Search Documents

Once applied, EarthZyme reduces the tendency for a road to exhibit common maintenance issues: wash-boarding, rutting, heaving, potholing and dust.

Aug 1, 2013

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013

By Amin Saravari, Jamal Jafari, Abbas Sam

"The fourth concentrate production plant includes the comminution systems and the medium-low intensity magnetic separators (LIMS). Based on different conditions, two types of materials are fed into the plant. Type A: 70% of mine ore and 30% of reject materials from magnetite plant and type B: 100% of mine ore. The goal of the present study was to increase the iron grade and the blain number with low sulfur content in final concentrate as the pellet feed. An appropriate pellet feed should have more than 67% of iron, less than 0.1% of sulfur and a Blain number of more than 1800 cm2/g. The Fe, S and Blain no. amounts for the present concentrate are 66.6%, 0.95%, and 500 cm2/g (feed type:A) and 67.8%, 2.3%, and 450 cm2/g (feed type: B), respectively. In this research, the plant improvement efficiency was evaluated by changing the feed particle size distribution and using the flotation system. Laboratory experiments were designed based on the three circuits:1) LIMS (Low Intensity Grinding Rolls) feed grinding-LIMS test-flotation test2) LIMS feed grinding-flotation test-LIMS test3) LIMS concentrate grinding-flotation testThe best results were obtained using the first circuit at the LIMS feed size (d80) of 132 ?m. The processing results using the circuit no. 1 (feed type: A), showed a LIMS concentrate with 69.8% of Fe and 0.36% of sulfur. In this case, the final concentrate (after flotation) with Fe grade of 70.3%, sulfur content of 0.07% and Blain no. of 1571 cm2/g were obtained. In case of the feed type of B, the LIMS concentrate with Fe grade of 68.7%, and sulfur grade of 1.6% was achieved. Also, the Fe and sulfur contents were 69.3%, and 0.4% respectively with a Blain number of 1112 cm2/g. According to the obtained results, it was suggested that a LIMS feed comminution along with a LIMS and flotation systems are necessary to achieve an appropriate iron and sulfur grades with an acceptable blain number. To reach a concentrate Blain number as a pelletizing feed, a High Pressure Grinding Rolls (HPGR) system at the end of the processing line was recommended."

Jan 1, 2016

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By H. Z. Liu, J. M. Zhao, F. C. Wang

"Novel silicate-alginate composite beads containing 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester (P507) were synthesized and applied for the adsorption of Nd3+ from aqueous solutions. The adsorption amount of Nd3+ has been increased owing to the introduction of P507. The effect of equilibrium pH (pHe), the kinetic and isotherm experiments were investigated. The adsorption reaches equilibrium at 9 h and the maximum uptake capacity is up to 195.4 mg/(g dry adsorbent). The Langmuir isotherm equations are used to describe the adsorption process. Complete desorption can be realized with 0.2 M HCl within 20 min. INTRODUCTIONRare earth elements (REEs) have found various applications in different domains, such as metallurgy industry, ceramic industry, nuclear fuel control, photo-electro-magnetic functional materials owing to their unique properties. Neodymium (Nd), as a representative of all of the most valuable REEs, is widely used as catalysts, laser crystals, capacitors, rubber additives, Nd-Fe-B magnets, hydrogen storage and so on. Thus, the separation and purification of neodymium is significant. Unfortunately, Nd always coexists with other REEs and selective separation of the individual Nd from the REEs mixtures is still extremely difficult owing to their strictly similar atomic structures and chemical properties.Liquid-liquid extraction (LLE) and solid-liquid adsorption (SLA) are the most widely adopted techniques for the separation of REEs in the hydrometallurgical fields. The LLE process is well suited for large-scale continuous operation because of its inherent high capacity and fast kinetics. Nowadays, as a commercial extractant, 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (P507) has been extensively studied for extraction and separation of REEs since it has considerably good extractability and high separation efficiency (Xu et al., 1992). SLA is one of the effective and green separation methods with some prominent advantages, such as easy regeneration of adsorbents, small footprint size, less industrial wastes, higher enrichment factors and column efficiency,rapid solid–liquid separation without emulsion and so on. Hence, the introduction of extractants with excellent performance into adsorbents will integrate the advantages of LLE and SLA (Lee et al., 2009)."

Jan 1, 2012

By R. Laucournet, E. Billy, M. Joulié

Today Li-ion batteries are considered as one of the most attractive available energy storage solutions. However in order to overcome environmental, legislative and economic issues, the management of used batteries has to be considered and mainly the recycling. The present paper deals with the recycling of used Li-ion batteries and the recovery of high value metals from active materials of electrodes. Lithium nickel cobalt aluminum oxide (NCA) and lithium manganese nickel magnesium oxide (LMNM) cathodes, which contain most of valuable elements typically used in the composition of active materials for Li-ion batteries are investigated by a hydrometallurgy route. The process is divided into two steps: the materials leaching and the elements recovery by a selective chemical separation. Some experimental parameters (acid nature, concentration, time and temperature) are studied to determine the most efficient conditions of dissolution. Then, the valuable elements such as nickel, cobalt and manganese are selectively recovered with a high efficiency close to 100 % and with a high purity by precipitation. By this study, an adaptable hydrometallurgy process can be defined according to the composition of Li-ion batteries to recycle.

Jan 1, 2014

By G. A. Witwicki

"The Thyssen Mining Group of Companies has successfully applied ground freezing technology to numerous projects throughout Europe and North America for over 100 years. Recently, the aspect of data acquisition and data verification has received greater focus.Thyssen Mining has been engaged in several relatively deep shaft sinking projects over the past five (5) years, all of which have required ground freezing to successfully sink through water bearing rock. To safely and economically sink through a quantity of water similar to Saskatchewan’s Potash Mines, it is imperative to understand freeze wall thickness and growth rate.Critical to understanding freeze wall thickness and growth rate, is the collection of accurate data as well as the interpretation of those data. The data can then be utilized to gain a better understanding of the freeze wall growth rate in active projects as well as to provide data to be utilized in modeling for future projects.This paper elaborates on the installation and operation of the data acquisition system utilized at the Newmont Leeville project, Nevada’s first frozen shaft project. In addition, this paper elaborates on the methodology developed by Thyssen Mining to manipulate the freeze wall data derived through the data acquisition system.The successful incorporation of the new system of collection and analysis of freeze wall data for the Leeville Project has given Thyssen Mining a high degree of confidence in the understanding, as well as prediction, of the ground conditions during shaft sinking.This paper will include:•,A brief description of ground freezing and its objective;•,An overview of previous data acquisition methods employed;•,Current data acquisition methods;•,Installation requirements; and,•,Data manipulation and presentation methods."

Jan 1, 2015

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By H. Ishimoto

It always has been a serious issue to improve safety in mine sites, demolition work sites, and civil engineering work sites. Especially, collision accidents caused by construction equipment damage not only the productivity of operations but also the health and life of workers in those work sites. To solve this problem, a variety of worker auto-detection means are developed so far, but they have not still become widely used in actual worksites. There have been two controversial points in the prior methods. One is that they were not enough in respect of the detection accuracy and certainty, and the other one is that the information of the detection results was not comprehensible to the operator of equipment. In this paper, the functional requirements of the obstacle detection system in earth moving work site is redefined at first, and then, it is proposed to apply a stereo vision to the obstacle detection system for an excavator. The system consists of horizontally arrayed two digital cameras with low distortion lens, an image processing controller, and a monitor for an operator in the cab. Stereo vision calculates the depth image from images of two cameras and detects the presence of obstacles, its distance, direction, and dimensions. Sensed obstacles are informed to the operator in the monitor image. Preliminary experiments are conducted with a stereo vision system mounted on a real equipment in a demonstration site. The result shows that two controversial points of the conventional technologies are improved, and that the applicability of this system is validated.

Aug 1, 2013

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By Atsuki Sado, Akira Ueno, Kazuaki Takebayashi, Kunio Watanabe

The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® process in 2006 to improve product quality and productivity. After resolving various technical difficulties associated with the process, a current density of 325 A/m2 and electrolytic copper production of 234 000 tons per year were realized in 2018. In recent years, Saganoseki Smelter & Refinery has promoted treatment of recycled materials in addition to copper concentrates. Accordingly, the amount and type of impurities charged to the smelting process have tended to increase. In the electrorefining process, impurities such as nickel and antimony cause anodic passivation and formation of suspended solids, respectively. Although these undesirable phenomena can be avoided by controlling impurity concentrations in the anode and electrolyte to appropriate ranges, this also limits the choice of recycled materials that can be processed by the smelter. To achieve both stable operation of the electrorefining process and flexibility in treatment of recycled materials in the smelting process, Saganoseki Refinery improved the capacity of the impurity recovery processes during 2016 to 2018. This paper describes the expansion of the purification plant to remove and recover nickel and antimony. INTRODUCTION The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® (wax- less permanent cathode method) in 2006 to improve product quality and productivity. Since then, the refinery has gradually increased current density, and has been committed to establishing stable operation and high productivity via various improvements related to the electrolyte filtration and additive management systems. Figure 1 shows the trends of current density and current efficiency at the refinery. Although the current efficiency temporarily dropped when the current density was raised to 322 A/m2, it consistently exceeded 97% thereafter. At present, stable operation at 325 A/m2 has been achieved and continues.

Jan 1, 2019

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By George W. Bain

The area in Quebec immediately north of the Ottawa river is underlain by a large area of granite gneiss intruded in lit-par-lit fashion into Grenville sediments and low silica intrusives of the Buckingham Series. This complex of metamorphic rocks is intruded by a much later magma found, chiefly, as a very large stock about 20 miles in diameter and extending from Brownsburg to Grenville, and as dykes and small outliers at various places adjacent to its outer margin. 1A similar stock at Rigaud, Quebec, is situated south of the Ottawa river and has been described by O. E. Le Roy. The earliest representatives of the later magma are a series of granodiorite dykes characterized by abundant hornblende, along with primary magnetite and subordinate sulphides scattered as roundish grains through anorthoclase and aligoclase feldspars and subordinate quartz. The rock is found as narrow dykes and shows no prominent secondary structures, either in the field or in thin sections under the microscope.

Jan 1, 1926

This paper details a brief history of the Australian gold industry from the 1980s gold boom to the present day, highlighting an industry characterised by innovation in plant design and junior companies prepared to "have a go", in contrast to the conservatism of many larger mining companies. Design flexibility, the innovation of new processes, the preparedness to exchange "process know how" and technology singularly differentiated the gold industry from other sectors during the 1980s to the present. The introduction of two stage crushing, semi autogenous (SAG) milling, and pebble crushing, mill innovations, carbon in pulp (CIP) and carbon in leach (CIL) and the North Kalgoorlie screen etc were all exciting changes in the industry.

Jan 1, 2011

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016

By A. Sutherland Brown, Stuart S. Holfand

"The Northeastern part of the Cariboo district lies in the big bend of the Fraser River between Quesnel and McBride. The area shown on Figure 1 extends from just west of Wells to Isaac Lake, about 30 miles across the regional strike of beds.Topographically the area extends from the moderately well dissected Interior Plateau in the west through a transition zone to the fully dissected Cariboo Mountains in the east.The area is an important source of lode and placer gold. The Cariboo Gold Quartz and Island Mountain lode-gold mines have produced more than 32 million dollars in bullion since 1932. Placer-mining has probably produced an equivalent or greater amount, although only 15 million dollars is officially recorded because accurate statistics. were not kept until fourteen years after the origiiaal gold rush of 1860.The regional structure of the Barkerville district was summarized by Lang in the Jubilee Volume (1948, pp. 141-149). Since then a large amount of detailed and areal mapping by the writers has expanded the information available and made necessary a complete revision of the regional geology. Much of the information summarized in this paper, together with a full discussion of the revisions, may be found in British Columbia Department of Mines Bulletins, Nos. 34 and 38, but other information is as yet un-published.Rocks of the Kaza group are exposed in the core of the Lanezi anti-clinorium between Spectacle and Isaac Lakes. The main part of the group is composed of greenish micaceous greywacke and greenish schist with knots of garnet, biotite, or both, and minor amounts of pebble conglomerate. The upper 1,000 feet is composed of white to brown quartzites and brown phyllites. Altogether, about 6,000 feet of the group is exposed. 1t is of latest Precambrian, i. e. Windermere, age."

Jan 1, 1949

By M. Tanaka, H. Narita, K. Morisaku

"The selective separation of palladium (Pd), platinum (Pt), and rhodium (Rh) from a hydrochloric acid solution by solvent extraction was investigated using amide-type extractants, i.e., N,N,N’,N’-tetra-n-octyl-thiodiglycolamide (TDGA) and N-n-hexyl-bis(N-methyl-N-n-octyl-ethylamide) amine (BisAA). The separation experiments employed two separation schemes: (1) extraction of Pd with TDGA and that of Rh and Pt with BisAA; and (2) extraction of Rh, Pd, and Pt with BisAA. Separation scheme 1 achieved the highly selective separation of each metal. For separation scheme 2, Rh can be recovered prior to Pd and Pt, despite having a lower selectivity for Pd/Pt than separation scheme 1. INTRODUCTIONThe recent increase in the use of platinum group metals (PGMs) in industry (especially auto catalysts containing palladium (Pd), platinum (Pt), and rhodium (Rh)) has lead to their increasing waste; therefore, improvements in the recovery techniques for PGM have received significant attention. In metal refineries, PGMs are mainly separated and purified by solvent extraction (Cox, 2004). The extraction process used in INCO’s Acton precious metal refinery is one of the most famous commercial processes and is utilized worldwide. In this process, silver is first removed as a residue (AgCl), and then gold, Pd and Pt are extracted from hydrochloric acid (HCl) solutions using dibutylcarbitol (DBC), dialkylsulfide (DAS), and tri-n-butylphosphate (TBP), respectively. Finally, Rh remains in the raffinate (Barns & Edwards, 1982).The development of a successful solvent extraction process depends on the choice of the appropriate extractants. We have studied the extraction of PGM using N,N-disubstituted amide compounds (Narita, Tanaka, Morisaku, & Abe, 2004; Narita, Tanaka, Morisaku, & Tamura, 2006; Narita, Tanaka, & Morisaku, 2008a, 2008b). They are relatively stable against acids, and their metal extractability can be improved by changing the side chain length and/or introducing additional donor atoms like sulfur and nitrogen. We have recently found that thiodiglycolamide and an amide-containing tertiary amine have good extractabilities for Pd and Rh, respectively."

Jan 1, 2012

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By D. Purdie

"This paper aims to remind researchers, designers, operators, and managers about the benefits of seeding in the design of precipitation stages in their flowsheet. Including a high density solids (HDS™) process encourages the precipitating solids to form on the surface of existing precipitated particles. This paper discusses the application of the HDS technology at Kennecott Smelter, where the authors have witnessed significant improvements in settling and filtration rates. The authors have also applied this technology at various smelter bleed treatment plants worldwide with similar improvements in precipitation and filtration rates. HDS is a registered trademark of De Nora Water Technologies. RÉSUMÉ Cet article a pour objectif de rappeler aux chercheurs, aux concepteurs, aux exploitants et aux administrateurs les avantages de l’ensemencement dans la conception des étapes de précipitation de leur schéma de traitement. L’introduction d’un procédé des boues haute densité (procédé HDS™, de l’anglais high density sludge) encourage la formation de substances solides précipitantes à la surface des particules précipitées existantes. Cet article porte sur l’application de la technologie HDS à la fonderie Kennecott, où les auteurs ont observé des améliorations importantes au niveau de la vitesse de sédimentation et de filtration. Ils ont également appliqué cette technologie à diverses usines de traitement des rejets liquides des fonderies dans le monde entier, et ont constaté des améliorations similaires en termes de vitesse de précipitation et de filtration. Le procédé HDS est une marque de commerce déposée du fabricant De Nora Water Technologies.INTRODUCTION In 1966, the lead author worked as an assistant smelting metallurgist for the Tsumeb Corporation Limited copper and lead smelter in Tsumeb, Namibia. The smelter produced copper and lead, as well as cadmium and arsenic trioxide as byproducts. The cadmium was concentrated in the lead blast furnace off gas dust, and was collected by a baghouse. The baghouse dust was leached with dilute sulfuric acid (H2SO4) in a batch process. The iron and arsenic in the solution were oxidized with potassium permanganate (KMnO4) and basic ferric arsenate (BFAS; Fe(AsO4)x(SO4)y(OH)z·wH2O) was precipitated using milk of lime. The cadmium was cemented from the purified solution using zinc dust."

Jan 1, 2018

By E. I. Robinsky

"In light of the recurring spills and failures of conventional tailings disposal pond dams, a brief review of the Thickened Tailings Disposal (TTD) system is presented. It is shown that by the process of thickening the tailings to a heavy slurry prior to disposal, it is possible to create a self-supporting deposit of tailings and to eliminate the typical superimposed settling pond. These features, together with the ability to reclaim the disposal area even as mining continues, preclude an ecological disaster. IntroductionMine tailings spills are really not such rare occurrences. They have been happening on many continents, in many countries. Neither Canada nor the United States have been spared. In Ontario, the most recent spill occurred at a closed-down tailings disposal area in Matachewan, in 1991.Such continuing disasters could be avoided if a different approach were taken to the disposal of tailings wastes. The recent failures at the Los Frailes mine in Spain, the Omai mine in Guyana, and the Marcopper mine in the Philippines, will hopefully shake up the industry to consider other methods of disposal. The reason why the failure of a conventional tailings disposal dam is so environmentally disastrous is not the dam itself, but the fact that the dam retains a mass of very loose unconsolidated tailings and a great deal of water, or process fluid1. If the dam fails, the contents liquefy completely as they flow through the breach. In this liquid state, they can flow many miles downstream. If the dam itself were built of tailings material, as is often the case, it too would liquefy and join the flow.The reason the material is so loose in the first place is that it has been discharged into a pond filled with water. The tailings particles drift down through the water, their weight reduced by 50% due to buoyancy, to form a loose structure, like a “house of cards,” or lakebottom mud. It doesn’t take much of a shock to collapse the material into a liquefied state."

Jan 1, 1999