Search Documents

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager's yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By Edward J. McNamara

People in the real estate industry are fond of saying that the three most important features of a piece of property are, in order, location, location, and location. This is perhaps the reason that the owners of a well known high-end restaurant chain chose to spend $15 million dollars to renovate 5000 square feet of basement in a 22-story commercial building in the heart of New York City's Time Square. The goal was to create a music club with a stage area and dance floor with a mezzanine level surrounding the dance floor. In order to create the 50' x 40' dance floor and 20' x 40' stage area, 3 concrete columns were removed. New transfer girders were used to transfer the loads of these columns to new steel columns. For the mezzanine, nine columns had to be underpinned. All work continued while the restaurants, shops and offices above carried on business as usual. This paper details some of the means and methods utilized as well as the challenges faced by Underpinning & Foundation Constructors, Inc. in underpinning the columns and installing the new transfer steel.

Jan 1, 2000

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By Thomas C. Anderson

Tiedback walls are now recognized and accepted as a good solution for a variety of structural problems: ? Retaining Walls and Bridge Abutments in cut situations ? Landslide stabilization ? Repair/support of existing walls Acceptable techniques have been developed for anchoring in cohesive and granular soils and in any kind of rock. Methods have been developed for adequately protecting tieback tendons against corrosion and for testing every tieback to verify its long-term load-carrying capacity. However, the major problem that the industry faces today is how do we get constructable and economical tiedback walls contracted for and built with minimal claims. This paper will explore the issue of "constructability" through a look at specific problems from actual projects. From a research report from the Construction Industry Institute, Austin, Texas (1986), constructability is defined "as the optimum use of construction knowledge and experience in planning, design, procurement and field/operations to achieve overall project objectives." Maximum benefits occur when people with construction knowledge and experience become involved at the very beginning of the project." The design and installation of tiebacks has been developed primarily by specialty contractors; each contractor has evolved its own methods of performing the work, and consequently, many of the techniques are patented and proprietary. The real question is, how do we make effective use of this knowledge and experience during the design phase of the project?

Jan 1, 1991

By Luo Yang

A one-dimensional wave equation based algorithm for estimation of shaft and toe resistance of driven piles using High Strain Testing (HST) data is presented. The pile is represented by a uniform elastic bar, while the soil around the pile is assumed as a homogenized isotropic medium, and Smith model is adopted to represent soil-pile interaction in the wave equation analysis. In most cases, the displacement of pile particles along pile shaft is greater than recoverable soil deformation (i.e., soil quake in Smith model). Therefore, static shaft resistance could be reasonably assumed to be totally mobilized during pile driving. Smith damping factor is used to account for combined dynamic and rate effect. Force and velocity time histories measured at the pile head are used as input boundary conditions in an analytical solution of the one-dimensional wave equation. As a result, two unknown parameters, static shaft resistance and Smith damping factor, can be incorporated into the one-dimensional wave equation and determined analytically for the time duration prior to the first downward wave reaching the pile toe. Then, soil resistance and Smith damping factor at pile toe can be further determined. The advantage of the proposed analysis technique is that the Smith damping factor and the static soil resistance can be directly determined based on the closed-form solution of the one-dimensional wave equation, which is computationally efficient. Numerical examples are given to illustrate the use of the proposed method to determine the pertinent Smith model constants and the static resistances.

Jan 1, 2006

By Mohammad Nasim

Vertical expansion of existing structures frequently requires foundation retrofitting to enhance the capacity of existing foundations for supporting additional loads. Owing to their small diameter, a variety of suitable drilling methods available for installation, and smaller installation equipment capable of operating under limited headroom conditions, micropiles are often preferred for foundation retrofitting. This paper presents a case history demonstrating application of micropiles to underpin the existing foundation of the Washington D.C. Children?s National Medical Center (CNMC) for its future expansion. Located at 111 Michigan Avenue in northwest Washington, DC, portions of the hospital currently extend five stories above grade and three levels below-grade as parking garages. The hospital intends to expand the surgical wing up to the current build out (five stories) above the remaining portion of the existing parking garage. The original foundations consist of 80-ton Raymond Step-Tapered piles. New loading on the foundations required each Raymond pile to be capable of supporting 150 tons. Results from quick load tests on existing piles indicated that two entire column lines (Column Line A and B) would experience loads beyond their capacity, requiring enhancement of the existing foundation at these locations. The design and construction of the foundation upgrading work was particularly challenging due to various project constraints related to a high groundwater table, micropile installation under limited head room, and ensuring that the parking garage remained fully operational for the entire duration of construction. The paper presents the challenges faced during testing of existing foundations amid a high groundwater table, design developments of underpinning options to support the additional column loads, difficulties and challenges encountered during installation of the micropiles and construction of the micropile pilecaps, and value engineering options developed during various phases of the project. Understanding that micropiles are often a preferred option for foundation retrofitting, the case history is expected to provide a baseline design approach and innovative solutions to typical challenges faced during construction, thereby reducing potential cost overruns during design development and construction of similar future projects.

Jan 1, 2008

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Thomas A. Printz

The wide use of carbon steel in construction and engineering projects makes this engineering material accountable for approximately 85% of the total annual steel production worldwide. Despite the lack of corrosion resistance of carbon steel, it is incorporated into the permanent work for marine applications, power plants, transportation projects, chemical processing, mining, petroleum production and refining, pipelines, mining and construction equipment. Corrosion is an electro-chemical process that occurs in the presence of water and air. When an electric current is introduced to water or soil, the rate of carbon steel corrosion increases rapidly. Gaseous atmospheric constituents that are capable of electrolytic activity can also increase the rate of corrosion. Corrosion tends to be more rapid in environments in which the steel is exposed to water, and then air, rather than being constantly submerged. The exposure to seawater increases steel pitting because the electrical conductivity is improved in salt water.

Jan 1, 2013

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013