Search Documents

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

By E. W. Felegy

Since 1920, the Bureau of Mines and, other agencies have conducted numerous investigations of methods of communication for use in mines in times of disaster or emergency. The results of these investigations have been reported in various publications (3, 4; 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16). In November 1944, the Bureau of Mines resumed the study of emergency underground communications. Until March 1946, the program was directed toward reexamining methods of underground communication that indicated possibilities of success. Since April 1946, the principal interest of this investigation has been in methods of application of radio to communication in mines, low-frequency radio seeming to offer the most promise as a successful method of emergency mine communication. Results achieved in reexamining other methods and in the investigation or the application of low-frequency radio between November 1944 and September 1946 were reported previously in a publication entitled "Some Studies on Emergency Mine Communications".

Jan 1, 1948

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015

THE ore treated is almost pure copper pyrites (chalcopyrite) in a gangue of quartz and quartz-felsite. Very little free iron sulphide (pyrite) occurs, and at the time of the erection of the flotation plant the stopes in the oxidized zone had been almostentirely depleted. This zone only extends to a shallow depth, and, below the l00-ft. level, the sulphide for the most part is clean and bright but in the crushed and brecciated parts of the ore channel, where surface water has circulated freely, the gangue is decomposed and kaolinized, and the copper sulphide badly tarnished. This class of ore gave considerable trouble at the mill, but unfortunately, was very limited in quantity. A sample of rich ore assayed-Copper, 21.2 %; iron, 24:.3 %; silica, 28.9 %; sulphur, 25.1%.The concentration in the original mill was effected by handpicking, jigging, and tabling. A considerable portion of the copper mineral arrives at the surface in the form of large lumps of very pure quality, eminently suitable for sorting out by hand.The rich ore is tipped over a grizzly at the shaft bins; the oversize hand-picked, and the undersize bagged direct.

Jan 1, 1912

By Gaulton R

The Commission maintains a data base first computerised in 1957 and containing information from over 18 000 boreholes located mainly in the Latrobe Valley area. Some of the borehole derived information dates from the turn of the century, although most of it has been collected as a result of Commission investigations conducted over the past 40 years. The Resource Data Base contains not only information gained directly from the drilling itself but includes the results of chemical and physical testing on many hundreds of thousands of samples retrieved from boreholes. Replacement value of the Resource Data Base has been estimated to be around $200 million, and it's integrity and accessibility is clearly of paramount importance, not only to existing mining and power generating functions but to the future evaluation and use of the vast brown coal Resource.

Jan 1, 1992

By T. G. Ewart

INTRODUCTION FOR THE purpose of this paper, western bituminous coal is defined as steam coal produced in Alberta and southeastern British Columbia for sale primarily to railways and industries. Before examining present and future markets of this industry, it is proper to review briefly financial and operating conditions within the industry. The report of the Royal Commission on Coal, 1946, supplies financial data from which some conclusions may be drawn. In 1944, the industry as defined above had share capital of $24,886,696. In the fifteen years 1930 to 1944, inclusive, the industry produced: 44,364,211 tons of coal. The profit on this tonnage amounted to $4,678,382.58, which represented 10.6 cents per ton of production. Miscellaneous earnings increased the amount available for dividends to shareholders to a total of $8,487,952.41, which is equal to, 19.1 cents per ton of production. Dividends actually paid in this fifteen-year period amounted to $12,332,040.64, which represented an annual average rate of 3.40 per cent on share capital. It is worthy of note that, in 1944, the net current position of the industry, including investments, was $8,753,874.51. The writer believes that the financial position of the industry with respect to capital, current financial position, and net earnings, has not significantly changed from the fifteen-year period out-lined above. The figures quoted indicate the following situation: (1) The western bituminous coal industry is adequately financed. (2) The industry has followed a conservative dividend policy and has accrued funds for contingencies. (3) The industry has sold its production at very reasonable prices as evidenced by its moderate earnings per ton of production.

Jan 1, 1951

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

One of the most energy-intensive processes for producing submicron range calcite is stirred media mill. In the present work, numerous operating parameters such as solid mass fraction, grinding media size, media filling ratio, and grinding time have been investigated using a vertical type stirred media mill. The results are evaluated on the basis of mean particle size, specific surface area, and specific energy consumption. After conducting this study, optimum experimental conditions found to be as 70% media filling ratio, 25% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. Besides, energy savings up to 22% were achieved with the choice of proper media size.

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Clarke P. E

At the end of the recent war, reports became available from Europe of the use of tungsten-carbide inserts in percussion rockdrill bits. These bits were used with small size rockdrills, so that the only advantage gained from the use of the harder, abrasion resistant, tungsten-carbide appears to have been the greater life of the bit. Larger machines, such as used in Australia in conventional practice, had to be discarded to protect the relatively brittle tungstencarbide inserts and the vulnerable bonding with the bit body.As it had been found in machine shop practice that some grades of tungsten-carbide had been produced with considerably improved toughness, it was decided by Gold Mines of Australia Ltd. that drilling practice with tungstencarbide bits warranted detailed examination under Australian conditions, and that drilling tests should be undertaken at Morning Star (G.M.A.) Mines N.L., for which it acts as General Manager and Consultant.These investigations progressed through three stages:1. Preliminary Investigations and Tests.When the investigations were initiated no commercial bits were available in Australia, and manufacture was commenced with improvised equipment from virtual scratch. These early tests indicated that the use of 3 in. bore rockdrills in conjunction with tungsten-carbide insert bits was a 'possibility, and that it was unlikely that a small bore...

Jan 1, 1950

By Larissa Manso Miguel Gonçalves

A partir da latente necessidade de se manter competitivo perante seus concorrentes, as empresas vêm buscando se diferenciar através de inovações e melhoria contínua de processos. Com base nesse conceito a Logística CSN Aços Longos realizou mapeamento dos seus processos para que fosse possível mensurar sua eficiência. Avaliando o ciclo total do pedido através da medição dos tempos de Coleta (entrada do pedido à oferta de veículo), TPV – Tempo de Permanência do Veículo (carregamento) e Entrega (viagem), foi desenvolvida uma ferramenta para medição do Nível de Serviço da operação. Com a constante evolução do mercado e à elevada exigência dos clientes, isso se torna um diferencial, agregando valor aos produtos e fidelizando clientes. A ferramenta contribuiu para melhora significativa na tomada de decisões quanto às atividades críticas e sua consequente contribuição à satisfação dos clientes.

Oct 30, 2017

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

By Edwan Anderson Ariza Echeverri

O aumento das exigências para reduzir o consumo de combustível e aumentar a segurança dos passageiros tem estimulado o desenvolvimento da nova geração de aços de alta resistência. Esses objetivos tornam-se atingíveis com a redução do peso dos componentes de aço do veiculo, pelo uso de chapas mais finas e resistentes, mas não menos dúcteis. Com esse propósito, no presente trabalho pretendeu-se analisar os efeitos de diferentes rotas de processamento: estampagem a quente, têmpera e partição e o inovador processo que combina a deformação a quente com a têmpera e partição. Os ciclos térmicos foram projetados para obter a maior fração de austenita retida, além de ferrita e martensita. Para cada amostra tratada, amostras de tração de tamanho reduzido foram extraídas de amostras previamente tratadas em simulador termomecânico avançado Gleeble 3S50. A microestrutura foi analisada por microscopia óptica e eletrônica de varredura. Com o novo processo combinado acredita-se que seja possível atingir uma boa associação de propriedades para a nova geração de aços de alta resistência pela transformação da austenita retida metaestável em martensita induzida por deformação, contribuindo para a absorção de energia durante impacto.

Aug 16, 2017

By S. Ndlovu, M. Malatse

"The Witwatersrand Basin is the heart of South Africa’a gold mining industry. The cluster of gold mines located in the Witwatersrand Basin generates a significant amount of mine tailings, which have adverse effects on the environment and ecological systems. In addition, disposal costs are very high. The exponential population growth in the Witwatersrand area has resulted in pressure on the reserves of traditional building materials. Quarrying for natural construction material is very expensive and damages the landscape. This work therefore examines the use of gold mine tailings in the production of bricks.Different mixing ratios of gold tailings, cement, and water were used. The resulting bricks were then cured in three different environments - sun dried, oven dried at 360°C, and cured in water for 24 hours. The bricks were then tested for unconfined compressive strength, water absorption, and weight loss. The results showed that the mixture with more cement than tailings had a compressive strength of approximately 530 kN/m2. It was also found that the best brick curing system was in a water environment. Bricks made from tailings cost more than conventional bricks because of the higher quantity of cement used, but the manufacturing process consumes less water. Overall, the results indicated that gold mine tailings have a high potential to substitute for the natural materials currently used in brickmaking.Paper written on project work carried out in partial fulfilment of BSc. Eng. (Metallurgyand Materials Sciences)"

Jan 1, 2015

By M Scoble, A Ostry, J Shandro

Mining companies are not ill-informed on the topic of community health. There have been a number of research studies that have illuminated community health issues associated with mining, especially in the western Canadian province of British Columbia. However, what is missing amongst the literature is the perspective of mine managers and mining executives on this topic. This is important as mine managers and executives face a number of issues related to community health and are under pressure to consider the topic in more detail. This paper presents results from an exploratory qualitative investigation based on grounded theory research techniques into current community health considerations from the perspectives of mine executives and mine managers working in Western Canada. Interviews were conducted between February and May 2012 with 11 mining versus ten mining executives and managers who represented operating mines or mining umbrella organisations in Western Canada. Participants report on general community health issues that are perceived to be important, the perceived role that the mining sector should play?in contributing to community health and how this differs in Western Canada as compared to locations abroad, and?risks companyÆs face in making community health contributions. This paper concludes by drawing attention to pressing health needs that are present in Northern, rural and Aboriginal populations in Western Canada and provides a platform for future research initiatives focused on improving the health and well-being of communities associated with the mining industry. CITATION:Shandro, J, Scoble, M and Ostry, A, 2012. Community health considerations from mining executives and managers in western Canada, in Proceedings International Mine Management 2012, pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By D. Nyembe, B. Mamba, Antoine F. Mulaba-Bafubiandi

Copper and cobalt are generally electro-won from their aqueous sulphate solutions. After optimised leaching of their ores, concentrates or calcine bearing minerals, the leachate is clarified and suitably purified prior to the electrolytic extraction of the metal of pursuit (Pearcy, 2006). Solvent extraction (SX) using appropriate organic solvents and ion exchange (IX) with relevant resins are known purification processes used for copper and cobalt recovery (Stanely, 1970).As zeolites in general and natural zeolites in particular, demonstrate ion exchange properties (Korkuna et al., 2005), an attempt has been made to use Southern African natural clinoptilolite in the recovery of copper and cobalt from their aqueous sulphate solutions. Initially, synthetic Co and Cu solutions were prepared. Preceded by laboratory ore leachate, plant solutions are to be used. AAS, XRF, XRD, Mossbauer spectroscopy and BET were characterization techniques used. Natural clinoptilolite was used as-received as well as acid activated; and cobalt and copper extractions were performed at room temperature.

Jan 1, 2007

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By Johnston W. H

MINING operations in the Waihi mine began, under the present proprietorship in the year 1889. Previous to this, and as far back as the year 1880, the presence of reefs in the Martha Hill had been known, and surface working on a small scale had beencarried out, without any great measure of success. The only method of treatment in use at this time was the old system of light stamps, amalgamating tables and berdans, and recovery by this method being low, little margin for profit was left, so thatthe property in these days was not considered of great importance and work on the area was only carried on spasmodically by different owners.On the transfer of the leases to the present company, calcining, dry crushing, and hot pan amalgamation was adopted as the method of treatment, and this system was continued till the more modern cyanide process was introduced and applied. As themethods of treatment and gold-saving became more efficient with the application of more modern and scientific processes, the importance and future prospects of the mine became more and more pronounced, and mining on a larger and more comprehensive scale was gradually established.As in the case of ore treatment, mining methods in the early stages were not as far adv.anced as the adopted practice of today, and numerous shafts, levels close together in vertical height.

Jan 1, 1912