Search Documents

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006

By M. B. Mansur, A. S. Guimarães, A. J. M. Santanilla, D. C. R. Espinosa, J. A. S. Tenório, R. A. Pini

The separation of Ni and Co from sulphate medium containing Mn, Mg, Cu and Ca was carried out by solvent extraction. The object of this study was to investigate the synergistic effect using phosphinic acid (Cyanex 272) and carboxylic acid (Versatic 10) and their mixtures in kerosene. The extraction percent of each metal ion was found to increase with increasing pH and extractant concentration. Co was preferentially extracted over Ni under the same extraction conditions. The separation factors of Ni/Co increased with the use of the synergistic systems investigated.

Jan 1, 2014

By G. J. Arseneau

Mineral resource statements are reported as tonnage and grades. While great care is placed on generating a reliable estimation of grade, the determination of bulk density for resource estimation is often overlooked. Often mineral resource statements are prepared using a simple average value of bulk density. While a simple average estimate of bulk density can be appropriate for some deposit types, an over simplistic estimation of bulk density can result in serious errors in tonnage estimates and consequently to an over or under estimation of metal content. The construction of a reliable bulk density model requires an adequate bulk density database in order to develop a good understanding of the variability of bulk density with grade and geology. A reliable bulk density database is also essential in determining the appropriate modeling technique to minimize the errors in mineral resource statements caused by incorrect bulk density determinations. This paper summarizes bulk density measuring techniques and draws on examples from various deposit types examining the basic principles of bulk density modeling and domain construction for each deposit type. Examples are presented of simple bulk density domains and more complex grade variable bulk density domains with a discussion of best approaches for minimizing errors in density estimation.

Aug 1, 2013

By M. Greyling, C. Panaou, M. Bellino

Commonly the most frequent method of calculating the overall mass balance of a multi mineral platinum-group metal (PGM) concentrator circuit in Southern Africa has been through the use of spreadsheets, typically Microsoft EXCEL®. While there are some advantages in using spreadsheet based mass balances during the conceptual design phase of the project, their use becomes limited in the detailed design phase of the project. This paper discusses the successful application of METSIM® for mass balancing of a PGM concentrator and highlights the benefits gained during the conceptual and design phase of the project.

Jan 1, 2005

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

By G. Frithum

In the present paper a new and highly economic route for Fe-separation from HCl leaching processes in hydrometallurgical applications is described. In most ore leaching processes, Fe is involved and needs to be separated; HCl has become an interesting leaching agent, because it can be recycled. Usually a mix of Fe2+ and Fe3+ is obtained which can be hydrolyzed directly (in case only Fe3+) or roasted via pyrohydrolysis (in case of Fe2+) to ferric oxide. Economic oxidation of Fe2+ to Fe3+ is described, and potential technologies for regeneration of HCl with separation of Fe are shown and compared.

Jan 1, 2014

By N. Valkanov

This paper presents results of an investigation into the connection between minerals liberation management and flotation, responding to lead-zinc concentrator ?Erma reka?, in Bulgaria. Monitoring of a Zn flotation circuit was carried out. The causes for the high silica content in the final Zn concentrate were established. Quartz is present mainly as liberated particles (> 60?80 %) in the fine fractions of the products; therefore the selectivity of the flotation process is not effective. Two approaches were tested to reduce the quartz content of Zn concentrate: froth washing in Zn cleaner flotation and new gangue depressants in the Zn circuit. Experimental results from bench-scale flotation and industrial tests show that it is possibile to reduce the silica content of final Zn concentrate more than 2 times without the need for extensive regrinding. The depression of liberated quartz particles on all operations of Zn circuit using stage depressant addition is the right solution to produce high-grade Zn concentrate that meets the metallurgical requirements.

Aug 1, 2013

By X. L. Song, G. W. Zhang, F. Y. He, X. Xiao, L. L. Huang

This paper presents the design of a model and process simulation of a vertical mill based on a population balance model. The simulator, Simulink, which is a systematic modeling tool within MATLAB, was used for the simulation. The model will simulate the real time variation trend of each size fraction in the feed material to the vertical mill, as well as, the size distribution of the batch grinding products. Breakage distribution and selection functions are calculated based on batch grinding laboratory experiments using Back-calculation method. The simulated size distributions correspond with those in the actual mill operation having a relative error of less than 0.50%. This work lays the foundation for future research on modelling and simulation of a closed circuit grinding operation consisting of a vertical mill with hydrocyclone classifier.

Jan 1, 2016

By A. Bowles

The process of accumulative roll bonding (ARB) has been applied to wrought magnesium alloy AZ31. Accumulative roll bonding results in severe plastic deformation of sheet material. In AZ31, this process leads to the refinement of the microstructure by dynamic recrystallization. The refinement of the microstructure results in an improvement in mechanical properties with potential for producing materials for superplastic forming. In this work AZ31 was bonded with up to 64 layers and the potential of roll cladding with aluminium was also investigated. The development of microstructure and the mechanical properties are reported here.

Jan 1, 2006

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007

By T. Belem

In-stope backfill will cure under effective stress, which develops due to a combination of mechanical consolidation (free draining material) and ??chemical consolidation?? (self-desiccation mechanism). A good knowledge of all the drainage and consolidation characteristics of cemented paste backfill is crucial for a better design of underground backfilling sequencing. From many of the existing results and studies done by various authors, as well as the availability of some in-stope backfill pressure data measurements during and after filling, it is possible of developing a procedure of backfilling sequencing. Hence, the objective of this study is to provide a guide for underground backfilling sequencing in the view of preventing the development of excess pore pressure that will affect both the stability of the barricades and the strength development of the backfill. This will be possible by considering the interaction between consolidation/drainage rate, filling rate and binder hydration rate.

Aug 1, 2013

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By K. Oishi

We have developed a 76Cu-3Si-21Zn alloy "ECOBRASS®" containing no lead. When 3% Si is added to a 78Cu-22Zn alloy, kappa and gamma phases participate uniformly in the alpha matrix. When being machined, stress concentrates on these hard phases, namely kappa and gamma, and thereby lowering the required cutting force and yielding segmentalized chips without lubricant. Kappa and gamma phases transform into beta phase under high temperature, which makes it easier to extrude and/or forge the alloy. When 0.08% P and 50 ppm Zr are co-added, the grains of ECOBRASS® castings are refined significantly to become as small as several dozens of micrometers. The grain refinement by the co-addition of P and Zr improves castability, tensile strength and elongation of ECOBRASS® castings. Meanwhile, the lead leachate from an ECOBRASS® water meter, field-tested in pH 6.8 drinking water for one year, was less than 5 ppb without correction. No indication of dezincification corrosion was observed, either. ECOBRASS® is equally suitable for rods, forgings and castings, and makes it possible to produce a complete set of plumbing parts (valves, faucets, etc.) by its own. This way, not only improving recyclability, ECOBRASS® also realizes size and weight reduction due to its good corrosion resistance and high strength.

Jan 1, 2007

By R. W. Diamond

PUBLIC debts, and the policies guiding public finance in Canada today, are in such a state that every intelligent citizen should be familiar with them, and should be concerned about them. None of you have robe reminded that taxes have already risen to a point where they both annoy and hurt you, but they should also alarm you; alarm you, not so much because of the taxation, but because of the mounting expenditures represented by that taxation. I have no hesitation, therefore, in presenting a paper dealing with public finance at a meeting of the Mining Institute, since all present are concerned,. both as individuals and as representatives of the industry. Moreover, it is important that engineers, particularly, should become better acquainted with the interlocking relationships of economics, public finance, government, and technology. While I am neither an economist, a tax expert, nor a chartered accountant, I shall try to tell you, from my viewpoint as an engineer and an interested voter, the story of public finance in Canada today and of certain causes and effects, and I shall venture certain conclusions. In doing so I may merit criticism by experts, but I will risk this in the hope that sufficient interest will be stimulated in the subject to persuade you, as individuals and as groups, to advance, or to institute, your own studies in public finance, and in turn to interest others. I hope that some of the ideas which will be expressed, or which may develop, will bear fruit. I fully realize that several eminently qualified men have spoken on this subject during recent months, and that many authoritative articles have been written. However, I approach it with confidence, because I propose speaking to you not as an authority, bur as one of you, having similar interests and similar engineering knowledge, who only a few months ago became particularly interested in the subject, studied it, and who now sets before you a summary of his findings, with the conviction that the situation is so serious that constructive planning and constructive action by all thinking citizens are imperative.

Jan 1, 1939

By Pavel Vasak

Microseismic monitoring is becoming standard practice in the Canadian mining industry, particularly as mines get deeper. Full-waveform microseismic systems allow the operator to distinguish the event source mechanism, e.g., blast, shear slip or stress-induced fracture. At mine sites that heave a microseismic system operator blasts are manually identified by comparing the event waveform traces to the morning blast logs. However, this procedure is not routinely done at sites where a system operator is not present and this can lead to misinterpretation of the data at a later stage, particularly where the interpretation is outsourced, often many years later. It is critical to improve the microseismic data quality and consistency for processing and interpretation with a reliable technique to filter out blasts and blast related seismicity. This paper presents the development and implementation of a simple blast identification and filtering routine. The routine was developed specifically for Vale?s Creighton Mine about a decade ago, but is made sufficiently general so that it can be used at any mine site with an ESG (Engineering Seismology Group Canada) based full-waveform microseismic systems. The routine is strictly a post-processing procedure developed for use with the Access database data structure used by ESG. The algorithm was tested at Creighton Mine and a success rate of 80 to 90% was achieved, when compared to manual blast picks.

Oct 1, 2010

By J. Bhattacharya, S. K. Mukhopadhyay, S. K. Pal

"While time and again many authors have categorically stressed the restoration of the environment, very little effort has been made in the mineral industry to develop the economy of environmental control. There are many abatement procedures that search a maze of variants. Among them pricing environmental damage seems to be more logical and easily implementable.IntroductionMining as an operation has a severe impact on the Earth's natural resources. While economical environment control is much sought after, solutions are often varied and complex, and can differ in the problems of single or multiple mine sites.Determination of Optimum use LevelsIn “mining environmental control"" it is required to strike a balance to find optimum use levels. The solution is to find where the welfare benefits equal the cost involved to curb the degree of environmental damage (Fig . I) . In the mining industries this can be done by modifying the production/extraction process itself. For most pollutants, the marginal costs of control will exceed the benefits from further reduction of damage long before the zero pollution damage point is reached (Fig. I). From an economic perspective the optimal alteration of environment by mining would occur at z; pollution continues to be caused by ""zy"" control units, but it would be inefficient to pursue the redemption efforts further because the marginal cost involved would exceed marginal welfare benefits."

Jan 1, 1992

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By Murray D. Fredlund

The consolidation of soil material is central to many types of engineering analysis. Problems such as the building of highway structures, landfills, or buildings over saturated soft clays require application of such theory. It has been found in industry that the application of consolidation theory has lagged significantly behind the theory which has been developed some time ago. The application of small-strain saturated consolidation theory was first proposed in a 1D form by Terzaghi. Although this theory has been available for some time it?s implementation into software packages in 2D and 3D forms has been slow due to inherent complexities in the coupling equations. The flow and stress equations are also inherently somewhat unstable and this further complicates software implementation. Of particular interest in the mining industry is the consolidation of uranium tailings. One such disposal method that has been utilized is the subaqueous deposition of uranium tailings in large pit structures. When performing such deposition the calculation of consolidation rates is central to determining final pit capacity and expected life. Consolidation software can be successfully used in such cases in order to determine pit filling rates. The primary complexity, however, is that tailings are typically deposited in slurry form and therefore the potential deformations are large. Large-strain consolidation theory is therefore required in order to properly solve the deformations over time. This paper presents the use of a large-strain consolidation analysis in order to predict long-term filling rates in a uranium tailings pit.

Aug 1, 2010