Search Documents

By Richard D. Luark, Fernanda S. Madrona

Designing temporary retaining systems that allow for deeper excavation amid the existing urban infrastructure has become a challenge. A 60-foot-deep excavation in downtown Seattle was required to construct five levels of below grade parking for a 35-story high-rise building, Tower 12, next to an existing 20-story tower with three levels of below grade parking, separated from the project by an 18-foot wide alley. The solution was to combine two temporary excavation support systems, soil nailing and anchored soldier piles, to work within the site constraints. Densely-arranged, short-length soil nails were used to support the upper 30 feet of the excavation, while the lower 30 feet of the excavation was supported with soldier piles combined with steeply-inclined, high-capacity ground anchors, which extended below the adjacent building foundations. The combined temporary support system eliminated the need for internal bracing, reducing construction cost and schedule. The performance of the combined soil nail and soldier pile system was monitored with an inclinometer and optical survey monitoring, which demonstrated the performance of the combined temporary support system. This paper provides a discussion of the advantages of combining different excavation systems and an analysis of movement monitoring data collected. SITE CONDITIONS AND PROJECT INFORMATION Tower 12 consists of a 0.45-acre development with 36-stories of mixed, residential and commercial use with four levels of below grade parking. The project site is bounded by the Cristalla Condominium to the north, Virginia street to the south, 2nd Avenue to the East, and an 18-foot wide private alley to the west. The One Pacific Tower Condominium, which has three levels of below grade parking, was located to the west across the alley. A site layout plan is presented as Figure 1. As shown in Figure 1, the construction of the west wall required a maximum 51-foot-deep excavation, from elevation (EL) 162 feet to EL 111 feet. Adjacent to the west wall, the existing alley grade varies from elevation 154 to 161 feet, leaving a narrow block of soil 18 feet wide and up to 42 feet high to be shored along the alley in order to reach the One Pacific Tower bottom of mat foundation at EL of about 120 feet. In addition to the existing One Pacific Tower Basement wall, site constraints included existing utilities along the alley such as an existing 4.5-feet wide by 7-feet high vault, with bottom at approximate EL 146 located 10 feet from the back face of the proposed Tower 12 basement wall.

Jan 1, 2019

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY consists of a dual-span 1,982.5-ft long cable-stayed bridge with approach spans of 2,545 ft on the NJ side and 2,788 ft on the NY side. The bridge is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Drilled shaft resistances for design were based on load tests as described in a companion paper (Dapp et al. 2016). This paper presents the main foundation design considerations and challenges. The approach to construction of the rock sockets, with a focus on quality in order to support the use of high nominal values of side and base resistance, is described. Lessons learned from this project and their application to future similar projects are presented.INTRODUCTION AND BACKGROUNDThe Goethals Bridge Replacement (GBR) project is a Public-Private Partnership (P3) that represents a major milestone for the Port Authority of New York and New Jersey (PANYNJ) in its distinguished history of bridge building in the greater New York City metropolitan area. The new bridge will replace the existing Goethals Bridge, named after Major General George W. Goethals, Chief Engineer of the Panama Canal and the first consulting engineer for the Port Authority. The existing Goethals Bridge along with the Outerbridge Crossing and the Bayonne Bridge comprise the three Port Authority bridges connecting Staten Island with New Jersey. The existing Goethals Bridge and the Outerbridge Crossing are cantilever truss structures and both opened on the same day in 1928. They were designed by J.A.L. Waddell under the supervision of the eminent engineer Othmar H. Ammann (1879-1965), who was the designer of many other iconic bridges in the NY City area including the Bayonne Bridge (1931), the George Washington Bridge (1931), and the Verrazano Narrows Bridge (1964). The designer of record for the replacement Goethals Bridge is Parsons Corporation, which is the successor firm of Robinson & Steinman, whose principal David B. Steinman was also a notable NY area bridge designer and a contemporary and rival of O.H. Ammann.The replacement Goethals Bridge is supported on over 200 rock-socketed drilled shaft foundations. Each main pylon tower is supported on a group of six 9-ft diameter drilled shafts and each anchor pier is supported by two 10-ft diameter shafts. Each approach pier consists of a two-column bent with each column supported on a rock-socketed drilled shaft. A rendering of the Main Bridge crossing the Arthur Kill is shown in Fig. 1."

Jan 1, 2016

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017

By Mohamed Hassan, Matthias Seip, Steffen Leppla

In the east of Frankfurt am Main, Germany, a new high-rise building is planned directly next to the river Main. The high-rise building will have a height of about 75 m and will be founded on a Combined Pile-Raft Foundation (CPRF) in the tertiary marl. The new structure will be constructed next to important, sensitive traffic infrastructure. The foundation of the new high-rise building adjoins directly existing historic quay structures, which are more than 100 years old. For analysis of the stability and the serviceability of the heavily eccentric loaded foundation of the new high-rise building and the existing structures and for the investigation of the soil-structure interaction complex three dimensional, non-linear numerical simulations have been carried out. These numerical simulations take into account all geometric and material specific boundary conditions, including the history of the construction of the whole area. The paper introduces into a very complex construction project in which the investigation of the soil-structure interaction has an important role. The three-dimensional numerical simulations are explained and the results are shown.

May 1, 2022

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By Osamu Taki

The innovative Soil-Cement Mixed Wall Technique emerged in Japan and obtained recognition in the engineering and construction communities in the 1980's. This technique was introduced to the United States in 1986. It was accepted as the most credible construction technique by the U.S. Bureau of Reclamation for ground stabilization and cutoff wall work in the Jackson Lake Dam Project, Wyoming in 1987 and 1988. It was also accepted as a remediation technique by U.S. EPA for a Superfund Innovative Technology Evaluation (SITE) demonstration on in-situ solidification/ stabilization. The Soil-Cement Mixed Wall Technique consists of mixing in-place soils with cement grout or other reagent slurries using multiple axis augers and mixing paddles to construct overlapped soil-cement columns. The overlapped column panel is then extended to form an underground continuous soil-cement wall for use as a cutoff wall or a structural diaphragm wall for groundwater control and excavation support. By arranging the column panels in various configurations, the technique becomes a versatile tool for stabilization of soft or liquefiable soils.

Jan 1, 1990

By Dileej M. Dewaikar, Poonam A. Patil

"In this paper, the ultimate lateral resistance of a long, flexible, unrestrained vertical pile in a cohesive soil is computed under static loading condition using py curves. A simple and improved method for the construction of hyperbolic p-y curves for a cohesive soil is proposed for static loading conditions. An iterative analysis is employed with secant modulus approach, using a matrix method known as moment area method developed by Sawant and Dewaikar. The loadground line displacement relationship is obtained for different load eccentricities using p-y curves developed by Matlock, Georgiadis et al. and the proposed hyperbolic p-y curves for different eccentricity ratios. These values are compared with the values computed from model test performed by Rao et al. and with the limit equilibrium solution given by Broms. The comparison shows that, the results obtained using hyperbolic p-y curves shows a better agreement with the model test data with the maximum difference within 15% using other methods; whereas Broms' limit equilibrium solution shows some agreement with the results based on Matlock's p-y curves.INTRODUCTIONPile foundations are used for jacket type offshore structures, which are subjected to large magnitudes of lateral loads due to lake or ocean waves, winds and ice forces. The failure of a pile-soil system is catastrophic and excessive deflection of the pile creates operational difficulties. In the view of this, bending moment in the pile is required to be predicted in a rationar manner. The p-y concept developed by Reese and Matlock (1956) is popularly being used to estimate the pile top deflection and bending moments.The ultimate lateral load which causes collapse of a pile-soil system is generally estimated using Broms' (1964) method, which is based on limit equilibrium considerations. The p-y curves are basically nonlinear in nature and include ultimate pressure at the depth where they are generated. Therefore, if the lateral deflection of pile top against different magnitudes of lateral load is obtained, it should be possible to obtain the ultimate lateral load from this load-deflection relationship."

Jan 1, 2005

By H. Hayashi, M. Yamaki, H. Hashimoto, T. Yamanashi

"In an experiment on a trial embankment, the deformation mode of the improved ground at the toe of the embankment was compared with the deformation mode of the unimproved ground. This comparison showed that the behavior exhibited by the improved ground was the same as that exhibited by the unimproved ground, despite the low improvement rate (ap = 10%) of the ground improvement. Thus, the improved ground and the unimproved ground were found to be functioning as composite ground. Further, the strain that developed in the geo-textile used for the crushed-stone mat was considerably less than the strain specified by the design strength. As a result, it was found that a crushed-stone mat can serve as a mattress.OVERVIEW OF THE TEST CONSTRUCTIONLow Improvement-Rate Soil in Combination with Crushed-Stone MatIn Hokkaido, approximately 2,000 km2 of the land is peat land, an area almost as large as Tokyo. Such land accounts for 6% of Hokkaido’s plains and 2.4% of its total land area. The peat layer is normally 3 to 5 m thick and underlain by a layer of soft, cohesive soil whose thickness may exceed 20 m. In such a ground, consolidation using cement may generate differential settlement between improved soil as a result of embankment construction or lateral deformation caused by the slipping of unimproved ground. Therefore, the improvement ratio (ap) is designed to be at least 50% by the Manual for Construction on Soft Peaty Ground (CERI, 2011 [1]). Consolidation of ground with a low improvement ratio in combination with crushed stone-mat installation is a measure for soft ground (Figure 1). In this method, soil with a lower Improvement ratio than that of conventional improved soil (e.g., ap=10%) is placed beneath the entire embankment and a “crush stone mat”, a layer of crushed stone (t=0.5 m) enclosed by geo-textile, is then placed between the embankment and the soil."

Jan 1, 2015

By Brian Koch

Michels installed 242 drilled shafts to support the piers for a new basket-handle, true-arch twin bridge across the Mississippi River from Moline, IL to Bettendorf, IA. The installation of the drilled shafts was completed with the simultaneous use of two Liebherr LB36 and one IMT 300 drill rigs. Utilizing barges, 233 drilled shafts were installed in the river. Michels crews also installed 7-ft to 10-ft permanent steel casing into the bedrock, and drilled to depths of 60 feet for each shaft. Despite working in strong currents, freezing temperatures and on rocking barges, Michels crews placed the shafts within 3 inches of plan position. Since the drilled shafts are the key piece in supporting the bridge structure, Michels provided cross-hole sonic logging to verify the integrity and strength of the concrete within the shafts and to add another level of quality control for the owner/customer. Extensive planning took place each day to ensure that tugboats, the linchpin of the project, were being efficiently utilized to shift the barges and materials daily. On any given day, Michels transported five concrete trucks by barge from shore to shaft sites to pour between 40 and 240 cubic yards of concrete. The Michels environmental team was diligent with preparing, discussing and implementing a water treatment plan that was accepted by all state and federal agencies and adhered to strict environmental regulations. Grain hopper barges were rented to control and treat the water that was used in the drilling operations. Another challenge crews ran into was the discovery of caverns when drilling into some parts of the bedrock. Michels worked with the engineer to develop a plan to construct the drilled shafts that encountered the caverns.

Jan 1, 2019

By Abhijit R. Sheth, Craig M. Benedict, John Brun, Ara G. Mouradian

"Amtrak recently replaced the 1907-era bascule two-track bridge over the Niantic River between East Lyme and Waterford, Connecticut. The project included new approach embankments, with approximately 2,500 lineal feet of retaining wall along the west approach and 780 lineal feet of retaining wall along the east approach. The paper focuses on the design and construction of the east approach retaining wall, whose alignment is directly adjacent to an existing wetland area which required protection. An anchored prestressed concrete sheet pile retaining wall was selected for the east approach. A combination of concrete anchor piles and ground anchors were used to support the wall. The design of the wall took into account two simultaneous train live loads, support of electric traction catenary structure foundations, and construction live load, while at the same time preventing permanent impacts to the adjacent wetlands. The design considered challenging subsurface conditions, shallow groundwater, the close proximity of the existing operating tracks, construction staging, and storm surge events in Long Island Sound.INTRODUCTION AND PROJECT HISTORYThe National Railroad Passenger Corporation (Amtrak) recently replaced the 1907-era bascule two-track bridge (No. 116.74) over the Niantic River, between East Lyme and Waterford, Connecticut, along the heavily-traveled Northeast Corridor (NEC). The two NEC tracks, which carry over 50 trains per day, run east-west over a narrow spit of land known as “The Bar”, which separates the Niantic River’s marine estuary to the north from the Niantic Bay to the south, before crossing the river. The bay is an arm of Long Island Sound and is occasionally subject to storm surge from hurricanes.The 1907 bridge was built as a replacement for the previous 1891-era swing-span bridge, and was constructed parallel to, and 49 feet north of, the swing-span structure. The two-track 1907 bridge consisted of a single-leaf bascule span and four approach spans supported on stone masonry piers and abutments. The new bridge increases horizontal navigational clearance for marine traffic in the river from 45 feet to 100 feet, and vertical clearance from 11.5 feet to 16 feet above mean high water with the bridge in closed position. The new bridge, constructed 58 feet south of the 1907 structure, features a single-leaf bascule span of 141.5 feet, with an approach span on either side."

Jan 1, 2017

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Amr Al Degwe, Walid Jaber

"INTRODUCTIONNSCC International Ltd. carried out the enabling works and constructed the foundation system for the Emirates Pearl Tower and Bab El Qasr Hotel in Abu Dhabi. Emirates Pearl Tower is a joint venture project of TDIC- Tourism Development and Investment Company and ATLAS group, a leading telecommunication company in the UAE. Bab El Qasr Hotel is a project of EMROC Emirate-Moroccan General Trading & Investment Company. The combined enabling project is executed under the combined management of JACOBS International Holdings Inc. and NASSAR Engineering Services.The project is located to the south-east of Emirates Palace and west of Etihad towers, at about 20m away from the sea shore. Since the two projects are located next to each other a combined shoring system was constructed for the entire area. This decision was based on an agreement with clients and consultants of the two projects and resulted in significant savings for both parties. The shoring system consisted mainly of diaphragm wall with ground anchors and steel struts. Cantilever secant piles were used on the eastern side of the plot, adjacent to Etihad Towers` basement.PURPOSE AND SCOPE OF WORKNSCC International Ltd. was responsible for the design, procurement and construction of strutted and anchored diaphragm walls and cantilever secant piles. The shoring layout and a summary of shoring sections are shown below."

Jan 1, 2017

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By Charles M. Wilk, Lori Tiefenthaler

"Information presented in this paper can be used to support deep soil mixing, subsurface grouting and slurry wall technology as sustainable construction technologies. Ordinary Portland Cement (OPC) is the default cementitious material used by Deep Foundation Institute (DFI) Members for geotechnical work. Owners, engineers and contractors can contribute to the sustainability of a geotechnical project by increasing the use blended hydraulic cements and industrial byproducts to replace some of the OPC in mix designs. Sustainability is defined as the quality of not being harmful to the environment or depleting natural resources. Production of cementitious materials consumes natural raw materials and energy while also generating air emissions and waste. Life Cycle Assessments can be used to compare the relative environmental impacts of one cementitious material to another. Blended hydraulic cements (BHCs) are interground (or blended) mixtures of Supplementary Cementitious Materials (SCMs) with OPC. Commonly used SCMs include fly ash, ground granulated blast furnace slag (GGBFS) and limestone. Examples of industrial byproducts commonly used in geotechnical work include coal combustion residuals (CCR) (aka fly ash), and ground granulated blast furnace slag (GGBFS). Much of life cycle impact of these SCMs and industrial byproducts have already been borne by the industries that generated them. There is increasing awareness to LCA and sustainability of different materials used on projects. This is evident in the application of the Leadership in Energy and Environmental Design (LEED) program. The savings in environmental impact with the use of SCMs and industrial byproducts can make proposed use of these materials in a geotechnical project more attractive in terms of sustainability. This paper presents (a) information that compares published life cycle assessment data of OPC, BHCs, and slag cement (SC) to illustrate the potential benefits to sustainability and (b) general strategies for positioning a geotechnical application, use, project design or cementitious material mix as a more sustainable alternative"

Jan 1, 2017

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019