Search Documents

By John T. Cumberlidge, Frederic M. Chace

Nickel-bearing saprolite developed during the early Tertiary over a northeast trending ultramafic body of Jurassic age near Riddle in southwestern Oregon. The principal nickel mineral is garnierite, but other complex nickel minerals may be present. There are two main ore bodies, an upper (older) one associated with the Klamath peneplain, and a lower (younger) one on the Sherwood peneplain. Saprolite constitutes the bulk of the ore and was probably derived from peridotite and dunite through chemical decomposition by downward percolating meteoric groundwater. Decomposition took place by net loss of MgO, SiO2, and Fe without a change in volume. Faults and joints provided permeable zones which localized saprolite development, and faulting may have helped preserve some ore from loss by erosion. Garnierite-chalcedony boxwork ore was deposited by meteoric groundwater along faults, joints, and at the level of former water tables. Boxwork ore is entirely supergene, the chemical constituents having been derived from higher in the soil profile. The saprolites show evidence of both supergene and residual enrichment in nickel. Red and yellow soil occurs as a capping over saprolite and boxwork, and was derived from them by chemical and mechanical decomposition. The present deposits are probably truncated remnants of a formerly thicker and much more extensive deposit which probably included laterite at the surface. The deposits started to form in the early Tertiary due to deep chemical weathering under sub-tropical to warmtemperature conditions. Early Tertiary ero~ion surfaces of low relief probably contributed to the predominance of chemical weathering over mechanical erosion. Alteration under present climatic conditions favors the formation of soil from saprolite rather than the formation of new saprolite from peridotite.

Jan 1, 1968

By Mark R. Pettitt

The charter of this investigation was to identify and promote the application of noise control technology to future longwall mining machinery. Intensive noise and vibration data were acquired on a typical longwall shearing machine, and the highest noise levels were shown to radiate from the cutter drums. Shearing machine cutter drum noise control techniques that take advantage of the nature of the dynamic forces generated during coal cutting were developed. These include both structural redesign and force isolation techniques. A reduced noise cutter drum was developed that achieved a 5 to 6 dBA system noise reduction at the operator's position. Its operational performance was verified by a six-month long in-mine test. It was evident from the data that additional noise reduction could be achieved by treatment of the shearing machine hydraulics. Noise control of secondary sources was also investigated. A method of reducing full or empty stage conveyor noise (and continuous miner conveyor noise) by 5 to 10 dBA was demonstrated through isolation techniques. Underground mine durability testing, however, is yet to be demonstrated.

Jan 1, 1986

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

The following pages discuss the objectives, the background, the scope and a statement of the problem of the study of methods to improve the pillar extraction practices in underground coal mines. 1. OBJECTIVES The objectives of this project were: ? to determine the principal factors contributing to high accident frequency and severity in both conventional and continuous mining operations; ? to compare and evaluate the safety aspects of the "open end" and "split and fender" systems of pillar mining; to establish basic data required to decide what constitutes an adequate pillaring plan that will optimize efficiency, recovery, and safety; ? to determine what measurements or information should be collected, (e.g. roof sag, pillar stress,) to make on-the-spot judgment of impending roof or pillar collapse; ? to make recommendations to improve existing methods or to insure proper techniques are implemented, and ? to suggest areas where additional studies or new research may be of value.

Jan 1, 1975

By Madan M. Singh

This section is unique to the Handbook in that it is the only section that deals with underground excavations for nonmining purposes. The editors were of the opinion that the section should be incorporated because the subject matter covered by the chapters is closely related to mining, and many mining engineers are currently involved in these activities. As we enter the decade of the 1990s activities in this category will increase, enhancing the relevance and utility of the material discussed. As the population increases, especially in metropolitan areas, the necessity to go underground will be greater. At the present time, not only are subsurface shopping malls and pedways connecting buildings becoming commonplace, but structures as diverse as the Civil and Mining Engineering Building on the University of Minnesota campus, a road-and-fleet maintenance facility in Multnomah County, OR, and even an ice cream parlor (Dairy Queen) in northern Wisconsin have been constructed underground. Placing utilities below the surface has numerous advantages and is now customary. Rapid transit and highways through tunnels in urban areas have been the norm for many years, but subterranean stormwater reservoirs, power plants, industrial warehouses, and food storage silos are relatively new innovations. The philosophy of underground defense installations is ancient, but their requirements and designs have trans-formed radically as technology advances. The use of under-ground space for disposition of wastes is modern, since it is recently that environmental concerns and waste disposal costs have assumed increased significance.

Jan 1, 2008

By Paul M. Tyler

The literature on radium is already voluminous, but mcuh of it is too technical to be intelligible to the average reader, and there is no single publication that covers certain economic features of the radium industry. As a result of the renewed interest in the possibilities of domestic carnotite deposits a number of requests have been made to the Bureau of Mines for information, more particularly with reference to the business aspects of the industry. In order to meet this apparent need, the present paper has been prepared from material available in the files of the bureau. The technical data are compiled from various sources and are believed to be reasonably dependable, but the attempt has been not so much to achieve meticulous scientific accuracy as to brim; together facts of industrial significance and popular interest. GENERAL DESCRIPTION Radium is a brilliant white metal that melts sharply at about 700°C. and volatilizes appreciably at that temperature. With an estimated specific gravity of nearly 6.0, it is more than twice as heavy as aluminum and 25 per cent lighter than irons. Although it has been isolated in its metallic state, it is not used in that form, partly because it tarnishes rapidly even in dry air (forming a nitride), partly because of the greater expense of reducing it to metal, and partly because of the difficulty of dealing with such minute quantities of material. It is used always in the form of its compounds, the most important of which from the vie point of utilization are the bromide, chloride, and sulphate.

Jan 1, 1930

By G. L. Oldright

As a rule, the usual zinc retort smelter fired with natural gas made its own burners, of which there might be 300 per block, out of standard pipe fit-tings. The gas was discharged through a feeder pipe at various distances into a cylindrical horizontal "blow hole" through a pillar block and thence into the furnace; the best location of this gas-feeder pipe was at the horizontal central axis of the blow hole; the side entry into the blow hole usually was used. The air entered the same blow hole behind the gas, through a short nipple, in the inner end of which was a constructing orifice in a clay plug; in this ,work cone-shaped funnels of various lengths also were used. Even with the air and gas correctly proportioned to each burner, small differences in their dimensions were found to influence greatly the temperatures reached, their uniformity, and consequently the percentage of zinc extracted. This fourth paper of a series on cooperative work in the zinc retort plants of the Eagle-Picher Mining & Smelting Company discloses the methods and principles followed in approximating closely the optimum dimensions for various burners, with examples from experimental and commercial furnaces showing the interrelation of such dimensions with combustion and temperatures in the furnace.

Jan 1, 1948

A symposium was held on January 30 and 31, 1973, at Pittsburgh, Pa., to review the state-of-the-art in designing and utilizing diesel-powered equipment in underground mining. The Health and Safety Activity of the Bureau of Mines sponsored the symposium with major assistance from the following four participating organizations: The American Mining Congress J. Allen Overton, President The United Mine Workers of America Arnold R. Miller, President The National Independent Coal Operator's Association Cloyd D. McDowell, President The Bituminous Coal Operators' Association, Inc. Guy Farmer, President Seventeen papers were presented during four half-day sessions devoted to the general subjects of the diesel engine, the place of the diesel in underground mining, health protection using diesels underground, and maintaining safety of diesels underground. Eleven of the speakers were from industrial organizations here and abroad; one represented the Provincial Government of Nova Scotia; two were with the Department of Health, Education, and Welfare; and three reported on Bureau of Mines work related to diesels.

Jan 1, 1975

By Bernadette C. Michalski

Mineral raw materials, labor, capital, and technology form the basis of industrial production. The augmentation of one or all of the elements--labor, capital, and technology--will result in industrial growth. Thus, an increase in the labor force would increase output. A similar result would be achieved by expanding capital investment and supplying labor with more equipment. Finally, industrial growth can be achieved by introducing more productive methods and techniques born of technological advancement. The Soviet Union has employed these elements in many patterns to catapult from an agricultural to an industrial economy in four decades. The early history of the Soviet Union was marked by limited capital and borrowed technology, forcing the Soviets to concentrate on an abundant labor reserve to support the industrial program. The source of this reserve was the rural population. In [1928], 80 percent of the working population was employed in agriculture. This figure dropped to 43 percent by 1956, whereas industrial employment in the same period increased from 8 to 31 percent.3/

Jan 1, 1960

By Herbert H. Einstein

This report contains the documentation for 11 computer programs representing the entire computer documentation for the eight-volume report entitled "Risk Analysis for Rock Slopes in Open Pit Mines." A detailed summary of the programs is included.

Jan 1, 1979

By F. De Lucio

Para la aplicación de la instalación de un sistema de relleno hidráulico es necesario evaluar las funciones que el relleno debe contener y determinar si el material a usar cumpla con las funciones especificadas. En ese sentido, el objetivo del texto presenta una interpretación científica sobre tal método para especificar las funciones que el relleno deba cumplir y la metodología experimental adecuada que evalúe cuantitativamente a un relleno hidráulico.. Asimismo, se describen sus propiedades estructurales como la densidad relativa, reducción de volumen y estabilidad de tajeos contínuos, así como los métodos indirectos para inferir dichas propiedades y las posibles consecuencias secundarias que pueda generar el empleo de relleno hidráulico.

Nov 20, 1972

By Joseph Gambogi

In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of futile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium. In this paper, we discuss all aspects of the titanium industry from ore deposits through extraction to present and future applications. The methods of both primary (mining of ore, extraction, and purification) and secondary (forming and machining) operations will be analyzed. The chemical and physical properties of titanium metal will be briefly examined. Present and future applications for titanium will be discussed. Finally, the economics of titanium metal production also are analyzed as well as the advantages and disadvantages of various alternative extraction methods.

Nov 26, 1999

By E. C. Westman, W. R. Thomas, W. J. Conrad, A. J. R. Russell

"Understanding ground control problems continues to remain a focus of the mining engineering community. To aid mine operators and engineers in identifying and responding to ground control issues, the Ground Observation System (GOS) is being developed. The GOS is an integrated, web-based graphical user interface that displays ground response data collected wirelessly from an underground mine. It presents data in an intuitive manner to assist mine personnel, who are on- or off-site, in quickly identifying hazardous areas. Geotechnical instrumentation will be connected to wireless transmitters that will relay data in real-time to a surface computer that stores the information in a database. The GOS website will then display the geotechnical data in graphical and tabular forms, as well as in conditionally formatted mine maps. Data from each measurement device will be able to be viewed in its entirety or within a time interval, and can be downloaded for further analysis. The ability of the GOS to quickly interpret and communicate mine hazards to personnel of varying technical ability should prove to be a useful tool in understanding ground control and thus improving mine safety.INTRODUCTION Computer-based data information centers that convey operating parameters and conditions are prevalent in modern underground mines. Today’s systems are popular in showing ventilation controls and monitoring equipment performance (Jyothi & Meena 2013). In ground control monitoring, Conover, Ross, and Bigby, 2010 have installed a wired telltale roof monitoring system that sends roof displacement data every ten minutes to a computer on the surface. The computer receives, stores, and displays the data in real time. Data can also be viewed remotely through a password protected internet connection. Additionally, an internet connection allowed for remote updates to the system which streamlined software development and maintenance by eliminating travel (Conover et al., 2010). Currently, no such system beyond Conover et al.’s design has been accomplished. The Ground Observation System (GOS) is being developed to fill the void of real-time geotechnical monitoring in underground mines. A wide array of data will be transmitted wirelessly and broadcasted to on- and off-site mine personnel through the internet. The GOS will incorporate geotechnical data from roof deformation, borehole scratch testing, photogrammetry, and seismic monitoring into one interface, all while achieving permissibility for the use in gaseous mines. As a result, a comprehensive view of rock movement due to mining will be available. The overall purpose of the GOS is to deliver warnings; to ensure reliable data is relayed to personnel for the identification of potential ground failures, provide mine engineers information to design more stable mines, and assist with further geotechnical research."

Jan 1, 2015

Jan 1, 1988

By T. A. Rickard

An educated man is distinguished neither by his clothes nor by his knowledge; he is replarkable not for the things he says, but for the way he says them. You cannot even stand with him under an archway in the rain without finding him out. He may talk only of the weather. His words and his phrases alike may be simple. -at distinguishes him is the arrange- ment of his words; however desultory his talk, it will be method- ical; he has habituated himself to foreseeing the part to be played by each word he uses and the place to be taken by each sentence he utters. On the other hand, the uneducated man, though shrewd and well-informed, will relate facts and events as they recur to him, generally in disorder; in his effort to recollect and in his attempt to rectify forgetfulness he will pause irregularly, filling the intervals with meaningless phrases, such as "and then ", "and: so ", or 'said he to me", "said I to him"; and even the contipuous parts of his story will be told confusedly-because he has not learned the proper use of words.* My own experience as an editor of technical manuscripts has taught me that the misuse of 'that' and 'which' is a fruitful cause of obscurity and confusion. The relative pronouns have distinct functions, and no writer can express himself clearly until he has learned to discriminate between these I functions. For example:

Jan 1, 1931

By H. K. Najarian

AT Josephtown, Pa., on the south hank of the Ohio River about thirty miles northwest of Pittsburgh, is the Josephtown electrothermic zinc smelter, which operates as a custom smelter receiving both domestic and foreign concentrates. Constructed in 1930, the plant was designed to produce zinc oxide and to process 124 tons per day of zinc concentrate obtained mainly from the Company's New York State mines. Zinc condensing equipment was developed in conjunction with the St. Joe electrothermic. furnace and commercial production of zinc metal started in 1936. Expansion of the plant and equipment during 1939 and 1940 brought the processing. capacity to upwards of 300 tons of concentrate per day; and the plant operated at peak capacity during the war years, earning the Army-Navy "E" award and three subsequent stars. A postwar plant expansion is now under way, designed to increase the capacity to 500 tons per day of concentrate, with an estimated daily production of 160 tons of zinc metal of various grades, about 100 tons of zinc oxide, and 425 tons of sulphuric acid as major products.

Jan 1, 1947

By Mishark Nnabuchi

A heterojunction of PbS - CuS thin film has been grown on glass slides by SGT. The films were annealed for 1hr at temperature of 373K and 423K respectively. The optical properties were characterized using a UNICO UV - 2102 PC Spectrophotometer at normal incidence of light in the wavelength range of 200 - 1000nm. The minimum percentage transmittance was observed to be 34% for sample A and 25% for sample B within the same optical region. The band gap energy was determined from the spectra to be 2.05eV for sample A and 1.85eV for sample B which gave a band shift of 0.20eV. It can thus be concluded that the optical properties of the films within the VIS - UV - NIR can find application in solar thermal technology, particularly as antireflection coating, window materials and as good materials for selective solar cell fabrication.

Jan 1, 2010

THE Synthetic Liquid Fuels Act (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Federal Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation,3 the Fischer-Tropsch synthesis,4 and nil stifle.5 The. Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because anal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form Will Ire valuable. The material will he presented in three parts. as follows I. United Stares Patents. II. United Kingdom, Australian, Canadian, and South African Patents. III. Other Foreign Patents. Part I appeared in early 1960. Part II follows.

Jan 1, 1962

By Joseph M. Kurtak

The Bureau of Mines (Bureau) and the U.S. Geological Survey (USGS) conducted a 4-year (1979-1982) mineral assessment study of the Chugach National Forest (CNF), Ak, as part of the Roadless Area Review and Evaluation (RARE II) Program. The USGS remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. This report describes the results of Bureau work in the central 790,880 acres of the Forest. Copper, with by-product zinc, silver, and gold, has been the major metal produced from the study area as well as from the entire Chugach National Forest. The majority of the copper deposits are concentrated within basaltic rocks on Knight Island but the major producers are hosted by sedimentary rocks on Latouche Island. Approximately 182.6 million lb of copper, 1.5 million oz of silver, and an unknown but substantial amount of gold were produced during a 30 year period. Currently no mines in the area are producing. Inferred, indicated and measured reserves having mineral development potential total 4.6 million tons, with weighted average grades of 1.6% copper, 0.30 oz silver/ton, and 0.04 oz gold/ton.

Jan 1, 2011

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951