Search Documents

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By C. Flores

A novel process using solid metals for the direct reduction of more noble metal ions from solvent extraction organics has been developed. Base metals recovery has been the principal focus of investigations to date but feasibility tests have now also been made on galvanically stripping selected precious metals. In this study gold (III) was loaded from an aqueous HAuCI4 .3H20 solution into a mixed organic 40 vol.% TBP, 10 vol. % D2EHPA in kerosene. The direct precipitation of metallic gold from the loaded organic phase using zinc powder and iron, aluminum and copper slabs at 70 °C was successfully demonstrated. The gold reduction rates were relatively fast even though the conductivity of the organic solutions is very low. The reaction rates were studied as a function of the variables zinc particulate size, oxygen and nitrogen atmosphere, water content in the organic phase, organic ratios and temperature. The gold morphology was usually powdery or dendritic in nature but continuous films were obtained in some instances. Activation energies were calculated and possible reaction mechanisms are discussed. In general, the results obtained were very promising and showed that gold can be successfully cemented from selected organic solvents by galvanic stripping using less noble solid metal reductants.

Jan 1, 1995

By M. J. Collins

A hydrometallurgical process has been tested at the Sherritt Research Centre for separation of zinc, lead, copper and precious metal values from the zinc oxide fume leach residue stockpiled at the HBM&S operations in Flin Flon, Manitoba. Zinc is found primarily as zinc femte and sphalerite in the residue, lead as lead sulphate and jarosite, and copper as sulphide and jarositic compounds. Gypsum and siliceous gangue are significant diluents. The separation process includes hot acid, atmospheric and reducing (sulphur dioxide) leaching; zinc, copper and lead flotation; and atmospheric iron removal steps. Zinc is recovered to a high strength zinc sulphate solution and to a zinc sulphide concentrate suitable for feed to a roaster or to a zinc pressure leach plant; lead to a high grade lead sulphate concentrate suitable for feed to a lead smelter, and copper to a high grade copper sulphide concentrate suitable for feed to a copper smelter. Precious metals are divided between the zinc, lead and copper concentrates.

Jan 1, 1993

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By Geoffrey Brooks, Ben M. Ekman, M. Akbar Rhamdhani

"Concentrated solar collectors including solar simulators have been studied to concentrate solar radiation to flux levels capable of reaching temperatures of 3000K. Currently, there are no industrial scale solar reactors used for material processing and only small research units have been tried. Various laboratory scale solar reactor designs are reviewed including their operating temperature and heat transfer efficiency. Solar reactor designs can be classed into directly or indirectly irradiated and single or double cavity construction. Thermal efficiencies of up to 40% have been achieved in experimental units while operating at 1500K. Problems are encountered that relate to the transfer of high heat flux. Hybrid reactor system should be considered in the future to overcome some of the practical issues associated with solar thermal reactors.I. INTRODUCTIONIn the high temperature processing of materials, such as the production of metals, cement, refractory or glass, the reactions are typically performed in the range of 500° to 2000°C. Metals are produced from minerals, which maybe oxides, sulphides, chlorides or silicates, and to recover the metals, these compounds have to undergo chemical reaction to liberate the metal. The thermodynamic stability of these compounds found in minerals necessitates the use of high temperatures to break down the bonds between the metals and other elements. Normally, the raw metals produced from smelting require refining, which is often carried out in the molten state. As new energy sources have been established, new furnace designs have evolved to incorporate the latest technology. Although solar energy has existed longer than all the current energy sources, it has not yet been incorporated into any industrial smelting; refining or melting processes. The solar radiation reaching the earth’s atmosphere, called the “Solar Constant” (SC), is defined as the rate at which solar energy is incident on a surface normal to the sun’s rays at the outer edge of the atmosphere when the earth is at its mean distance from the sun. The currently accepted value is 1367 W/m2 [1]. The earth intercepts only a small amount of this and 30% is reflected back into space, 47% is converted to low-temperature heat and reradiated into space and 23% powers the evaporative and precipitation cycle of the biosphere [2]. As a result, the solar energy reaching the earth’s surface is weakened considerably to about 1000 W/m2 or one sun, on a clear day and much lower on cloudy or smoggy days [3]. The thermodynamic limit for solar concentration is determined from the inverse square law [4] by the factor sin2? = 46,764 sun’s [5] where ? is the angular size of the sun and equals 0.0093 radians [7]. This would produce a steady state temperature equal to that of the sun’s surface of approximately 5800oC. In practice however much lower concentrations are achieved due to geometrical and optical imperfections, shading effects and tracking inaccuracies. Optical configurations based on parabolic-shaped mirrors are commercially available for large-scale collection and concentration of solar energy for the generation of electrical power. The most common configurations used for concentration of the sun’s energy in solar thermal applications are parabolic troughs, solar towers and parabolic dishes [8,9]."

Jan 1, 2014

By Markus A. Reuter, Jacob Wood, Robert Matusewicz

Over the last 20 years, significant improvements in copper smelter productivity have been realized through the advent of continuous smelting processes. This progress has until recently however, not been carried through to copper converting. Peirce-Smith converting has been widely used by the copper industry for 100 years but is limited by its batch nature in achieving large scale of production. A logical next step is therefore copper converting on a continuous basis with its inherent environmental benefits. A number of continuous converting technologies are currently in use or being developed within the copper industry, the majority of these operating with calcium-ferrite slags. A notable exception however is the Ausmelt Continuous Copper Converting (C3) technology which has focused on operation with ferrous-calciumsilicate or loosely called olivine type slags. This paper discusses the merits of the Ausmelt C3 process and the advantages offered in terms of operational flexibility and process control arising from the use of lime modified iron silicate slags. It also examines the effects of key process variables pertinent to continuous copper converting from both a theoretical and experimental/operational perspective.

Jan 1, 2009

By Zhigan Deng

Ni–Mo ore is a black shale containing amorphous colloidal sulfides which have highly active. The oxygen pressure leaching behavior of nickel from black shale in aqueous media is presented. The effects of agitation speed, temperature, oxygen partial pressure and particle size on the rate of nickel leaching were determined. The results indicate that at low temperature hydrothermal and excess oxygen presence, the amorphous sulfides are easily oxidized to sulfuric acid and sulfate, and leaching nickel. The mathematical analyses of the experimental data for various experimental conditions indicated that the dissolution process was controlled by the chemical reaction during the early stage of dissolution, and was then controlled by liquid-film diffusion. In the initial stage of leaching, the reaction depends on oxygen partial pressure.

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By T. M. Dreher

The difficulties associated with the operation of a classical rhodium refining process have prompted many attempts to develop a viable solvent extraction flowsheet for rhodium. Recent investigations at McGill University have involved the activation of rhodium prior to its solvent extraction. The role of activation is to convert the aquochloro complexes of rhodium to a form extractable by conventional solvent extraction reagents. In the novel separation scheme identified, chloro complexes of rhodium are converted to bromo complexes, which undergo aquation to a lesser extent, making them more easily extracted. Rhodium is then extracted using Kelex 100, and stripping is achieved by use of a concentrated chloride based solution. Separation of rhodium from iridium is achieved by either prior reduction of Ir(IV) to Ir(III), as the latter is not extracted, or via co-extraction and differential stripping. A conceptual flowsheet for the refining of rhodium using this method is proposed.

Jan 1, 1998

By A. Block-Bolten

Copper concentrates from northern Peru contain large amounts of arsenic and antimony in the form of sulfosalts like enargite, tennantite and tetrahedrite. These impurities affect up to 30% of Peruvian copper production. Under the sponsorship of the Instituto Geologico Minero y Metalurgico in Lima a project to separate copper from arsenic without pollution of the environment is being carried out at the National University of Trujillo in Peru. The U.N.T. process is unique in the respect of using .low melting salts as solvents, and sulfides of metals with high cation potential as destructors of the complex sulfosalt molecules. Laboratory scale experiments have given encouraging results but interesting and difficult problems developed on scale-up. The process is pyro-hydrometal-lurgical and under certain circumstances its economics are promising.

Jan 1, 1981

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Seyed Mahdi Abbasi, Adel Sheikhhosseini

"This research was conducted to study the changes of microstructure, chemical composition and mechanical properties ofIN718 superalloy after adding aluminum to the ESR process slag. The experiments were performed in VIM and ESR furnaces. The results showed adding 1.5 percent aluminum to the slag increase lave phase in the IN718 samples from 0.34 percent in the base sample to 3.0 percent. It also indicated that the more increase of aluminum in slag cause decrease in the aluminum absorb yield in the superalloy.it is observed that increasing aluminum from 0.7 to 1.1 and then to 1.5 percent caused a decrease of absorb from 91.4 to 76.3 and 74.6 percent respectively due to increasing of aluminum oxidation. According to the results, tensile strength increased and ductility declined in the IN718 samples mainly because of rising the amount of y' volume fraction.IntroductionIN718 superalloy is an iron-nickel base superalloy with constant mechanical properties at medium at high temperatures. For the past seven years a considerable amount of time and effort has been expended by both suppliers and users in the study of Alloy 718 [ 1]. The interest in this material stems not only from the interesting metallurgy associated with the alloy, but with the large usage of the material in numerous applications In fact many people believe that the projected use of this alloy increase significantly over the next several years, The large use of Alloy 718 is the result of its performance in respect to high strength, good ductility, good repair weld ability and from its versatility of being supplied in various product forms. This superalloy is used in wide ranges of industries such as aerospace and gas turbines [2]. In the past more than 20 years many researchers did a lot of work to improve the structure stability of IN718 at high temperatures and intended to develop a new 718 type alloy to be used beyond 650 °C. One of the methods is to control and phase precipitation behavior by means of adjustment of Al, Ti and Nb contents. The other idea is to strengthen the matrix by altering the content of solid solution elements such as W and Co. The adjustment of these alloying elements can change phase precipitation behavior [3]. If detailed information dealing with phase precipitation behavior can be obtained before experimental work for alloy development, a lot of time can be saved and the development cost can also be reduced. In recent years, computer modeling based on experimental data plays an increasing role in alloy design and development. Adding Al to the Iron and Nickel increas the strength of superalloy by formation of y phase and subsequence formation of n phase. Ti in IN718 superalloy also helps the formation of MC carbides and gamma prime phase. Increasing Al/Ti and (Al + Ti)/Nb will lead to form finer particles of y'. More uniform distribution of the precipitates and enhancing stability of y' in IN718 superalloy [ 4]. Adding Al to slag of ESR process can reduce the oxide inclusions because of the strong tendency of Al to oxidation. In addition, tensile properties of IN718 superalloy improve. The most significant inclusions in IN718 superalloy are Alz03 and TiN that were found in agglomerate forms. Thermodynamic calculation results indicate that the effect of increasing Al shows a strong increase in solvus while phase solvus shows mildly decrease when Al level is less than 2%, after that it dramatically decreases [ 5]. Laves phase precipitation and the appearance of phase are occurred when Al content reaches 2%. In fact, when Al content is beyond 1.5%, phase has already precipitated in a considerable scale. Shows the fraction of increases greatly while the fraction of phase decreases remarkably with the increment of Al content. Based on thermodynamic theory, if these particles were not existed in the melt during cooling agglomeration would not accrue and the superalloy will be cleaned By adding Aluminum to the slag, the metal reacts with oxyge"

Jan 1, 2013

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"Iron and steel making processes give rise to large amounts of usable and unusable materials, the latter generally being termed wastes. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. This paper defines the concept of “waste-free technology”, discusses its development in the steel industry and highlights the benefits of the technology to the manufacturing sector and the environment. The paper also articulates how the “waste-free” technology could be applied in the proposed Ajaokuta integrated steel plant in Nigeria.IntroductionIn the past, nature was considered an inexhaustible store. Its resources were consequently exploited and waste products therefrom were discarded. Today, attitudes have not changed appreciably even as raw materials cost rise by the year to pose a series of socio-economic problems, which, among others, may include the rational and optimum utilization of resources, environmental protection and reduction of waste formation. Consequently, industrialists now face unexpected regulatory pressure in areas of pollution prevention, waste minimization and hazardous waste disposal.Iron and steel making processes give rise to significant amounts of usable and un-usable materials, the latter generally being termed waste. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. In this paper, the term waste refers to those materials that are either irrationally utilized or, land-filled and part of the byproducts that are not utilized. It includes that part of used materials which is not incorporated into the products manufactured during a process stage and which in contrast to reuseable materials, is considered not suitable for any further use, owing to technical or economic factors. In general, these materials are inorganic and parts of them are either utilized or passed to the other processes; the other part should be disposed of using well-established waste disposal practices to avoid any environmental threat.Thus, creative methods must be developed to modify the manufacturing processes to reduce emissions and process wastes by fully utilizing all resources. One method of eliminating the negative effect of waste formation is the use of purification and cleaning structures (pollution control system, PCS). These are, however, quite expensive."

Jan 1, 2008

By Carl C. Nesbitt

A process has been developed to recover and recycle metals from wastes of brass foundries which contain copper, zinc and lead in various quantities. Tests were conducted to evaluate several leachants, including sulfuric acid, ammonia, hydrochloric acid, cyanide and acetic acid, and to determine the optimum leaching conditions, such as air flow rate, initial copper ion concentration, temperature, and agitation strength. Sulfuric acid containing copper sulfate with dissolved oxygen is the most successful leachant. More than 99% of the copper and zinc originally present in the waste was dissolved, while only 0.5% of the lead entered the solution after 14 hours of leaching. The leaching mechanisms of copper, zinc, and lead are proposed. The copper and zinc can be recovered from the solution by electrolytic processing. The unleached residue may be converted to a lead carbonate which can be converted to litharge at 400-450°C and to massicot at temperature above 500°C by calcination.

Jan 1, 1995

By L. W. Beckstead

In a conventional zinc refinery plant, zinc concentrates were roasted at 950°C. The calcine was ground and leached in a series of leaching vessels using sulfuric acid. The pH in the first leaching vessel was maintained at 2.5, while the pH of the solution exiting the last vessel was about 5.4. The leached residue typically contained (in percent) 0.1 Ag, 0.2 As, 0.7 Cd, 2 Cu, 15 Fe, 10 Pb, and 15 Zn, and it was classified as hazardous material according to the EP-toxicity test. In order to make the residue non-hazardous, and to recover most of the metal values from the residue, a brine leach process was developed. The process consisted of leaching the zinc leach residue in CaCI, brine solution at pH 2 for 1 hour at 90°C. Silver extraction was about 95 percent, while lead, copper, cadmium, zinc, and iron extractions were about 80, 50, 50, 30, and less than 0.5 percent, respectively. More extreme conditions of acidity could have been used in the leaching stage to increase zinc dissolution, but iron dissolution would have significantly increased which would have complicated subsequent recovery steps. The leached and washed residue passed the EP-toxicity leach test and could be disposed as non-hazardous. Silver, copper, and lead in the leach solution were recovered by zinc cementation, while zinc and cadmium were recovered by sulfide precipitation. The resulting solution can be recycled in the process after magnesium precipitation.

Jan 1, 1993

By Etsuro Shibata

The saturated solubility of chromium oxide and the valence of chromium in the slag are important matters when considering how to effectively utilize chromium-containing slags. The experimental data of various types of slags cited in the literature were arranged according to the optical basicity in order to evaluate the effects of the oxygen potential and the slag composition. The saturated solubility of chromium oxide and the Cr2+/ Cr3+ ratio tend to decrease with the increase of the optical basicity of the slag at an oxygen potential below 10.5 atm. However, at an oxygen potential of 0.21 atm, the saturated solubility and the Cr6+/Cr3+ ratio tend to increase with an increase of the optical basicity. A practical approach was suggested to reduce chromium in the stainless steel slag and simultaneously recover it as a ferroalloy by the direct smelting reduction of chromium oxide in the molten slag using some reductant in a small furnace.

Jan 1, 2003

By Donald R. Fosnacht

An investigation was initiated to obtain the scope of the problems associated with recycling various waste oxide materials generated at Inland Steel and to identify and? test techniques that could possibly aid in increasing the amount of waste oxide materials recycled to primary. operations. Based on the results of this work, several new techniques were developed ?and tested on ?a plant or laboratory scale. These include the use of cold-bond agglomeration methods for producing waste oxide agglomerates for use as a cooling agent or scrap substitute in steelmaking operations, and the use of various techniques for beneficiating blast furnace flue dust and soaking pit rubble so that the upgraded materials can be utilized in sinter plant or ironmaking operations. The physical and chemical characteristics of the waste oxide materials and the results of the laboratory and plant testing are discussed in this paper.

Jan 1, 1985

By Ann E. Visser

Aqueous Biphasic Systems (ABS) form upon the admixture of certain water-soluble polymers or polymers and salts above critical concentrations, and thus represent liquid/liquid extraction systems whose nature is entirely aqueous. We are currently investigating the utility of ABS (and its solid phase analogs) as "green" alternatives to the use of volatile organic diluents in separations of metal ions. Chaotropic (water-destructuring) metal ions with small negative AGhyd (e.g., Tc04) tend to partition quantitatively to the PEG-rich phase of an ABS, but even hydrated metal cations can be partitioned to the PEG-rich phase if a suitable extractant (e.g., halide, dye, crown ether, etc.) is used to produce a more chaotropic ion-complex.

Jan 1, 1999

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By Peter Stiaszny, Andrej Samoilov, Yuri Titovets, Gottfried Hribernig, Nikolai Zolotorevskii

"The model has been developed to simultaneously predict both transformation product portions and mean ferrite grain size from the same common · principles as a result of the austenite decomposition during any cooling path of dual phase steels. The transformation products considered are polygonal ferrite, pearlite, bainite and martensite. The model is based on the classical equations of nucleation-growth theory and also contains some empirical parameters. The chemical driving forces for nucleation and composition of elements at the phase interfaces are derived by computation thermodynamics. The empirical parameters related to the model were determined on the basis of a series of austenite transformation dilatometric curves and grain size measurements for continuous and interrupted cooling of several steel types. The model is aimed to predict phase transformation in the complex cooling conditions of the run-out table of the hot strip mill at YOEST-ALPINE STAHL LINZ GmbH as a part of the computer aided system for prediction and on-line controlling of the mechanical properties of hot-rolled strip.IntroductionThe term ""dual phase steels"" is used to refer to a steel consisting essentially of a dispersion of martensite in a fine-grained ferrite matrix. These steels are of increasing technological interest since they provide a better combination of strength and ductility than any other conventional steel sheet material. The strength is important because it offers an opportunity to produce lighter components, while good ductility is needed to permit easy forming of components. It is generally recognized that martensite plays an important role in determining the strength level of dual phase steels. A full understanding of the role played by the phases in determining such characteristics requires investigating in more detail how to optimize the martensite level of such steels, while maintaining good ductility remains the subject of continued research in the industry."

Jan 1, 2000