Search Documents

By Boyd Guthrie

As the American petroleum industry surveyed its position in early 1937, it had many reasons to be optimistic concerning its future. The industry had emerged successfully from the depression, and for the first time since 1929 it had produced over one billion barrels of crude oil in a single year. The demand for gasoline and fuel oils was up, and reserves of crude petroleum and production capacity seemed adequate for the future. Although production of crude oil dropped slightly in 1938, the oil industry was still in a good position with respect to its supply of raw material, which improved economically in 1939 with the decrease of crude-oil stocks in storage above ground. However, by 1940 a threatening cloud (the invasion of France and its rapid surrender) had appeared on the horizon. This aroused Somme fears as to the industry's immediate future, and these fears were intensified the following year when the United States entered World War II. As the war progressed, more and more ships, planes, and vehicles were produced, and the problem of obtaining enough liquid fuels to supply them intensified. Hearings were held in August 1943 before a subcommittee of the Committee on Public Lands and Surveys of the 78th Congress to determine the advisability of passing legislation to promote the development of synthetic liquid fuels.

Jan 1, 1951

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By F. Mielli

Camera systems and video surveillance are usually associated with people and asset protection. However, they can be applied in a mine environment beyond conventional surveillance: For process monitoring, collision avoidance, sizing, flotation cells, conveying systems, blasting, objects and people tracking, thermal profile, and to automatically identify equipment that is missing parts,. Image and video solutions can be driven by better integration of powerful video analytics and cameras systems in automation tools such as process controllers and supervision systems.

Feb 27, 2013

By Paul M. Hall

In the last several years, the coal mining industry has made significant changes in the design of longwall mining systems to make them more productive. Some changes, such as increasing the length of the coal faces and increasing the capacity of the face conveyors, have resulted in problems with achieving sufficient motor torque to start and operate the longwall face conveyors. Other changes, such as increasing the size and/or decreasing the percent impedance of longwall power center transformers, have resulted in problems with the short-circuit currents on the transformer secondaries exceeding the interrupting ratings of the molded case circuit breakers used to protect the secondary circuits. A survey of 24 longwall mining systems in northern West Virginia was conducted to investigate both problems. The results of the survey are presented and analyzed. Several recommended solutions to the problems are presented to enable the coal mining industry to design safe and productive longwall mining systems.

Jan 1, 1982

By Donald L. Siebert

This profile study of the commercial secondary aluminum industry examines not only the elements that form the industry but also the technological contributions of each toward industrial growth. Concise descriptions of processing methods trace aluminum scrap from generating sources to marketable industrial and consumer goods. Economic and marketing appraisals are used to illustrate the impact that recent technology has had upon the secondary aluminum industry. Price, supply, demand, competition, and substitutes are selected as components of an economic model of the secondary industry and are used to illustrate the aggregate effects of technological changes. The final section is a conceptual look at the future in which sensitive economic indicators (such as die casting in the automotive and appliance industries) are examined as well as the problems of conserving mineral resources by retrieving secondary aluminum from solid waste.

Jan 1, 1970

By Sylvia S. Eskander, Sherif S. AbdelSalam, Mona B. Anwar

Expanded Polystyrene (EPS) geofoam has long been used in numerous geotechnical applications due to its lightweight and durability. Among these applications is the use of EPS as an alternative fill material to conventional roadway soil embankments. This study investigates the benefits of using EPS roadway embankments to reduce the induced stresses and strains on the underlying peat and soft clay. Firstly, mechanical and interface properties of the EPS were acquired from a companion study that also considered the cyclic loading and creep effects. In order to determine the actual stress-strain distribution within the EPS blocks, a physical prototype was developed in this study with overall dimensions of 1.2 x 1.0 x 0.5 m, with a density of 35 kg/m3. The prototype EPS blocks were subjected to cyclic loading with intensities ranging from 10 to 50 kN. Then, a numerical model was developed to simulate the behavior of EPS roadway embankments. The numerical model outcomes were verified against the prototype measurements. A parametric design study was also conducted to develop a correlation between EPS embankment height and the stress-strain that occur in the underlying strata. Results showed that EPS embankments could reduce stress and settlement in the underlying soil by about 40% and 54%, respectively. EPS APPLICATIONS AND BACKGROUND Expanded Polystyrene (EPS) geofoam blocks have been effectively used during the past several decades in numerous geotechnical applications. EPS static and dynamic properties as well as interface behavior were extensively characterized in various published studies such as that conducted by Horvath, 1994; Stark et al., 2004; Zarnani and Bathurst, 2008; Trandafir et al., 2010; Athanasopoulos et al., 2012; AbdelSalam and Azzam, 2016; and others. However, to be able to use locally produced EPS blocks, its physical and mechanical properties must be thoroughly determined. The lightweight and compressible material of EPS geofoam makes it suitable both as a backfill and for absorbing pressure in both the vertical and horizontal directions. Kim et al. (2010) adopted EPS as an alternative for soil backfill around buried pipes; their model showed a reduction in the vertical stress acting on the pipes by up to 36%. Oshati et al. (2012) presented a case study of a field-instrumented box culvert with EPS blocks on top, which reduced vertical stress by 58%. Meguid et al. (2017) used an EPS inclusion to surround culverts and achieved up to 72% stress reduction, depending on the EPS density and the culvert depth to width ratio. AbdelSalam et al. (2017) used a relatively thin EPS inclusion behind flexible cantilever retaining walls, verifying that the lateral pressure can be significantly reduced by 25%; they also developed a design chart for this application. Moreover, AbdelSalam et al. (2019) investigated the use of EPS as a lightweight alternative for soil backfill above shallow tunnels. It was found that EPS had created a differential movement between the wedge located above the tunnel and the neighboring soils, which accordingly reduced the vertical stress acting on the tunnel by 85%, due to the use of lightweight EPS material and positive soil arching.

Jan 1, 2019

By Lourens Scheepers

Mining induced seismicity and rockbursts have been part of the deep level gold mining industry in South Africa for many years. One could be forgiven for thinking that we should know everything there is to know by now to have rockbursting under control to a level that it has minimal impact on safety and production. Well, we don’t… There are things we know that we know, and they are implemented, or should be. There are thigs we know that we don’t know, and they are researched, or should be. There are things we don’t know that we don’t know, and, well, we don’t know… We know that seismicity and the associated potential for rockbursts generally increase with an increase in stress (increase in mining depth and/or mining span and creation of remnants) and proximity to faults and dykes. We know there are a number of potential sources of events in a mine; that is: mining abutments, pillar abutments, mining faces and geological structures (faults and dykes). We know there are a number of event mechanisms associated with these sources; that is: slip on a geological structure, shear through intact rock and bursting of the rock near the edge of a mining excavation. One of the tools used more and more and with increased success to identify event source mechanisms is Moment-Tensor analysis (MT). This typically assist in differentiating between three event mechanism components: volumetric deformation component, axial deformation component and slip / shear component. The insight gained from MT assist greatly in identifying the most likely event source to assist in understanding the rockmass response to mining. We know that the seismic response in our mines are mining induced (not natural). This may seem trivial, but it is important to realise that we influence the seismic response with the way we mine, and by how much we mine (extraction ratio). Therefore we put design rules and strategies in place to reduce the seismic hazard and we install rockburst support in our mining excavations. We know the seismic response to mining is influenced by the properties of the rockmass, including strength, stiffness and brittleness, but quantifying its influence is typically more difficult than expected. We know numerical modelling can improve the engineer’s understanding of the potential rockmass response associated with designed mining layouts and strategies. For our environment (narrow, tabular large area) elastic boundary element modelling remains the most convenient and practical approach, but it overestimates the stress at mining abutments and underestimates the stress further away from these abutments. Adding a crushing (based in limit equilibrium) modelling approach vastly improves the boundary element modelling ability to simulate the deformed (interpret fractured) zones and associated redistribution of stress. We don’t know how to quantify what an acceptable seismic risk is. We don’t know if we can mine remnants at an acceptable seismic risk. Some remnants are extracted surprisingly easy, others serve us with devastating rockbursts. The limit equilibrium modelling shows potential to significantly improve our ability to quantify the rockburst risk. We don’t know if large-scale preconditioning is possible and will be effective to significantly reduce the seismic risk associated with remnant and pillar mining. Research is required (and has been initiated). Vast areas of ground have been extracted historically in the South African gold fields. Most gold reserves are now in deeper ground (4000 m) and historic remnants (areas left before due to mining difficulties) as well as pillars (regional stability pillars). If we cannot find ways to extract these reserves at acceptable risk levels, the future of the South African gold mining industry is very short.

Apr 26, 2022

By Robert M. Busche

[Recent developments in the gasification of coal, both by the Bureau of Mines and American industry, have intensified interest in the thermodynamic and kinetic principles necessary for understanding the reaction mechanism and rates and the physical changes that take place. In the course of a Bureau of Mines study of the kinetics of coal gasification at the Synthetic Liquid Fuels Demonstration Plant, Louisiana, Mo., a bibliography of approximately two references was compiled. They are listed n this publication and refer both to American and foreign sources.]

Jan 1, 1952

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 established the Office of Mine Safety and Health (OMSH) within NIOSH and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. Subsequently, Congress provided additional funding to NIOSH to initiate and continue the program. OMSHR has fulfilled this Congressional mandate through annual Broad Agency Announcement (BAA) solicitations, directed Requests for Proposals (RFP) and Inter-Agency Agreements (IAA), and has further expanded the program through capacity building BAA contracts with U.S. university mining departments in the areas of mine ventilation and ground control. This paper describes the extramural funding program and broadly examines the results of the 150+ contracts issued to date, grouped into key focus areas. INTRODUCTION The Mine Improvement and New Emergency Response Act (MINER Act) of 20061 established the Office of Mine Safety and Health Research (functioning as the Office of Mine Safety and Health Research or OMSHR) within the National Institute for Occupational Safety and Health (NIOSH), and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued over 150 contracts focused on worker health and safety. Initial funding for this program was provided by Congress through two Emergency Supplemental Appropriations (ESA) and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation; ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website2 and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously.3"

Jan 1, 2018

By William D. Macdonald

The Upper Devonian Kettle Point black shale of southern Ontario is poorly exposed. Structural maps pre-pared from the data of numerous wells show that the upper surface of the formation has low regular relief, and that the lower surface reflects domes in the Middle Devonian and also local subsidence of the Devonian rocks due to solution of salt in the Silurian Salina Formation. The appearance of minor amounts. of marcasite, pyrite, and calcite, m that order, as interpreted from the evidence of concretions from the type locality at Kettle Point is thought to have been influenced by a rise m the pH within anaerobic sediments preceding compaction.

Jan 1, 1960

By Robson Luís da Silva Nascimento

O mercado do aço no mundo está muito competitivo, e as indústrias siderúrgicas têm desenvolvidos projetos com foco na melhoria da qualidade dos aços e na redução dos custos dos processos de fabricação. Este trabalho descreve os avanços nos processos de lingotamento contínuo, com foco na redução do sucatamento de placas por “bolsa”. Esta melhoria consistiu na modificação na taxa de refrigeração aplicada na placa de cauda durante o processo de descarga da máquina (final de lingotamento). A implementação dessa ação propiciou uma homogeneidade na solidificação das placas de cauda aumentando assim sua temperatura de extração reduzindo significativamente o sucatamento das mesmas. Outras melhorias obtidas com o trabalho foram a redução das ocorrências de placa parada no interior da máquina, redução das ocorrências de restrição de velocidade por Baumann, redução das ocorrências de intervenção para regularização de GAP e melhoria na qualidade superficial. O trabalho foi realizado sem investimento contribuindo na redução do custo de transformação do aço em placa.

Jul 30, 2018

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By Oluwafemi Salami

Conducting full-scale fire experiments in underground mines is difficult and expensive. Sometimes, it is impossible to carry out fire tests in mines due to the danger they pose to mine workers and the underground facilities. However, understanding the potential occurrence of fires in a mine and their dynamics is critical to developing an appropriate emergency evacuation plan, fire suppression, and firefighting techniques. In this study, a numerical fire model using computational fluid dynamics (CFD) with fire dynamics simulator (FDS) 6.7.6 was developed to examine the influence of tunnel bifurcation on maximum temperature beneath a tunnel ceiling. The model was validated using full-scale experimental data. The maximum ceiling gas temperature predicted using FDS and measured maximum smoke temperature during the experiment shows good agreement. The study shows that bifurcation could lower the maximum ceiling temperature of fire-induced smoke in a subsurface environment. The findings from this study apply to the broader field of ventilation and fire life safety in tunnels and other underground environments.

Jun 23, 2024

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By W. J. Fene, G. W. Grove

An important activity of the Safety Division of the Bureau of Mines , in its efforts to reduce accidents , is the safety inspection of mines . Inspections are made at the request of the operators and are not connected with the inspections by the various State departments of mines . The operating management is furnished with a confidential report of the results of the Bureau's inspections , with recommendations for elimination of the hazards found . These mine - safety inspections include a study of mining practices , conditions , and equipment and in some cases the sampling and analysis of mine air and coal dust . The Bureau of Mines has no regulatory powers , therefore the recommendations made in these reports are merely suggestions , and operators are not required to adopt them . Mine inspections are a check on safety standards , methods , and practices and are essential to any accident -prevention program . A foreman or superintendent may be sincere in his efforts to operate a mine safely and believe that he has done everything possible to attain this end . However , experience has shown that because of his familiarity with the mine and the consequent " nearness " of its various features many unsafe conditions may be , and in most cases are , overlooked ; an inspector , particularly an outsider who is trained to look for hazards , can point out the unsafe conditions overlooked by the foreman or superintendent . Some companies employ safety engineers who make regular inspections of their mines , report substandard conditions and hazards found , and make recommendations for correcting them . Unless these recommendations are carried out the inspections have little value . In making recommendations , due consideration should be given to the feasibility of carrying them out ; the management may and very often does consider a recommendation impracticable because of the

Mar 1, 1935

By A. Takala, H. Cline, D. Girard

"This article describes the project development and successful implementation of a particle sorter at the Kensington mine. The Kensington underground gold mine and associated milling facilities are located within the Berners Bay Mining District on the east side of Lynn Canal about 45 miles north-northwest of Juneau, Alaska. The paper describes the project from concept, through the development phase, including test work confirming feasibility, to a discussion of operational data and includes shared experiences from operation and maintenance. The project has proven successful in recovering gold that was previously lost to the waste dump and has already resulted in a positive return on investment. The payback was achieved in less than one year.INTRODUCTION The first paragraphs of this paper describe Coeur Mining and the Kensington Mine, its history, geology, mining operation and mill. The second part of this paper gives a quick introduction to sensor-based sorting in general and X-ray transmission sorting (XRT) in particular. This article does not cover costs or economic impacts apart from the pay-back period for the investment at Kensington. Interested readers find more in information on this in the literature (Kleine & Wotruba, 2010; Robben, 2013). Since the publication about XRT sorting at TGME in Pilgrim’s Rest (Kleine, Riedel, Ketelhodt, & Murray, 2010), this is the first time that a comprehensive data set on gold ore sorting using XRT is published. Following chapters highlight the aim of the project for Coeur Kensington, project development through testing and operation before concluding. ABOUT COEUR MINING’S KENSINGTON OPERATION Coeur Mining is the largest U.S.-based silver producer and a significant gold producer with five precious metals mines in the Americas employing approximately 2,100 people. Coeur produces from its wholly owned operations: the Palmarejo silver-gold mine in Mexico, the San Bartolomé silver mine in Bolivia, the Rochester silver-gold mine in Nevada, the Kensington gold mine in Alaska, and the Wharf gold mine in South Dakota. The Company also has a non-operating interest in the Endeavor mine in Australia in addition to royalties on the Cerro Bayo mine in Chile, the El Gallo complex in Mexico, the Zaruma mine in Ecuador, and the Correnso mine in New Zealand. In addition, the Company has two silver-gold feasibility stage projects—the La Preciosa project in Mexico and the Joaquin project in Argentina. The Company also conducts ongoing exploration activities in Alaska, Argentina, Bolivia, Mexico, and Nevada. The Company owns strategic investment positions in several silver and gold development companies with projects in North and South America."

Jan 1, 2017