Search Documents

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

The Full Scale Model Roof Bolt Test System described herein was designed, fabricated, erected, and installed by MSA Advanced Systems Division for the U. S. Department of Interior, Bureau of Mines, Spokane Research Center. It was furnished under USBM Contract No. 50271014 and Modifications. The test system is intended for use by the Bureau of Mines to run comparison tests on roof bolt systems. The mine entry cross section is made from special concrete pillars and roof slabs. They are constructed within a steel beam frame with hydraulic operated cylinders to apply loads that simulate the action of mining overburden. The frame is designed so it can be disassembled for replacing the concrete in subsequent tests. A computer and data acquisition system is furnished to control the load application and measure and gather data.

Jan 1, 1979

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

By Jos. R. Guiteras

This paper is one of a series published by the Bureau of Mines on mining and milling methods and costs. It describes operations in the Alma district of Colorado in September 1937, supplemented by some additional data collected in July 1938. ACKNOWLEDGMENTS The author wishes to express his appreciation of the friendly cooperation extended him by the mine operators in the district. The greater part of the information was obtained from mine and mill superintendents to whom individual acknowledgment is made in the text.

Jan 1, 1940

By B. M. Larsen

Jan 1, 1948

By B. M. Larsen

Jan 1, 1948

By Jeffrey M. Listak

This U.S. Bureau of Mines report describes the implications of in-mine ground control on the automated or remotely controlled operation of longwall mining equipment, Perhaps the greatest challenge to longwall automation researchers is the development of systems that will continuously function in the complex and unpredictable underground environment. The high degree of environmental variability, together with conditions brought about by the extraction process, makes complete automation of longwall mining a difficult task. The intellectual thought processes and split-second decision making required to avert disasters are lost when workers are removed from the face. As many mine operators can attest, minor problems, left unresolved, can eventually accumulate and lead to catastrophic consequences. The automation process will have to assess and manage various routine problems that are otherwise resolved through worker observation and experience.

Jan 1, 1990

Once every three years the eyes of the construction and mining industry?s turn to Munich, Germany for the bauma trade fair and exhibition. From April 19-25, Messe München International (MMI) will host the 29th edition of this massive show that, despite the recent recession and global financial struggles, has grown yet again. The show, which is completely booked, will take place on a record 555,000 m2 (5.9 million sq ft) of indoor and outdoor exhibition space at the New Munich Trade Fair Centre. More than 3,000 exhibitors are expected to make use of this event. To prepare for the show that highlights some of the largest and most impressive construction and mining equipment in the world, Messe München began working months in advance on getting the infrastructure on the open-air site ready, in time for the arrival of the gigantic machinery exhibits, which started to arrive in March. Part of the preparations include a new entrance at the northwest corner of the exhibition center that was built to regulate visitor flow better. This should help with bauma considering that in 2007 more than 500,000 visitors passed through the gates. ?Although in 2010 the construction machinery sector in many markets worldwide will be recovering only slowly from the recession, we are pleased to report that we are seeing strong demand for exhibition space. This shows that exhibitors regard participation in the world?s leading trade fair bauma as a must, although many are at present having to make cuts in their advertising and trade-fair budgets. We have been particularly surprised by the strong demand for space from exhibitors from markets like China, India and Turkey. The fair is fully booked and many more companies are on the waiting list,? said Eugen Egetenmeir, managing director of Messe München. More than 50 percent of the exhibitors at bauma 2010 come from countries outside of Germany. While the show?s primary focus is on the construction section, it is not as if the mining sector will be difficult to find. With some of the largest equipment in world on display in section C2 (Fig. 1), the mining industry is sure to be well-represented.

Jan 4, 2010

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

The Canadian concept for nuclear fuel waste disposal is being assessed by AECL Research in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet. Manitoba, Canada. As pan of this research, the Mine-by Experiment has been designed to obtain information on rock mass behavior, the development of an excavation-induced damage zone and failure mechanisms around a circular bored tunnel. An iterative design approach was used to effectively reconcile the experiment objectives and construction logistics. This paper discusses the design considerations and construction methodology adopted on the project.

Jan 1, 1991

By CHARLES R. KETES

I. INTRODUCTORY. Lake Valley, New Mexico, has long been one of the most widely known mining districts of southwestern United States. For many years its silver-mines have been among the most famous of the country, visited by many mining men and geologists; yet little information regarding the origin of the ore-deposits and the influencing geologic conditions has found its way into print. With the recent revival of public attention, after a decade and a half of utter stagnation, to the mining of silver in the Southwest, special interest attaches to the genesis and geologic disposition of the ore-bodies which are so finely open to inspection in the Lake Valley district. Moreover, the local features here described are typical of the conditions existing over a much larger field. The fact that the ores are chiefly the chloride and the chloro-bromide of silver adds further interest. Data bearing upon the genesis of haloid ore-deposits are, at the present time, very much sought. Arid regions offer particularly favorable conditions for the formation of such ores. This New Mexican district appears to supply solutions to many problems concerning this class of ores, which have long vexed the student of ore-deposits. II. LOCATION AND HISTORY. The town of Lake Valley is situated in Sierra county, in the southwestern part of New Mexico, and 100 miles northwest of El Paso, as the crow flies.From a mining standpoint, the location of the place is itself suggestive, as it lies on the southeastern slope of the great quaquaversal arch of the Colorado plateau. The center of this vast dome is in north-central Arizona, and radii about 150 miles in length reach its foot in all directions. Around its basal margins runs the broad mineralized belt containing most of the great mines of the Southwest, which extends from south-central Colorado southward and southwestward through New Mexico, thence westward through Arizona, northwestward and northward through southeastern California and western Nevada, and, finally, eastward through Nevada and Utah into Colorado again. This great mineralized belt is important as geographically limiting profitable mining over the greater part of five States.

Jan 1, 1908

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

1. BOYD, JAMES. Statement on the Investigation of Natural Resources. Hearings before National Re-sources Economic Subcommittee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 125-131. 2. BUCH, J. W., HENDRICKS, T. A., AND TOENGES, A. L. Statement on the Investigation of Natural Resources. Hearings before National Resources Economic Sub-committee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 231-235. 3. CONGRESS, U.S. An Act to Provide for the Establishment and Operation of a Research Laboratory in the Pennsylvania Anthracite Region for Investigation of the Mining, Preparation, and Utilization of Anthracite, for the Development of New Uses and Markets, for Improvement of Health and Safety in Mining, and for a Comprehensive Study of the Region to Aid in the Solution of Its Economic Problems and to Make Its Natural and Human Resources of Maxi-mum Usefulness in the War Effort. Public, No. 812, 77th Cong., 2d sess. (S-357), ch. 764, approved Dec. IS, 1942, 2 pp.

Jan 1, 1962

By Paul M. Tyler

The technology of clay and the manufacture of ceramic products therefrom, and also the clay resources of most of the individual States, are already covered by a voluminous literature. The present resume touches these matters only briefly; its purpose is essentially to bring together in small compass certain of the elementary factors affecting the potential commercial value of a clay deposit. In its preparation the author made extensive use of the annual chapters on Clay in Mineral Resources of the United States and in the two annual issues of the Minerals. Yearbook that succeeded them. For careful review and constructive criticism of the manuscript, the author is indebted to Hewitt Wilson. GENERAL DESCRIPTION The term ?clay? includes a great variety of substances that may differ widely in chemical mineralogical and physical properties. No two clays are exactly alike. All of them however, have the prominent characteristic of becoming more or less plastic when wet. Nearly all of the useful clays can be molded into articles, will hold their shape while being dried, and can be converted into a hard, rocklike substance by heat. Clay may, and in fact usually does, consist of a number of minerals among the commonest of which are kaolinite, quartz, feldspar, iron oxides, mica, bauxite, calcite, and manganese oxides. Organic matter is often present. Pure kaolinite, which has the formula A1203. 2 SiO2. 2H2O, is ordinarily, considered to be the parent "clay substance," butt most clays contain other hydrated mixtures of alumina and silica (aluminosilicic acids) along with indefinite amounts of sand and other nonessential minerals3/ Even, this so-called inert matter affects the plasticity, drying shrinkage, ease of drying, and final density, and at high temperatures may react chemically with the clay substance.

Jan 1, 1929

By John P. Capp

Information is summarized on the major uses of fly ash and prospects for utilization in agriculture and in brick and mineral-wool manufacture. Technological aspects of utilization are discussed and references are given to the work of many of the leaders in the fields of fly ash production, processing, and utilization.

Jan 1, 1970

By H. Ehnes

"“Industry 4.0” – “Mining 4.0” - perhaps you have already heard of these terms? These keywords signify the next stage of industrial production. The internet and production technologies are growing closer together. Machines can communicate with one another, wherever they may happen to be located. The “Internet of Things” is the appropriate term. But what does SAFETY 7.0 mean? It is both brand new and traditional at the same time. It also has to do with the success of companies, with efficient production. And yet there is a great deal more at stake. It has to do with our lives and our safety – the supreme commodity in this world. What exactly SAFETY 7.0 means, what the number 0 stands for and the meaning of the number 7, and what this all has to do with mining will be explained in the following article. Mining is a fascinating undertaking. Mining is indispensable for a country’s economic development, whatever that may concern: infrastructure, energy supplies or raw materials for industrial production. Mining has brought forth many technological developments and innovations that can currently be found in our daily lives. Mining is impressive, grandiose and repeatedly fascinates mankind with its immense dimensions. Miners throughout the world still work hard and, for this reason, are bound to one another in a special way. In mining, every man looks out for the other; you have to be able to rely on each other. That creates a strong bond. The other side of the coin is that mining and disasters belong to normality in the media and thus also in our perception. Accidents at work and even catastrophes occur in mining, quarries, or raw material operations almost on a daily basis somewhere in the world. They are often associated with extremely serious injuries, or even a fatal outcome, for the miners affected and, in turn, dramatic consequences for the families of those involved. It could be in China, India, Russia, or somewhere in Africa, Asia or America – it mostly does not happen in front of our door or in our neighbour- hood. Perhaps because of this in the daily concert of negative headlines, we do not register these catastrophes any more in our minds. We write them off under the heading “Nothing special”, since there are, day in day out, more terrible news items about wars, civil wars, famines, or ecological disasters. Things only really change if there is a dramatic number of deaths or when we are personally affected, close by in the vicinity, or can witness the rescue action live. In Europe, these three mining disasters in particular have recently generated media resonance:"

Jan 1, 2016

By C. H. Mathewson

MY treatment of the subject of "Metals of the Future" is imaginative rather than statistical or scientific, because reliable information concerning useful concentrations in the form of ore deposits of by far the majority of the elements does not exist and the chemical, physical, and mechanical properties of the unfamiliar metals are recorded only in fragmentary and uncertain form or not at all.

Jan 1, 1944

By M. Bunch

"THE SUPER CYCLE IS GONE The utopia of the rising sales volume, for mining companies from 2002-2011, was entirely due to rising production volume and prices. The Australian mining sector experienced an 18 percent annual growth rate in revenues, and 11 percent growth in prices. (1) However, EBIT remained flat during the same time period. In addition, Australian mines saw a 7 percent annual decline in both labor and capital productivity. (2) Mines in the U.S. and Canada produced similar results, whereas the world-wide mining industry has seen a productivity drop of 40% since 2001. (3) The decade “Bull Run” of rising prices was trashed by companies that chased low-quality assets while increasing debt on their balance sheet. It seemed everyone believed the “super cycle” would last forever, while completely ignoring the history of cycle downturns. Worldwide mining operations are as much as 28 percent less productive today than a decade ago, according to new McKinsey research. The results from McKinsey’s new MineLens Productivity Index (MPI), which adjusts for declining ore grades and mine cost inflation, show that the pronounced decline in productivity is evident across different commodities and is seen in most mining players and geographies. (4) McKinsey sees three important areas of focus to address the root causes of productivity decline. 1) Embed effective management operating systems at mines 2) Prioritized operational excellence and capabilities development 3) Focus on innovation Reality has now settled back in and companies are struggling to make ends meet. The basic management staple of controlling costs and improving the production/productivity that was lost in the excitement is now back in play. Traditional cost-cutting approaches, such as across-the-board spending cuts, layoffs, and hiring freezes are only short-term initiatives and will not permanently improve a company’s cost structure or improve long- term competitiveness. This can only be accomplished by engaging front-line employees and empowering them to make necessary improvements in their daily work. It is time for leaders to lead and develop cultures of continuous improvement within their organizations in order to sustain their mining project to the end of mine life. Successful operating managers require two different skill sets of Leadership and Management; knowing how to lead people in their organization and how to manage the work they do."

Jan 1, 2016

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016