Search Documents

By V. E. Chrapunov, T. V. Chnyrenkova, R. A. Isakova, V. A. Luganov

Arsenic-gold bearing ores are used as a flux in smelting or leached out to extract gold. To decrease arsenic content in processed materials and to break up the lattice to free the gold, raw materials are roasted. This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. The process allows to minimize the negative influence on the environment but requires costly engineering solutions. Roasting in a neutral medium or with limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in the autogeneous mode in fluid bed furnaces. If oxidizing roasting of the concentrates is done in the presence of soda, practically all arsenic and sulfur form water-soluble compounds and remain in cinder.

Jan 1, 2002

By David Yankovich, Geoff Hughes, David Haug, Jon Kaneshiro

"In March 2013, the Sanitation Districts of Los Angeles County began final design of the Joint Water Pollution Control Plant (JWPCP) Effluent Outfall Tunnel project. The new, approximately 7-mile, 18-ft internal diameter tunnel will provide additional capacity and redundancy for the existing 8- and 12-foot diameter tunnels, which were built in 1937 and 1958, respectively. Connections to an existing, active 14-foot arch force main and four existing ocean outfalls ranging from 5- to 10-foot diameter are required. This paper will present geological features for the project, and details of the proposed post-tensioned tunnel liner and associated structures. INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) are 23 independent special districts serving approximately 5.3 million residents in Los Angeles County. Seventeen of the districts that furnish sewerage services to the metropolitan Los Angeles area are signatory to a Joint Outfall Agreement that provides for a regional, interconnected system of facilities known as the Joint Outfall System (JOS). The JOS service area is shown in Figure 1. The JOS serves an area that encompasses 73 cities as well as unincorporated territory and parts of the City of Los Angeles. The JOS provides wastewater collection, treatment, reuse, and disposal for residential, commercial, and industrial users, and it includes seven treatment plants, the largest of which is the JWPCP, located in the City of Carson. Currently, secondary treated effluent is conveyed through two 6-mile long parallel tunnels, 8- and 12-feet in diameter, from the JWPCP to a manifold structure located at Royal Palms Beach, near White Point on the Palos Verdes (PV) Peninsula, from which four seafloor outfalls extend offshore. The two main outfalls, 90- and 120-inches in diameter, extend approximately 1.5 miles offshore and discharge at a depth of approximately 200 feet below sea level. The other two outfalls, 60- and 72-inches in diameter, are used for additional capacity during heavy rain events and extend a shorter distance offshore and discharge at shallower depths. A schematic of the existing system with the proposed tunnel and structures is shown in Figure 2, and the proposed 18-ft diameter tunnel alignment is shown in Figure 3. Both existing tunnels and main outfalls are required to be in service at all times."

Jan 1, 2016

By W. J. Douglas

The mine manager in today's environment is faced with a wide variety of problems and challenges which must be addressed if efficient and profitable operations are to be achieved. Expansion of operations has, in many instances, resulted in inexperienced work crews, face supervisors, and superintendents. The complexities of a mining system preclude rapid movement through the learning curve for moat personnel. The management of production suffers both from this inexperience and the lack of standard procedures and methods for planning, schedul ing and analyzing production systems. The lack of visibility of information, as well as of the operations themselves, due to their remoteness, adds to the problem of production management.

Jan 1, 1980

By E. M. Abraham

The establishment and survival of different grass species and cultivars on various phytotechnic treatments at a limestone quarry was studied. The treatments applied were: a) bare soil, b) bentonite, c) bentonite-straw and d) asphalt-straw. According to the results, significant differences were found among species and cultivars, growing on different treatments as far as plant growth and survival are concerned. The seed germination was higher on bentonite -straw and asphaltic-straw than on bentonite but the plants survival were higher on bentonite. Lolium perenne had higher seed germination rate and better establishment than the other tested species at all treatments. However, the survival rate of Agropyron desertorum and of the cultivars palestina and chrysopigi of Dactylis glomerata was higher than of the other species.

Jan 1, 2007

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By V. Rajagopal

Corrosion and abrasion properties of a series of chromium-containing cast iron balls with Cr contents ranging from 0 to 29% was evaluated and compared with austenitic stainless steel and mild steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite with either 5% pyrrhotite or 5% chalcopyrite under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynamic polarization curves under abrasion. An offset in their electrochemical activities was observed somewhere between 16 and 26% Cr. In fact, 26 and 29% Cr cast irons showed an excellent corrosion resistance approaching that of austenitic stainless steel. Flotation recoveries were estimated on a 95% quartzite + 5% pyrrhotite sample ground with various cast iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with corrosive wear obtained from marked ball wear test and with flotation results.

Jan 1, 1991

By Bart Bartholomew, Randall J. Essex

INTRODUCTION In June of 2004, at the North American Tunneling Conference in Atlanta, an all-day workshop was conducted to review the application of Geotechnical Baseline Reports (GBRs) for underground construction. The moderator for the program was Bart Bartholomew, former President of Fruin Colnon Construction Company. The program involved commentary by a panel of engineers, owners, contractors, and legal representatives within the North American tunneling industry, as well as an extended audience discussion. The panelists were: Peter Douglass, President, Peter Douglass, Inc. Randall Essex, Executive Vice President, Hatch Mott MacDonald Joseph Gildner, Deputy Director for Technical Services, Sound Transit Randall Hafer, Esq., Kilpatrick Stockton Robert Fitzgerald Esq., Watt, Tieder, Hoffer, & Fitzgerald Kirk Samuelson, Senior Vice President, Kiewit Construction Group DEVELOPMENT OF PROGRAM FORMAT The focus of the program was to assess the state of the practice in the preparation of GBRs, and to discuss improvements that could and should be made with regard to their preparation, interpretation, and application. The approach used to achieve this focus in the broadest possible way was unique, in that it involved the panelists’ preparation of the workshop format and materials months before the presentation of the workshop. First, each of the six panelists was selected by the moderator based on their reputation and involvement in their respective fields of expertise, taking care to maintain balance and contrast within the collective pool of talent assembled. Following selection and agreement to serve on the panel, each panelist was asked to independently submit to the moderator a list of the six most pressing issues involving GBRs that they each frequently encountered in their individual professional experience. Each was asked to rank their issues in descending order of perceived importance. This process resulting in a pool of thirty-six potential or “candidate” issues for use in the workshop program. Contrary to the moderator’s expectations, there was surprisingly little duplication among the thirty-six issues submitted.

Jan 1, 2005

By D. C. Hogeman

Growing Greener is the single largest investment of state funds in Pennsylvania’s history, allocated to address the Commonwealth’s critical environmental concerns. Signed into law by Governor Tom Ridge on December 15, 1999, Growing Greener will enable the Department of Environmental Protection (DEP) to appropriate nearly $240 million over five years, to watershed restoration and protection, abandoned mine reclamation, and oil and gas well plugging projects. DEP has utilized these allocations in some remarkably innovative ways, as it: involves the cooperation of several state agencies, local governments, and grassroots organizations to address environmental concerns of the Commonwealth, provides funds directly to watershed groups based on locally determined decisions for local watersheds and offers a user friendly process. In three years, over $130 million in watershed restoration and improvement projects have been initiated.

Jan 1, 2002

By Osvaldo A. Bascur

Intelligent systems (IS) technologies have received much attention in a wide range of process engineering applications including process operations. With the revolutionary progress in information and computer technologies applying the latest technologies in metallurgical complexes has become a serious challenge to both management and technical teams. Objects and components are changing the way everyone relates to their computer and networks. Goals of real time performance monitoring includes maximizing the profitability by maximizing production, improving efficiency, attending product quality, costs, maintenance, environmental and safety regulations. Designers must consider the greatly expanded desktop computing, Microsoft object technology, Internet and how to build these systems. This paper discusses some opportunities and challenges using objects, components in designing applications and integrating intelligent systems tools. Two examples using performance equations and IS technologies applied to mineral processing are presented.

Jan 1, 1997

By Michael A. Trevits

A mine fire represents one of the most dangerous and challenging safety issues facing underground mine operators. Given the right circumstances, a mine fire can occur at any location in the active or abandoned mine workings, can quickly grow beyond control, and threaten the welfare and livelihood of the entire underground workforce. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), has been conducting an in-depth program of research addressing mine fire prevention, early and reliable fire detection, and mine fire suppression technologies. One portion of this program is focused on understanding the characteristics of mine fire combustion products and flame spread through large scale deep-seated (firmly established) fire tests and use of computational fluid dynamics (CFD) modeling. In this study, two deep-seated fire tests were conducted; one fire consisted of coal material and the other utilized the two most abundant fuel sources found in a coal mine: coal and wooden cribbing blocks. The fires were burned to completion while the combustion products were collected and analyzed. In addition, an array of thermocouples was placed within the body of the material to measure flame spread rate. The coal fire test information was then used to develop a CFD model of the fire. This paper describes the fire tests, provides insight into characteristics of flame spread, and presents the CFD modeling work results.

Jan 1, 2009

By D. Oyler

The National Institute for Occupational Safety and Health’s(NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tail-gate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

Jan 1, 2004

By Igor Gonzales G.

The Southern Peru Copper Corp. (SPCC) recently built an integrated copper project consisting of dump- and heap-leaching operations at its mine complex in Peru. The pregnant leach solution (PLS) containing the solubilized copper from the leaching operations is processed in a new solvent extraction/electrowinning (SX/EW) facility to produce high-purity cathode copper. The dump leaching and SX/EW facilities are located near the Toquepala mine site. The crushing and heap-leaching operation is located at the Cuajone Mine. The pregnant leach solution from Toquepala and Cuajone is pumped 35 km (22 miles) to the SX/EW plant at Toquepala. The SX/EW plant consists of three trains of solvent extraction (SX), a tank farm area and an electrowinning (EW) facility. The solvent extraction plant has a total PLS flow capacity of 3,210 m3/hr (113,360 cu ft/hr). The electrowinning facility has an expected long-term production capacity of 97 t/d(107 stpd) or about 35 kt/a (38,500 stpy) of cathode copper. However, present production exceeds the expected long-term by about 20%.

Jan 1, 1996

By Todd Kilduff, Ryan O’Connell

Pipe canopies continue to gain momentum as a reliable methodology for construction of excavations below critical facilities with minimal surface settlement tolerances, such as railroads or roadways. Two tunnel projects designed by Kilduff Underground Engineering in the Salt Lake City, UT area, each at varying stages of completion, had project design criteria for selection of a tunneling methodology to minimize surface settlement. Both projects consist of a pedestrian tunnel, one crossing beneath a major roadway in downtown Salt Lake City and the second beneath UPRR tracks. Both projects were in difficult, coarse alluvium/fan ground conditions with project criteria that resulted in minimal cover above the tunnel. For each project, a pre-support pipe canopy was designed, requiring the placement of steel, canopy pipes driven the extent of the tunnel length. The pipe canopy is installed using a trenchless technology and then excavated with SEM tunneling and shoring provided by traditional support of excavation methods. The pipe canopy pre-support method offers a low-impact method to install an underpass beneath critical structures by adding significant stiffness to the subgrade to mitigate surface settlement during the main tunnel excavation sequence. These case studies seek to communicate the challenges associated with pipe canopy installation in site-specific ground conditions and explains how these challenges were overcome. This paper aims to define the project risks and describes the pipe canopy methodology as a viable solution to mitigate surface settlement in low cover tunneling scenarios.

Jun 13, 2023

By Verya Nasria, William Bent, William Hogan

"The South Hartford Conveyance and Storage Tunnel (SHCST) project is a significant component of the Hartford Metropolitan District’s (MDC) long-term control plan (LTCP), which is overseen by the Connecticut Department of Energy and Environmental Protection (CTDEEP). This project will address a portion of the MDC’s Clean Water Project (CWP), which will reduce combined sewer overflows (CSOs), eliminate sanitary sewer overflows (SSOs), and reduce nitrogen released into the Connecticut River. The purpose of the SHCST project is to eliminate West Hartford and Newington SSOs, eliminate Franklin area CSOs discharging to Wethersfield Cove and minimize CSO discharges to the South Branch Park River. The locations of each overflow are shown in Fig. 1. In 2010, the district prepared a preliminary design report (PDR) for the SHCST project, which included relief of the Folly Brook trunk sewer and proposed to keep the tunnel boring machine (TBM) retrieval shaft within the city limits of Hartford. Figure 1 shows the 2010 PDR recommended tunnel route. Subsequent to the PDR, the objectives of the SHCST have slightly shifted. In accordance with ongoing revisions to the LTCP, relief of the Folly Brook Trunk Sewer is no longer necessary. Additionally, the MDC has decided to perform less sewer separation in the Franklin Avenue drainage area. To replace the sewer separation, new relief points are proposed within the Franklin area and will be diverted to the SHCST. Figure 1 also shows the current recommended tunnel route (Alignment F). During 2012, the MDC conducted an evaluation of the potential of connecting the proposed North Tunnel (originally proposed as an independent tunnel with its own pump station) into the South Hartford Conveyance and Storage Tunnel. This evaluation concluded that the two proposed tunnels could reasonably be connected together and operated as a single tunnel system utilizing the tunnel pump station at the eastern terminus of the South Hartford Tunnel (Fig. 2). It also was concluded that this alternative was less costly than two independent tunnel systems."

Jan 1, 2014

By D. Burkhard, E. Herth

"Geologic structure and properties are the primary influences on ground control at San Juan Mine. Geotechnical properties of the coal seam and near seam strata, the presence of above seam sandstone paleochannels and water, are thought to be the leading contributors to ground control issues. It is the confluence of specific geologic conditions rather than isolated features that most often produce adverse conditions. Altering primary support installation and mining practices are done when unfavorable conditions appear during development. Installation of standing support is most often employed when adverse conditions develop at later dates. REGIONAL GEOLOGIC SETTING San Juan Mine is an underground coal mine located on the western flank of the San Juan Basin in northwest New Mexico. The San Juan Basin is contained within the south eastern region of the Colorado Plateau geographic province. The basin contains multiple coal bearing formations and is also a major producer of coalbed methane gas. San Juan Mine is stratigraphically located within the Fruitland Formation. From a prominent monocline marking the western boundary of the basin, the formation dips gently to the east towards the center of the basin. The primary driver for the deposition of coal bearing formations within the basin was the Cretaceous Inland Seaway. Multiple cycles of transgression and regression driven by sea level rise and tectonic subsidence deposited rock types from marine shale’s to terrestrial sandstones. The Sevier Mountains to the west of the seaway likely provided the sediment supply for the Fruitland Formation. During a major cycle of seaward regression, the Pictured Cliffs Sandstone Formation prograded over the marine Lewis Shale. The coal bearing Fruitland Formation followed, being deposited over the Pictured Cliffs. The Fruitland Formation contains numerous coal seams and is approximately 400 ft. thick at San Juan Mine. Fruitland Formation coal seams are numbered in order of superposition. San Juan mines the Fruitland number 8 seam. Dating has placed the age of the seam at approximately 73 to 75 million years [1]. LOCAL GEOLOGIC SETTING The Fruitland 8 coal seam dips approximately 1-3 degrees towards the E-NE. At San Juan Mine, the seam displays a mild plunging, synclinal structure, the axis roughly bisecting the mine from west to east. The number 8 seam consists of five coal benches and four volcanic ash band partings labeled sequentially based on superposition. The lowest portion of the seam is the 8-1 bench, the 8-2 through 8-5 benches following sequentially to the top of the minable seam. Ash band partings are labelled P1 through P4 from bottom to top respectively. The presence of distinctive partings and benches allows for seam definition and aids in identifying mining horizons."

Jan 1, 2016

By Aijuan Zhang, Liang Zhao, Yutao Wang, Yu Bao

In the green backfilling mining of underground coal mines, gangue in a coal seam is used to replace and fill goafs. However, the gas drainage time changes in the amount of gangue output and order in the extraction sequence of stope blocks, thereby changing the production output. A multi-objective integer programming model was proposed to solve this based on an improved non-dominated sorting genetic algorithm. The results show a feasible gangue filling rate can be found and the extraction sequence for a long-term planning time is optimized. It increases the planned annual output by 26% and reduces equipment idle time.

May 23, 2022

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By William O. Rasmussen

Exploration requires processing highly varying kinds and amounts of geologic information. Successful discovery dictates that this be done quickly with maximum confidence. Most phases of exploration are more or less applicable to computer reduction on a routine basis. The use of digital computers to reduce raw data into interpretable form, lets the exploration geophysicist concentrate on interpretation and presentation, and to consistently apply more sophisticated and comprehensive analytical techniques, not practical before. In applying these concepts for the past several years, various efficient programs have evolved which provide more complete evaluation of all data including the pro- vision for more unique solutions. This has resulted in greater refinement and ability to select the most advantageous drill sites in a minimum time at a minimum cost or, in rejecting as soon as possible a project on which additional effort is no longer justified. Practical examples of computer applications in magnetics (air and ground), induced polarization and resistivity are discussed.

Jan 1, 1969

By Scott L. Burrill

In the past 100 years in the mining industry, many references are made to the "Widow Makers", 'Miners Con" and many other derogatory names related to physical hazards. They reflect the lack of understanding of the problem facing the early day miner. Workers were enticed, in some cases, to take a chance against a medical question mark that could not be explained by the doctors of those early days. The optimism of the mining man and the challenge of work led him to believe that the physical results could not apply to himself and only applied to some of his fellow workers. Much of the time, to his dismay, he found that he had lost to the game of chance. As medical knowledge improved and mining management began to understand the effects of conditions in the mines and beneficiation plants, steps were taken to alleviate or eliminate the health hazards that were present, The organizations engaged in mining that did not take an active interest in employee health found themselves to eventually be placed in the position of being forced to take action by Federal and State legislation. We find ourselves in the 1970's on the threshold of a new era where the general public is concerned vociferously about "their" environment and the industry feels the governmental controls more strongly than ever before. It can be said that in the past 100 years we have advanced from the "Widow Makers" of the 1870's to the "Retirement Makers" of today. The difficulties of the early days in underground mining were of times compounded in the beneficiation plants above ground. As late as the 1950's some crushing and milling installations in the United States were operating under environmental conditions that complied to the then existing legislation but were below the health level sought by conscientious management. The Mission Concentrator Crushing Plant was designed in 1959 and placed in operation in July, 1961. In the past ten years the crushing plant has been continuously complimented by technical people, government inspectors and casual

Jan 1, 1971

By D. E. Walsh

With the exception of the development of large scale mining equipment (haul trucks, draglines, shovels, etc.), there are likely few other candidates responsible for the ability to exploit large tonnage, low grade deposits, than the development of large capacity comminution equipment and circuits; crushers and grinding mills. Ball mills are often the final step in the comminution process and are responsible for providing what should be the optimum particle size distribution of ore to subsequent mineral concentration steps in the flowsheet. Because comminution processes are such high cost centers for milling operations, both capital and operating costs, an enormous amount of research has been conducted to study and model their performance, in order to improve efficiencies (Kelsall, et al., 1969; Austin et al., 1984; Napier-Munn, et al., 1999; Powell and Smit, 2001). With respect to modeling ball mills, estimates of the breakage rates for individual size classes of ore particles are fundamental, as are the particle size class breakage functions (the progeny of particle sizes produced from breaking a coarser particle size class), also termed appearance functions. Fundamental research into particle breakage in tumbling mills focuses on how much energy is input into single particles versus how they break and what size distribution of particles results. Several test methods, including JKMRC?s well known dual pendulum test and drop weight test, have been developed for the breakage of coarse particles down to 6 mm in size (Napier-Munn, et al., 1999). Work on the breakage of finer particles is still an area of intense research and single particle breakage is being investigated as are multiple particle, fixed bed methods (Hoffler and Herbst, 1990; Bourgeois et al., 1992; Whiten, 2007).

Jan 1, 2011