Search Documents

By G. Kazonich, S. L. McGill, J. W. Walkiewicz

Naturally occurring minerals and reagent-grade compounds were tested to determine their receptivity to microwave heating. The maximum temperature achieved for the samples and the time required to reach temperature are reported. A description of the microwave oven and a thermocouple technique that accurately measures and continuously records the temperature of samples during irradiation are reported. Extractive applications using the generated microwave data were investigated. Stress fracturing at mineral grain boundaries in a gangue matrix was shown. This should significantly affect grinding energy requirements and liberation properties. A method to produce a magnetic phase on pyrite surfaces, a method of using microwave heating to retort cinnabar concentrate, and a roast-leaching microwave treatment of chalcopyrite ore are described.

Jan 1, 1987

By Richard E. Steffens

The underground portion of Duke Power Company's Bad Creek Pumped Storage Project in northwestern South Carolina consists of a powerhouse cavern (132 m. long, 23 m. wide, 50 m. high), 407 meters of shafts and approximately 3615 meters of tunnel, both lined and unlined, with diameters varying from 4.2 meters to 9.0 meters. A case history is presented, including the early pilot tunnel exploratory work and how this affected design, the design of the project, and the excavation, rock support and tunnel lining work. Problems and experiences encountered during the construction are given. The effects of high horizontal insitu stresses in the granitic gneiss are discussed along with solution taken.

Jan 1, 1989

By R. J. Puchala, B. M. Hawrylewicz

High voltage electrical discharge in water causes instantaneous release of accumulated energy into water. The experiment described in this paper regards the utilization of the electric discharge phenomenon in rock splitting. The pressure in the shock waves created by the discharge inside a small volume of water enclosed in solid rock causes stresses which can result in breakage of rock. Holes drilled in tested samples were notched in order to weaken the tensile strength of the rock and achieve a uniformly directed split. The influence of the notches was theoretically analysed and compared with experimental data. Results of the tests have been statistically elaborated in order to correlate the newly-created surface to the energy supplied.

Jan 1, 1986

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time- dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct- shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that the risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2002

Load transfer capacity and failure mechanism of a fully grouted bolt installed across joints in shear is evaluated both experimentally and numerically in five types of bolts (low strength steel, rebar bolt and high strength steel). The strength of the concrete, bolt profile configuration, bolt mechanical properties and bolt pretension load play significant influence on the shear resistance, shear displacement and failure mechanism of the reinforced medium. Failure location moves towards the bolt joint intersection due to the increasing shear load, shear displacement and axial load developed along the bolt. Finally bolt failure occurs as a result of the induced axial and shear stresses acting between hinge points on either sides of the shear joint plane.

Jan 1, 2006

By Rod A. Levander, Kenneth B. King

INTRODUCTION The Panna Maria Uranium Project is located in South Texas, between San Antonio and Corpus Cristi, approximately 10 kilometers (6 miles) north of Karnes City, Texas. The tailings disposal facilities are located immediately south of the mill area and the central portion of the west pit. The mine and mill drainage pond is located north of the tailings pond. Location of the facilities is shown in Figure 1. The tailings pond is a disposal area for mill process wastes and has a capacity for storage of approximately 9 million metric tons (10 million tons) of tailings. This capacity is adequate for approximately 10 years of milling at a maximum rate of 2,700 metric tons (3,000 tons) per day. The tailings disposal facilities were designed to essentially eliminate discharge of contaminated waters to preclude degradation of surface streams or ground water. Water levels in the ponds will be maintained. through reuse in the mill and by evaporation. WASTE CHARACTERISTICS The sources of waste that is stored in the tailings pond include runoff from the mill area and tailings from the mill processing. The tailings consist of a sand slime slurry; the percentage passing the No. 200 sieve varies depending on the ore material, and it is generally in the range of 10 to 25 percent. The tailings have a density of approximately 1.2 metric tons per cu m (75 lb per cu ft) and an average specific gravity of 2.55. The liquid effluent from the mill consists of waste solutions from the grinding, leaching, extraction, and washing circuits of the mill. These solutions have an initial pH of 1.5 to 2.0 and contain the remnants of the leaching agents used in the mill process, sulfates, some silica as the primary dissolved solid, and trace quantities of soluble metals. This liquid is discharged with the solids into the tailings pond and is diluted by rainfall and runoff from the tailings dam. Runoff from the mill area, drainage from the mine area, and de-oiled water from truck washing facilities is discharged into the mine and mill drainage pond. Runoff from the mill area drains approximately 28 hectares (70 acres) from offices, shops, the mill site, the ore pad, haul roads, and adjacent areas. Mine drainage is collected in the mine area and pumped to the mine and mill drainage pond.

Jan 1, 1980

By Robert Klug, Nils Engelke

"In order to extract proportionately small quantities of valuable minerals, mining companies move large amounts of earth. A resulting waste product of this process has traditionally been stored in a semi-liquid phase known as tailings, typically stored in a large pond created by an earthen dam at the low end of a drainage basin. It is generally expected that these dams are stable enough to withstand the pressure of the stored material. Unfortunately, history shows us that this is not always the case. The Baia Mare dam in Romania failed in 2000, causing tragic and prolonged environmental damage to several major European rivers. The Bento Rodrigues dam in Brazil failed on Nov. 5, 2015, and that event resulted in the loss of 16 lives.In hard rock mining, many minerals are imbedded within the ore. As part of the mining process, valuable minerals are extracted from the ore; often, the mineral content is only a fraction of the total ore volume processed. To extract the minerals, the ore is typically crushed and pulverized into very fine particles, then wetted to form slurries. The minerals are extracted from the slurries through a series of flotation and/or sedimentation steps with the aid of water-soluble separation chemicals typically known as reagents. Following the mineral extraction, the resulting residual wetted ore cuttings are labeled as tailings. At the end of the extraction process, the tailings are in a thick semi-fluid sludge state, often with trace elements of the extraction reagents.Historically, these tailings are deposited in giant basins or sludge ponds, where they pose a great threat to the environment while binding large volumes of waste process water.Process water recovery and achievingdry tailingsCurrent generation engineering studies, trials and successful field implementation have shown that an alternate process known as dry stacking is practical. The dry stacking process deposits dewatered tailings into containment areas that are smaller in overall footprint and significantly safer by reducing the transfer of reagents into the tailings storage area. In addition to achieving the dry tailing benefits mentioned, it is possible to recover valuable process water while dewatering the tailings sludge utilizing modern separation technology."

Jan 4, 2018

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. DPM exposure is therefore regulated by the U.S. Mine Safety and Health Administration (MSHA). The current monitoring process takes days or weeks for exposure levels to be known, and a real-time monitoring device is needed. It is believed that infrared spectroscopy has potential for use in a real-time, field-portable device. This paper presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. 

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

During dusk, nighttime and dawn operations, effective illumination is a crucial component of safety for getting on/off mobile surface mining equipment and for preshift inspections. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers examined whether illuminance levels could be improved for ingress/egress systems and preshift walkaround inspections of equipment using light-emitting diode (LED) area luminaires. Illumination and glare were key metrics evaluated. Although headlamps provided adequate illumination, LED area luminaires illuminated a much broader area compared to the narrow spot lighting of the headlamp. Hence, the use of additional area luminaires can increase slip-trip-fall (STF) hazard awareness and detection. Furthermore, a commercially available luminaire demonstrated better results than a custom LED luminaire relative to discomfort and disability glare.

By J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit-optimization stages of a mining project. This paper presents an approach for optimizing final pit limits concurrently over all realizations in a stochastic model and using a risk-management framework to manage the geologic and economic uncertainty. A heuristic pit optimizer is used to find multiple uncertainty-rated pit shells. These uncertainty-rated pit shells follow the mean-variance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk-management framework to further eliminate suboptimal solutions along the efficient frontier. This results in a smaller set of final pit shells that can be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits, and two regions are targeted as potential regions for further exploration.

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production, but the thermal state of pellets in the drying section is still unclear. In this study, the temperature distribution of the drying section was investigated using computational fluid dynamics (CFD). The results indicate there is a coupling effect in the drying section of a traveling grate. Gas with higher temperature in down-draught drying (DDD) transfers heat to the up-draught drying (UDD) through the gap of the insulation board, and the temperature gradient of the pellet bed changes before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD are displayed in UDD in advance. To verify the model, a contrast experiment was conducted.

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By E. J. Wasp

An upsurge of interest in slurry pipelines to move coal from Wyoming, Montana, and Colorado to markets in the southwest, west, midwest and northwest has recently developed. Specific pipelines have been proposed to serve these markets; the routes of these lines are depicted in Exhibit I. It is, therefore, timely to discuss some technical aspects of the terminal facilities for these western coal pipelines. The discussion will be based on experience with the Ohio and Black Mesa pipelines as well as detailed planning and testing for a proposed 1,000-mile system from Wyoming to the middle south area. The economics of the pipeline terminal processes are heavily depend¬ent on site, type of process used, and other specifics of the situation. However, the following approximate breakdown of costs for a 1,000 mile, large capacity pipeline will be useful for orientation purposes. [Water supply 4 Coal cleaning 5 Feed preparation 10 Slurry transportation 72 Dewatering terminal 9 100%]

Jan 1, 1976

By J. H. Field

The sulfur dioxide emitted in low concentrations in flue gases from the combustion of sulfur-containing coals and fuel oils is a significant factor in contamination of the atmosphere with sulfur dioxide. A review of methods for treating gases containing high concentrations of sulfur dioxide shows that they are seldom satisfactory for purifying flue gases. Processes developed specifically for treating flue gases using liquid absorbents are costly and may cause localized pollution, because the cooled flue gases can settle in the vicinity of the stack. Bench-scale research is being conducted to investigate the use of dry absorbents for sulfur dioxide removal at temperature levels of about 250°- 300° F. and 600°-650° F. Alkalized alumina has been found effective for treating simulated flue gas and Is regenerable by hydrogen, carbon monoxide, or producer gas. Other metallic oxides have been tested as absorbents also. Chemically impregnated activated carbons removed sulfur dioxide from the gas at 265° F. Vanadium pentoxide is effective as a catalyst for oxidizing of sulfur dioxide in the simulated flue gas at temperatures lower than have been used commercially for gases with higher concentrations of sulfur dioxide. Conversions of sulfur dioxide to trioxide wore studied as a function of temp- erature over a range of about 570° to 750° F.

Jan 1, 1959

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By George C. Trevorrow

It is a pleasure to appear on this program and discuss a subject which is of particular interest to me. In my regular duties as Safety Director of Bituminous Coal Operators' Association, I am called on by member companies to discuss matters affecting face ventilation. As a member of the Joint Industry Safety Committee, as I will later describe, I have a part in processing requests for the use of auxiliary fans for face ventilation. The use of auxiliary fans in bituminous coal mines for this purpose came into rather wide use in the late. '20's when conveyor mining was introduced. In this application, the equipment consisted of a chain conveyor with a face chain conveyor parallel to the face on which the coal was loaded by hand and, in turn, was discharged onto the room conveyor and thence to a loading point on the entry at the mouth of the room. Another method was to use a shaker conveyor with a duckbill which was maneuvered across the face of the room from which the coal was loaded and transported by the shaker to the loading point. In either case the equipment did not readily lend itself to driving crosscuts or breakthroughs with the result that rooms were driven to depths of 250 or 300 feet without adequate means of ventilating the face area with the main split of air. It was, therefore, necessary to use other means of ventilating this area as the rooms were being driven and during retreat work if pillars were extracted. Auxiliary fans of the blowing type were utilized for this purpose. They were of very small capacity using small diameter tubing. By the time the room was driven half way to its projected limit ventilation was very poor or practically nonexistent. To compound the problem the fan was usually set up at the mouth or neck of the room and in many cases the intake air to the fan was the return air from the room. It is small wonder, therefore, that there is on record 12 cases where auxiliary fans were given as the cause of explosions. In 9 of these occurrences, arcs or sparks from open-type motors or accessory equipment on these fans were given as the primary ignition source. They fell into such ill repute that in a number of cases they were blamed as the ignition source even though smoking was strongly suspected as the primary cause.

Jan 1, 1967

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska's mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By Dietrich F. C. Hudewentz, Alfred H. F. Lücker

For centuries tunnellers have made use of the experience of miners. In West German coalmining tunnellers have returned the impulses in recent years by giving the miners valuable stimuli with the result that a technology has evolved which benefits drill and blast heading, opens the door to TBM heading and has developed special measures for difficult strata conditions in deep coal mines. WHAT DO THESE ROCK HEADINGS LOOK LIKE? The main roadways dealt with in this paper have crosssections of 20 to 40 m2, big enough to allow the massive airflows needed to aircondition the mines. Because of the difficult strata conditions they have to be supported: in shotfired headings mainly with multi-element arches, in TBM headings with rings of 6 to 6.5 m diameter. In West German coalmining the majority of rock headings are blasted. The proportion of rock headings driven by TBM was 11 % in 1980 and 16 % in 1981, a rising trend expected to continue. Drill and blast headings Drill and blast headings are normally equipped with two or three-boom electro-hydraulic jumbos, electro-hydraulic crawler-mounted loaders with 1.2 m3 shovel capacity, a movable working platform and both chain and belt conveyors for dirt clearance to the minecar loading point. Fans and air-condition plant complete the equipment. Spacing between arches is usually 0.8 m. Investment for this type of mechanisation works out at around 1.3 m DM.

Jan 1, 1983

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986