Search Documents

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By David M. Abbott

This paper is a companion to, and amplification of, the ?History? section of the 2014 version of the SME Guide for Reporting Exploration Results, Mineral Resources, and Mineral Reserves (SME Guide). The need for the careful examination and evaluation of mineral deposits has long been recognized. In the book De Re Metallica, Georgius Agricola noted, ?Moreover, a prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him? (1556, p.29). Agricola further stated, ?Now a miner, before he begins to mine the veins, must consider seven things, namely: the situation, the conditions, the water, the roads, the climate, the right of ownership and the neighbors? (1556, p. 30). The elements of Agricola?s seven things, much expanded, are incorporated into the 2014 SME Guide. As reflected in this quotation, veins were the primary concern of mining until 20th century technology permitted bulk mining techniques. The need for standardization of reserve descriptions arose along with the development of western mining in the United States and the concurrent development of mining engineering and mining geology as professions. By the turn of the century, debate about terminology of various classes of reserves was in full swing. Herbert Hoover noted in 1909 (p. 16-17), ?The old terms ?ore in sight? and ?profit in sight? have been of late years subject to much malediction on the part of engineers because these expressions have been so badly abused by the charlatans of mining in attempts to cover the flights of their imaginations. A large part of Volume I of the Institution of Mining and Metallurgy has been devoted to heaping infamy on these terms, yet not only have they preserved their places in professional nomenclature, but nothing has been found to supersede them. ?Some general term is required in daily practice to cover the available field of visible ore, and if the phrase ?ore in sight? be defined, it will be easier to teach the layman its proper use than to abolish it. In fact, substitutes are becoming as badly abused as the originals ever were. All convincing expressions will be misused by somebody.? Hoover (1909) noted that the common terms at the time were: ? Positive ore or ore developed: Ore exposed on four sides in blocks of a prescribed size. ? Ore blocked out: Ore exposed on three sides within a reasonable distance of each other. ? Probable ore or ore developing: Ore exposed on two sides, ? Possible ore or ore expectant: Ore in whole or in part below or beyond the range of vision. Hoover stated that these, and similar terms, overlapped and had the difficulty of failing to account properly for geologic variation in metal distribution beyond the exposed face. Certainly assuming extension of values along a vein is reasonable, but how far? Also, these definitions are for vein deposits, not all types of deposits are in veins. Hoover (1909, p. 19), therefore, defined the following terms. ? Proved ore: Ore where there is practically no risk in failure of continuity. ? Probable ore: Ore where there is some risk, yet warrantable justification for assumption of continuity. ? Prospective ore: Ore that cannot be included in the above classes, nor definitely known or stated in any terms of tonnage.

Feb 1, 2014

By Alan J. Solomon

The function of advertising is communication. Viewing the advertisements of mineral suppliers exposes the reader to a broad spectrum of purposes: announcements of new products, availability and supply, departmental services, company image, etc. It is the advertiser's hope that the message being conveyed is the same message being perceived by the viewer. To maximize this probability, the advertiser at least must carefully construct precise copy, identify the target audience and select the appropriate advertising medium. A truly successful and efficient ad, however, also must accurately reflect a product's life cycle, i.e., the rise and fall in demand for a product. Buggy whips and radio tubes are classic examples of items formerly in high demand. Industrial minerals are similarly affected by occurrences of product life cycles.

Jan 1, 1983

One of the core tenets of Sustainable Development is transparency and information sharing, i.e., government and corporate reporting. Governments report on issues within their sphere of responsibility to the degree that their constituents demand that they do so. Firms undertake reporting for two reasons: they are required to do so by law, and doing so makes good business sense. In recent years, stakeholders have come to see themselves as having a right to information about government actions and business operations that have the potential to affect their lives, health, community and environment. As a result, disparate groups, including industry associations, non-profit groups, academics, and individual firms, attempted to lay out what governments and firms should report. There are many types of sustainability reporting. In this paper we focus on three of them that both governments and firms utilize. We discuss the benefits of each. We argue that while the goal of complete and perfect data is not achievable or feasible, sustainability reporting of all three types is necessary to ensure that sound public and private decisions are made.

Jan 1, 2007

By J. E. Castle

The essential foundation upon which to build an effective marketing program in industrial minerals is the ability to produce competitively mineral products meeting precise customer specifications and to ship them promptly and on schedule. Without this prerequisite, all the other factors in a second marketing program-creative sales management, energetic solicitation, advertising, technical service, new products, etc.are without meaning. The primary image to be created in the mind of customers is that of the reliable and prompt supplier of mineral products at competitive prices and of standard, uniform quality. With this favorable image implanted, it becomes possible to integrate the other essential factors into a strong marketing program; and without this image, little can be accomplished. After having .made provision for the basic product ion position outlined, there are then two fundamental considerations in the design of a successful marketing program for industrial minerals. The first of these is that the number of potential customers for the typical industrial mineral product is, relatively small, and indeed compared to the number of customers for consumer products, the number is actually minute. The second consideration is that the customers for industrial minerals are manufacturers and producers rather than consumers. These two factors lead to a necessity that the marketing program be specifically and uniquely tailored to fit the individual mineral product to be sold and to conform to an existing pattern of distribution.

Jan 1, 1962

By B. K. McMahon

Block caving is an efficient mass-production method for the underground mining of large orebodies. However, the block-caving method requires a substantial investment in developmental works, based on the assumption that the rock will cave. Efficient block caving is prevented if the rock forms stable arches or breaks into fragments that are too large to pass easily through the finger raises. Under these conditions, the cost of the additional labor, drilling, and blasting required to assist caving may be sufficient to make marginal orebodies uneconomic or alternative mining methods more attractive. Reliable methods for the prediction of the block-caving behavior of an orebody are clearly needed at the initial planning stage. These methods should be capable of considering both geological and engineering aspects of a block cave, as experience has shown that the manner in which a block cave is initiated and developed may be almost as important as the geological conditions such as the nature of the rock material, degree of alteration, characteristics of the joints and faults, etc. The initial state of stress in the rock mass should also be considered.

Jan 1, 1969

By Sam Lo Grasso, Carlos Herranz Calvo, Stuart Warren, Ted Giesing, Charles Marchesano

Mott MacDonald and Project Management Advisors are providing Technical and Project Management services for San Diego County for the Courthouse Commons Project. The Courthouse Commons Project involves the redevelopment of three downtown blocks owned by San Diego County and construction of an Inmate Transfer Tunnel between the County Central Jail and the San Diego Central Court. The tunnel will be 327 feet long, crosses the San Diego Fault and is being constructed using the Sequential Excavation Method (SEM). This paper discusses the history and procure‑ ment strategy for the project, the technical aspects of the transfer tunnel and the con‑ struction progress of the tunnel to date.

Jun 13, 2021

By B. Campbell

This paper will detail the successful construction methods of a 20- foot diameter wet well shaft, approximately 180 feet deep in overall depth and 150-feet below the water table, adjacent to Lake Nacimiento, in San Luis Obispo County, California. In addition to this, highlights will include the selection process in determining the most economical support of excavation, while minimizing risk of large water inflows as indicated in the Owner?s Geotechnical Baseline Report (GBR).

Jan 1, 2010

By G. M. Ellis

This paper deals with some aspects of concrete construction in remote locations and/or cold climates. The writer's experience covers 25 years in construction in western and Central Canada. I will bring forth some pertinent observations and cost facts learned from this experience. Let us start by saying that there is nothing more important than preplanning the entire project. By this I mean the production of the engineering design, working drawings, soliciting of prices and ordering of all equipment and contractors work, the delivery of all equipment and all onsite work. All of this should be placed on a master schedule, preferably a C.P.M. We have been using C.P M. Scheduling for all of our work for 5 years and have found it in-valuable. This preliminary schedule will show initial items of work and target dates. After main equipment orders are placed and deliveries confirmed, the construction schedule can be revised to include manpower and construction equipment requirements. From this information the size of camp is determined. This, of course, must be ordered several months ahead. The manpower schedule can be broken into trades to tell us the number of men of each trade required at any time. This is important in helping to determine where the men must come from and whether or not any incentive is needed to get them. The schedule will also point out if it is impossible to get the project closed in before winter becomes too severe unless overtime is worked or the project is started in early spring. In most parts of Canada cold weather starts in October and lasts through April. A common term of reference has been to wait for the frost to come out of the ground before starting work in the spring. In some areas this can be as late as June. The construct-

Jan 1, 1971

By E. Wm. Heinrich

Glass sands fall into that extremely select category of mineral deposits that requires a fantastic degree of natural concentration (95% +) of a single component before they can even be considered as ores suitable for further refinement. The combination of geological factors that has produced such an environment of "mineralogical single-mindedness" has appeared only rarely. Factors that require consideration in the economic evaluation of a potential glass-sand deposit can be grouped into three categories: 1) geological (e.g., size, shape, structure); 2) petrographic (e.g., grain size, accessory minerals, nature of iron contaminants); 3) geographic - political (e.g., proximity to consumer, size of market, zoning restrictions). Of particular con ern is the nature of the iron contamination. Iron-bearing species appear as 1) accessory mineral grains, either detrital or authigenic, 2) cements, 3) grain coatings, and 4) quartz-grain inclusions. Selection of the cheapest form of beneficiation requires precise information on the mineralogy of the iron species and their detailed petrography. Because of the antipathetic relationships, in many parts of the United States and Canada between the geographical locations of glass plants and the geological distribution of glass sands, the selection of ac suitable source for a particular glass plant may be dichotomous. One may seek either an exceedingly pure "classic" type glass sand that is relatively distant and whose cost includes a major transportation charge or a relatively proximate and somewhat "impure" source whose cost includes a substantial fee for beneficiation.

Jan 1, 1974

By John S. Anderson

The need for fuels and minerals in this country is estimated to double, triple, or even quadruple by the end of the present century. Even assuming more recycling of scrap metals and some priority allocation of energy, as has been done, for instance in war time, the projected increase in the nation's population and ever-increasing wants of that population will require vastly more minerals than are now being produced. Since mineral ores are being mined at lower grades, and since all minerals, including fuels, are having to be mined from deeper deposits, the amount of surface land to be disturbed will, inevitably, be increased. We cannot depend on foreign sources to supply all the extra requirements, since the non-U.S. population is increasing, in most cases, faster than our own. Furthermore, starting from a lower base, their mineral needs may accelerate more rapidly than ours. Restrictions on exports may be applied in foreign countries, if it appears that remaining reserves are not sufficient to fill the national needs. In vice; of the opposition which the mineral industry is receiving, as has been well described at these sessions and elsewhere, what can we, as mineral producers, anticipate as regards our ability to continue to operate, to sway nothing of expanding production? Although not minimizing the problems involved, it seems obvious that, except under emergency conditions, the country cannot tolerate a reduction in the available

Jan 1, 1971

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By Hou Xilun

Three production methods of rapid cold bonding and low temperature bonding pellets using sponge iron powder as a binder have been successfully developed. These methods differ from ordinary bonding method by no addition of salt and other catalyzers, no corrosion of equipment and no pollution of environment. Mechanism of pellet bonding is studied. Experiment shows that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the production of metallic pellets continuous and stable. These methods are substituted for traditional high temperature firing of oxidized pellets in direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved. Production cost may also be decreased. The production of cold bonding pellets does not need additional area.

Jan 1, 1980

The Longwall Strata Control and Maintenance System (LoSCoMS) is designed to monitor shield pressures in real-time from longwall faces and to provide on-line information related to underground strata behavior and longwall mining operation. The information includes shield pressure data with statistical analysis of setting, developing and final pressures, prediction of shield pressures for the following shift or day, etc. and maintenance data on the shields. The LoSCoMS has been installed and tested at Shoal Creek Mine operated by Drummond Company, Inc. The system is providing valuable information to mine operators for better understanding of underground behaviors. As a result, it has become an effective tool for minimizing ground control hazards and reducing out of seam material.

Jan 1, 1997

By John E. Edkins

Metal sulfides, chiefly pyrite and mFnor sphalerlte zssociated with che Herrin (No. 6) coal member of the Pennsylvania Carbondale Formation, have been concentrated in a coal refuse deposit in southern Illinois. Oxidation of pyrite has produced highly acid waters with high concentrations of iron, zinc (up to 200 parts per million) and toxic trace elements that have leached downward to a water system perched on glacial drift. Chemical, petrographic, low-temperature ashing and x-ray diffraction were performed on cores. The data show that economic recovery of zinc and other trace metals is unlikely at this site. Energy (coal) recovery at the Superior Washer site is possible if resultant environmental problems are considered in the planning.

Jan 1, 1981

By W. W. Wen

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an mine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electrokinetic behavior of coals of different rank and degree of oxidation were studied by an electrophoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite was depressed. Comparing the flotation results with the electrokinetic results verified that in the presence of ferrous sulfate, the maximum hydrophobicity of oxidized coal with dodecylamine and frother is near its IEP which is around pH 6.5 to 7.0.

Jan 1, 1976

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987