Search Documents

It is widely accepted that particles stabilise flotation froths and that stable froths result in improved flotation performance. Predicting the effect of particle addition on froth stability is, however, challenging. Dynamic surface tension measurement using maximum bubble pressure presents an attractive technique to investigate the effect of surfactant and particles at the air-water interface. The range of bubble lifetimes that can be studied (typically 0.1 to 60 s) is analogous to variations in air rate in flotation cells, and the corresponding changes in surface tension give an indication to the diffusion and adsorption rates of particles at the interface. In this paper, we use dynamic surface tension measurements to investigate the effect of particles on bubble surfaces at the microscale and link this to bulk froth stability measurements carried out using a froth column. Using the maximum bubble pressure method, the results show that the addition of particles results in lower surface tension, both at the dynamic (i.e. short) bubble lifetimes and towards equilibrium (i.e. 60 s bubble lifetime). This corresponds with the bulk froth stability measurements, where the three-phase system yielded more stable froths than the surfactant only system. Furthermore, increased particle loading at the air-water interface, whether through higher surfactant concentrations or lower air rates (longer bubble lifetimes), gave lower surface tension and higher froth stability. This demonstrates the link between bubble loading and froth stability. It is proposed that the maximum bubble pressure technique can be used to predict froth stability for two- and three-phase systems, enabling the effect of particle loading to be accounted for and quantified. Moreover, the technique has the potential to allow rapid determination of particle and surfactant diffusion at the air-water interface and prediction of the corresponding effect on bulk froth behaviour.

By Ted Klemetti

Roof deterioration in weak moisture-sensitive rock leads to roof falls in coal mines. An observation site was set up in intake air at an underground coal mine in central Ohio to evaluate the time-dependent deterioration of moisture-sensitive roof rock. By periodically collecting and weighing the rock falling from the roof, the National Institute for Occupational Safety and Health (NIOSH) was able to quantify the deterioration of the moisture-sensitive shale roof. The measurements showed that more roof rock is falling in the dry winter months. Movements in an intersection were monitored in order to determine if deformation correlated with seasonal changes in temperature and humidity. The rate of intersection roof-to-floor convergence was found to be cyclical and related to seasonal changes, with more convergence during the months of April through September. At the study site intersection, the roof beam did not show deflection indicating movement most likely due to mine floor deformation. The bolt load also increased in the warmer months before shedding load, possibly due to rock failure. Temperature and relative humidity sensors, placed in holes in the roof show that mine air does not mix with the air in the holes. Consistent saturation levels of relative humidity were measured in the holes and it appears that high levels of moisture may have migrated into the bolt holes from roof shales. A roof sealant applied to a portion of the test roof appears to be preserving the roof and reducing the amount of rock fall into the entry, while the screened area virtually eliminated rock falling from the roof.

Jan 1, 2009

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025

By Richard J. Finno

Detailed measurements made at a test section adjacent to a deep braced cut and other published data are combined to illustrate the limitations of the common methods of predicting movements associated with excavations in soft to medium clay. While past performance data can be used to estimate expected responses before construction in many cases, actual wall and soil deformations throughout construction can only be estimated using finite element procedures. Success of such analyses depends equally upon considering all aspects of construction that induce strains in adjacent soil, such as wall installation, excavation and bracing sequence, and time, and adequately modeling soil stress-strain behavior. Even when these two criteria are met, soil deformations can not be predicted adequately when strain levels exceed those that produce peak shear stress.

Jan 1, 1991

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

This paper describes the behaviour, under creep conditions, of a cast lead creep specimen consisting of five crystals, the boundaries of these crystals being substantially at right angles to the direction' of tension, i.e., across the long axis of the specimen. This particular specimen was obtained in an attempt to produce a single crystal in the manner described in the appendix of a previous paper (1).Thus, the specimen was of the same shape and size, was composed of the same purity lead and received the same preliminary treatment as the single crystal test-pieces.The object of the experiment was mainly to observe the effect of the crystal boundaries on both the deformation of the test piece and the process of recrystallisation and to compare the creep rate of the test-piece with that of a specimen consisting of one crystal only.EXPERIMENTAL METHODThe specimen had an effective test length of 10 cms. and a cross $ection of 0·5 in. x 0·25 in. In Fig. 1 is given a sketch of the specimen to scale showing the positions of the crystal boundaries on all four surfaces. Except for those of crystal No. 4, which was confined to approximately one-half the cross section of the specimen, the boundaries of each crystal traversed the four faces.The specimen was mounted in exactly the same manner as the single crystal specimens. During the creep test, it...

Jan 1, 1941

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

By J. H. Sokolowski, R. I. MacKay

The level of Si and Cu in the 3xx series of alloys affects the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase. The volume fraction of these phases in turn affects the feeding conditions during solidification and ultimately the Area Fraction Porosity and Mean Pore Diameter measured in the as-cast structure. This work sets out to establish the relationship between the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase and the resulting porosity that forms on the Monotonic and High Cycle Fatigue properties. The alloys in question are the Al-9%Si-l %Cu and a Al-7%Si-4%Cu alloys which were cast into V8 performance engine block castings and then heat treated to achieve desired mechanical properties. The engine block castings provided the mechanical and metallographic test samples analyzed for this work.

Jan 1, 2006

By A. C. Coetzee

Blinkpan Koolmyne is as ten voile gemeganiseerde steenkoolvoorsiener aan die 1 000 MW Evkom-kragsentrale in die Oos-Transvaal, onderhewig aan groat seisoenale produksieskommelinge. Die aanwending van 'n groat bogrondse oap opgaarhoop vir die uitstryking van hierdie wisselende aanvraag word beskryf. Twee produksierasionaliseringsfases wat hierop volg het besondere bemoedigende resultate gel ewer, beide in toerusting- en mannekrag-produktiwiteit. Die aanwending van 'n rekenaarprogram vir die simulering van ondergrondse afbouaktiwiteite met die oog op toerustingkeuse, word aangegee. Voorlopige resultate wat in die praktyk behaal is dui op 'n hoë mate van betroubaarheid vir die program, terwyl die gebruik van die nuutste tipe hoë -kapasiteit laaimasjiene, koolsnyers en wisselkarre, groat potensiaal inhou.

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By Y. Tang

The paper studied the extraction characteristics of the fly ash from a location in Guizhou province. Under ordinary pressure, the fly ash is extracted by an acid and alkali, and then studied for its reaction characteristics with different extraction agentia, temperature, consistence and time. The results of acid extraction show that there are good reaction characteristics for Fe2O3 with HCl and the extraction rate decreases with the increasing of extraction time. There are good selective characteristics between Al2O3 and H2SO4 and they weaken with the increasing of temperature and the expanding of time. The best extraction results are shown with CaO and MgO because of their chemical characteristics and the over-saturation degree of the extraction processing. In addition, It?s found that it cannot leach all the substances from fly ash even with the higher consistence (10mol/L) of extraction agent, the longer extraction time (2h) and the higher temperature (100?) .It shows that the extraction rate of Fe2O3 is 82.81% and that of Al2O3 is 29.01%. The results of alkali extraction show that the extraction rate increases with the consistence of extraction agent and temperature, and the extraction rate of SiO2 by NaOH increases rapidly with the time expanding while that of Al2O3 falls gradually.

Jan 1, 2014

By D. L. Morgan, J. A. Butterfield

"Geological data, production trends and current projects underway suggest that enough molybdenum will be available from more diversified sources to meet the world's growing demands. The growth in molybdenum consumption has been primarily related to its beneficial effects as an alloying agent in steel. This rapid growth has been deliberately fostered by stable prices, adequate supply and application research. The molybdenum industry is now in a process of change which has been seen in several other metals, such as aluminum and nickel. As supply sources have become more diversified, the market has become more competitive. The recent drop in consumption has led to excess production capacity, accumulation of substantial producer inventories and increased market uncertainties. While consumption is expected to increase in the next two to three years, it will take some time to absorb the excess capacity and inventory. The increased proportion of by-product capacity indicates that prices may become more variable. Producer discipline will be required to prevent serious price erosion in times of surplus. Future prices may not continue to increase with inflation. For the longer term, several factors favour the increased consumption of molybdenum. Engineering requirements are becoming more severe and molybdenum alloys can help to meet these changing needs. In addition, consumers can rely on a large and increasing supply of molybdenum. A 7 per cent growth rate in consumption can probably be sustained through the next decade, but new applications and reasonably stable prices will be needed to make this possible."

Jan 1, 1972

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By Khosrow Bakhtar

A series of nineteen shear tests were performed on fractures 1 m2 in area, generated in blocks of sandstone, granite, tuff, hydro- stone and concrete. The tests were conducted under quasi-static and dynamic loading conditions. A vertical stress assisted fracturing technique was developed to create the fractures through the large test blocks. Prior to testing, the fractured surface of each block was characterized using the Barton JRC-JCS concept. The results of characterization were used to generate the peak strength envelope for each fractured surface. Attempts were made to model the stress path based on the classical transformation equations which assumes a theoretical plane, elastic isotropic properties, and therefore no slip. However, this approach gave rise to a stress path passing above the strength envelope which is clearly unacceptable. The results of the experimental investigations indicated that actual stress path is affected by the dilatancy due to fracture roughness, as well as by the side friction imposed by the boundary conditions. By introducing the corrections due to the dilation and boundary conditions into the stress transformation equation, the fully corrected stress paths for predicting the strength of fractured blocks were obtained.

Jan 1, 1984

By K. H. Hofer

La mecánica de rocas se basa en el descubrimiento de las leyes que siguen las perturbaciones del estado natural de la corteza terrestre provocadas por la actividad minera. En ese sentido, el presente texto señala la importancia de este proceso en la ciencia de la minería -en tanto revisa el comportamiento de la resistencia de la roca, determina el estado de las tensiones primarias de la corteza terrestre y analiza la repartición secundaria de tensiones provocadas por la formación de huecos y sus consecuencias sobre la roca en el espacio y tiempo.

Nov 1, 1971

By Stênio Cavalier Cabral

O diboreto de titânio (TiB2) é um material cerâmico de alta dureza com uma grande potencialidade de aplicação tecnológica. No entanto, existe uma grande dificuldade de se produzir corpos bem sinterizados desse material, quando são usadas técnicas convencionais de sinterização. Neste trabalho, foi empregada uma técnica de processamento em altas pressões e altas temperaturas para produzir compactos de TiB2 com AlN. Amostras cilíndricas, com 5 mm de diâmetro e 7 mm de altura, foram processadas durante diferentes intervalos de tempo compreendendo os ciclos de sinterização. O principal objetivo do trabalho foi à realização do ensaio de torneamento para a avaliação de desempenho dos compósitos produzidos e sua relação com a quantidade de ciclos de sinterizaçãos em condições reais de trabalho. Os resultados obtidos apresentam perspectivas interessantes de utilização do processamento em alta pressão e alta temperatura para produção de inseros para aplicação na usinagem do ferro fundido nodular.

Aug 16, 2017

A consideration of mining ventures and the changes of an environmental nature that occur. The paper is introduced with a general statement claiming recognition that mining ventures are important to human well-being but that these need to be justified against the environmental changes that they bring about. The various factors that need to be considered are cited followed by an historical review of mining activities. The various environmental issues are discussed under three headings; socio-economic, physical and biological, prior to reviewing the world's demand for minerals including fossil fuels. In conclusion guidelines for appraising mining ventures relative to environmental changes that may occur, are given.

Jan 1, 1981

By Phillip I. Merritt

"IntroductionDuring and since• the war, it has been my privilege to work closely with those in Canada who are responsible for the vital raw materials needed in our co-operative atomic energy programme. The understanding which has developed between our two groups in this all-important enterprise has been a great source of pleasure. We in the United States are aware of the importance of the contribution made by Canada to this project, and we look forward to continuing our mutually advantageous relationship.The impact of World War II, and the decision by Canada, Great Britain, and the United States to join in a programme for the development of atomic weapons, created a sudden and immense demand for uranium minerals. Early in the raw materials programme, it was evident that sufficient raw materials to fulfill war-time atomic weapon requirements could be secured from three sources: the rich pitchblende deposits of the Eldorado , mine at Great Bear lake; the Shinkolobwe mine in the Belgian Congo; and as a by-product of the vanadium industry of the Colorado Plateau in the United States. In the early part of the programme, therefore, our joint efforts were directed toward obtaining immediate maximum production from these localities. The contribution made by Eldorado Mining and Refining (1944), Limited, both in supplying and refining raw materials, was and continues to be of vital importance.In addition, it was also obvious from the first that in this programme, as in any mining enterprise, exploration activities directed•toward the discovery and development of new sources of uranium ore were essential if production were to be maintained over an extended period of time. In order to satisfy obvious security requirements during the war, it was necessary to proceed with this exploration programme, both in Canada and the United States, as secretly as possible. With the end of the war, and the revelation that an atomic weapon had been developed, however, secrecy in exploration was no longer required. The important thing was to get on with a broadened exploration programme."

Jan 1, 1950

By C. M. Mason

The current Bureau of Mines active list of permissible explosives includes 95 brands. Twelve are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1968

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970