Search Documents

By Earl L. Rau

At the present time, whether an electric utility uses high-sulfur coal is largely determined by geographical location, clean air legislation, and the age of the power plant. Acid rain legislation may well be the new force to change the use of high-sulfur coal. A number of coal papers were presented at the SME Fall Meeting in St. Louis, MO, Sept. 1986. These papers discussed high-sulfur coal in relation to its economics, trends and prospects, value of cleaned coal, and coal-cleaning technology. The Clean Air Act of 1970 required the reduction of SO, emissions from most stationary electric-generating plant to 0.5 kg (1.2 lbs) SO2, per million Btu of heat input. It was possible for many plants to utilize lower-sulfur coal or a mixture of high-sulfur and low-sulfur coal to meet this emission requirement. This 1970 act greatly increased the use of low-sulfur western coal. The 1978 amendment to the Clean Air Act required all new plants to use Flue Gas Desulfurization (FGD) to meet a requirement of 70% reduction of potential SO2 emissions to 0.3 kg (0.6 lb) SO2 per million Btu of heat input. With the requirement to use FGD, there was little or no demand for low-sulfur western coal in new eastern power plants. If' new acid rain legislation is enacted, it likely will require sizeable reductions in SO2, emissions by existing coal users. There might then be a shift to greater use of low-sulfur coals. The low-sulfur coals could come from either western or eastern mines or from cleaned eastern coals. Economics will dictate the approach older power plants will take to meet new regulationsuse FGD or low-sulfur coal. Coal use for electric power generation has changed from 1970 to 1985. Table 1, (Land, preprint 86-333) shows the change. The table shows that in 1985, US utilities used about 255 Mt (280 million st) of high-sulfur coal. Some 45 to 54 Mt (50 to 60 million st) of high-sulfur coal is being used in plants equipped with FGD and most of this use is in eastern states. This leaves 200 to 209 Mt/a (220 to 230 million st) of high-sulfur coal being used without FGD treatment. These plants are at risk if acid rain legislation is passed. Most of these plants are in the east and are more difficult to supply with low-sulfur coal. Estimates range from $20 to $30 billion capital investment and from $5 to $9 billion dollars per year operating costs to reduce SO2, emissions from those old medium-to-high-sulfur coal-burning plants. G. W. Land, (preprint 86-333), also presents tables relating to power generating costs and coal types. The author's tables are extracted from Land's tables IV and V. Table 2 here presents costs for a new plant. This includes the impact of different heat rates, fuel costs, fuel qualities, operating and maintenance costs, labor costs, and waste disposal costs. Table 3 compares estimated costs to retrofit an older plant with a limestone scrubber versus switching the same plant to low-sulfur eastern or western coal. Costs of switching include upgrading the electrostatic precipitator and - with western coal - costs of derating. Bhagwat, (preprint 86-325), details the trends in high-sulfur coal markets from 1974 to 1984. He also gives some prospects for high-sulfur coal markets, 1984 to 1994. The prospect depends mostly on whether acid rain legislation is enacted. By 1994, if New Source Performance Standards (NSPS) continue to be applied, high-sulfur coal demand from six mid-west and eastern states is expected to increase by 27 Mt (30 million st). • L. A. Khan and J. W. Baxter, (preprint 86-373), discuss several coal cleaning technologies such as froth flotation of fines, bulk oil separation and oil agglomeration, oil agglomeration/flotation, and air-floc flotation. ? (Space limitations preclude listing references. A complete list is available from the author.)

Jan 1, 1987

One of the challenges in the development of mineral processing simulators is the modelling of liberation characteristics of particles produced by comminution circuits. Understanding the mineral characteristics of these particles is one of the keys to predicting their behaviour in separation circuits. While more fundamental research seeks to model the non-random breakage of ores this work examines whether we can move forward now by using observed characteristics of ores to model the composition of particles generated in comminution processes. The current work examines a range of ores and identifies which of these exhibit the pattern of similarity of composition for particles in a given size class that has been produced as the result of a variety of breakage conditions. The impact of mineralogy and texture on the evolution of liberation characteristics for both valuable and gangue minerals is discussed.

Jan 1, 2009

By W. Randall, Robert M. Leary

Twin 1250 m (4100 ft.) long highway tunnels through Cumberland Mountain near Middlesboro, Kentucky are planned to be completed in the early 1990's. The tunnels will be excavated in sandstones, limestones, and shales, dipping at 35 to 50 degrees and striking nearly perpendicular to the tunnel alignment. In 1985-86 a pilot tunnel was excavated as a crown drift along the alignment of the southbound tunnel. The benefits of the pilot tunnel in reducing uncertainties for main tunnel construction are discussed. The cost-benefits of the pilot tunnel are examined in view of estimated main tunnel costs.

Jan 1, 1987

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process 1.2x0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm.

Jan 1, 2002

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006

By D. Anthony, R. A. Williams, R. Raponi

Barrick Gold Corporation in conjunction with SNC Lavalin Engineers and Constructors have developed basic engineering design for counter current decantation thickener (CCD) plants capable of processing 44 000 t/d. To achieve this throughput in a single train, the largest high-rate thickeners installed to date have been utilized in concert with large process slurry and solution transport systems. Process reliability and plant operability and maintainability have been carefully considered in order to develop a practical, yet cost effective design. The design also incorporates the challenges associated with installation of large equipment and structures in a remote location, with a climatically hostile environment, situated in a high seismic activity zone.

Jan 1, 2002

By R. Y. K. Yang, O. Olajide, E. H. Cho

"This study focuses on partial leaching of coal pyrite with sodium sulfite in order to increase its degree of liberation from the coal matrix, which might help to increase the removal of coal pyrite, together with trace elements of arsenic (As), selenium (Se) and mercury (Hg) by froth flotation. The U.S. Bureau of Mines’ two-stage reverse flotation process was applied to further reject coal pyrite in the second stage, where pyrite was floated while coal was depressed. The results show that the leached coal flotation with sodium sulfite produced lower pyritic sulfur content in the clean coal by approximately 25% compared to the flotation of unleached coal. The synergism mechanism between the leaching and the two-stage flotation is delineated. The rejection of trace elements (As, Hg and Se) after the two-stage flotation process with unleached coal followed approximately that of pyritic sulfur (64.6%). However, after the two-stage flotation with leached coal, the rejection of Se was as high as that of pyritic sulfur (77.9%), while the rejections of As and Hg were 20% lower than that of pyritic sulfur, or followed approximately the same rejections obtained through the two-stage flotation with unleached coal.IntroductionSO2 is a reducing reagent, but when it is combined with oxygen in an acidic solution, it will become a strong oxidizing reagent for leaching coal pyrite. Sundaram et al. (2001) found that the reagent could leach coal pyrite to produce ferric iron, which, in turn, catalyzed the oxidation of SO2. Similarly, Cho et al. (2009) found that the reagent could leach pyrite as well as mercury from coal. In the present study, coal was preconditioned by partially leaching coal pyrite in water-coal slurry with sodium sulfite at 48° C. The partial leaching of coal pyrite may enhance its degree of liberation from the coal matrix and give a chance to be rejected more effectively during the flotation.The two-stage U.S. Bureau of Mines’ reverse flotation process (Miller, 1975) was used in this study. The first stage is conventional flotation, in which coal is floated while material with higher ash and pyrite content remains in the cell. Kerosene is used as a promoter to float the coal and MIBC (methyl isobutyl carbinol) is used as a frother. In the second stage, the floated coal from the first stage is depressed using a starch-based reagent, while coal pyrite is floated using potassium amyl xanthate. In this second stage, the liberation of coal pyrite from the coal matrix seems to be an important factor for successful rejection of coal pyrite."

Jan 1, 2015

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By J. C. Purcupile

In this time of increased coal demand, a faster and safer method for roof support is needed. This report outlines the preparation and testing of a machine which we feel will help answer this need. The results of the tests are encouraging, and indicate that further exploration of the method should be continued.

Jan 1, 1975

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971

By Barbara C. Schickner

The long-awaited COSMAR study prepared under the auspices of the National Academy of Science reaches one emphatic conclusion that has been enthusiastically seconded by the mining industry: The 1977 federal surface mining act is "poorly suited" as a vehicle to regulate noncoal mining. Though the industry greeted the report with approval, the weight it will carry and the extent of its impact are yet to be felt. The COSMAR report makes no recommendations-that's a job left to the Administration's Council on Environmental Quality-and the prospect of legislation still hovers. For a closer look at the study, MINING ENGINEERING talked to COSMAR committee chairman James Boyd, a well-known presence in the mining arena for over 50 years. After highlighting some of the study's major points, Dr. Boyd comments on the report's impact and possible repercussions. Dr. Boyd, for those readers who haven't seen the COSMAR report, would you summarize some of its major findings? The committee analyzed the surface mining act to determine if it was applicable to noncoal mining and found that there were provisions of the act that either could not be met by existing technology or would be extremely difficult and not necessarily beneficial to adapt. We found that most noncoal mineral mines, despite their obvious diversity, can be considered in two major groups: 93% of all mines move 45% of all materials mined (mostly small units mining construction materials); and the few gigantic regional operations (2%)-copper, iron, phosphate, and uranium mines-that move 50% of the material. With few exceptions, neither of the two groups is amenable to the coal mining practices addressed by the act. The strip mine law was designed for coal mining, where land is regraded, revegetated, and returned to usefulness. In contrast, construction mineral quarries supply local needs for decades, remove most of the material from the immediate vicinity, and cannot be returned to their premining uses (though they have innumerable other valuable uses). The nation's huge mineral deposits require enormous capital investments, are vital to the nation's economy, and can take centuries to exploit. Any attempt to return these locations to premining use would be illogical. Pebble phosphate in Florida and red-bed copper in Oklahoma come near to meeting the conditions contemplated in the act. In addition to COSMAR's basic finding, the study also makes the following points: •Mining uses a relatively small part of the land resource, in contrast to

Jan 4, 1980

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By C. H. Bucknam

Principles of Green Chemistry provide useful guidance for sustainable mineral process development. Laboratory bench scale testing was carried out using pregnant cyanide leach solutions, and a number of commercially available mercury precipitation reagents were compared using jar testing to determine the most efficient and selective reagents for mercury precipitation. The most efficient reagent identified was sodium polymeric thiocarbonate (NaPTC).Coagulation experiments with fine diatomaceous earth resulted in a stable precipitate, with good settling properties. On line monitoring of the mercury in solution is recommended for process implementation to conserve reagent removing approximately 90-95% of the mercury with minimal silver and negligible gold losses.

Jan 1, 2004

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By R. R. Klimpel

The use of chemical reagents in flotation has been studied in great detail, e.g. (1, 2, 3, 4). Important progress has been made on the understanding of surface chemistry concepts involved in flotation. However, such scientific studies are often very complex even for rather simple idealized systems. Therefore, the deve- lopment of predictive or quantitative tools for plant engineering evaluation is still in the evolutionary stages. Until further progress in fundamental work is achieved, the operating engineer is faced with semi-empirical physical testing of reagent changes on several sizes of the actual equipment under study to be confident of the economic viability of any change.

Jan 1, 1980

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966

By D. R. Hack

Increased consumption of concrete in the Pacific Northwest has pushed aggregate resource development pressure from urban areas west of the Cascade Range to rural areas east of the Cascades. Some recent development has focused on barge and rail accessible off-reservation Indian allotments that are exempt from state and county regulations. These lands have their own unique set of challenges, especially when Federal and Tribal governments have conflicting goals and attitudes pertaining to resource development. This paper discusses issues of leasing, reclamation, Federal vs. Tribal authority, cultural resources, and the history of allotment.

Jan 1, 2002