Search Documents

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By Leon D. Keller

Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units are currently in operation on magnetite, varying in size from 16 ft diameter circular unit to a 25 ft by 100 ft rectangular unit. Additional units up to 38 ft diameter are under construction. Depending upon the application in the flowsheet, upgrading-varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to economically remove as much silica as possible may not be fully appreciated. These figures pertaining only to transportation may be thought-provoking. If a 10,000,000 ton per year plant could reduce the silica content of their concentrate by 17, a savings in boat freight alone would amount to 100,000 tons at $2.00 per ton annually.

Jan 1, 1963

By Yuting Xue, Brijes Mishra

The relaxation test on sandstone specimens showed typical behavior in pre-failure region and stepwise behavior in the postfailure region. Overall, more significant stress relaxation occurred within the failed specimens than the intact ones. Numerical simulations were conducted with pre-defined failure plane and with Voronoi tessellation to visualize the relaxation behavior. The model with pre-defined failure plane showed the key role of failure plane and asperity in simulating the step-wise post-failure relaxation behavior. The inhomogeneous stress distribution within failed specimen and the viscous deformation of intact rocks induced high stress concentration at the asperities. The observed step-wise relaxation initiated from the failure of asperity. Furthermore, the simulations with Voronoi tessellation showed time-dependent fracture development during relaxation in post-failure region. The presence of fractures completely changed the stress distribution. Stress concentration occurred at the front area of fractures and at the interacting areas between fractures. During relaxation, fractures still developed with time and the sudden significant increase in the “damage” coincided with the acceleration of stress relaxation leading to step-wise relaxation. Finally, the results showed the possibility of using residual strength as the long-term strength of failed rock.

Jun 25, 2020

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

Exploration of new resources and development of new equipment and designs are an ever changing facet of mining. New equipment to handle specialized operations is being developed and new techniques for its use explored. One such system is reviewed. Another is a potential system for handling the thinner stray coal seams between the more profitable thick seams. The availability of federal coal leases in the West is reviewed and current planning discussed. Gulf Coast lignites have been of much interest in recent months and are overviewed.

Jan 1, 1979

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without king reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county mad and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Feb 24, 1997

By Peter Zhang, Daniel Su, Bo Hyun Kim

Shale gas wells drilled in longwall chain pillars are influenced by longwall mining. Longwall mining on each side of the chain pillars can create overburden movements and induce deformations in gas well casings. If the deformations result in a casing breach, intrusive shale gas could leak into the longwall mine with serious safety consequences. This study concerns five shale gas wells in the chain pillars between two adjacent longwall panels in the Pittsburgh coal seam under a cover depth of 670 ft and a mining height of 7 ft. The gas wells were constructed with typical casing design, but a casing cementing alternative with uncemented production casings was practiced. Four production casings were uncemented, and one production casing was unintentionally cemented with good quality cement to a 535-ft depth and low-quality cement stringers from a 444- to 535-ft depth. The longwall faces passed by the shale gas wells as each adjacent longwall panel retreated. Production casings were surveyed by a multi-finger caliper after each panel was mined. No deformation was detected in the four uncemented production casings, but small deformations were detected in the partially cemented production casing. The maximum measured deformation in the cemented production casing was 0.05 in. after first panel mining and 0.06 in. after second panel mining. The casing deformations were also predicted by the FLAC3D model set up on site-specific overburden geology. The predicted deformations were in good agreement with the measurements in terms of deformation locations and magnitudes. All five shale gas wells resumed normal production after being temporarily plugged during the period of mine-by. This study provides a successful demonstration of the effectiveness of a casing cementing alternative for decoupling production and intermediate casing, and thus minimizing the influence of longwall mining in the shale gas wells drilled through longwall chain pillars.

Jul 1, 2023

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Roof stability in the belt entry is critical for safe and continuous production of coal during longwall mining. Previous studies of roof falls that occurred in belt entries have shown that the roof falls were largely associated with high in situ and longwall-induced horizontal stresses [1,2,3,4]. To properly support the roof in a belt entry, it is important to understand how longwall-induced horizontal stress changes can affect roof stability in the belt entry. Monitoring of horizontal stress changes was conducted in the belt entries of two Pittsburgh seam longwall panels oriented unfavorably to the major horizontal stress. Numerical models were also set up to investigate how horizontal stress concentrates and relieves in the belt-entry roof near the face as panel orientation changes. Both measurements and modeling results show that high horizontal stress concentrates in the belt entry roof within about 15 m outby the face. The study demonstrates that longwall-induced differential horizontal stress can be used to evaluate the horizontal stress concentration factors. The horizontal stress concentration factors change with panel orientation, resulting in high stress concentrations at orientations between 20 and 110° and low stress concentrations between 130 and 180°. Roof support strategies are given for the belt entries under the influence of high horizontal stress. For unfavorably oriented panels in weak roof conditions, supplementary support should be installed during development, and cable bolts should be anchored into a stable roof horizon. The bolting pattern should be designed to cover both entry corners and the entry center to prevent potential roof cutters and sagging.

Jan 1, 2023

By Jin Zhao, Weijie Wei, Jinwang Zhang, Xiaohang Wan, Shengli Yang

Reasonable mining-retention ratio (ratio of room width to pillar width) is vital to recovery rate and stope stability in underground mining of solid potassium salt deposits. Based on the engineering background of a solid underground potassium salt mine in Khammouan Province, characteristics of the plastic zone of the pillar, and the variation of recovery rate and stope stability under different mining-retention ratio conditions are discussed. The results show that compared with current room width (8 m) and pillar width (10 m), the optimization method of improvement of stope stability. The research results are helpful to recover as much solid potash resources as possible under the premise of ensuring the stability of stope.

Jun 25, 2024

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By George Alan Weed

The management of safety is not only the most noble, but also the most personally and financially rewarding of all the management functions. The management of safety should result in the prevention of accidents and the elimination of human suffering and loss of life. Safety management must be the number one priority of all management's production and profit objectives. For years, safety management has been a result of mockery, charlatanism and snake oil presentations dedicated to giving a quick dog and pony show. The result has been an unacceptable record of accidents and fatalities.

Jan 1, 1981

By Joseph L. Margin

From a stubborn start to record setting performances in little over a year, that is the story of the English Running Tunnel Boring Machines. The program to transfer technical information on these highly advanced machines from builder to user will be discussed as a vital link to this accomplishment. Some interesting features of these machines will be covered as well as a recounting of the various conditions that were encountered during these drives and how they were resolved.

Jan 1, 1991

By D. R. Wilburn

The worldwide budget for non fuel mineral exploration was expected to increase by 27 percent in 2003 from the 2002 budget, according to the Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes after five years of declining spending for mineral exploration. For the first time in several years, all regional exploration budget estimates for 2003 as defined by MEG would increase from similar 2002 estimates. However, MEG included 193 more companies in its 2003 survey than in 2002. As with previous MEG survey reports, estimates reflect anticipated expenditures rather than actual dollars spent. Caution, therefore, must be taken when comparing 2002 and2003 estimates or evaluating the magnitude of regional changes from year to year. Sample variations and currency exchange rates may influence year-to-year variations of MEG data. Even so, it is likely that the general climate of improved metal prices in 2003 encouraged companies that had previously left the mineral exploration sector or reduced their exploration activity to once again focus on minerals exploration or increase exploration activity and budgets.

Jan 1, 2004

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

By Jr. Schnakenberg

The automation (robotization) of coal mining activities at the face offers improvements in worker safety and productivity. The evolutionary introduction of autonomous, intelligent robotic machines to perform the most hazardous tasks may become a reality within the next 10 years. The U.S. Bureau of Mines Robotics and Automation research program is aggressively pursuing the development of the enabling technology necessary to achieve this goal. This program consists of both core and applications research, each focused on the fundamental issues of robotic technology. In the short term, the research is directed specifically to the robotization of present-day underground equipment and is being performed in a manner that can make incremental improvements in safety and productivity. The long-term goal is the development of intelligent autonomous mining systems.

Jan 1, 1990