Search Documents

By Neil D. Donnell, O&apos

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely-spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an ore body block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1985

By R. A. Hevia

Florida Power and Light is the fifth largest investor-owned electric utility in the country. It has a service territory that covers 35 counties, or 28,000 square miles, 2.5 million customers, and serves 5.6 million people. The total installed capacity is 13,470 MW, generated by four nuclear units, 36 oil and/or gas fired units, and 48 gas turbine units. Traditionally, FPL has been an oil-based utility. In 1979, this dependency on oil became obvious when 42 million barrels of oil were burned during the year. At that time, it was also projected that, based on the current estimates of customer growth and available generation capacity through 1990, FPL's residual fuel oil consumption would increase from the 1979 level of 42 million barrels (6.7 million m3) per year to approximately 55 million barrels (8.7 million m3) per year by the mid-1990's. Concern over this was further aggravated by the fact that it was difficult to estimate both the price and quantity of fuel oil that would be available over the next decade since changes in the world market, decisions by oil producers and refiners, and international political developments would all affect the availability of oil. Also, at that time, the price of residual fuel oil had increased drastically, and there was no reason to think that these prices would soon stabilize. Thus, oil back-out became a primary objective of FPL and since then, FPL has been actively investigating ways to decrease fuel oil consumption.

Jan 1, 1985

By Richard J. Wilson

The importance of coal as a major source of energy used by the steel industry has been increasing due to the gradual changeover from steel- making by the open hearth process to steelmaking by the basic oxygen process. Since the production of steel by the BOF process increases the demand for hot metal, there is a growing need to ensure the supply of coke required for the production of hot metal. Coal used for cokemaking has become, therefore, an increasingly important raw material for the steel industry in recent years. Our current projections indicate that coal will be the source of 71% of the total energy requirements of Inland Steel Company in 1985. As a result of the energy shortages of the last few years, various conservation programs have been initiated by the steel industry to reduce the consumption rate of fuel. The efforts to conserve energy have been successful to a great extent due to the rapid advances made in the technology of ironmaking that facilitated gradual reductions in the quantity of coke used per ton of hot metal produced in the blast furnaces. The decrease in the consumption rate of coke was made possible by the use of improved raw materials, such as iron ore pellets and fluxed agglomerates, the operation with high blast temperatures, the injection of auxiliary fuels, and the enrichment of the blast with oxygen. It is expected that additional reductions in the fuel consumption rate will be possible in the ironmaking operations of the large blast furnaces that are being equipped with facilities for proper burden distribution and for operation with higher blast temperatures at high top pressure. The purpose of this paper is to show the effects of coke quality on the production of BOF steel. The importance of coke quality will be pointed out by discussing the effects of the physical strength of coke on both the blast furnace productivity and the steelmaking operations of an integrated steel plant, such as Inland Stee1 Company.

Jan 1, 1980

By M. P. Corriveau

This is the case history of how two nearby plants in Southwest Virginia solved their water clarification problems. While the solutions should not be considered applicable industry-wide, the methods used in arriving at the answers deserve consideration. When Clinchfield's Moss No. 2 Preparation Plant, the first ever built in Tiller Seam coal, was started in the fall of 1956, the clays in the raw coal soon posed a flocculation problem, Laboratory sedimentation tests were initiated; and as a result, lime was adopted as the flocculant for the clays, With lime, a pH of 11.2 was required. As the plant tonnage increased, it became evident that the amount of coal fines produced in the mining and preparation was greater than had been estimated and that the 90-foot thickener was inadequate in providing sufficient settling time to effect a clarified overflow for reuse. Testing showed that Separan 26105 (NP10)1/, when used with lime, was the most satisfactory coal flocculant available,

Jan 1, 1960

By Andrea Biagi, Elisa Comis, Gianluca Bella, Enrico De Panicis, Guido Barbieri, Matteo Giani

The Sotra Link Project is a major infrastructure project in Norway involving the design, construction, financing and maintenance of several underground and surface structures between Sotra island and the city of Bergen, among them 23 tunnel portals, 12.5 km of tunnels and a 900 m long suspension bridge. This paper describes the benefits in applying a Building Information Modelling (BIM) approach to tunnelling, from Early Design to the Detail Design Phase. The BIM application to the Sotra Link Project resulted in several improvements, such as efficient handling of clashes and inconsistencies, deeper understanding of effective design choices (reduction of errors), more efficient communication between designers, enhanced control of project quantities and costs. The advantages of the BIM approach during the ongoing Construction Phase are also explained.

Jun 23, 2024

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By Dale W. Norris, John A. L. Campbell

INTRODUCTION Optimization, as measured by productivity gains, is being achieved in our nation's preparation plants principally by automation, economy of scale, and reducing maintenance. Increased tonnage per unit of investment, a1 so a measure of optimization, is being achieved by breaking with tradition and increasing plant utilization, while simultaneously improving on equipment re1iabi1ity. Improved qua1ity, another measure of optimization, is being attained through technical innovation. This review will concentrate on state-of-the- art unit operations and processes, and will not discuss emerging new technologies which are covered in detail in other presentations of this symposium. It is recognized that much of what will be discussed in this paper is not unique to the fine coal circuit, but is equally applicable to the entire preparation plant. However, the areas reviewed are the principal means being used today to optimize an existing preparation plant's fine coal circuit. Prior to designing and optimizing a fine coal cleaning circuit, the question that must first be answered is, "Do we even want a fine coal circuit? This is a much more complex question than is readily apparent, as most of you recognize. It can be argued either way. In the final analysis the "bottom line" will hold (Blackmore, 1982). If your sales contract a1 lows it, and the selling price can justify it, you most assuredly want to build a fine coal circuit into your preparation plant. In general today, most new preparation plants do have fine coal cleaning circuits. The purpose of fine coal cleaning has changed with time. Some of the early applications of fine coal cleaning were to prevent stream pollution rather than to prepare a product for market (Merrill a Pennington, 1962). During the 50's, 60's and into the 70's the principal thrust of fine coal cleaning was in metallurgical coal preparation. More recently, the emphasis of the 80's is on steam coal processing. There is no consensus on what is fine coal. Traditionally, fine coal would be anything below 1/4" in size. Because of the advances being made in intermediate coal cleaning processes, i.e. heavy media cyclones and jig cleaning, this discussion will define fine coal as -28 mesh (Aplan, 1987). Figure 1 is a plot of the size ranges of a large number of U.S. bituminous coals. In general the -28 mesh fraction of a bituminous coal will be between 7% and 18% of the ROM feed with reported ranges of 5% to 40% (Aplan, 1987). Consequently, traditional fine coal cleaning is general 1 y involved with a re1 actively mi nor portion of the coal feed. Every effort is taken both in terms of mining and preparation to keep it that way because of the high cost of cleaning fines. The move away from this posture, namely, the techniques to fine grind coal to liberate pyrite is probably the biggest challenge facing fine coal processing today.

Jan 1, 1988

By Gleason

"From June 16 to 19, more than 1,400 tunneling and underground construction professionals gathered in Chicago, IL for the bienial Rapid Excavation and Tunneling Conference (RETC). There, they were greeted by a full technical program and an exciting exhibit hall that provided a comprehensive look at the world’s bustling tunneling and underground construction industry.The successful conference was a reflection of the industry itself, which is to say, busy. As much of the world has begun to focus on creating a cleaner and greener environment, the global tunneling industry has seen an uptick in infrastructure projects move from design-build to construction phase. With a global shift away from the use of fossil fuels, major cities around the world are looking to increase public transportation options, which leads to the need for more transportation tunnels. And as urban populations continue to grow, the need for clean water calls for more tunnels, and as urban footprints continue to expand, the need to increase and update combined sewage overflow tunnel grows with them.During two and a half days, more than 20 sessions covering all of these topics were presented at the Hyatt Regency in Chicago, many to packed rooms in which every seat was taken and people were standing along the side and back walls.RETC is a biennial conference and one of the largest in the North America for the tunneling and underground construction industries. As such, it hosts a robust exhibit floor. This year 172 vendors occupied 205 booth spaces. The exhibit included everything from tunnel boring machine manufacturers, like Robbins and Herrenknecht, to the companies that supply all kinds of parts and services to the industry."

Sep 1, 2019

By G. Michael Lloyd

The term phosphate beneficiation often conjures up visions of processing technologies that physically separate the phosphate rock from some impurity and do not result in a change in the chemical nature of the phosphate rock. However, when we consider hydrometallurgical processing as a phos¬phate beneficiation technique we have to include all chemical treatments that convert phosphate rock into a more useful product. With most of the phosphate rock mined being used for fertilizer pro¬duction, the best known and most widely employed hydrometallurgical process is wet process phospho¬ric acid manufacture. In general, all phosphate rocks are so insoluble that there is no physical treat¬ment that will allow the phosphate content to be used by vegetation in a timely manner. However, after chemical treatment, 100% of the phosphate is readily available for vegetation nutrition. If there is a chemical beneficiation process that could be considered the standard method of treat¬ing phosphate rock it would have to be the wet pro¬cess for phosphoric acid production. In this process finely ground phosphate is reacted with sulfuric acid to give phosphoric acid and phosphogypsum. The phosphogypsum crystals are removed from the phosphoric acid solution and discarded; the phos¬phoric acid is further processed to give the finished fertilizer product. The primary reason that this pro¬cess was adopted so widely is because the phosphogypsum solid that is formed can be easily separated from the phosphoric acid, thereby removing the calcium portion of the phosphate rock and the sul¬fate portion of the sulfuric acid. Other acids have been used to treat phosphate rock but nitric acid is the only other acid used commercially. Nitric acid gives a mixture of phos¬phoric acid and nitrates that can be further pro¬cessed into N-P fertilizers, but the range of N/P grades that can be produced is limited. Hydrochlo¬ric acid has been used to react with phosphate rock, and it can be used to generate a pure phos¬phoric acid but only after solvent extraction to separate the calcium chloride from the phosphoric acid. And then there is the problem of what to do with the calcium chloride. The acid that has received the most attention as a substitute for sulfuric acid is phosphoric acid. In this process, the phosphoric acid reacts with the phosphate rock to give a mono-calcium phosphate solution. This process does not dissolve all the impurities in the phosphate rock, and these solids can be removed from the solution before sulfuric acid is added to convert the soluble calcium to insoluble phosphogypsum. Despite all the claimed advantages, this process has not found favor. A suc¬cessful application of this process to treat some of the lower grade phosphate rocks being used today would seem to have some distinct advantages. Other beneficiation schemes have been pro¬posed or practiced on specific phosphate rocks on a limited scale. These include calcination followed by water leaching to remove lime, weak acid

Jan 1, 1999

By Joseph M. Hans

INTRODUCTION The decontamination of a uranium mill site is principally an earth moving task. The task can be completed effectively and efficiently by selecting the proper earth moving equipment and using that equipment within its particular constraints for decontamination work. A considerable backlog of experience concerning earth moving equipment selection and use was acquired during the decontamination work conducted at the former Shiprock, New Mexico, uranium mill site. This experience was acquired by trial and error while decontaminating over a wide range of depths and different types of terrain. Many different types of excavation equipment were available to the Shiprock decontamination project because the Navajo Engineering and Construction Authority (NECA) heavy equipment operator's school was doing the decontamination work and a variety of equipment was needed for training. The equipment is described and its general use for decontamination is discussed. Its on-the-job use for decontaminating the Shiprock millsite is presented. [EARTH MOVING/ANCILLARY EQUIPMENT DESCRIPTION AND DECONTAMINATION CONSTRAINTS] Tractor-Scrapers The most commonly used scraper is the bottom-dump type because it is highly mobile and can dig, carry, and spread loads. In this type a tractor is connected with a yoke to a scraper bowl (Figure 1). The bowl is essentially a rigid box that pivots around the rear axle, opening to the front. A hardened steel knife, or bit, is attached to the leading edge of the bowl. When scraping, the bit penetrates and forces the earth overlying the bit edge into the scraper bowl as the scraper moves forward. When the bowl is full, it is closed by lowering a closure or apron against the cutting bit. The load is dumped while moving, by raising the apron and forcing the load from the bowl with a crowd, or ejector. The height of the dumped load is controlled by adjusting the bit height when dumping. Scrapers of this type generally do not have enough power to scrape up loads unassisted. Loading assistance is generally provided by a crawler tractor that pushes from the rear against the scraper's push block. Some scrapers are made self-loading by adding an additional engine for the extra power needed for the load pick up. Another commonly used self-loading scraper uses a loading elevator (Figure 2). The elevator consists of two roller chains carrying crossbars. The elevator is rotated when scraping and the crossbars cut the earth above or in front of the bowl bit, forcing the load into the scraper bowl. No apron is used on elevating scrapers. The load is dumped by partially retracting the bowl floor and pushing with an ejector. Scrapers have some undesirable characteristics when used for decontamination work. One characteristic is that a clearance space exists around the apron when it is in its closed position. Part of the load (especially sandy soils) dribbles through the

Jan 1, 1981

By F. L. Pirkle

A heavy mineral deposit about 1.6 km (1 mile) in length, 0.13 km (0.08 mile) in width and averaging about 3 m (10 ft) in thickness is exposed approximately 130 km (80 miles) east of Denver, along Interstate 70, in Elbert county, CO near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium ridge. The dominant heavy minerals, accounting for about 70% of the total heavy-mineral suite by weight, are ilmenite, garnet and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Ga. Thus, Titanium ridge provides evidence that heavy-mineral accumulation models for late cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2012

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By R. Bishop, J. Baggett, J. Monsalve, N. Ripepi, A. Soni

Technology plays an ever-increasing role in improving the safety and efficiency of mining operations. Laser scanning and photogrammetry are two useful methods for capturing 3D digital representations of real world objects. While both technologies have been applied to the mining industry in numerous ways, the practical applications in an operating underground limestone mine has been tested for this paper, including for visualization and site characterization. Each technology is capable of creating highly detailed geospatial point clouds, but are all point clouds created equal? This paper presents a comparison of a laser scan and photogrammetry of a limestone pillar and addresses the strengths and limitations of each method for creating digital models of operating underground limestone mines. INTRODUCTION The United States crushed stone business is a ~$14 billion per year industry representing 1,430 companies which operate 3,782 mining operations across the 50 states. In 2017 alone, 1.33 billion tons of crushed stone was produced with 76% used predominately for road construction and repairs, but also for the production of cement, lime, chemical and agricultural uses. Over 70% of domestic crushed stone producers source their material from limestone and dolomite deposits, with currently only 82 mines (2%) operating underground (USGS, 2018). Underground mining requires a different technical skillset, and poses great challenges for production that must be both safe and economical. Therefore, there are many risks that an operation must mitigate in order to produce underground limestone. Some of the challenges in underground limestone mining involve geological hazards that are unique to the rest of the industry. The geologic features such as faults and weaknesses can be difficult to assess in a production environment (NIOSH, 1998). The consequences of failure due to improperly designed underground mining ground support systems, such as from a roof failure, are not only life threatening for the miners themselves, but can easily shut down an entire mining operation.

Jan 1, 2019

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

El modelamiento de la dinámica de fluidos computacional (CFD por sus siglas en inglés) implica la creación de un dominio de cálculo llamado malla o rejilla para resolver las ecuaciones que definen la física del flujo de fluidos. Este proceso comprende a menudo emplear la mayor parte del tiempo en esfuerzos de modelamiento. En un proyecto patrocinado por el Instituto Nacional de Seguridad y Salud Ocupacional (NIOSH), los investigadores de la Escuela de Minas de Colorado utilizaron un enfoque innovador de mallas, el cual permite una fácil adaptación del modelo CFD para adaptarse a una variedad de geometrías de minado de tajos largos ventilados por canales (bleeders) y progresivamente sellados (referidos a menudo como bleederless en los Estados Unidos), con la porosidad y la permeabilidad de la cámara escalables en un amplio intervalo. En este trabajo se presenta la metodología del enfoque de enmallado y escalado junto con las recomendaciones para el uso de modelos CFD en aplicaciones de ventilación para las cámaras en tajos largos. La nueva técnica de enmallado se utilizó para evaluar la función de un retorno hacia atrás en una cámara progresivamente sellada y otra cámara ventilada por canales.

Jan 1, 2014

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

Computational fluid dynamics (CFD) modeling involves the creation of a computation domain called a mesh or grid to solve the equations defining the physics of fluid flow. This process often comprises the majority of time spent in modeling efforts. In a project sponsored by the U.S. National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of longwall bleeder-ventilated and progressively sealed (often referred to as bleederless in the United States) mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob and a bleeder-ventilated gob.

Jan 1, 2014

By John L. Stafford

The ROEMMC combustion system was originally conceived as a means of utilizing solid fuels that would otherwise have been wastes requiring disposal and convert these fuels into useful energy sources. This concept follows as an extension of the application of residual waste incineration with energy recovery practiced in the lumber, manufactured board, sugar cane, and other industries. The incineration of these wastes in the furnaces of steam generating equipment is thoroughly described (1, 2, 3, 4, 5, 6, 7). The fundamental principle of the ROEMMC system is temperature control which makes possible the maintenance of the non-combustible fraction of these solid fuels in a dry solid state and their separation from the gaseous products of combustion. This philosophy of ash removal and the "slagging" philosophy are compared. The ROEMMC equipment function and applications are described.

Jan 1, 1978

By George White

On June 25, 1876 Lt. Colonel George Armstrong Custer led the Seventh U.S. Cavalry Regiment., comprising 31 officers and 637 enlisted men, into the valley of the Little Big Horn River in southern Montana. His assigned mission was a reconnaissance-in- force to locate the Indians reported to be assemblying in that area. Custer was extremely successful in locating the Indians. Unfortunately he located more than 3000 Cheyenne and Sioux under the leadership of the great war chiefs Crazy Horse and Gall. Custer's entire battalion of more than 200 men was annihilated; there were no survivors. While I don't seriously suggest that things will be all that bad in the uranium industry, I do suggest that some very fundamental changes have occurred in the uranium market. Conventional thinking based on past truths will no longer suffice. Geology, economics, politics, nuclear growth pat terns, technology, and utility attitudes have all changed. New thinking is in order. It is at this point that I would offer my usual disclaimer. My views regarding the future are simply that--my personal views. My belief that certain events will come to pass does not mean I view those events as appropriate, wise, good, equitable, or economic.

Jan 1, 1985

By John R. Hawley

Ontario, one of the richest mining districts in the world, is a natural storehouse for much of the earth's fresh water supply. Covering over 344,000 square miles, the surface of this Canadian Province is dotted with 250,000 fresh water lakes and is laced with uncounted thousands of fresh water rivers and streams. The southern portion of the Province, for the most part, is flat or lazily rolling farmland. This is where most of the people in Ontario live. Although it is not a major mining area, southern Ontario does possess important deposits of salt, oil, gas and gypsum. Most of these deposits are being actively worked. Toronto, the capital city of Ontario, lies deep in the southern region. Here the climate is mild and the winters are short. The total annual precipitation consists of 27 inches of rain and 65 inches of snow. Most of the major mining companies that do business in Canada have made Toronto their Canadian headquarters. There are two reasons for this. The first, of course, is money. Toronto is the gathering place of many well- known financial institutions. The second is access. Toronto lies within a few hundred miles of some of the most spectacular mining enterprises that exist in the world.

Jan 1, 1973

By Yao Zhou

Under the United Nations Convention on the Law of the Sea (UNCLOS), the international seabed area (Area) and its resources are the common heritage of humanity (CHH). Patent rights can be incompatible with the CHH doctrine and its underlying principles because patent holders might charge unjustifiably high prices to license patented technology for exploring and exploiting the Area’s resources (creating a "patent holdup" situation), might choose not to license, or might license exclusively when doing so would contravene CHH principles. However, a reasonable patent licensing regime can contribute to sharing the benefits derived from the Area and promote environmental sustainability. Provisions of the UNCLOS that stipulated compulsory technology and financial transfers were removed in the 1994 Agreement relating to the Implementation of Part XI of the UNCLOS (1994 Agreement), but to promote equity and sustainability I propose a voluntary licensing regime modeled on the concept of reasonable and non-discriminatory patent licensing (RAND) that has been used in other contexts. The International Seabed Authority (ISA) or another entity will need to coordinate and promote this licensing regime through governance of intellectual property (IP) derived from the Area. This proposed approach can better effectuate the CHH doctrine and its underlying principles.

Sep 1, 2014

By Xingang Wang

Spontaneous combustion is one of the most important safety issues in the global coal industry. It is considered to be a trigger for explosions in underground mines, especially for gassy mines. This thermal event is not easily detectable in the gob and sealed area. It is also a tough job to find the most likely hot point accurately. Admittedly, determination of the propensity for spontaneous combustion before mining activity should be a necessary step in the design of a mine and ventilation plan. However, due to the complexity of the chemical and physical properties of coal, spontaneous combustion has not been fully understood. According to a proximate analysis of coal, it is believed that sulfur and volatile matter in coal are the main intrinsic factors that cause the self-heating of coal. Their oxidation at lower temperatures than that of fixed carbon to initiate coal?s self-heating should be quantified. This study aims to improve the previous mathematical model developed by the authors for studying a coal?s propensity for spontaneous combustion. It enhances the model?s ability to consider the effects of sulfur, volatile matter and moisture content in the coal ? three important factors affecting a coal?s self-heating process. Based on the law of energy conservation, heat release rates for pyrite oxidation and moisture condensation are built into the model. Finally, the simulation results in terms of time versus temperature are calibrated with adiabatic testing data extracted from the literature for pyrite oxidation and moisture condensation, respectively. From the modeling results, it is found that the higher the pyrite content the coal contains and the more moisture that condenses in an environment with high relative humidity and initial temperature, the higher the potential for spontaneous combustion.

Jan 1, 2014