Search Documents

By K. Oraee

A comprehensive, harmonic and sustainable development has always been a real concern of state policy makers. To reach such development, regional planning is an approach which is widely applied. This paper deals with policies adopted by a given country with rich mineral deposits, in order to accomplish a mining growth as well as economic development in relatively poor regions. In this regards, first, some worldwide experiences belonging to China, with large scale mining operations and Nigeria with a small scale mining industry, are studied. The mining industry in Iran is then considered as a case study. The study continues by categorizing and prioritizing Iranian regions based on their mining potential and the degree of development, using statistical analysis and Taxonomy and AHP techniques. Results obtained serve to provide recommendations as to where capital investments in the mining industry would produce highest returns. The approach used, together with the practical policies suggested in this paper, can be used to adapt appropriate strategies for mining development in a way that contributes to regional development and a more effective income distribution.

Jan 1, 2012

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By Joseph T. Duncan, Syd Peng, Larry G. Stolarczyk

The mining business has numerous risks: equipment availability, labor disruptions, foreign exchange rate, etc., but one of the more important risks is assessing the geology. Improving the “intelligence” of geology can and will have significant positive effect on reducing mining risk and thus enhancing operational and financial performance. The use of the advanced Radio Imaging Method (RIM-IV) on coal seams and ore bodies can create useful two-dimensional (2-D) and three-dimensional (3-D) high-resolution images that provide mining engineers with additional intelligence to better plan and improve operations. Improved operational performance will reduce costs and enable mining companies to meet market and financial commitments. For the past decade the underground coal mining industry has been moving toward “super panels” in long-wall mining, and “super sections” for room-and-pillar mining. These mining conventions employ wider faces, longer gate roads, greater room-and-pillar density, and an increased scale in the amount and complexity of mining equipment. An obvious economy of scale exists: amortization of setup investments over greater volume of coal enables mine management to reduce fixed cost per ton. Restricted by equipment considerations, face widths have currently reached about 1,100 ft. Wider longwall panels are planned, with 1,400-ft widths, but this requires an incremental step in hardware that the original equipment manufacturers will soon bring to market. However, longwall panel length has not yet reached its limits, with some panels planned up to 25,000 ft. While longwall panel length is generally dictated by reserve size and extent, practical restrictions in mine planning also include seam thickness, ventilation requirements, or restrictions involving methane drainage. Super panels have certainly enabled the industry to keep pushing the limits of productivity improvement. However, important considerations in mine planning, now and especially in the future, will be driven in large part by geological factors. While larger developments improve productivity and capture economies of scale, the fact that super panels can contain at least four times the area or coal volume means that the probability of encountering serious anomalies is at least four times greater than with the “conventional” panels. Given the increased probability of encountering anomalies, improved assessment of geology is important for super panels and super sections. Proper due diligence requires a thorough and competent evaluation of a mining property and its ore reserve. Using improved geostatistical techniques is most important, and improving the base data for the analysis is equally important. The old cliché “garbage in, garbage out” certainly applies. Also, the quality of coal reserves is (or has been) declining, so, in the future, mining will be in deeper and most likely thinner seams—and these seams appear to contain greater anomalies that threaten efficient operations. To counter the impact of reserve deterioration, the industry is moving toward greater use of geophysical tools and services. Fortunately, tools such as the Radio Imaging Method™ (RIM-IV) system have been improved and can provide the industry with enhanced 2-D and 3-D images of coal seams and ore bodies. To identify and profile the best areas of a coal reserve, geologists, engineers, and mine managers need greater intelligence in the form of RIM-IV tomographic maps of longwall panels and room-and-pillar sections. These images have enhanced the understanding of in-seam features, which in turn has improved operational plans and performance.

Jan 1, 2005

By Graham W. Gibbs

The current state of knowledge concerning mesothelioma risk estimates is reviewed. Estimates of the risk of mesothelioma exist for the commercial asbestos fiber types chrysotile, amosite and crocidolite. Data also exist on which to assess risks for winchite (sodic tremolite) and anthophyllite asbestos. Uncertainty in estimates is primarily related to limitations in measurements of exposure. Differences in the dimensions of the various fiber types and of the same fiber types at different stages of processing add a further complication. Nevertheless, in practical terms, crocidolite presents the highest asbestos related mesothelioma risk. The risk associated with sodic tremolite (winchite) appears to be similar. In chrysotile miners and millers, the mesothelioma risk has been linked with exposure to asbestiform tremolite. Exposure to chrysotile in a pure form seems likely to present a very low if any risk of mesothelioma. While the majority of mesothelial tumors result from exposure to the asbestos minerals, there are other well established and suspected etiological agents. While a practical threshold seems to exist for exposure to chrysotile, it is unlikely to exist for the amphibole asbestos minerals, especially for crocidolite. To date there is no indication of an increased risk of mesothelioma resulting from non-commercial fiber exposure in the taconite industry. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Amosite; Grunerite; Taconite; Crocidolite; Tremolite; Anthophyllite; Winchite; Risk estimation; Etiology

Jan 1, 2007

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By Steve Kral

After years of cutbacks, closures and layoffs, the mining industry is beginning to expand again. Metals prices are up and so is investor interest and confidence in the industry. Gold prices began to slowly move up in January2003 and finally cracked the $12.86/g ($400/oz) mark in early December. Silver, too, is up, as is copper. So the mining industry is feeling good about itself again and many companies are expanding existing mines and developing new ones. One side benefit to mining’s improved outlook is that companies are beginning to send more of their employees to industry conferences. Such was the case at the109th Northwest Mining Association meeting in Spokane, WA. The meeting was held in early December and attracted 1,100 attendees and 84 exhibiting companies. That is up from 2002’s attendance of about 900 people and 65 exhibitors. The theme was “A Partnership into the Future.”

Jan 1, 2004

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By Faruk Oksuz, Phillip L. Covell, Martin Doll

A series of difficult ground conditions causing high groundwater inflows and hazardous gas intrusion abruptly halted the construction of a 6.4-meter (21-foot) finished diameter and 1,890 meters (6,200 feet) long tunnel planned to serve as a 4-millioncubic meters (1-billion gallon) per day capacity river outfall for treated wastewater. Some 808-meters (2,650-feet) section of the constructed tunnel, TBM, and all other tunneling equipment were completely flooded with hydrogen sulfide laden artesian groundwater. The subsequent pumping and tunnel recovery efforts were unsuccessful and the tunnel was abandoned. In the end, the construction contract was terminated and options to redesign and reconstruct the project were re-evaluated to maximize the use of already constructed tunnel facilities such as the construction access and inter-mediate shafts and six outfall diffuser shafts in the river.

Jan 1, 2007

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

By Steve Polegato, J. Coady Marsh, Gary Landry

The Donkin-Morien Mine in Cape Breton, Nova Scotia, has successfully completed the excavation of a 7.6m (25-ft) diameter access decline over a distance of 3.5km out under the Atlantic Ocean. The tunnel, completed in December 1984, was driven through a sedimentary sequence of sandstone, siltstone, mudstone and various gassy coal seams prior to intersecting the Harbour Coal Seam where development work will commence. The tunnel was driven by a Canadian prototype tunnel boring machine (TBM) manufactured by Lovat Tunnel Equipment, Inc., Toronto, Ontario. The 7.6m (25-ft) diameter full-face shielded TBM operated at various grades from 0-20%. This paper outlines the TBM design, excavation, support and backup system utilized in the drivage. Problems encountered and drivage rates will be addressed.

Jan 1, 1985

St. Peter sandstone is an arenaceous sheet that covers large area in North America. The interest for St. Peter sandstone has been increasing due to the upward trend for hydrofracturing and the consequent need for fracking sand. This material is possesses very unique mechanical properties. On the one hand, it is brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The underground mines that are working under this condition are lacking the ground control techniques for this particular mining environment. The geotechnical properties of the St. Peter sandstone were examined using uniaxial test, triaxial test, porosity test, flexural strength test. This paper aims to investigate the effect of microstructure on strength properties, utilizing microscopic studies, index test (porosity, size distribution).

Feb 23, 2014

By Geoffrey Berry

Exposure?response relationships between the relative risk of lung cancer and quantitative measures of exposure to asbestos are available from a number of epidemiological studies. Meta-analyses of these relationships have been published by Lash et al. (1997) [Lash, T.L., Crouch, E.A.C., Green, L.C., 1997. A meta-analysis of the relation between cumulative exposure to asbestos and relative risk of lung cancer. Occup. Environ. Med. 54, 254?263] and Hodgson and Darnton (2000) [Hodgson, J.T., Darnton, A., 2000. The quantitative risks of mesothelioma and lung cancer in relation to asbestos exposure. Ann. Occup. Hyg. 44, 565?601]. In this paper, the risks derived in these meta-analyses have been compared. Lash et al., concentrated on process and found that the risk of lung cancer increased as the asbestos is refined by processing. Hodgson and Darnton concentrated on fibre type and found that the risk was highest for exposure to amphibole asbestos (crocidolite and amosite), lowest for chrysotile and intermediate for mixed exposure. Some of the differences between the conclusions from the two meta-analyses are a consequence of the choice of studies included. The range of asbestos types included in the studies in the analysis of Hodgson and Darnton was wider than that in Lash et al., enabling differences between fibre types to be analyzed more readily. There are situations where occupational exposure to chrysotile asbestos has shown no detectable increase in risk of lung cancer. Taconite miners have shown no increased risk of mortality due to lung cancer. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Amosite; Grunerite; Taconite; Crocidolite; Tremolite; Anthophyllite; Winchite; Risk assessment; Etiology

Jan 1, 2007

By Bhaskar B. Thapa

The design of the Caldecott 4th Bore, located along State Route 24 in Oakland, California, is based on the principles of the New Austrian Tunneling Method (NATM). Typical NATM initial support design practices used in Europe were adapted for this project to account for U.S. conditions and requirements, such as degree of experience with NATM construction, the prevailing contractual environment, and preferences for contractual simplicity. Key design features are: (1) support selection criteria based on ground behaviors and ground conditions; (2) a prescriptive design with allowance for support adjustments based on observations during construction; and (3) organization of support requirements into only four major support categories, while permitting some adjustment for variations in ground behaviors and conditions using a few subtypes and additional support measures.

By Thomas C. Shapiro

This is the second in a series of articles on microcomputers and applications in the minerals industry. The first article (ME, Feb., page 129) discussed microcomputer terms and concepts. This article will discuss software for geology and mining. The third article will cover plant, administrative, and geotechnical software applications. Introduction Geology and exploration are areas where computers have a natural fit. Large volumes of data need to be tabulated, evaluated, and made into maps and reports that allow geologists and management to make a decision on a project or mine. Until recently, the programs that performed these tasks were cumbersome and not user friendly by any stretch of the imagination. Learning time to become an expert in these programs typically would be six months or more. The computers needed to run these programs are expensive mainframes. Several years ago, the use of minicomputers became popular because of their lower cost. Programs were adapted to fit these smaller machines and became friendlier. With the advent of micros, many programs. were rewritten and used the screen capability more effectively, thus providing a real advance in user interface. Programs and Price The definition of micro, mini, and mainframe is becoming blurred. For the purposes of this article, micro refers to either an eight- or 16-bit computer, costing less than $10,000 and, more typically, under $5,000. Mini refers to a 16- or 32-bit computer that typically costs more than $25,000. Mainframe refers to a 32-bit or larger computer that costs more than $250,000. There is a large gray area between micros and minis, and minis and mainframes. Technology and prices are changing so fast that the traditional definitions have become almost meaningless and price has become a better guide. With the arrival of the minicomputer, costs for hardware began to fall, but the programs have tended to remain unfriendly. In some cases, the minicomputer acted as a front end to the mainframe. Cost of both the programs and minicomputers could easily run a minimum of $70,000. A total cost of $200,000 would not have been out of line. The average geologist and company would have a great deal of difficulty justifying such a purchase. The advent of the microcomputer has changed all that. For $3,500 to $5,000, one can buy a 16-bit micro and a printer. Plotters with six pens are available for $2,000 that will produce a 280- x 430-mm (11- x17-in.) map. For several hundred dollars, software is available to act as a word processor, an economic spread sheet, or to perform ground water calculations. In fact, some programs are available for free. Some of these programs are relatively easy to learn. In addition, programs are being developed daily that are easy to use. More importantly, large programs that once ran only on mainframes are being converted

Jan 3, 1984

By George E. Aiken

Agglomeration developments in the iron ore industry of North America are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. These relationships have occurred mainly during the last 20 years. Many of these changes are an outgrowth of events which involved the history of the Mesabi Range. Although magnetic taconites had been discovered in the Lake Superior area about 1870, they remained unvrorked in part for lack of concentration methods and a generally unfavorable economic climate. Some 20 years later the rich Mesabi hematites were found beginning the era of direct shipping ores which continued through World War II. These Lake Superior iron ores included reserves of an estimated three billion tons. Following World War II, decreasing ore grades and rising costs began to force the closing of many underground iron mines. The early 50's saw the beginning of the decline in direct shipping ores and a spurt in produc- tion of natural iron concentrates. However, the market for unprocessed concentrates began to decline in the early 60's as agglomerated products and foreign ore s began to dominate the U. S. market.

Jan 1, 1973

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By J. Lizak

Calcium carbonate is one of the highest volume industrial mineral products in North America. It is used in filler and extender applications, roofing products, floor tile, glass manufacture, etc. Calcium carbonate has over a dozen major filler and extender applications plus a host of minor uses. North American consumption of calcium carbonate fillers and extenders in 1991 is estimated at over 5,000,000 tons valued in excess of $400,000,000. There were five major suppliers of calcium carbonate fillers in the Middle Atlantic region in 1988 :?Bestone, Genstar, National Gypsum, Thomasville Stone and Lime, and White Pigment. With the exception of Genstar's Maryland operation, all of these operations are within a few miles of York, Pennsylvania. The Millington Group (TMG) purchased the assets of Bestone Corporation in February of 1989. TMG then seized the opportunity to strengthen its business position by acquiring National Gypsum's and White Pigment's Pennsylvania filler businesses in December, 1989 and July, 1990, respectively. By July of 1990 TMG's filler business acquisitions included six quarries and one underground mine, totaling over 1,200 acres and three processing facilities. The assets were restructured into two new companies - Delta Carbonate, Inc. and Penroc, Inc. (hereafter collectively referred to as Delta). Delta identified the assets of the three predecessor companies as undervalued from the outset. The initial phase of Delta's turnaround strategy was to reassess the combined mineral. mining, processing, transportation and marketing assets. The second phase was to effectively integrate these resources in order to exploit their inherent synergy.

Jan 1, 1992

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

Separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. Over 50% of the future phosphate reserve in Florida contains too much dolomite to process using the current industry practice. The current phosphoric acid production practice requires less than 1% MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option 1 offers three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand. These methods could reduce MgO content in the final concentrate by 20–40%. Option 2 involves crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9% MgO at about 87% P2O5 recovery. Option 3 is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012