores de nióbio (Ti42Nb e Ti42Nb2Sn).

Aug 16, 2017

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007