Search Documents

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By Edward C. Peterson

Recent studies indicate that the United States halt substantial reserves of ilmenite, one of the major titanium minerals. However, the studies showed that sources of rutile, another important source of titanium are limited. This paper summarizes and evaluates results and conclusions reached by the various investigations initiated by the Bureau of Mines and others pertaining to the titanium mineral resources of the Nation. Domestic occurrences of ilmenite that are economically exploitable by present-day beneficiation methods are found in Florida, New Jersey, New York, South Carolina, and Virginia. These deposits are estimated to contain 50.3 million tons of titanium dioxide (TiO2). Occurrences of ilmenite that cannot be processed economically under present technological conditions are found in California, Colorado, Minnesota, Montana, Oklahoma, Oregon, Rhode Island, and Wyoming. These reserves amount to 51.1 million tons of TiO2. Reserves of rutile found in the United States are estimated to be 1.8 to 2.1 million tons of TiO2. Other than occurrences in Florida and South Carolina, rutile is found either in small scattered bodies or in deposits where the mineral cannot be recovered economically by present beneficiation methods.

Jan 1, 1966

By J. P. Schde

The authors deal with nickel production and usage patterns, nickel's first-use and end-use, examples of nickel applications in modern technology, e.g., energy generation and conservation, environmental protection, the oil and gas industry, construction and machinery, food production, conservation and distribution, consumer durables and the like. A special section of the paper is devoted to new applications of nickel in the electronic industry, modern corrosion control and the building and construction industries. The need to defend traditional markets for nickel while striving to find new applications, is also stressed.

Jan 1, 1988

By T. E. Bernard

Occupying a refuge alternative (RA) is an accepted practice in mine fires and explosions when escape is not feasible. MSHA has promulgated a final rule on refuge alternatives that includes a recognition that thermal environment is an important consideration. To this end, an environmental index was specified. The question remains about how to test a refuge shelter to demonstrate that it meets the final rule. The analysis followed five activities: A. Provide an estimate of heat generated by an individual refuge alternative occupant; B. Evaluate the Steadman Apparent Temperature criterion of 95°F; C. Discuss simulations based on body temperature or skin temperature limits; D. Suggest method of simulating human heat generation during refuge occupancy; and E. Suggest alternative methodologies/criteria for evaluating heat and humidity survivability inside a refuge alternative.

Feb 27, 2013

"2.1. General Considerations and Properties2.1.1. IntroductionOur present knowledge of the platinum-group elements (POE) is extensive, the reason being two-fold. The elements have many uses and, moreover, they exhibit extremely varied chemical behaviour, depending on their state of oxidation and chemical environment. The present chapter reviews a selected body of material which is of particular relevance to mineralogy and geochemistry.Comprehensive treatises on the POE include those by Mellor (1956-1957), Gmelin (1938-1957) and Pascal (1958). The inorganic chemistry, particularly coordination chemistry, has been dealt with in works by Griffith (1967), Hartley (1973) and Livingstone (1975), and the analytical chemistry by Walsh and Hausman (1963), Beamish (1966) and Beamish and Van Loon (1972, 1977). Darling (1973) and Savitsky (1978) have reviewed the metallurgical properties and applications of the metals. Goldberg and Helper (1968) have reviewed the thermochemistry and oxidation potentials of POE systems, and Wagman et at. (1969) have also provided selected values of their thermodynamic properties. The geochemistry of the POE has been reviewed by Yushko-Zakharova et at. (1967), Cousins (1973), Cabri (1974), and Naldrett and Duke (1980).Platinum was used briefly as a coinage metal in ImperialRussia. Otherwise, the principal early use for platinum and its alloys was in the fabrication of chemically resistant apparatus. Subsequently, a large part of platinum production was utilized for catalysts in the sulphuric acid and ammonia industries. Platinum has been replaced by vanadium pentoxide in the manufacture of sulphuric acid, but, in recent times, catalytic upgrading of petroleum and emission control systems for automobiles have opened further huge markets for the metal. All of the POE find uses either as reagents or catalysts in the synthesis of organic compounds, e.g., in the Wacker process, which uses palladium chloride to catalyze the production of acetaldehyde from ethylene. There are, of course, a large number of specialized uses for the elements, particularly in alloys, temperature measurement devices, cancer therapy and so on."

Jan 1, 1979

By C. M. Kleemann

The paper describes the present milling practice at Western Mining Corporation Limited's new nickel mine at Kambalda in Western Australia. It details the crushing, autogenous grinding, flotation and spray drying circuits for the production of a nickel concentrate. It also indicates some of the metallurgical problems which have been encountered in concentrating this ore.

Jan 1, 1973

I N the introductory chapter to "Man and Metals," T. A. Rickard wrote "Five hundred thousand years ago the first footfalls of man's oncoming echoed down the corridors of time." This phrase has always appealed to me, not only for its resonance but because it seems to place in some perspective man's place in the cosmos. As we go about our daily occupations and as we meet here tonight, we must agree that we have come a long way slowly at first through the ages of change but with a quickening pace that has brought to man's know-ledge and use, within the last hundred years, more ideas, more material advantages, more opportunities and more comforts than were ever imagined or dreamed of in those long corridors of time. Looking back to the dawn of his-tory, a mere five thousand years ago, there is one aspect of the birth and growth of civilization that has particular significance for the miner and the metallurgist.

Jan 1, 1965

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By Peter Iovino

Unfortunately, I don't know the unit cost per cubic yard of treatment. I reflected on that yesterday and I don't think that we considered the use of micropiles. They could have been an option. The challenge may have been picking up some of the lateral load but I think the micropiles could have been installed on a batter and perhaps extended to rock. We could have considered them, but I do not believe we explored micropiles as an option for this project.

Feb 10, 2003

By H. D. Hunt

This paper which describes the milling practice of the Miami Copper Co. is one of a series being prepared by the United States Bureau of Mines. LOCATION The mine, concentrator, and other surface plants of the Miami Copper Co. are located near the town of Miami in the Globe-Miami mining district of Gila County, Ariz.

Jan 1, 1932

By Edwin M. Murphy

Methods are described for filling underground cavities remotely with dry material pneumatically injected through a borehole to seal openings, prevent air movement, and reduce subsidence; this often brings underground fires under control by limiting the access of air. Large-scale tests were made in the Bureau of Mines Experimental Coal Mine, Bruceton, Pa., in an operating mine, and in an abandoned Pennsylvania mine. Supplemental trials were made aboveground in galleries and in the laboratory. The parameters studied include horizontal and inclined passageways, obstructions in the entry, water leakage into the borehole, dry material, and grout and slurry mixes. The materials studied were fly ash, crushed and pulverized limestone, and sand. Best results were obtained with dry fly ash, though satisfactory seals were obtained with the other materials. When a borehole is dry and ends at an open void, casing is not necessary. If more than 5 gpm of water flows in the borehole, if the void contains loose debris, or if coarse material is injected, a material feedpipe should be inserted through the borehole. Fly ash was most suitable for remote filling because of its low angle of repose (8°) and its good flow characteristics. The depth of borehole through which the fly ash is injected has no appreciable effect on the filling operation.

Jan 1, 1968

By D. Nyungu

Despite observations of spalling and damage of mine excavation wall rock in the Bushveld Complex (BC) over the passage of time, there have been very few time-dependent or creep tests carried out in South Africa on rock, particularly on BC rock types. The research described in this paper deals with the investigation of stress and strain conditions influencing spalling of wall rock in BC mine excavations, and the influence of time on the tensile strength of several BC rock types. Time-dependent laboratory testing of BC rocks was carried out in indirect tension. The results show that the magnitude of the tensile strength of BC rock types is approximately 5% of their uniaxial compressive strength magnitudes. The average long-term uniaxial compressive strength of the BC rocks, interpreted from the axial stress-volumetric strain graphs, is 56% of the UCS value. The long-term tensile strength is shown to be less than 70% of the normal tensile strength. Extension strains at tensile strength failure ranged between 0.16 and 0.21 millistrain. Values corresponding with the long-term tensile strength are less than 70% of this range, namely, 0.11 to 0.15 millistrain. These results represent new knowledge, since such rock testing and analysis does not appear to have been carried out previously on BC rock types. Elastic numerical modelling was carried out to illustrate the extents of tensile stress zones and extension zones around of typical BC mine excavations. The models showed that large zones of extension strain can occur around BC excavations, and that the magnitudes of the extension strain can substantially exceed the critical values determined from the laboratory testing. The implication of this is that there are substantial zones surrounding BC mine excavations that will be prone to time-dependent spalling conditions and perhaps more significant failure.

Jan 1, 2014

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

By H. C. Gunning

Introduction The invitation to contribute a discussion on some of the broader features of the mineral deposits of our Cordillera seemed acceptable enough when presented several months ago. More mature consideration has impressed upon me the difficulty of making any constructive or very helpful contribution in the short time available and with my limited inspiration. Dr. Lang deserves our real gratitude for his general paper of nineteen pages at the beginning of the Volume. Into it, with the help of two diagrams and seven tabular summaries, he has packed a lot of useful information and has analyzed along several lines the data of the Volume's twenty-eight detailed papers on our mines and camps. He has added additional facts from his own knowledge of the region. I am sure that, like myself and the whole fraternity, he feels especially grateful to the eleven company geologists who found time to contribute detailed descriptions of mines they have studied. The Regional Situation With the Jubilee Volume and two recent publications of great value from the Geological Survey, we are more up-to-date on Cordilleran geology than we have ever been. But I would like to emphasize that we still have but fragmentary information. Brief study of G.S.C. Map 932A will illustrate this. Our knowledge of the Rocky mountains is limited to two narrow sections along the main railway lines, a somewhat larger area from the border north along the Mesozoic coal-bearing basins, and some reconnaissance along Peace river and the Alaska highway. There is some additional information on old maps, particularly those by G. M. Dawson, but it is very much of the 'exploratory' type. The other mapped areas are chiefly in the accessible region south of 'fifty-one', in the central part adjacent to and spreading north, recently, from the Canadian National railway, and along the edges of the Coast Range.

Jan 1, 1950

By Richard A. Rivell

This document is a users manual intended as a reference for personnel interested in the analysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The interactive procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures available include Gauss-Seidel and Newton-Raphson iterative techniques for the analysis of normal operation or balanced faults as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults.

Jan 1, 1980

Jan 1, 2001

By Allen B. Stanton, Parthiv Brahmbhatt, Michael Grimm, Stanley L. Worst

Constructing a circular shaft consisting of secant piles has its own complications which make it more difficult than typical drilled shaft construction. Add to that performing under low overhead powerlines and sitting inside of a 40-foot deep, 50-foot diameter shaft and it becomes more about logistics than the actual drilling. The complexities associated with the Romeo Arm Interceptor Segment 5 Lining project are the focus of this paper, delving into the details that made it work successfully.

Oct 1, 2022

By C Thompson, D Connelly

The history of mill liners has evolved over time and this paper tracks the changes and development of liner technology. It provides an overview of the primary types of liners, the design and the materials of construction. The design of a mill liner is driven by application, materials of construction, casting technology and handling issues. The choice of solid steel, grid liners, rubber or composites and magnetic liners is based on many factors.The methods used for monitoring wear and predicting eventual change out time are many and varied. The contribution of discrete element modeling (DEM) analysis in predicting wear profile is discussed.Mill trajectory and DEM software programs are used with great effect to predict the effect of lifter height, face angle, high low lifters or mill speed. In the field, trial and operational experience is used or improvements/design concepts at one operation are applied to another. Broken mill lifters, accentuated wear and other problems can be better understood using hardness testing, chemical analysis and photo micrograph analysis of pearlitic or martensitic structure along with fracture face observations. This forms a part of the typical root cause analysis. However given correct and sound liner and lifter, feed and discharge design media selection, and materials of construction, the majority of premature liner or bolting failure is normally attributed to incorrect operational methods such as excessive high ball to feed ratio, incorrect mill speed relating to lifter ball throw, incorrect media selection, "tramp" material entering the mill charge from upstream or recirculating process and understanding the specific mill operation in question.It is hoped that this paper will benefit mill operators who are faced with challenges of improving wear life and at the same time optimizing mill throughput and performance.CITATION:Connelly, D and Thompson, C, 2013. The selection design and application of mill liners for large wet grinding mills, in Proceedings MetPlant 2013 , pp 133-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

By K. J. R. Ford

"Significant advances in mining and metallurgical operations have occurred over the last two decades, to define ore bodies via geological mapping, mineralogical analyses, geostatistical models and resource reserve modeling. Metallurgical process measurement, controls and modeling have also significantly progressed, with advanced instrumentation, control software, data capture systems and simulation tools. This progress together with development of the science of geometallurgy has allowed geologists, mineralogists, miners and metallurgists to start working together to define geometallurgical ore units and link these to mine planning and projected metallurgical performance. However, application of full geometallurgical programs into existing mine-processing operations or into new “greenfield” projects has been slow. This is mainly due to higher costs, limited dedicated technical resources and little or no corporate leadership. Additionally, life-of-mine cash flow models, the “dollars”, have been largely driven by ore tonnage rates, pay-metal grades and fixed pay-metal percentage recoveries, with few or no geometallurgical parameters included.Here defined, the “electrons” represent intrinsic ore characteristics embracing chemical composition, mineralogy, gangue components and their associated fundamental metallurgical processing phenomena. With its ever expanding treasure chest of measurement and modeling tools, geometallurgy paints a much clearer picture of the “electrons” for the geologist and metallurgist. But to fully understand and realize the real net value of ores over the life of a mine, a comprehensive link of “electrons to the dollars” is essential. Intrinsic characteristics of geometallurgical ore units are by definition linked to their metallurgical processing, but importantly need also to be related to operating costs, capital requirements and revenue.This paper discusses this important linkage under topics of ore geology and mineralogy, metallurgical processing, waste disposal, environmental issues, metal refining, project engineering and lifeof- mine models. Topics are illustrated by multi-metal references and by case examples from gold ore heap leaching and manganese ore smelting projects. 1"

Jan 1, 2013