Search Documents

A Seismic Hazard Scale (SHS) has been developed to provide a practical seismic hazard assessment tool applicable to mine site personnel. It has been applied to seismic data sets from numerous Western Australian mines. The SHS is applicable when quantifying seismic hazard on a mine wide scale, on a mining block scale, and on a local cluster-by-cluster scale. Spatial mapping of variations in seismic hazard is a particularly powerful application of the scale. The SHS is sensitive to temporal increases in seismic hazard. It has also been shown that the SHS can be applied to estimate seismic hazard when seismic monitoring data are not available. The SHS is a simple derivation of the Gutenberg-Richter relation. There are assumptions and limitations to the SHS that need to be considered when applying it to mine seismicity data.

Jan 1, 2004

By D. H. Desy

The Bureau of Mines studied the properties of copper that had been oxide dispersion-strengthened with 2 vol pct of either yttria or alumina. Compounds of copper and aluminum or yttrium, coprecipitated from aqueous solution, were converted to oxides; the copper was reduced, compacted, sintered, and extruded. For the resulting copper-dispersoid composites, room temperature tensile properties after annealing in hydrogen, elevated temperature tensile and stress-rupture properties, and electrical conductivity were determined. Compared with oxygen-free copper, copper-2 vol pct alumina or yttria had improved strength after annealing between 400° and 1,000° C, and improved elevated temperature strength, with little loss in electrical conductivity.

Jan 1, 1969

By M. Leva

WITH the development of new processes for the production of synthetic liquid fuels, an extensive literature search was undertaken to uncover fundamental relationships between fluid and heat flows and the operating variables of new types of converters. Examination of published correlations revealed that considerable uncertainty existed in the correlation of the operating variables of such equipment with the pressure drops which could be expected through packed and fluidized systems; correlations proposed in the literature differed from each other frequently by as much as 75 to 100 percent. Because new processes, especially more recent modifications of the original Fischer-Tropsch process, must compete with old, firmly established processes on the basis of unit product cost, the pressure-drop correlations in the literature were considered to be too inaccurate for use in calculating the energy required to pass fluids through packed beds. The following study was begun in 1946 to develop correlations that would be suitable for the design of new equipment in which fluids are brought into contact with granular materials. To arrive at general relationships, systems were chosen that did not involve chemical reactions, and a, particular effort was made to give the correlations only in terms of quantities that are ordinarily available from general process and design specifications.

Jan 1, 1951

By William O. Vanderburg

Tis paper describing the mining practices at the Cold Springs mine of the Wolf Tongue Lining Co. at Nederland, Colo., is one of a series of similar papers prepared by the Fureau of kines on mining practices, methods, and costs at various mines in the United States. The writer acknowledges the assistance of William Leach and William T. Todd, manager and mine superintendent of the Wolf Tongue Mining Co., respectively, in the preparation of this paper.

Dec 1, 1932

By A. C. Fieldner

The past full year of war has increased greatly the demand for virtually all kinds of fuel, and the Bureau of Mines research and service facilities have been extended to meet these unprecedented requirements. Liquid fuels, such as aviation and motor gasolines, are fundamental to modern warfare. Bituminous coal and anthracite are needed, not only to servo the expanded industrial program for which coal normally is used but also to replace natural gas, wherever possible, and fuel oil in the Eastern States, New England, and the Pacific Northwest. Railroad transportation with energy derived from coal is replacing much of the motor-vehicle transportation that has been stopped or curtailed to conserve rubber. Pulverized coal hoe been sound to be a satisfactory and cheaper substitute for fuel oil in metallurgical heating furnaces. Celloidal fuel - a mixture of coal dust and oil - may offer a partial substitution for curtain coal-burning equipment. Several industrial experiments have been made with this type of fuel. The expansion of the steel industry in connection with the war program has required a corresponding increase in the production of metallurgical coke and its associated byproducts - light oil, tar, ammonium sulfate, and surplus gas. If the war is of long duration and new reserves of petroleum are not discovered, wartime trends from fuel oil to coal probably will not be reversed.

Jan 1, 1945

By Sidney Katell

This report, covering the period January 1965 through December 1965, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the seventh in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are From the following sources:

Jan 1, 1966

By Sidney Katell

This; report, covering the period January 1965 through December 1965, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the seventh in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal.3 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. Oil and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1966

By Bruno Deves Flores

O presente trabalho tem como objetivo investigar a influência da adição de carvão vegetal e do seu tamanho de partícula na reatividade do coque. Para isso, um carvão vegetal de eucalipto foi adicionado a um carvão médio volátil americano em três teores (3%, 5% e 8%) e em duas faixas granulométricas distintas (abaixo de 1 mm e entre 3 mm e 4 mm). O carvão individual e as misturas de carvão/carvão vegetal foram carbonizados em um forno de escala laboratorial (1 kg). A reatividade dos coques produzidos e do coque de referência foi avaliada e comparada usando análise termogravimétrica. Também foram realizadas análises morfológicas através de microscópio óptico e eletrônico, usando amostras antes e após os ensaios termogravimétricos. Baseado nos resultados, a influência da introdução de carvão vegetal na reatividade do coque foi analisada e discutida neste trabalho.

Aug 1, 2018

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013

By Open-Hearth Steel

We have a very high-powered organization up here this morning, headed by Kenneth C. McCutcheon, general superintendent of the Ashland Division of the American Rolling Mill Company, and L. A. Lambing, superintendent of the open-hearth and Bessemer departments of Jones & Laughlin Steel .corporation of Aliquippa, Pa., representing the open-hearth men. Also, we have P. F. Dolan, assistant general manager of the Maryland plant of Bethlehem Steel Company, of Sparrows Point, and Harry E. McDonnell, superintendent of blast furnaces of Weirton Steel Company of Weirton, W. Va., representing the blast-furnace section.

Jan 1, 1940

By K Ringwood, J Cummings, C J. Moran

The development of a water accounting framework that enables consistent and contextual reporting of minerals operationsÆ water use, represents a key sustainable development objective that many Australian minerals companies have committed to. A future water accounting framework will require: key terms and definitions for water metrics for use in the Australian minerals industry that are consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current regulatory requirements and voluntary approaches were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (eg water loss through evaporation). The adopted terms and definitions typically require a combination of empirical and estimated data. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites, selected to test a variety of commodity and biophysical situations. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and following a period of stakeholder engagement and third party review, is being refined as a first step towards developing nationally consistent water use reporting for the Australian minerals industry.

Jan 1, 2009

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By Immo H. Redeker

Introduction In October of 1961 Texas Gulf Sulphur Company contacted the Asheville Minerals Research Laboratory, of the North Carolina State University, and requested assistance in the development of a phosphate ore body in Beaufort County. The main: objectives of the work at Asheville were defined as follows. The Laboratory should try to determine on the basis of drill core samples, submitted by Texas Gulf Sulphur Company, the highest grade of phosphate concentrate that could be obtained with high recoveries from North Carolina ore, the thickness of the ore body that could be treated economically in one section, and the quantity of concentrate that could be obtained per acre. The results should be compared with data obtained from the treatment of Florida ores. It was important to use mineral preparation methods during the initial laboratory work that could be verified later by continuous pilot plant operation and could be scaled-up for a commercial plant. The writer was in charge of the project at the Asheville Minerals Research Laboratory and participated in the development of one of North Carolina's greatest mineral resources from the first drill core examination to the production of the first poundage and tonnage quantities of flotation concentrates. The Lee Creek phosphate mine and mill was put in operation in early 1966 and can produce three million tons of phosphate concentrate a year. Sulfuric- acid, and phosphoric acid plant, diamonium phosphate plant and triple super phosphate plants came on stream in 1967; at that time they were the world's largest. Now that a phosphate industry has been established in the State, it]

Jan 1, 1971

By John A. Hudson, Xia-Ting Feng, Joseph S. Y. Wang

Evolution over decades and progress over last five years have been made in many topics of interests to rock mechanics, geosciences, physics, and multi-disciplinary interactions in underground research laboratories and development facilities, as well as in underground energy recoveries and environmental assessments. Rock mechanics and geotechnical engineering advances are associated with quantifications of disturbed/damaged zones and rock alternation and bursting processes and creation of underground spaces and accesses associated with deepening of shafts and lengthening of tunnels. Geophysics and earth sciences advances are associated with continuing collections of seismic, electromagnetic, and gravitational data and conducting various thermal, hydrological, mechanical, chemical, and biological investigations, both separately, simultaneously, and in different coupled ways. Astroparticle and underground physics advances are associated with many long term experiments to detect rare events and needs for increasing larger and deeper halls to accommodate next generation detectors, shielings, and isolations. There are also increasing interesting in underground settings to explore multidisciplinary and inter-disciplinary sciences and technologies. Energy and environmental sciences and assessments have evolved from traditional oil and gas focuses to recent activities associated with green resources and alternative recovery/disposal strategies. The evolution and progress of these interdependent and related fields are discussed in this quadrennial Congress.

Jan 1, 2015

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

By Craig S. Compton

The failure of the immediate roof or "roof skin" between installed primary and secundary roof supports causes hundreds of injuries and, on average one or two fatalities each year in U.S. underground coal mines. Conventional roof supports cannot cover enough roof area to adequately control these relatively small, but very dangerous rock falls. The 2006 Mine Safety and Health Administration (MSHA) accident database lists a total of 542 ground fall injuries, including 10 fatalities. An analysis of the database suggests that 434 of the injuries and three of the fatali­ties can be attributed to roof skin falls (See Figure 2). The key to controlling falls of the immediate roof or roof skin is maximizing the area of roof coverage ilnd confining these relatively small loose rocks. Roof screen offers maximum coverage of the immediate roof. Depending on the size and configuration of the screen panels, coverage of up to 100% of the roof area is possi­ble. Screen also offers a first line of defense for machine operators working in the face area by confining or deflecting small rocks that can come loose during mining or roof bolt installation. Figure 1 shows an example of the protection screen provides dur­ing bolt installation. Although the benefits of screen are well-known, mining com­panies in some areas of the U.S., mainly Northern Appalachia and the Illinois basin, are not convinced that roof screen is the best tool for dealing with roof skin control issues. The logistics of material handling, possible ergonomic injuries to workers, and the costs associated with installation are delaying the acceptance of screen as an on-cycle roof support tool. Other mines however, have concluded that installing roof screen can be cost-effective when compared to the cost of lost time accidents, training of replacement workers, or returning to already developed entries for the cleaning and rebolting process.

Jan 1, 2009

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983

By J. B. Mitchell

Many of the pre-production and plant startup problems that we regard as inevitable are actually caused by poor organizational methods. Traditional methods of organization can be modified to provide clear definitions of responsibility, continuity and depth of involvement of key personnel in order to overcome these problems.

Jan 1, 1966

By V. J. Lynch, A. L. Peyton

"INTRODUCTION AND SUMMARYThe Brewer mine, near Jefferson, Chesterfield County, S.C., was originally operated as a gold mines as late as 1890 this mine was reported to have been one of the large gold producers in the southeast,Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered by Pardee and Parks. 3/ of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.During the 1940's the Chemical Engineering Branch of the Tennessee Valley Authority and the Electrotecbnical Laboratory of the Bureau of Mines at Norris, Tenn., investigated topaz from the Brewer mine to determine the possibilities of its use as mullite and for the production of calcium fluoride.From July 1950 through. April 1951 the Bureau of Mines conducted a diamond-drilling project at the Brewer mine to determine the grade and extent of the topaz deposits. Ten diamond-drill holes, totaling 2,344 feet, were completed, and 231 analyses of core samples were made during the course of the project.This report presents factual data relating only to the diamond-drilling project, The placer deposits on the Brewer property were previously investigated by the Federal Geological Survey 4/."

Aug 1, 1953