Search Documents

By Raymond F. Gray, Victor J. Hoffman, Richard J. Bagan, Harold L. McKinley

The first indication of tungsten in the Bishop area was the discovery of scheelite concentrations in a gold placer operation in the ( since named) Tungsten Hills in 1913. After early intermittent production, the deposits of the district were slowly discovered and developed. The Pine Creek mine, located in 1916 and under the direction of Union Carbide Corporation since 1935, became the principal producer in the district. By the end of 1965, the total production of the district had reached 3,450,932 units of WO3, 17,071,242 pounds of molybdenum, and 19,599,110 pounds of copper. The topography of the district is characterized by its extreme relief, ranging in elevation from 13,986 feet to about 4400 feet in the Mount Tom quadrangle. The present topography is the result of the uplift and erosion of the Sierra Nevada and the great subsidence of the Owens Valley with its related deposition and volcanism. The general structure of the pre-Tertiary rocks consists of a series of tightly-folded metasedimentary and metavolcanic rock remnants surrounded by exposed plutons ranging in composition from hornblende gabbro to alaskite. The metasedimentary rocks consist of low- to intermediate-grade metamorphic equivalents of fine-grained sediments deposited during the Paleozoic era in a miogeosynclinal environment. Later volcanics were deposited in a eugeosyncline. The ore bodies in the Bishop district consist of scheelite-bearing tactite formed by the pyrometasomatic replacement* of calcareous sediments along the contact with an acidic granitic intrusive. A number of the metasedimentary remnants have had tungsten deposited along their edges.

Jan 1, 1968

By Paulo Sérgio Moreira, Geraldo Lúcio de Faria, Rhelman Rossano Urzêdo Queiróz, Amanda Aparecida Fátima Arruda, Ana Cecília de Carvalho

O aço inoxidável ferrítico 410D (UNS S41003) é um aço relativamente novo e ainda em desenvolvimento no mercado Brasileiro. Ele tem sido posicionado como um candidato a substituir aços baixo carbono comuns e aços patináveis em algumas aplicações onde existam exigências no que diz respeito à resistência do material à oxidação e à corrosão. Entretanto, ainda existem algumas lacunas de conhecimento a respeito do seu comportamento mecânico que permitam avaliar a viabilidade de sua aplicação em condições agressivas de trabalho, como por exemplo em temperaturas relativamente elevadas. Partes estruturais de caldeiras, tubulações para condução de vapores e gases quentes, entre outros, são exemplos em potencial para aplicação do aço 410D. Nesse contexto, o presente trabalho avaliou o comportamento do referido aço quando submetido a ensaios de tração a quente nas temperaturas de 300°C e 600°, comparando-se os resultados obtidos com o seu desempenho à temperatura ambiente. Concluiu-se que o aço inoxidável 410D é susceptível ao fenômeno de envelhecimento dinâmico na temperatura de 300°C, tendo sua capacidade de deformação plástica significativamente diminuída. A 600°C observou-se uma diminuição de 45% no seu limite de escoamento e um aumento de 7% no alongamento total em relação à temperatura ambiente.

Oct 8, 2019

By John Ellenberger

The nature of a stone deposit is rarely defined through exploration and engineering design, but more through the actual experience encountered as the mine develops; hence, issues with ground control are often at the forefront for a new mine. Ground control problems account for over 15 percent of lost-time injuries in underground stone mines. The objective of this work is to present actions taken during early development of a stone mine to mitigate the obvious effects of high horizontal stress on ground control. The mine was developed from a box cut with relatively little cover, and high horizontal stresses were not anticipated. Early recognition of possible high horizontal stress resulted in mapping of the mine using the NIOSH-developed Roof Fall Risk Index (RFRI) to provide a baseline to objectively analyze roof conditions. A program of borescoping the mine roof provided valuable roof beam thickness data and found that the roof beam was of minimal thickness, approximately 10 percent of drift width. As the mine developed, it became apparent that ground control problems related to high horizontal stress existed. A concentrated effort was made to improve ground conditions by implemeting a number of mitigation techniques. Actions taken by the mine included systematic roof support, reorientation of mining direction, a lower roof horizon, reduced span widths and reduced mining height in crosscuts to prevent running falls. These strategies resulted in signifcantly improved ground stability.

Jan 1, 2012

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and, education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.1

Jan 1, 1977

By Paul Gilmour

"The principal role of the geologist is to recognize the existence of phenomena before trying to explain them" - B.M. Keilau, 1825; A. Holmes, 1965 Some important groups of mineral deposits in the layered rocks of orogenic belts or greenstone belts occur in horizons characterized by the presence of exceptional amounts of silica, iron and carbon, with more or less significant amounts of manganese. Generally, the rocks involved are well banded. In practice, these five physical features - four compositional and one geometric - are found with many lithological guises. Iron formation, in the full, modern sense of the term (James, 1954), quartzite, ferruginous quartzite, chert, jasper, "tetsusekiei" (Horikoshi, 1969), tuffaceous jasper ("purple porphyry" - Anderson and Creasey, 1958, p. 36), ferruginous or graphitic shale, argillite, slate or schist, and hematitic tuff are but a few of the more familiar of the names that have been assigned to these rocks. Widely acknowledged and well-documented examples of metallic deposits found in such sediments include concentrations of iron and manganese and stratabound, polymetallic, massive pyritic sulfides. Less familiar examples include occurrences of asbestos (Miles, 1953; and Coetzee, et al., 1976), antimony (Coetzee, 1976), and perhaps stratabound deposits of Au-Cu-U-W-etc., such as Aitik in Sweden (Mining Magazine, 1975; and Nilsson, 1979) and Olympic Dam in South Australia (Roberts and Hudson, 1983). The case of gold is intriguing. An association between gold and iron formation has been identified at several famous deposits and districts, such as Yellowknife, N.W.T. (Morton, 1979), Homestake, S. Dak. (Sawkins and Rye, 1974), Vubachikwe, Zimbabwe (Fripp, 1976) and the Barberton district, R.S.A. (Hammerbeck, 1976). Yet a critical reading reveals the existence of many other hitherto unsuspected examples. The purpose of this note is to draw attention to that omission and the apparent explanation for it. It is not hard to detect the two most probable reasons for the discrepancy between reality and the record.Most occurrences of gold are associated, not with the familiar banded iron formation or interbedded magnetite and chert (technically, the magnetite-banded variety of the oxide facies), but with the enigmatic carbonate, sulfide and silicate facies of iron formation and/or with rocks evidently related to iron formation. All too commonly, the unfamiliar facies of iron formation have been identified by field and mine geologists and not a few researchers as products of regional metamorphism and hydrothermal alteration, as mafic igneous rocks, or as conventional sediments, ie., without regard to their intrinsically ferruginous nature. The justification for these two complementary assertions is largely to be found in the recognition of a characteristic suite of metals and minerals in gold deposits known to be associated with iron formations. Although, from a geological standpoint, a lithological association is more important than a mineralogical assemblage, the latter is the more likely of the two to be diagnostic. This arises from the different natures of mineral and rock classifications, The identification of a mineral or an element is a matter of fact. Owing to the genetic component inseparable from petrographic nomenclature, viz., "igneous": a rock (believed to have been) derived from a melt, the identification of rocks depends on inferences or conclusions about their mode of formation - conclusions that are commonly debatable and, all too often, involve subjective judgements. This is especially prone to be true, if - as at many of the gold occurrences in question - the host rocks have been metamorphosed and/or "altered". In the notes that follow greater weight has accordingly been assigned to elemental and mineralogical than to host rock composition. In other words, if, in a given gold occurrence, the suite of metals and minerals present conforms to the standards of the subject class, whereas the names assigned to host rocks do not, the latter will be viewed as suspect.

Jan 1, 1985

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017

By A. Flora, E. Bilotta, F. Foria, V. Nappa

"All the typical applications of deep mixing rely on the good mechanical properties of the improved columns to strengthen or stiffen the ground for a number of geotechnical applications.This paper focuses on a completely different kind of deep mixing, carried out in order to obtain columns much softer than the surrounding soil. This kind of deep mixing, named Soft Deep Mixing (SDM), is introduced as an original means to tackle seismic risk, and can be convenient when the existing structure to be protected has a historic relevance that cannot be altered with structural modifications. The idea is that properly assembled layers made of partially overlapped SDM columns, with dynamic impedance much smaller than that of the surrounding soil, will filter and reflect most of the seismic energy.The paper presents the results of some 2D parametric numerical analyses aimed to investigate the seismic performance of this innovative approach. Simplified dynamic inputs (Ricker wavelets, having only one largely predominant frequency) were adopted to better understand the effect of signal frequency. The analyses show that the effectiveness of the soft grouted isolating barrier depends on soil and SDM geometrical, physical and mechanical properties, as well as on the frequency content of the seismic input.INTRODUCTIONPassive structural systems installed at the foundation level of existing buildings are a common solution to protect them against earthquakes. However, installation procedures are expensive and not always feasible, as for instance in the case of valuable buildings. As an alternative, ground improvement techniques can be used to modify ground properties, in order to mitigate the intensity of shaking at ground level. The propagation of shear waves in the ground can be modified by introducing a layer of artificially modified material, having a dynamic impedance (defined as n =p VS, where p is the material density and VS the velocity of shear waves) very different from that of the natural soil. Both very high or very low values of the dynamic impedance of the grouted soil (nt) can be effective in reducing the overall transmitted energy, with the difference that – for a given reduction of the transmitted energy - stiff grouted layers tend to filter the low frequency components of the amplitude spectrum without modifying in a significant way the high frequency components, while soft grouted layers have the opposite effect. Then, ideally the choice of the best grouting technique should be made considering the effects of the different frequency components on the building to be protected. These effects are detrimental for the structure when they are close to its natural frequency: high frequency components result into large structural loads on massive squat structures (high natural frequency), and low frequency components may be critical for tall and flexible structures (low natural frequency). Therefore, the typical procedure of stiffening the uppermost soil layers regardless of the kind of building to be protected is not necessarily beneficial, and for the case of squat structures soft grouting should be preferred. However, this procedure has not been taken into account yet in the engineering practice, and may pose static problems at ground level (i.e. excessive static settlements)."

Jan 1, 2015

By A. R. Khodabandeh, T. Nematkhah

Correct selection of forging parameters is very important to produce sound superalloy parts. In this investigation nickel-iron base superalloy IN901 successfully forged and seal spacer, which is a part of airplane with about 11 kg weight has been produced. Forging has been performed on the basis of hot compression results, which show deformation above 1100°C associated with dynamic recrystallization (DRX) which can increase the workability of material. On the other hand annealing at 1100°C decreases the flow stress during hot compression, and then increases the material formability. Then billets annealed at 1100°C in electrical furnace for 24 hours and reheated again to 1100°C before forging. Initial square cross section billet with 128mm side and 202mm length forged immediately after reheating by 80MN mechanical press. Specimens forged in five steps: upsetting, three steps molding and finishing. Preformed and molded specimens reheated in electrical furnace before later step of forming. Finally specimens trimmed by 1 OMn mechanical press and hot set by hydraulic press and then cooled in air to room temperature. Results show that reheating temperatures has been selected correctly because there isn't any surface crack and die cavities filled completely by forging material. Material flow has been carried out properly and there isn't any defect in critical points especially in extradoses and intradoses. Microstructural examinations show that grain boundaries contain Ti-rich globular particles that formed during cooling.

Jan 1, 2006

By William K. Cunningham

The investigation described in this report was begun as part of the Bureau of Mines progress to develop acid processes for the extraction of alumina from low-grade bauxite and. clays. A domestic shortage of high-grade bauxite sui table for treatment by the Bayer process became acute as a result of' World War II; an intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted. The laboratory development was described in a preceding Bureau of Mines publication wherein the basic theory for the design and erection of a pilot plant maybe found. A 2-ton-per-day continuous pilot plant was constructed and successfully operated at College Park, Md., which demonstrated conclusively the chemical and mechanical feasibility of a solvent purification process for aluminum sulfate. The estimated production cost of $38.64 indicates that under present market conditions the process would not be economically feasible.

Jan 1, 1948

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

By D. H. NETLAND

DURING the year 1907 an investigation of the Clinton formation in New York has been carried out under the direction of the State Geologist, and a full account of the results has been prepared for publication.1 The more important economic features of the report are summarized in the present paper. Previous knowledge of this, the type, section of the Clinton has been contributed mostly by Hall and Vanuxem in their reports for the Natural History Survey of New York, which were issued in their final form in 1842-43. Brief accounts of the ore-occurrences have been given by B. T. Putnam,2 J. C. Smock,3 A. H. Chester,4 and E. C. Eckel.5 Prof. C. H. Smyth, Jr.,6has discussed the origin of the Clinton ores in two papers, which, so far as the local occurrences are concerned, have removed all doubt that may have existed on that subject. Distribution of the Clinton Formation. The Clinton strata in New York State are restricted to a single belt, Which extends from the eastern central part to the Niagara river, which it crosses, and thence continues for some distance into the province of Ontario. The New York

Mar 1, 1909

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By J. R. Heberger, B. H. Ngo

The Safety Pays in Mining v2.0 web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app categorizes injury cost by part of body injured, by the cause of the injury, or by the nature of the injury. When the user selects one of over 150 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining v2.0 will estimate the total costs of the selected injuries and the estimated impact of total injury costs on mining company profits and will provide some examples of services and personal protective equipment on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining version 2.0 web application by discussing the development and updates to the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app.

Feb 1, 2024

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By J. M. Benson

Metal powder compaction offers unique advantages in the manufacture of net-shape components using techniques such as laser sintering, conventional press and sintering, metal injection moulding, direct rolling, direct forging, and hot isostatic pressing. If the output from the primary metal production process is in powder form, then considerable cost and energy savings can be realized by direct conversion to semi-finished or final shapes. This possibility exists for titanium and possibly also for Ta, Zr, Hf, and Nb metals. However, these attractive benefits are associated with some significant risks. The high surface-to-volume ratio of powder particles coupled with the reactive nature of these metals means that special care must be taken when handling them. Powder explosions are unfortunately still a regular occurrence internationally and these often result in serious injury and loss of life. Even seemingly 'safe' compounds such as sugar, flour, and grain can be extremely hazardous when handled or milled and dust clouds are produced. In addition, exposure to airborne particles can have adverse effects on the human body, especially when particles are inhaled on a regular basis. Furthermore, the medical consequences of these are not fully understood, especially in the case of nanoparticles. The impact is often not observed immediately and debilitating illnesses may emerge only years or decades later. As far as is known, there are no South African guidelines for handling of metal powders. This paper attempts to provide an awareness of the risks associated with metal powders (including those produced indirectly by other metalworking/finishing operations) as well as some guidelines for their safe handling, based on international best practices.

Jan 1, 2012

By John C. Machisak

INJURY data and experience, with related employment statistics, at coal mines in the United States for 1958 are presented in this publication under the following general sections: (A) General injury experience: Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location. (B) Selected injury experience: Tables 7 to 38: Current data on principal agencies of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience by States: Tables 39 to 43: Current data on injuries, their causes, rates of occurrence and severity; employment and production data by work location, by States. (D) Major disasters: Table 44: Data on major disasters from 1949 to 1958. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 45 to 49: Data on fatalities and their causes at bituminous coal, lignite, and anthracite mines from the earliest records through 1958.

Jan 1, 1961

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core.

Jan 7, 1951

By V. H. Gottschalk

Among the procedures developed by the Germans for providing the tonnage of iron powder needed to make rotating bands for artillery shells is the use of a ceramic tunnel kiln, not only for finishing the reduction of centrifugal powders but also for making so-called "brickyard sponge iron," which, after crushing and grinding, seems to yield a product suitable for powder-metallur- gical purposes. The final report issued jointly by the German Powder-Metallurgical Society (DPG) and the Chemical-Metallurgical Branch of the Research Depart- ment of the Metallgesellschaft, Inc. (ZFC of MG) gives the available details of this procedure, which may be regarded as a further development of the process in commercial use since 1911 at a ceramic plant in Hoeganaes, Sweden. The Bureau of Mines' wartime development of the Hoeganaes process also cul- minated in the adaptation of ceramic tunnel kilns for carrying out the solid- carbon reduction of iron ores, and comparison with the German technique should further advance the art. This information circular is issued as a supplement to Bureau of Mines reports of investigations Nos. 3819,2 3822, 3841,2 and 4271, on brick- yard sponge iron and is based on four German reports entitled "Making Iron. Powder in the Tunnel Kiln," translated from FIAT microfilm reel H-46, frames 9190-9209, 9280-9299, 9339-9357, and 9377-9384 (PB L 70042), which represent the four original research reports, Nos. 2005, 2008, 2010, and 2012, respec- tively, of the Metallgesellschaft, Inc.

Aug 1, 1948