Search Documents

By M. E. Bilir

In this paper, we review cases in which dramatic and visual swelling problems are experienced in underground structures. Swelling rocks have caused many problems in underground engineering projects. They pose severe problems to the design, construction and maintenance of underground openings. If an appropriate integrated design procedure, which proceeds from exploration, tests, analyses and realistic assumptions of swelling behavior, is used during the design stage, the execution of the project can be completed without any serious delays or dramatic design changes. The case histories were subdivided into three classes that include tunnels, underground coal mines and others. For the evaluation of cases, the surrounding rocks, swelling minerals, water inflow, swelling test results and swelling problems were considered. The main purpose of this review is to inform the reader about potential problems with swelling phenomenon and to emphasize the rehabilitation and extensive cost which are encountered due to the lack of necessary integrated design approaches.

Aug 1, 2013

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By R. L. Amelunxen

"In January 1983, Gibraltar Mines Ltd. started an exploratory program on Column Flotation with hopes of improving performance of the Molybdenum Cleaning circuit. The encouraging results led to a column test trial in the Bulk Copper Cleaner circuit where the test unit has per¬formed well. A program was undertaken to understand the mechanics of column operation. A year and a half later, Gibraltar is considering the replacement of existing Bulk Copper and Moly Cleaning flotation cells with a fully computer con¬trolled Column Flotation circuit.BRIEF SUMMARY OF TESTWORKInitial testwork was done with a home made 20 inch diameter x 31 foot high column, equipped with a doppler flow-meter at the tail line and automatic level conrol. This loop maintained constant level in the column by throttling the tail valve. This column was placed in a variety of locations around the Moly circuit as shown on Figure 1 a, b. Test re¬sults indicated that the column could achieve much higher grades than the conventional cells, but recovery wise, the performance was low. Spillages from overloaded pump boxes were a common frustration during this time.Column control strategy was reviewed; and, in light of information received from McGill University, changed to conform with the methods that had been employed by D. Wheeler, of the Column Co. of Canada4 and Gaspe Copper Mines3.The column was tested replacing a portion of the bank, figure lc. The results obtained were more or less equal to the circuit. However, as we had Nitrogen gas connected to the column and not the regular cells, the column was kept in service. With the use of Nitrogen in the column, the usual copper depressant, Sodium Cyanide could be replaced with Sodium Hydrosulphide, hence lower operating cost.As time went on, a 10 inch diameter column was added in series to re-treat the concentrate of the 20 inch diameter column with hopes that the copper content would decrease from 0.6% down to 0.3% in order to save on subsequent leach¬ing costs. So far, results indicate there has been some im-provement, hut we are not achieving 0.3% copper. (See figure 1d)."

Jan 1, 1985

By D. A. Sloan

"THE FIRST COMMENTATOR that I will call on is Mr. W. G. (Bill) Brissenden, Vice-President, Mines, Noranda Mines Ltd. Bill, would you care to comment.W. G. BRISSENDEN ...Mr. Chairman, Ladies and Gentlemen, I spent some time reading the four papers that were presented here, yesterday evening, and decided that the four to six minutes that I had been allotted for this afternoon were going to be pretty tough to meet. It's a very big subject and I just hope that I will be able to stay within my time limit. As has been so aptly demonstrated by the members of our panel here this afternoon young men in growing numbers continue to be attracted to careers in the mineral industry, especially to careers in mining engineering. Now from 80 the point of view that the profession may have regained its status this is indeed welcome news. However, perhaps all of the members seem to have the suspicion that the number of mining engineers that the industry can absorb is a much lower figure than previously forecast. It is said that technical school graduates are now occupying some of the jobs once considered the private preserve of the mining engineer and also that mining engineering undergraduates are having trouble locating summer employment. If these interpretations of mine are correct then we are now confronted not only with our old dilemma - whither the mining engineer - but also with an urgent need to solve it. We cannot allow our profession to become once again an undesirable one in the eyes of our youth because if we permit such a thing to happen a second time the profession may never recover."

Jan 1, 1972

By C. Yanqui

"Discontinuum Mechanics is based on two foundations: the idealization of the internal structure of substances, and the principle of the arithmetic mean value. For a linear discontinuum, the methods of Crystallography are used to describe their structure, in which nodes stands for the position of the homologous points such as molecules, grains, or any other motif. The principle of the mean value states that the value of any discrete function at a node is equal to the arithmetic average of the values of this function at the neighboring nodes. This principle leads to an elliptical linear differential equation of the second order, with coefficients given by the statistical second moments of the Cartesian components of the metric vector. As long as those coefficients are components of a symmetric second-order tensor, there are three mutually perpendicular directions, in which the variances reach their extreme values and the covariances are zero, showing that the mean value principle transforms the discontinuum into a statistically equivalent orthotropic continuum.The application of Discontinuum Mechanics to linear rock masses is simple and direct. It is sufficient to define the motif as the plane of geological discontinuity, and the metric vector as the normal vector to this plane, whose magnitude is the spacing between two consecutive planes belonging to the same set of discontinuities. Furthermore, heterogeneities of rock masses can be also included in this description by substituting the plane of discontinuity by a zone of weakness. In this way, the magnitude of the normal vector results from the product of the spacing and the RQD or the RMR. In going further in this theory, at least three conclusions show up. First, in the evaluation of rock masses, it is necessary to determine the orientation, spacing, and RMR for each set of discontinuities. Second, the conventional method of finding the principal families from the contours of equal concentration of poles on the stereographic projection excluding the spacing does not have any physical meaning. Third, any problem of rock mechanics can be solved in a rigorous and reliable way by integrating the differential equation of the mean value."

Jan 1, 2015

By Chen Xia, G. Deschenes, Wan-Tai Yen

"Ammonium thiosulphate is a potential replacement for the cyanide in gold leaching. However, the high reagent consumption hinders its practical applications. In order to reduce the thiosulphate consumption, chemical additives were used. The gold leaching tests were conducted on a sulphide copper-bearing gold ore with 0.3M thiosulphate, 0.03M copper sulphate and 3M ammonium hydroxide solution at 44% solids and pH 10.2. Sulphate, sulphite, amino acid and chelating agents were initially used as additives. It was found that chelating agents (EDTA and NTA) could reduce the thiosulphate consumption from 30 kg/t to 17.8 kg/t with some increase of gold extraction. The improvement from other additives was not significant. Other approaches were also attempted to reduce thiosulphate consumption with some success. The thiosulphate consumption could be reduced to about 17 kg/t by reducing copper sulphate concentration fiom 0.03M to 0.0015M; adding 0.04M of EDTA; replacing copper sulphate with 0.001M of nickel sulphate. The increase of pulp density fkom 44% to 60% solids could reduce the thiosulphate consumption to 17 kg/t as well. Limiting the dissolved oxygen content by sparging nitrogen reduced the thiosulphate consumption further to 10 kg/t. It could be concluded that the regulations of copper and oxygen supply in the lixiviant were the keys to reduce the reagent consumption.INTRODUCTIONCyanidation, as the predominant gold leaching method, has been used in mining industry for more than a century. The low reagent requirement and the high performance are the reasons for its great success. However, cyanidation cannot deal with ores containing large amount of copper, nickel, arsenic and zinc minerals. This type of ore may consume more reagents and result in a poor gold extraction. On the other hand, the carbonaceous materials may preg-rob the gold from pregnant solution and make cyanidation a problem leaching method. Further more, the high toxicity of cyanide represents another challenge to modern gold mines. In the beginning of the year 2000, an environmental disaster caused by an accidental spill in Yugoslavia was broadcasted world-widely (Gurevitch 2000). Gold mine operators are facing higher social pressures and increasing costs on environmental protections. The usage of cyanide in mining industry has been banned in some countries and locations such as Czech Republic, Japan, Turkey, California, Colorado, Wisconsin and Montana States. Thus, a non-cyanide lixiviant is required."

Jan 1, 2002

By E. Fried

Cemented paste backfill (CPB) is an innovative tailings management method that consists in returning considerable amounts of mine tailings into the underground mine openings. The filled stopes thus participate to the ground support that allows maximizing orebody extraction and a safer environment for the mine workers. There are also significant environmental advantages of using CPB. Indeed, up to 50% of the concentrator tailings can be backfilled, leading to a smaller volume of problematic waste materials to be managed at the surface. Once the CPB is placed, or when the mine is flooded at its end-life, the backfill is subjected to underground water flows that may leach and spread the pollutants (mainly metals, sulphates, and acidity) which can contaminate the underground waters. The aim of this study is to characterize the leaching properties of CPB material and to identify the cement phases that ensure the metal fixation. A laboratory procedure was implemented consisting in the preparation of various paste backfill mixtures using sulphide-rich and sulphide-free materials, different types of binder, and mixing waters having various sulphates, copper and zinc concentrations. After 90-days curing time, the samples were submitted to column leaching tests. The CPB materials were flushed each day with 100 ml of deionised water during 100 days. The collected leachates were then analyzed for pH, Eh, electric conductivity and chemical composition. For some samples, a differential acid neutralisation test was carried out. The objective of this experiment is to dissolve selectively the hydrated phases by adding incremental acid concentrations. By analyzing punctually the equilibrated solutions, the composition of the dissolved phases and their metal content can be estimated. The leaching test results showed that the pH of the leachates remains alkaline during the test period. When the pH decreases under 10 (after 30 days), different behaviours in terms of chemical element release (especially for zinc) were observed. During the test, the oxidation of pyrite seems to slow down, probably due to passivating phenomena. Moreover, the differential acid neutralisation test results allowed a better understanding of the CPB mineralogy and the Zn-bearing cement phases. Zinc and the other metals seem to be fixed within a calcium-magnesium silicate.

May 1, 2007

By J. Patterson

"Acid Mine Drainage (A.M.D.) formed from oxidation of disposed pyritic wastes presents a potential pollution hazard for Equity Silver Mines Limited and the mining industry in general. Failure to collect and treat these acidic effluents can eventually affect the quality of receiving streams and endanger aquatic life forms. Treatment and discharge of A.M.D. to the receiving environment must comply with stringent anti-pollution laws.Wastes mined at Equity Silver Mines Ltd. are predominantly acid generating and must be handled according to a materials management plan to minimize impact on the environment. Effluent collection and treatment facilities have been constructed to address the short term environmental concerns with reclamation and research programs being developed to address and monitor abatement measures for control over the long term.The purpose of this paper will be to offer a brief overview of these measures. Key topics for discussion will be: kinetics of Acid Mine Drainage, acid generating potential, water treatment and sludge handling, special wastes, waste dump construction, waste rock amendments, bacteriocide research, simulations, and reclamation measures. Programs designed to evaluate impact on the receiving environment, although they form an extensive part of the program, will not be discussed in this paper.INTRODUCTIONEquity Silver Mines Limited is located in the Central Interior of British Columbia, within the Omineca Division, 35 kilometers southeast of Houston Mining and approximately 575 kilometers by air north-northeast ofVancouver (Figure 1).The deposit consists of three economic mineralized zones: The Southern Tail, Main and Waterline Zones. Mining of the Southern Tail commenced in April, 1980 and was completed in the first quarter of 1984. Main Zone production was initiated during the last quarter of 1983 and the Waterline Zone remains undeveloped to-date. Remaining reserves are in the order of four years contingent on favourable metal prices. The three deposits (Figure 2) occur within a window of interbedded volcanic and minor sedimentary rocks. The older volcanic sequence is bounded on the west by a small granite-like stock and on the east by a gabbro-monzonite complex. All are overlain by a series of younger lava flows."

Jan 1, 1988

By Andy Cole, Ken Thomas, Stephen Durn, Jacques McMullen

"The roasting and gas handling circuits of the Barrick Gold’s new Roasting Facility at the Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Product from the up-stream dry grinding circuit requires roasting to maximize gold recovery. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type “double refractory” ores. Double refractory is indicative of the gold being difficult to direct leach due to a combination of pyrite encapsulation and the carbonaceous preg-robbing of the ore.A very extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NO, reduction before venting to the atmosphere.The roasted calcine is quenched, neutralized and then thickened before leaching in the carbon-in-leach-circuit.INTRODUCTIONBarrick’s strategic development plan integrated the production of gold from Goldstrike’s carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1 996. Processes considered included autoclaving followed by a proprietary ammonium thiosulfate leaching process, fine grinding/autoclaving as practiced then by Santa Fe, and whole ore roasting as practiced by then Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike’s carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated."

Jan 1, 2001

By C. H. Stockwell

RICE LAKE-BERESFORD LAKE area, situated 100 miles northeast of Winnipeg (Figure 1), is Manitoba's foremost gold mining district, although it is exceeded in gold production in the Province by the Flin Flon base-metal mining district. At present, the area is producing at the rate of about one and three-quarter million dollars annually, almost entirely from the San Antonio and Gunnar mines. The total production to date is about $14,000,000. Of this total, over $7,000,000 has come from the San Antonio mine, over $2,000,000 from the Gunnar mine, about $4,000,000 from the Central Manitoba mine, and the balance from several smaller properties. The writer has led Geological Survey parties in the area for the past four summers. The present paper gives a summary of the results of this work and also includes the findings of C. S. Lord, who was in charge of a party for one year. Much valuable information was obtained from earlier published reports on the area and from officials of mining companies, to whom the writer is indebted for their kindly co-operation. It is impossible in this short paper to give proper credit to the earlier workers or to discuss certain points o disagreement between their conclusions and those presented here. For further information the following references may be consulted.

Jan 1, 1940

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By M. B. McClenaghan

"Abstract- The Ontario Geological Survey completed a regional till sampling project between 1984 and 1988 in the Black River Matheson (BRiM) area of northeastern Ontario. The project was designed to aid mineral exploration in the area by documenting the Quatemary stratigraphy and by providing a database of till geochemistry. This paper summarizes the results from the sonic overburden drilling component of the BRiM project carried out in areas of thick drift (> 5 m). Results from till sampling in areas of thinner drift (<5 m) have been presented in a separate paper. Approximately 1100 till samples were collected from 225 sonic drill holes. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically and visible gold grains were recovered by panning.Gold and other multielement geochemical data were plotted using proportional symbols to high­ light anomalous areas and to demonstrate how to evaluate and interpret a very large geochemical dataset. Thresholds for identifying anomalous concentrations of Au in till samples, defined using the 95th percentile, are 1500 ppb and 12 ppb for the heavy mineral and fine fractions, respectively. The heavy mineral fraction of older tills and to a lesser extent, Matheson Till, display a number of significant gold anomalies in the study area, which in a few cases, are associated with base metal anomalies. The vertical position of gold anomalies in Matheson and older tills varies from directly on bedrock to several meters above the bedrock surface and can provide information of relative ice transport distances."

Jan 1, 1994

By J. P. Jarrell

Environmental considerations are of increasing importance in determining the acceptability, schedule and cost of expansion ofCanada&apos;s uranium processing industry. Environmental considerations must be addressed in the early stages of facility planning. This results in a dilemma, as the process data needed to predict physical environmental impacts are not yet available from process design activities. Hence, a business risk is incurred if plant design is carried forward to meet these requirements prior to project (or site) approval. On the other hand, project scheduling normally mitigates against leaving process design engineering until such time as project approval is obtained. This paper examines the experience gained in Eldorado Nuclear&apos;s proposed expansion of refining capacity as viewed by an environmental engineering consultant. The history of the project and the relationship to process design functions in the two-year period prior to the Port Granby environmental hearings are reviewed. During the Port Granby public hearing, there was a consensus that normal operation of the proposed refinery could be successfully integrated with the site&apos;s natural environmental constraints. Moreover, the radiological impact from plant operations was demonstrated to be inconsequential. However, concerns were raised relating to plant upset and accident situations. These concerns are summarized. Process data requirements identified during the environmental hearings are discussed. Finally, the concerns for on-site burial of radioactive waste are reviewed. These concerns focussed on long-term stability of the waste in the presence ofgroundwater transport, erosion and glaciers. The AECB&apos;s position on waste management with regard to this project is reviewed in light ofthe implications for design.

Jan 1, 1979

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By P. W. A. Mayer

"As the push toward the northern regions of Canada steadily increases to exploit the rich mineral reserves, interest is steadily rising in respect to accessibility and climatic conditions and the problems posed thereby. In twelve years of operation, the Iron Ore Company of Canada, and associated companies, have found, through advanced technology, ingenuity and, most of all. need, some of the answers to the running of a profitable year-round open-pit mining operation."

Jan 1, 1966

By L. Dorador

"In block caving projects, the rock mass fragmentation process plays a controlling role in the design and success of the operation. Poorly understood, however, is the secondary fragmentation that occurs as blocks of caved ore move through the draw column and interact with one another. The initial size of these blocks can be considerable, as can their strength and stiffness as the presence of non-persistent joints and veining will be variable. Intuitively, more planes of weakness within the blocks should facilitate early fragmentation, but this assumption could depend on additional factors such as contact type between adjacent blocks and loads imposed through varying heights of the draw column. This paper reports the findings from a laboratory investigation examining the role of block strength and planes of weakness on secondary fragmentation. Testing was carried out on small-scale concrete cubes of uniform size, with and without embedded planes of weakness. The results obtained demonstrate the significance of veining and other planes of weakness on secondary fragmentation under one-dimensional compression, and allow for the development and constraint of empirical guidelines.INTRODUCTIONThe fragmentation process during block caving involves the initial (primary) fragmentation of rock in the cave back through stress-induced fracturing, release and fall of individual blocks onto the broken ore muck pile. This is followed by secondary fragmentation involving splitting and rounding of blocks as they move downwards through the draw column towards the draw point. The degree of secondary fragmentation achieved involves many variables related to the mechanical properties of the rock blocks as well as different operational factors. With respect to the block properties, the presence of planes of weakness in the form of veining and non-persistent joints is a topic of special interest given the significant influence it potentially has on the overall fragmentation process. However, the inherent heterogeneity and variable size of individual blocks generated from the cave back makes it difficult to develop any empirical relationships relating secondary fragmentation to compressive loading based on insitu observations and mine data. More preferable would be to keep constant block parameters, such as shape (aspect ratio and angularity) and size, through controlled laboratory testing. This work presents an efficient technique to fabricate concrete cubes in order to keep constant different block properties. These are then tested under one-dimensional compressive loading. The objective of these tests is to emulate a tight packing condition of single blocks such as that which would occur when the air gap between the cave back and broken ore in the draw column is small. When the air gap is small, detached blocks are unable to fall and rotate but instead maintain a very tidy arrangement with minimal voids left between adjacent blocks."

Jan 1, 2015

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

By A. M. Girodo

"Dorbyl Heavy Engineering has been manufacturing winders since 1949 mostly for the South African mining industry.Table 1 shows that the vast majority of winders have been double drum winders. At the greater depths with larger ropes being employed, it became apparent that multi-rope winders would be needed. The high stress variation in Koepe winder ropes at great depths especially beyond 2000 m, ruled out this possibility. Thus the original concept was borne for the Blair multi-rope winder where the stress level variations in the rope would be as per the well known, tried and tested double drum winder. The Blair multi-rope was also devised to increase payload by using multiple ropes.With the increasing costs of transporting men and material coupled with fact that orebodies are getting deeper, various feasibility studies have been carried out by South African mining houses. For this reason Dorbyl Heavy Engineering has done conceptual design work of both double drum and Blair multi-rope winders with diameters up to 8.5 m dia (still well within our manufacturing capabilities). These feasibility studies have looked at depths approaching 4000 m*.This paper covers the typical duties leading to the choice of single drum, double drum, Koepe and Blair multi-rope hoists on South African gold mines. A brief synopsis of Dorbyl hoists in use in the South African mining industry, with some indications of future trends, will be discussed.With current installed depths of wind approaching 2500 m, the Blair multi-rope hoist has been used extensively for the heavier payloads.Some of the main considerations pertinent to the design of the Blair multi-rope hoist are illustrated together with the implications of using this type of hoist to winding depths of3000 m to 4000 m in the foreseeable future."

Jan 1, 1995

By Hasan Ozturk

Laboratory testing examined the effect of a variety of intrinsic rock properties and environment conditions that influence the adhesive bond between rock and thin spray-on liners. The liner materials used for these tests were Tekflex, provided by Fosroc, Castonite, provided by Rohms and Haas Co., Rockweb provided by Spray-on Plastics, and CS 1251 2K, provided by Master Builders. Some of the variables examined include: rock strength (tensile/compressive strength) rock mineralogy, rock surface roughness (grain size, fracture/joint roughness), and surface contamination (oil, water or dust). Under optimal conditions, adhesive strengths reaching at least 3 MPa can be achieved. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa.

May 1, 2004