Search Documents

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By McHenry Mosier

Mechanical loading, adopted long ago in open-pit, coal, and non-metal mines, was not used extensively in underground metal mines until the World War. In less than a decade it became standard practice in underground work in many mining districts. In 1924 the Missouri School of Mines and Metallurgy, in cooperation with the Federal Bureau of Mines, published a bulletin entitled "Mechanical Underground Loading in Metal Mines," which was prepared by Charles E. van Barneveld, mining engineer, Bureau of Mines.

Jan 1, 1940

By Francisco Alberto Marreiros da Rocha Filho

A corrosão é um fenômeno que está intimamente ligado à integridade dos metais e de suas ligas. Esta ocorre de diversas formas, uma das principais é a corrosão localizada na forma de pites, objeto de análise desse estudo, que visa estabelecer um comparativo entre as curvas de polarização cíclica de algumas ligas ferrosas e não ferrosas, ensaiadas em solução de NaCl 0,6 M, mostrando a agressividade que a solução exerce sob cada uma das ligas. Os materiais analisados nesse estudo foram os aços inoxidáveis AISI 304, AISI 444, super duplex ASTM A890/A890 M Grau 6A, o aço carbono AISI 1030, o alumínio comercialmente puro, o cobre eletrolítico e a liga zircaloy- 4. Inicialmente foram medidos os potenciais de corrosão (Ec) de cada liga através do monitoramento do potencial de circuito aberto. Foram realizados os ensaios de polarização potenciodinâmica cíclica em cada liga, comparando o aspecto superficial antes e depois do ensaio através de micrografias óticas, possibilitando que fossem observadas as diferenças entre cada material quanto à resistência à corrosão por pites. Observou-se que algumas ligas não apresentam passivação como o caso do alumínio comercialmente puro, e outras apresentaram regiões passivas e histereses bem definidas, ficando evidente que, dentre as ligas analisadas, o aço inoxidável super duplex ASTM A890/A890 M Grau 6A apresentou os melhores resultados frente aos efeitos agressivos dos íons Cl- presentes na solução, sendo o menos suscetível à corrosão por pites.

Aug 17, 2017

By Jorge Nelson Rivera Guillén

"La tierra es una unidad de un complejo astral que se observa desde la antigüedad en sus aspectos exteriores y su dependencia del sistema solar. En ese sentido, el presente texto señala la génesis y evolución de los minerales comprendido en la tierra a través de cuatro libros denominados ""Los misterios del planeta tierra"", donde se mencionan los aspectos tectónicos preliminares y preparatorios para la disgregación de la Pangea Nueva, cuya “lenta explosión” ocasionó la separación de las placas tectónicasy la acción de fuerzas distensionales que actuaron sobre los fragmentos que generan desequilibrios barotérmicosinternos y la formación de zonas magmáticas y metalizaciones."

May 1, 2015

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905

By Samantha Smith

Nautilus Minerals (Nautilus) is following the lead of the petroleum industry as it strives to tap vast offshore resources. Planning is well underway for the Solwara 1 Project in the Bismarck Sea, Papua New Guinea (PNG) to recover high-grade seafloor massive sulphide deposits in 1600 m water depth. The deposit contains an average copper grade >10 times higher than a typical land-based porphyry copper mine. The high grades combined with a relatively small amount of overburden ensure the Solwara 1 Project will have a significantly smaller physical footprint than its land-based counterparts. Offshore minerals production also has the advantage of minimal social disturbance. Nautilus is dedicated to setting a high environmental and social responsibility standard. Nautilus recognises the importance of transparent and inclusive stakeholder engagement and has taken a proactive approach to involve as many key stakeholders as possible. One of the first steps in the permitting process in PNG is the preparation of the Environmental Inception Report, which describes the project, its envisaged impacts and the proposed studies for the Environmental Impact Assessment (EIA). Local (PNG-based) and international environmental scientists, anthropologists, NGOs and other experts were involved in the definition of studies conducted for the Solwara 1 EIA and a team of world-leading experts was involved with carrying out the studies, culminating in the preparation of the Environmental Impact Statement (EIS). To ensure transparency, collaborating researchers are free to publish their findings. Following its submission, the EIS was made available for public review and public hearings were held at several locations. The EIS has also undergone a rigorous independent review by PNG government-engaged consultants. Outside the permitting process, Nautilus works alongside government officials to carry out ongoing community consultations. Information dissemination and feedback acquisition has also occurred through the Nautilus website and attendance at a number of international conferences, workshops, and meetings. This paper will outline the leading edge approach Nautilus has taken in completing the environmental impact statement for the world?s first deep seafloor copper-gold mine. In addition, this paper will review the permitting process and the government and stakeholder engagement undertaken as part of Nautilus? desire to ?do it right? in this exciting new industry.

Jan 1, 2010

By Kenneth D. Winters

This Bureau of Mines report presents a Fortran IV computer program for the structural analysis of (1) protective canopies used in underground mines to protect equipment operators from roof falls and (2) rollover protective structures (ROPS) used in surface mines to protect equipment operators during vehicle overturn accidents. The program, entitled PLASTIC CANOPY, permits rapid and inexpensive calculation of the ultimate strength and deformation characteristics of a canopy for a variety of static loading conditions. The structure is modeled as a series of interconnected beam and/or plate elements. Stresses in, and displacements of, each structural element are computed and printed out at the yield strength of the canopy, at several intermediate load levels between the yield and ultimate strength of the canopy, and at the ultimate strength of the canopy. Other features of the program include prediction of buckling of a beam member under combined axial compression loading and bending, plotting of the input geometry of the structure, and plotting of the deformed shape of the loaded structure. Program description, input instructions, program listing, and four example problems are included.

Jan 1, 1979

By Felipe De Lucio Pezet

El presente texto señala las formas más eficaces de producción, donde no haya mayor consumo de mano de obra con menor incidencia directa en el tonelaje minado. Por ello, la modificación de las operaciones (mantenimiento de labores de acceso, avance en chimeneas; relleno; desarrollo de minas), conlleva un mejor productividad. Asimismo, la transferencia de tareas de operaciones no directamente ligadas a la producción hacia operaciones directamente productivas, permite un mejor uso de la fuerza laboral y reduce el costo de producción y aumenta la productividad.

Nov 1, 1972

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Ohio County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of-coal in place, are estimated at 365 million short tons as of January 1, 1954. Of this total, 356 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Thompson Júnior Ávila Reis

Neste trabalho, a microscopia de força atômica foi empregada para estudo da evolução da fragilização a 475ºC em um aço inoxidável lean duplex. Para tal, amostras deste aço foram submetidas a tratamentos isotérmicos com duração variando entre 1 e 100 horas na temperatura de 475ºC. Ensaios de tenacidade ao impacto e de dureza foram realizados para confirmar a ocorrência da decomposição da fase a. Posteriormente foram realizadas análises no microscópio de força atômica. Os ensaios de tenacidade ao impacto e de dureza indicaram que ocorreu decomposição espinodal da fase a. Medições da diferença da dissolução das fases a e ?, conduzidas no microscópio de força atômica, indicaram que a resistência à dissolução da fase a diminui com o tempo de envelhecimento de forma similar a redução da tenacidade. Os resultados indicam que a microscopia de força atômica é uma ferramenta eficiente para avaliar o grau de evolução da fragilização a 475ºC.

Aug 16, 2017

By Brian Zelenko, William H. Hansmire

"By the time the latest expansion of the Washington Metropolitan Area Transit Authority (WMATA) system, known locally as Metro and which opened in 1976, is completed in 2020, the system will serve 97 stations and operate on 188 km (117 miles) of track on six interconnecting lines. Metro provides a critical transportation link to a population of approximately six million people within a 3,900-km2 (1,500-sq-mile) Washington Metropolitan area and has allowed job growth to expand to all corners of the region. In the 1950s and 1960s, when the system was first conceived and construction began, most jobs were centered in downtown Washington, and most of the workforce commuted by bus or car. Today, transit-oriented development has increased residential, commercial and government facilities near most of the existing 91 stations increasing the importance of the Metro system as a critical transportation link for the region. According to recent American Public Transportation Association (APTA) data, Metro is the second busiest transit system in the United States (after New York City’s transit system).During the nearly 50 years of construction on the Washington Metro system, technology improvements and lessons learned from the global tunneling industry were implemented. Portions of this background and history have been adapted from other work by the authors Roach et al. (2017) and expanded for use herein. For soil tunnels, these improvements included the change from a “two-pass” tunnel lining with a typical initial lining of steel ribs with wood lagging or segmental precast lining erected within the tunnel shield followed by a final lining of cast-in-place concrete to a one-pass lining system of pre-cast concrete gasketed segmental lining. Soil tunnels were originally excavated using open-face tunnel shields, but changed over time. By the late 1980s, tunneling using closed, pressurizedface tunnel boring machines (TBMs) using a one-pass tunnel lining consisting of segmental precast concrete permitted tunneling in a wider range of soil conditions with much less risk of damaging overlying utilities or structures, greater safety for tunnel construction personnel and without the need to dewater the soils. However, due to concerns about conditioning clays with earth pressure balance (EPB) TBMs, open face machines were still favored by contractors for their better advance rates, lower cost and ability to deal with boulders that were occasionally encountered in the Coastal Plain Terrace Deposits."

Jan 6, 2018

By C. S. Gibson

INTRODUCTION I WELCOME the opportunity to speak on Programmes in Safety. The invitation to do so shows that those guiding affairs of the Institute in this District realize the practical importance of this subject. My remarks are intended primarily for mines having 100 to 400 employees, approximately. With minor modifications, however, they apply also to larger or smaller operations. Others, I hope, will derive benefit from this paper, for they, too, have a part to play in accident prevention; for example, contractors such as shaft-sinkers; manufacturers of equipment; and consultants and designers of mining, milling, and metallurgical methods. These troubled times stress, as never before, the importance of efficient operations in mining. The days are gone when neglect can be afforded. Safe working conditions and satisfied employees are essential for efficient production at reasonable cost. The mining industry of Ontario long has been keenly aware of the human aspects of this subject, and as a whole it has done much to decrease the frequency and severity of disabling accidents. The number of fatalities per 1,000 employees has been reduced from a high of 5 some two decades ago to an all-time low of 0.89 in 1948; the incidence was slightly higher in 1949, being 1.17 per 1,000. The reduction in non-fatal compensable accidents also has been outstanding, frequency having ?been reduced from over 200 per 1,000 employees some two decades ago to 54 per 1,000 at the producing mines in 1949. These statistics demonstrate progress. Nevertheless, the general picture still leaves much to be desired when viewed from two other angles.

Jan 1, 1951

By M. Pillay

INTRODUCTION Heat stress continues to be a safety concern in underground mining. This is due to a number of reasons including increasing depths of mining, increased levels of heat generated from machines, ventilation systems being constrained from providing suitable levels of airflow and others. In order to assess if a thermal environment is safe for miners under normal or modified work arrangements, or to specify stop work conditions a heat stress index is used to guide decisions. Historically, a number of heat stress indices have been developed and applied in underground mines. These can be classed under three broad headings; single measurement, empirically based and rational indices. Do any of these indices perform better than the others? Which one allows simple determinations and decisions to be made in the mine? This paper aims to provide answers to these questions by comparing and contrasting three indices; effective temperature (ET), simple air cooling power (ACP) and Thermal work limit (TWL) for a range of typical mining wet and dry bulb combinations? The paper concludes with the identification of areas for future research. BACKGROUND Heat stress causes discomfort, increases physiological strain, decreases productivity and performance, and contributes to increased incidents [1]. Effective management and control of heat stress is particularly important in mining where hot working conditions are very common [2]. Heat stress index is a common indicator that is used by mine safety advisors and managers to guide decisions about safe work practices in mining under normal or modified conditions. According to Howes and Nixon [3] A safe heat stress control strategy for an underground mine has three elements: • Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. • Acceptance of a functional relationship between the environmental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. • A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The link between these elements is an environmental measure that reflects the physiological strain a worker is subjected to. Since the turn of the twentieth century various indices of thermal stress have been developed (McPherson [4], Howes and Nixon [3], Brake [5]). In selecting a suitable environmental measure or index one problem that must be addressed is the ease with which it can be physically obtained relative to it accurately reflecting the physiological strain. No index can be universally applied and there is no single correct measure or index. However if an index has provided adequate control in a particular circumstance, then it can be regarded as correct for that situation.

Jan 1, 2019

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014

By Jerry B. F. Champlin

NIOSHAn accelerated testing procedure developed by the Bureau of Mines for evaluating commercially available corrosion inhibitors is described. Ultra-sonic agitation of the corrodent solutions and the hot-finished mild steel test coupons was used to evaluate the effects of several variables on the effectiveness of two corrosion inhibitors. Small changes in the weight of the test coupons in both controlled and inhibited corrodents, before and after exposure, affected the precision and accuracy of the results. Minute amounts of oxygen in the systems were found to be causing the relatively large deviations in the corrosion developed in the controlled tests. Microscopic examination of the test coupons revealed that both surface preparation and internal strains resulting from fabrication methods materially affect corrosion behavior.

Jan 1, 1965

By Michael J. Klishis

West Virginia University researchers examined risk and exposure in the roof bolter operator's job and developed approaches for preventing accidents and for evaluating system and human performances that may be appropriate as a general application to improve safety and efficiency in the industry. Using a microanalysis of accident data and underground observations, the researchers classified bolting injuries within one of four work routines: 1) drilling bolt holes; 2) bolt installation; 3) machine tramming, (re)positioning and setting the ATRS; and 4) general face preparation. Time and motion studies were then combined with injury data analysis to develop risk and severity indices, as well as a severity-weighted index that served to determine the degree of risk and exposure by work routine. More than two dozen bolting-related problems were identified as potential situations that could lead to injuries or expose workers during their job. Approaches to avoid these situations were suggested and then applied at six mining operations to evaluate specific problems in roof bolting operations. These suggestions encompassed the three E's of Safety (Engineering, Education, and Enforcement) and emphasized the analysis of worker behaviors that lead to human error accidents.

Jan 1, 1993

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By Michael G. Zabetakis

THIS is a summary of the available limit of flammability, autoignition, and burning-rate data for more than 200 combustible gases and vapors in air and other oxidants, as well as of empirical rules and graphs that can be used to predict similar data for thousands of other combustibles under a variety of environmental conditions. Specific data are presented on the paraffinic, unsaturated, aromatic, and alicyclic hydrocarbons, alcohols, ethers, aldehydes, ketones, and sulfur compounds, and an assortment of fuels, fuel blends, hydraulic fluids, engine oils, and miscellaneous combustible gases and vapors.

Jan 1, 1965