Search Documents

By H. Cui

Rapid technological development has caused an increase in the demand for rare earths. Ancylite, a strontium rare earth carbonate, is a potentially significant source of rare earths. In this research paper, essential aspects of the magnetic separation and flotation processes for Bear Lodge ore are presented. A flowsheet is proposed based on an optimization of the variables and flotation simulation. The economic feasibility of the proposed processing operation is analyzed.

By D. E. Woolley

The rate of reduction of iron oxide from calcia-silica-alumina slag by carbon in liquid iron has been measured over the temperature range 1400-1600°C by monitoring the rate of carbon monoxide (CO) evolution. Slags containing ferric iron have been used in order to study the reduction of both ferric and ferrous cations. Results show that ferric iron is reduced before ferrous iron, so that the ferrous iron concentration increases initially. It is also shown that the rate constant, k, decreases at low reaction rates, or, equivalently, at low concentrations. The authors conclude that the reaction occurs in two periods. During the first period, ferric iron is reduced to ferrous iron. During the second period, ferrous iron is reduced to metallic iron, and the rate-limiting step during the second period is the mass transfer of ferrous cations in the slag phase to the slag-metal interface.

Jan 1, 1998

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothermic reduction, hydro metallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of alloying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an alloy.

Jan 1, 2003

By Richard D. Hangi

Process mineralogy techniques are uniquely applicable to industrial problems related to the extractive metallurgy of nickel, cobalt, and associated metals. Reflected 1ight microscopy, together with selected determinations by scanning electron microscopy-energy dispersive spectrographic analysis and electron probe microanalysis, provides the means to identify the ore minerals cobalt and nickel ores, determine the abundance of each ore mineral, assess the extent of intergrowth between the cobalt and nickel minerals and other ore and gangue minerals in the ores and concentrates, and predict the potential success of cobalt and nickel extraction by grinding, flotation, pyrometallurgical, and hydrometallurgical treatments. In addition, the extent of locking of the cobalt and nickel minerals with each other and with the gangue minerals can be directly observed by reflected light microscopy. Where ores have been treated by hydrometallurgical procedures, reflected light microscopy can serve to determine the causes of excessive leach consumption. Finally, the partitioning of cobalt and nickel between high-temperature synthetic phases produced by pyrometallurgical treatment can be precisely determined by process mineralogy techniques. Case histories from cobalt and nickel deposits illustrate the value of applied mineralogical techniques in the study of cobalt and nickel ores, beneficiation, hydrometallurgial, and pyrometallurgical products.

Jan 1, 1993

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of aJ10ying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an aJ1oy.

Jan 1, 2003

By George P. Demopoulos

n this study we have sought to highlight the critical linkage between individual reaction kinetic parameters (usually determined in small bench scale experiments) and large continuous reactor performance by focusing on the industrially significant zinc pressure leach process. To this end a comprehensive mathematical model previously developed for the description of this process was employed. In this paper we have examined in particular how small variations in key kinetic parameters impact on the autoclave&apos;s performance, i.e. attainment of autogenous steady-state temperature, zinc conversion and solution chemistry. The reaction parameters studied were: (i) stoichiometry of the marmatite leaching reaction; (ii) the activation energy of the same reaction, E,; (iii) the rate constant of the ferrous to ferric oxidation reaction, k,; and (iv) the apparent equilibrium constant for ferric precipitation, K,. This parameter sensitivity analysis was done under no oxygen mass transfer control limitations. Model predictions were found to be more sensitive to the kinetic parameters under certain conditions than others. The most dramatic finding was the one related to the small amount of sulfate produced during marmatite leaching. In connection to this it was found that the small percentage (< 5 %) of sulfate produced enhances the autothermal operational stability of the autoclave. The need for accurate kinetic parameter determination under conditions similar to those encountered in industrial zinc pressure leaching was demonstrated.

Jan 1, 1999

By G. R. Palmer

The success of future electric vehicles will depend greatly upon the power supply choices made today. Research is presently being conducted by automotive engineers and electrochemists to determine what battery type may be the most promising. Not only are product production and application efficiencies being evaluated but also environmental concerns of reclamation and recycling. Rechargeable batteries using nickel-metal hydride electrodes are strong candidates for these electric vehicle applications. The U.S. Bureau of Mines is investigating hydrometallurgical technology that separates and recovers purified metallic components present in nickel-metal hydride battery scrap. Sulfuric, hydrochloric, and nitric acids are all capable of dissolving the battery electrode alloys given the proper operating conditions. Solvent extraction of the leach solutions using D2EHPA removes iron, and selective precipitation shows promise of recovering the other metals in the H2SO4 and HNO, systems.

Jan 1, 1994

By Walter E. Dean

Twenty six samples of carbonaceous gold ores and associated rocks from outcrop and mine localities in northcentral Nevada were analyzed for concentrations of major. minor, and trace elements, total sulfur, and organic carbon. Q-mode factor analysis was used to define six distinctive carbonate, organic, and detrital associations of elements, and to group samples based on these associations. The trace metals that have clearly enriched the organic-carbon-rich samples are V, Zn, Ni, Cu, Cr, and Mo, although few of the samples could be considered "metal-rich" when compared to other organic-carbon-rich black shales. Rock-Eval pyrolysis was used to evaluate thermal maturity and hydrocarbon yield of the samples. Unfortunately, most samples were too thermally altered to be suitable for routine organic geochemical characterization of organic matter. The 813C values of organic carbon in rocks from different deposits have a trimodal distribution, but there is no clear distinction between the three groups of deposits that can be related to age, thermal history, or depositional environment.

Jan 1, 1987

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By C. M. F. Vieira

The main characteristics and physical and mechanical properties of clays from the county of Campos dos Goytacazes, located at the northern part of the State of Rio de Janeiro, Brazil, are presented. The characterization included mineralogical composition, chemical composition and particle size distribution. The properties related to water absorption, linear shrinkage and flexural rupture strength were obtained in samples that were prepared by 20 MPa uniaxial pressing and fired at 950 and 1100oC. The results showed that the clays are predominantly kaolinitic with high percentage of clay minerals. The kaolinitic structure associated with a small amount of fluxes confers a refractory behavior which makes difficult the sinterization and impairs the ceramic consolidation.

Jan 1, 2009

By A. L. Paverd

The petrology of a number of pyrometasomatic mineral deposits in north Queensland, Australia, were studied to evaluate the use of mineralogy and major element chemistry in the exploration for copper, lead and zinc-bearing skarns. Results indicate a direct correlation between the character of the mineralization and the composition and nature of the host rock. The study of garnet compositions proved the most useful. Economic mineralization was limited to limestone-derived skarns containing garnet of And60-90, whereas skarns containing garnet of less than contained less than 1And55 contained less than 1% total sulfide. Skarns containing garnet of And60-8S host the best mineralization; above And8S&apos; copper, lead and zinc sulfides decrease and magnetite and pyrrhotite become the dominant ore minerals. Similar correlations were found for pyroxene, amphibole and &apos;the bulk composition of the skarns.

Jan 1, 1981

By Kimio Itagaki

The distribution behaviours of the VA elements between the gas, slag and matte phases in copper smelting were evaluated on the basis of the thermodynamic data, most of which were determined by the authors. The distribution is basically dependent on the process factors such as temperature, the content of the element in charge, the amount of the waste gas and degree of vapour saturation with the elements. The thermodynamic quantities such as the activity coefficients of the VA elements in matte, the activities of iron and copper, SO2 or 02 potential and the distribution ratio of the elements between the slag and matte phases seriously affect the distribution, and the behaviours in various smelters could be explained systematically and reasonably by considering the changes in these quantities, In oxidation smelting at PSO2= 0.1 to 1 atm, the proportion of arsenic and bismuth in gas is predomi22t for the arsenic and bismuth distributions in both smelting and converting stages. The degree of vapour saturation has serious effect on the distribution, and sufficient contact between gas and matte phases is desirable for transferring arsenic and bismuth into gas phase.The elimination of antimony by means of vaporization is not significant. In reduction smelting at po2 = 10-11 atm, the proportions of arsenic and antimony in the gas phase are quite small, but the proportion of bismuth does not change significantly.

Jan 1, 1983

By F. Leuzzi

Asbestos is a natural mineral fibre which has been known and utilized commercially for about a century. From the forties, it was employed on an ever-increasing scale throughout the mechanical engineering, building, paper-making and plastics sectors, to name but a few. There are essentially five minerals which provide fibres for industrial applications, namely, the chrysotile variety of serpentine and the amphiboles such as riebeckite, anthophyllite, cummingtonite-grunerite (amosite) and tremolite. About a fifth of the world&apos;s asbestos output was once taken by Europe for the manufacture of asbestos-cement products, reinforced plastics, paper and cardboard, panels, soft insulation and spray-on powders. However, in the sixties and seventies the hypothesis regarding the pathogenic nature of asbestos fibres started to gain ground. Moreover, between the sixties and eighties the EU issued a series of regulations designed to bring about a steady decrease in asbestos consumption. This line of action has culminated in recent years in a whole set of directives banning the use of asbestos in all products. This created a major problem, namely, how to clean-up the several million tons of various types of asbestos products in various states of conservation existing in Western Europe. CORDIAM (Pat. RM95 A 000269 and Pat. RM96 A 000782 in the name of ECOTEC S.r.1.) is one of the thermal inertization techniques recently proposed for this purpose. The process provides for the low-temperature ceramization of the toxic-harmful material. Of course, with such a great variety of waste materials and the volumes to be treated, as well as the need to ensure the correct dimensional design of the thermal sections of the treatment plant, it is necessary to know as much as possible about the thermal behaviour of the wastes concerned. This paper details the steps taken firstly to ascertain the thermal behaviour of such materials as may be encountered in day-to-day practice and secondly to examine the influence of the main process parameters on the preliminary design of gas- or fuel-oil-fired rotary kilns of the kind used for waste treatment.

Jan 1, 1999

By S. Ozbilen

"Al-Li binary alloys with nominal Li contents of0.15, 1.1and2.8 (in wt%) were aged naturally at room temperature for two months, aged at low temperatures ( 65 and 1 OOEC) for up to 2 months and aged artificially at 190EC for 4 days after water quenching to 25EC following solutionizing at 530EC for 20 minutes. Ageing behavior of these binary alloys were studied by Vicker's Hardness measurements and DSC thermal analysis. Thermal analysis results indicate the formation of GP zones of Al-Li system in Al-2.8wt%Li binary alloy. In the same alloy, rapid quenching from one phase region (a) gives rise to precipitation of small o' particles in a matrix (a) with still high supersaturation. During ageing of this alloy below lOOEC an additional transformation, i.e., GP zone formation occurs proceeding at a very high rate which is described on the basis of the theoretical analysis for the quenched Al-Li system proposed by Khachaturyan et al [6]. Ageing at temperatures below 11 OEC takes place slowly by the formation of small d' particles of lower thermal stability than the quenched-in d precipitates in addition to GP zones resulting in an increase in hardness compared to water quenched samples. During artificial ageing, GP zones transform by dissolution to d' precipitates while d' particles already in the microstructure coarsen during under aged condition at which hardness increases with time till peak aged condition.IntroductionIn binary Al-Li alloys the d' (Al3Li) fully coherent internally ordered inetastable phase of Li2 structure with a=0.4038d [1-5] forms homogeneously between 120 and 190EC before the formation of stable d' (A!Li) phase and cause the superior mechanical properties. This is due to an appreciable age hardening effect resulting because of the d' precipitation during ageing [1]. The response of d' to decomposition and its formation kinetics have been studied previously and it is believed that the decomposition of the a-supersaturated solid solution occurs in a two stage process; i.e., a 6 d' (Al3Li) 6 d(A!Li). Khachturyan et al [6] theoretically investigated precipitation of the d' phase and gave an interpretation of the transformation paths of the quenched Al-Li alloys. They predict that the disordered supersaturated solid solution congruently orders, and then the uniformly ordered solution decomposes into ordered regions that differ in Li-content. Finally, ordered d' phase forms in the disordered matrix."

Jan 1, 1998

By Aïda Espinola

Decontamination of synthetic solutions containing cadmium ions using coconut fibers in natura was investigated in laboratory scale. Cadmium ions, a serious pollutant of water ways, where it is detrimental to the environment, may be absorbed by fish and mollusk used as food, which will, eventually, poison humans; these ions are usually present in minero-metallurgical and electroplating industrial effluents. Usually employed for the aqueous effluents treatment are chemical precipitation, adsorption and electrolytic processes. Precipitation is not effective for cadmium removal, because of the high KpS of the cadmium hydroxide, which requires high pH; only sulfide would be efficient in cases of very small amounts. Some vegetal refuses have shown to be practical for absorption processes of several metallic ions. We have applied coconut (Cocos nucifera) shells, which are extremely abundant over most of the extensive Brazilian coast, in the removal of cadmium: it has been verified, in our laboratory, that the surface of the fiber of this coconut is rich in chemical compounds which are active scavengers for Cd2+. For the optimization of the process, hydrosoluble components existing on the surface of the fiber, which may be deleterious, were previously washed out by water, and variables, such as the pH and the proportion of mass of fiber to volume of solution, were adjusted. As much as 99% of the initial contaminant metallic ion has been eliminated, resulting a solution to be discarded which contains ca. 0.1 ppm; this attends to the maximum impurity legally admitted by the environmental control agency of Rio de Janeiro, FEEMA, for cadmium ions in aqueous effluents to be disposed in rivers and in the Guanabara Bay area.

Jan 1, 1998

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003