Search Documents

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By Doris M. Hyde

In the past, mining has represented between 11% and 12% of the gross domestic product (GDP). In 1982, mining contributed over $150 million to the estimated $1.4 billion GDP.2 Overall economic growth for 1983 was projected at about 2%, primarily as a result of increased tourism. The inflation rate remained at or fell below the 1982 level of almost 4%. The Government continued its efforts to strengthen the industrial base by improving infrastructural systems and the establishment of a free trade zone. Laws against property ownership by foreigners or foreign-owned companies were strengthened, but the prohibition was softened to allow for close family inheritance. Otherwise, Government approval must be obtained to retain property acquired through inheritance, court order, mortgage, or other means. Special consideration was granted to foreign investors seeking to promote industries beneficial to the economy.

Jan 1, 1985

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By D. R. Corson

The Bureau of Mines instrumented two similarly backfilled stopes--one filled in the normal manner and the other with the fill densified using vibratory compactors--to evaluate the effect of fill compaction on subsequent vein-wall closure proposed as a adjunct process for strengthening cemented fill. Hydraulic pressure cells to monitor pressures within the fill and mechanical closure devices to measure vein-wall movement and the procedure for their installation are described. The field compaction work was generally performed manually by utilizing small commercial concrete vibrators. A prototype immersible vibrator using slusher cables to propel the vibrator in the stope was used on several lifts of fill. Although compaction efforts were less effective than anticipated in increasing the final density of fill, analysis of the field data does indicate somewhat improved strain characteristics and an increased pressure buildup for the densified fill. The effects of a prolonged period of inactivity and of rock burst occurrences in the immediate area are also reflected in plots of strain and pressure within the two instrumented stopes.

Jan 1, 1971

By G. S. Scott

The Bureau of Mines is engaged in research to assess the hazards associated with the handling, storage, and use of combustible gases, vapors, and. liquids encountered in mines and in industry. As a part of this general pro-gram, numerous limits of flammability and ignition temperatures are being investigated for a wide variety of combustible materials, and methods are being developed to minimize the explosion hazards of these combustibles. The Bureau receives numerous requests for information on the explosion hazards of specified combustible mixtures under various conditions of use. This information circular has been prepared to assist those who may have similar requests. Destined primarily for the layman with a limited technical knowledge of the subject, it considers rather briefly the numerous factors that enter into the general problem of gaseous explosions and their prevention.

Jan 1, 1951

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By J. L. Howell, D. E. Pollock, A. B. Cecala, A. D. O’Brien

Dust from worker,s clothes has been shown to be a problematic source of personal dust exposure. A recently completed effort between NIOSH and the Unimin Corporation has resulted in a quick and effective way to clean worker clothing. The process involves a booth under negative pressure with an air spray manifold to supply compressed air to blow off the dust from the clothing. The overall system is designed to meet MSHA and OSHA requirements. Results of field testing indicated that the manifold cleaned the clothes 10 times faster and removed 50% more dust than cleaning methods used by workers today.

By Andrew M. Leszcykowski

A 1981 U.S. Bureau of Mines investigation indicates the Panamint Dunes Wilderness Study Area (WSA) has one active (intermittent) mine,--borrow pit MS 242 owned by the California Department of Transportation (Cal Trans). This mine produces cinders for road base and traction grit. It contains about 900,000 tons of inferred reserves. Examination and sample analyses indicate the Panamint Dunes deposit, covering about 480 acres of the WSA, may have silica resources and the Green Quartz Claim may have copper resources. Carbonate rocks occur in the WSA, but stone resources have not been identified. Adjacent to the WSA, the Big Four Mine contains 35,000 tons of inferred subeconomic zinc-lead-silver resources, and may have additional resources. Sample analyses indicate the Apple 1 Claim, also adjacent to the WSA, may have silver-lead-zinc resources.

Jan 1, 1985

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By G. A. Smyres

The Bureau of Mines investigated a HCI-02 leaching procedure to recover Cu, Ni, and Co from a low-grade bulk sulfide flotation concentrate prepared from the Duluth gabbro complex. Since the Duluth gabbro complex is the largest known and unexploited Ni resource in the United States, the development of options for extracting the metal values from the flotation concentrate of this domestic resource is necessary. Conditions were determined for producing a pregnant solution low in Fe to facilitate recovery of the metal values. Leaching experiments were conducted at 15 pct solids, 1000 to 1200 C, 0.2 to 0.3 g HCI per gram concentrate in a 50-gal reactor pressurized to 50 pSig with 02. Base metal extractions from the concentrate were, in percent, 90 to 92 Cu, 99 Ni, 97 to 99 Co, and 0.1 .Fe. Precious metals extractions were erratic and unpredictable; at best their extractions were, in percent, 55 Au, 90 Ag, 40 Pt, and 45 Pd. The reaction time at 1200 C was 0.5 h. The use of compressed air instead of 02 as the oxidant was also investigated. Solvent extraction using LIX 622 was used to remove Cu from the pregnant solution. Cementation on Cu was tested for precious metals recovery, while sulfide precipitation was used to produce a Ni-Co product. A conceptual flowsheet for treating the Duluth gabbro concentrate is proposed.

Jan 1, 1985

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By Frank M. Vodoklys

This is the final report on Contract H0220049 covering the period from 27 April 1972 to 30 April 1974. The objective of the contract was to develop and evaluate materials and methods to achieve post explosion identification of explosives reliably and economically through the use of phosphor coded grains incorporated into the explosive during its manufacture. A coding system of two spotting phosphors and seven coding phosphors was successfully developed during the execution of the contract. The ability of the coded grains to survive detonation in many different types of explosives was demonstrated and the complete code was extracted from a single 100 micron post-explosion fragment. A method was established for testing grain strength to correlate with field test results and an optical system was designed for extracting the code from the grains. Also in fulfillment of the contract requirements a laboratory method for manufacturing the coded grains was established and ten one-pound samples, each with a different code, were fabricated. Finally, a method was developed for applying a coating of polyethylene to the grains to prevent sensitization of the tagged explosives and the ten one-pound samples were coated and delivered to the Bureau of Mines.

Jan 1, 1974

By J. A. Kosek

Work has been conducted under Bureau of Mines Contract Number HO 357078 to develop instruments for detecting CO, NO and NO2 in a mine atmosphere, using fuel cell technology. The approach has been to optimize the fuel cell sensor configuration for the specific detection of CO, NO and NO2 in the presence of other mine gases utilizing recent advances in catalyst, electrode and solid polymer electrolyte membrane technology. Para-metric testing has been conducted on three electrode sensor cells to define performance and life characteristics as a function of temperature, feed flow and applied sensor voltage. Extended life testing has been performed on sensor cell configurations exhibiting favorable characteristics. Reliable, efficient gas sampling and electronic control circuitry has been fabricated for use with the sensor cells, and integrated into devices to meet the performance and design specifications for portable, battery-powered, hand held direct indicating gas detectors for use underground. Twenty of the production-type, direct indicating CO detectors have been tested and delivered to the Bureau of Mines under the present contract. Three prototype diffusion head CO monitors have also been delivered for evaluation under the pre-sent contract. The gas sampling pump and related parts have been replaced by a diffusion tube assembly in which CO reaches the sensing electrode surface by diffusion alone. In addition, delivery will be made of ten direct-indicating nitric oxide detectors and ten direct-indicating nitrogen dioxide detectors. These instruments are very similar in design to the direct indicating CO detector.

Jan 1, 1979

By Hillary W. St. Clair

This is an initial progress report on a theoretical study of the iron blast furnace. The purpose is to develop a thermochemical model that will simulate mathematically a real furnace. An analysis is made of the behavior of a hypothetical furnace, operating adiabatically on pure ferric oxide, graphitic carbon, and dry air. Relationships are derived for carbon consumption, gas composition, and reaction temperature for a furnace operating at steady state, and in which the smelting rate is slow enough for the gas and solids to approach thermal and chemical equilibrium. Analyses are made for two contrasting types of gas flow: (1) Nonturbulent flow, having no vertical mixing; and (2) turbulent flow, having perfect mixing during each step of the process. It is shown that some vertical mixing is essential for complete reduction of ferrous oxide and that the extent of vertical mixing is one of the critical factors in the behavior of the furnace, This analysis indicates that the thermochemical relationships in a blast furnace can probably be best simulated by a finite series of gas-solid reactors through which gas and solids flow countercurrently and in which the temperature and composition of gases and solids are assumed to be uniform. Any degree of vertical mixing can be approximated by the proper choice of the number of reactors.

Jan 1, 1963

By A. H. Shoemaker

This paper describing the mining practices at the Old Dominion mine, Globe, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various minim districts in the United States. The Old Dominion mine is situated in the eastern port of the Globe-Miami district, about 1-1/2 miles north from the center of the town of Globe. An average of nearly: 1,200 tons per day was mined during 1928. The prevent production is about 1,500 tons per day; of this amount,, approximately 100 tons is direct-smelting ore that is shipped to the smelter at Miami and 1,400 tons milling ore which is treated in the company?s concentrator at Globe. About 600 men are employed at the mine.

Jan 1, 1930

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By H. D. Kline

This publication describes methods and techniques of mining and crushing limestone at 3 of 11 small quarries operated by Anderson-Oxandale Rock Co. in northeast Kansas in 1959. It is one of a series of reports by the Bureau of Mines on methods and costs of mining in various mining districts in the United States. The three quarries selected for study -Bosse quarry, Pottawatomie County; Hansen quarry, Morris County; and Huston quarry, Dickinson County (fig. 1) -were in many respects similar to many others that had been developed solely to fill local and usually transitory demands for crushed limestone for use as concrete aggregate, roadstone, and soil conditioning. Factors governing the choice of quarry sites were quality of limestone, shallow overburden, and proximity to points of consumption of the crushed stone.

Jan 1, 1962

By James C. Fowler

This report contains a description of the contract activities performed by ENSCO, Inc. under contract H0292025. The purpose of this project was to prove the feasibility of detecting hazards in a coal seam using a synthetic pulse radar. This work was conducted in three phases. The first was an analysis of the types of errors which might cause problems. The second was to build a breadboard radar and the third phase was to conduct a field test with the system. The work from each phase is discussed and the results of the field tests are presented. These results show propagation of the radar signal through 200 feet of coal along with reflections from 50 feet away. The final section contains recommendations for future development.

Jan 1, 1981